Nady CPD-1006L Owner's manual

Brand: Nady

Model: CPD-1006L

Type: Owner's manual

RACK GEAR

CPD-1006L

Conditioned Power Distribution

OWNER’S MANUAL

CPD-1006L

Conditioned Power Distribution

• 10 AC sockets: 2 unfiltered front panel and 8

conditioned, with six-step delayed sequence turn-on/off

• 2 second sequence interval standard — factory

adjustable also to 1 or 3 seconds

• Superior RFI/EMI filtering and surge protection

• Extremely accurate system voltage meter with 3-digit

LED numeric display

• Retractable, rotating, 6 LEDs lamp for long-life front rack

illumination

• Rack light Hi/Off/Low dimmer switch

• 15A circuit breaker

Congratulations on your choice of the finest conditioned

power distribution unit. This unit was developed using the

expertise of professional sound engineers and working

musicians. You will find that your new NADY AUDIO

CPD-1006L has superior performance and greater

flexibility than any other conditioned power distribution

units in its price range. Please read this manual carefully

to get the most out of your new unit.

Thanks for selecting NADY AUDIO as your choice in

conditioned power distribution units.

Date of Purchase

Dealer’s Name

City

State

Zip

Model #

Serial #

Features ......................................................................2

Warning ......................................................................3

Controls and Connections ..........................................4

Specifications ..............................................................5

Notes ..........................................................................6

FEATURES

CONTENTS

BLACK

WARNING

IMPORTANT SAFETY INSTRUCTIONS

When using this electronic device, basic precautions should always be taken, including the following:

1. Read all instructions before using the product.

2. Do not use this product near water (e.g., near a bathtub, washbowl, kitchen sink, in a wet basement, or near a

swimming pool, etc.).

3. This product should be used only with a cart or stand that will keep it level and stable and prevent wobbling.

4. This product, in combination with headphones or speakers, may be capable of producing sound levels that

could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a

level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an

audiologist.

5. The product should be positioned so that proper ventilation is maintained.

6. The product should be located away from heat sources such as radiators, heat vents, or other devices

(including amplifiers) that produce heat.

7. The product should be connected to a power supply only of the type described in the operating instructions or

as marked on the product. Replace the fuse only with one of the specified type, size, and correct rating.

8. The power supply cord should: (1) be undamaged, (2) never share an outlet or extension cord with other

devices so that the outlet’s or extension cord’s power rating is exceeded, and (3) never be left plugged into

the outlet when not being used for a long period of time.

9. Care should be taken so that objects do not fall into, and liquids are not spilled through, the enclosure’s

openings.

10. The product should be serviced by qualified service personnel if:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen into, or liquid has been spilled onto the product.

C. The product has been exposed to rain.

D. The product does not appear to operate normally or exhibits a marked change in performance.

E. The product has been dropped, or the enclosure damaged.

11. Do not attempt to service the product beyond what is described in the user maintenance instructions. All

other servicing should be referred to qualified service personnel.

1. UNSWITCHED CONVENIENCE OUTLET

These 25A outlets always provide unfiltered power, even when the CPD-1006L is switched off. They

are not controlled by the delay switches nor connected to the

15A Circuit Breaker (2).

15A CIRCUIT BREAKER

The CPD-1006L’s current rating is 15A (max). If the current draw of the connected equipment

exceeds 15A, the breaker will trip and cut off the power. Disconnect some equipment or otherwise

lower the current draw to enable use of this unit. You can then turn on the power again by pressing

the breaker button.

POWER SWITCH

When it’s switched to “ON” the unit will provide power to the outlets sequentially from Zone 1

through Zone 6 in turn. The sequence delay time is factory set at 2 seconds, but can be factory

adjusted also to 1 or 3 seconds (contact the Nady Service Department to change internal delay

adjustment). The sequence for powering off will be reversed when it’s switched to “OFF”. When

“ON” the

Zone Indicators Display (4) and Voltmeter Display (5) will light up.

ZONE 1 - 6 DISPLAY

The LED indicators will light or turn off indicating when components connected to the ZONE

1/2/3/4/5/6 outlets are powered on and off.

