A.J.Antunes roundup EST-3 Installation guide

Brand: A.J.Antunes

Model: roundup EST-3

Category: Electrical timers

Type: Installation guide

A. J. ANTUNES & CO.

180 Kehoe Blvd., Carol Stream, Illinois 60188

INSTALLATION INSTRUCTIONS

SONIC FRY STATION TIMER EST-3 (MFG. #9900651) & EST-3LS (MFG. #9900652)

General

If you experience any problems with these instructions,

contact the factory Technical Service Department at 630-

784-1000 or toll free in the U.S. at 877-392-7854.

Before You Begin

The Fry Station Timer (EST-3 and EST-3LS) is designed

to track the holding time for Tots, French Fries, and

Onion Rings. This helps stores provide consistently high

quality products.

The Fry Station Timer has three independent timer chan-

nels that track the proper holding. The Timer is solar

powered and mounts easily to the top of the Fry Station

with a supplied Mounting Bracket (Figure 2).

Three AA power backup batteries are included. The

EST-3LS also features an audible signal.

Installing the Fry Station Timer

NOTE: Do NOT obstruct the solar cells at the front

and top of the Timer or the Timer may not function

properly.

NOTE. Do NOT locate the Timer in areas hotter than

120ºF (49ºC).

1. Take the Timer out of the box.

2. Attach the Timer to the screws on the canopy.

NOTE: In almost all cases, the canopy will have the

preexisting screws needed to hang the Timer. If your

canopy does not, then use the following steps to

mount the Timer.

1-877-392-7854 Fax: 630-784-1000 Page 1 of 2 P/N 1011049 Rev. A 02/10

Sonic

WARNING

Do NOT locate the timer in areas hotter than

120ºF (49ºC).

PARTS INCLUDED:

1 EST-3 Fry Station Timer (P/N 9900651) OR

EST-3LS Fry Station Timer (P/N 9900652)

1 Instruction Sheet (P/N 1011049)

TOOLS NEEDED:

Phillips Screwdriver, Permanent Marker, Power Drill,

9/64” Drill Bit (hardened steel), Center Punch (automat-

ic or manual), Hammer (if using manual punch).

Figure 1. Fry Station Timer (EST-3LS shown)

Figure 2. Fry Station Timer (Rear View)

a. Remove the Timer from the Mounting Bracket.

b. Place the Mounting Bracket against the canopy.

Level it, and use a permanent marker to mark two

spots on the canopy for drilling.

c. Place the tip of a center punch on each mark and

carefully strike to create an indentation for the drill

bit. Be careful not to dent the fry station canopy.

d. Place a 9/64” drill bit (hardened steel) into your

drill as far as possible so only the minimum bit is

exposed.

e. Drill the two holes. Be careful to only penetrate the

canopy and not damage any wiring that may be

present.

Mounting

Bracket

1-877-392-7854 Fax: 630-784-1000 Page 2 of 2 P/N 1011049 Rev. A 02/10

Sonic

A. J. ANTUNES & CO.

180 Kehoe Blvd., Carol Stream, Illinois 60188

INSTALLATION INSTRUCTIONS

SONIC FRY STATION TIMER EST-3 (MFG. #9900651) & EST-3LS (MFG. #9900652)

f. Use a Phillips screwdriver to screw two #8-18 x

1/2” lg. self-tapping screws into the stainless steel.

Do NOT overtighten the screws. Allow space for the

brackets to fit over the screws.

g. Mount the bracket onto the screws and then finish

tightening the screws with the Phillips screwdriver.

h. Re-install the Timer onto the Mounting Bracket.

i. Place a lock washer on the inside and outside of

each side of the Mounting Bracket and then secure

in place with the thumb screws.

Using the Fry Station Timer

The Fry Station Timer is pre-programmed at the factory

with the following values:

Description

& Value

Default

Setting

Max Setting

Tots 10 minutes

99 minutes,

59 seconds

French Fries 10 minutes

99 minutes,

59 seconds

Onion Rings 10 minutes

99 minutes,

59 seconds

1. Press the ► button (Figure 3) for the desired prod-

uct and the timer will begin counting down.

2. When the timed cycle is complete, the display

flashes “00:00”, the blue light will flash once every

second, and the unit will beep (EST-3LS only).

NOTE: After two minutes, the blue light will flash

once every two seconds, and the unit will stop beep-

ing (EST-3LS only). After five minutes, the blue light

will stop flashing.

3. Press the

■ button (Figure 3) to stop and reset the

Timer.

NOTE: If the display is faded, or if the volume is too

low (EST-3LS only), the three AA backup batteries

should be replaced.

Limited Warranty

The Fry Station Timer (EST-3 and EST-3LS) has a 90-day warranty from date of purchase. This warranty does not cover

misuse/abuse, damage due to dropping, cover damage, and/or cracked solar panels. The warranty for this timer does

not cover travel time or mileage. Contact the Technical Service Department at the factory for any warranty issues.

Figure 3. Fry Station Timer (EST-3LS shown)

Programming the Fry Station Timer

1. Press and hold the ► button for the desired product

for three seconds.

2. The minutes setting will flash on the display. Use

the ► and

■ buttons (Figure 3) to raise and lower

the setting.

3. Release the buttons when the desired minutes

setting appears on the display.

4. The seconds setting will flash on the display. Use

the ► and

■ buttons to raise and lower the setting.

5. Release the buttons when the desired seconds

setting appears on the display.

6. Wait three seconds without pressing any buttons.

The new settings will be stored and the display will

go blank.

Problems with the Timer?

If you experience any problem with your Timer, contact

the manufacturer immediately at 877-392-7854.

NOTE: A replacement battery cap can be obtained

through your Authorized Service Agency by ordering

P/N 7000573.

A.J.Antunes roundup EST-3 Installation guide

Brand: A.J.Antunes

Model: roundup EST-3

Category: Electrical timers

Type: Installation guide

Download PDF

report

A.J.Antunes roundup EST-3 Installation guide

A.J.Antunes roundup EST-3 Installation guide

Other documents