VOLTMETER DISPLAY

When the unit is powered “ON”, this 3-digit display will light and indicate numerically the supply

voltage to the entire audio system connected to the Zone outputs.

LED RACK LAMP

To illuminate your unit and other rack gear mounted below it, pull out the retractable LED light and

rotate to angle desired (+/- 30° from vertical). The lighting is adjustable with the

Dimmer Switch (7).

DIMMER SWITCH

To adjust the illumination level of the LED Rack Lamp (6) select either “HIGH” (for brightest light),

“OFF”, or “LOW” (for dimmest light).

CONTROLS AND CONNECTIONS

FRONT PANEL

(3)

(2)

(1)

(4)

(6)

(7)

(5)

Current Rating ......................................................................................................................................................15 Amps

Filtered Sequenced Outlets..............................................................................................................................................8

Sequential Zones ........Zones 1-4 (for digital equipment, 5A max.), Zone 5 (2 outlets, for analog equipment, 10A max.),

Zone 6 (2 high-power outlets,15A max.)

Filtering ..................................................................................................................................................................RFI/EMI

Sequence Delay Time ......................................................2 seconds, internally factory adjustable also to 1 or 3 seconds

Switching Response Time ..........................................................................................................................1 nanosecond

Zone Indicators ....................................................................................................................................6 LEDs, Zones 1-6.

Rack Lamp ................................................................................................Single retractable, swiveling 6-LED light fixture

Input AC Voltage ..............................................................................................................................................90~140 VAC

Voltmeter Display ........................................................................................................................................3-Digit numeric

Maximum Surge Current ........................................................................................................................................6,500 A

Dimensions ............................................................................................................19’’ x 1.73’’ x 7.5’’ (483 X 45 X 190mm)

Weight ........................................................................................................................................................8.5 lbs. (3.9 Kg)

Specifications and design subject to change without prior notice for improvement purposes

CONTROLS AND CONNECTIONS

(11)

(10)

(9)

(8)

8. POWER CORD

Connect power cord to AC source (120VAC, 16A minimum) before turning unit “ON”.

CHASSIS GROUND

Use a wire connected from this terminal to system ground for best results and to eliminate ground

loop hum.

10.

GROUNDING INDICATOR

The LED will light to indicate good grounding status. If it doesn’t light, connect a wire from the

Chassis Ground (9) to system ground until the LED lights.

11.

ZONE 1-6 AC OUTLETS

These outlets have three kinds of filter (digital filter/analog filter/high power), which are designed to

reduce the noise to your connected digital/analog/high current components. Zones 1-4 are rate 5A

maximum and are for connecting lower draw digital components such as a CD player, or computer.

Zone 5 (2 outlets) are rated 10A maximum and are for connecting medium power analog units such

as mixers. Zone 6 (2 outlets) is rated 15A maximum and should be used for connecting high power

components such as power amplifier. When the CPD-1006L is turned on, the digital and analog

outlets, Zones 1-5, are switched on first in 2 second sequential intervals, and then the high current

Zone 6 outlets are switched on. This delayed sequencing protects speakers connected to the

amplifiers from the turn-on noises of the equipment connected to Zones 1-5. Powering “OFF” is the

reverse sequence and protects the speakers from any turn-off noises generated by the equipment

connected to Zones 1/5.

REAR PANEL

SPECIFICATIONS

NOTES

Pantone 185 Red/Black/Cool Gray 40%

BLACK

NADY SYSTEMS, INC. • 6701 SHELLMOUND STREET, EMERYVILLE, CA 94608

Tel: 510.652.2411 • Fax: 510.652.5075 • www.nady.com

SERVICE FOR YOUR NADY AUDIO PRODUCT

(U.S.) Should your NADY AUDIO product require service, please contact the Nady Service Department via

telephone at (510) 652-2411, or e-mail at service@nady.com.

(International) For service, please contact the NADY AUDIO distributor in your country through the dealer from

whom you purchased this product.

DO NOT ATTEMPT TO SERVICE THIS UNIT

YOURSELF AS IT CAN BE DANGEROUS

AND WILL ALSO VOID THE WARRANTY.

Nady CPD-1006L Owner's manual

Nady CPD-1006L Owner's manual

Nady CPD-1006L Owner's manual

Related papers

Other documents