Glacier Bay HD461-8216 Installation guide

THANK YOU

INSTALLATION AND CARE GUIDE

TWO-HANDLE ROMAN TUB FAUCET

We appreciate the trust and condence you have placed in Glacier Bay through the purchase of this roman tub

faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see

our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!

Questions, problems, missing parts?

Before returning to the store, call Glacier Bay Customer Service

8 a.m. - 7 p.m., EST, Monday - Friday

9 a.m. - 6 p.m., EST, Saturday

1-855-HD-GLACIER (1-855-434-5224)

HOMEDEPOT.COM

12/2017 REV.01HOMEDEPOT.COM

Model#

HD461-8204

HD461-8216

Internet#

304368025

304367678

SKU#

1003002573

1003002776

Phillips

screwdriver

Basin

wrench

2

Table of Contents

Important Information ..............................2

Warranty ...................................................2

Pre-Installation .........................................2

Planning Installation ..............................2

Package Contents ..................................3

Installation ................................................4

Care and Cleaning ....................................7

Troubleshooting ........................................7

Service Parts

...........................................

8

Important Information

□ Observe all local plumbing and building codes.

□ Cover the sink drain to avoid losing any parts.

□ Review the care and cleaning section included in this guide.

Pre-Installation

PLANNING INSTALLATION

Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package

Contents list. If any part is missing or damaged, do not attempt to install the product. Contact Customer Service

for replacement parts.

TOOLS AND HARDWARE REQUIRED

Adjustable

wrench

Safety

goggles

(2) Supply

lines

Tools and Hardware Required ...............2

Operation...................................................7

Warranty

LIMITED LIFETIME WARRANTY

Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our

limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of

defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.

Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER (1-855-434-

5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer

purchaser must be made available for all Glacier Bay warranty claims.

This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and

tear. This warranty excludes all industrial, commercial and business usage, whose purchasers are hereby extended

a ve year limited warranty from the date of purchase, with all other terms of this warranty applying except the

duration of warranty.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other

rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for

more details.

Contact the Customer Service Team at 1-855-434-5224 or visit www.HomeDepot.com.

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

3

Pre-Installation (continued)

PACKAGE CONTENTS

Part Description Quantity

G Rubber washer 1

H Metal washer 1

I 1

K Set screw 2

Mounting nut

J 2Handle

Part Description Quantity

A Spout assembly 1

B Set screw 1

C 3.2mm hex wrench 1

F Middle body 1

P Protective cap 2D Protective cap 1

E Connector 1

L 2.5mm hex wrench 1

M Handle seat 2

N Set screw 2

O Connector 2

T Rubber washer 2

U Metal washer 2

V 2

W Hose 2

Mounting nut

Q Flange 2

R Hot end valve 1

S Cold end valve 1

A

B

C

J

K

L

M

N

O

G

H

I

F

D

E

P

Q

S

T

U

V

R

W

4

Installation

1

Preparing for installation

CAUTION: Always shut off the water supply before

removing an existing faucet or replacing any part of a

faucet. Open the faucet handle to relieve water pressure

and ensure that the water is completely shut off.

2

Removing the mounting kits

□ Remove the protective cap (D). Loosen the

connector (E) from the middle body (F). Adjust

the rubber washer (G), metal washer (H) and

mounting nut (I) to the bottom of middle

body (F).

□ Shut off the water supply. Remove the old

faucet.

□ Clean the mounting surface.

□ Drill holes in the nished deck as shown in

the diagram below.

5 in. min.

8~16 in.

3 in. min.

1-1/4 in. MAX. DECK THICKNESS

1-3/8 in.

Diamter

1-1/8 in.

Diamter

1-3/8 in.

Diamter

NOTE: This kit allows up to 1-1/4 in. deck thickness.

3

Installing the middle body

□ From underneath the deck, insert the middle

body (F) with the rubber washer (G), metal

washer (H) and mounting nut (I) through the

mounting hole.

□ From above, thread the connector (E) onto

the middle body (F).

□ Tighten the mounting nut (I) using a basin

wrench, so that the connector (E) sits ush

against the nished deck surface.

G

H

I

F

D

E

G

H

I

F

E

5

Installation (continued)

5

Removing the mounting kits

□ Remove the protective caps (P). Loosen the

anges (Q) from the valve bodys (R & S). Adjust

the rubber washers (T), metal washers (U) and

mounting nuts (V) to the bottom of valve

bodys (R & S).

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

6

Installing the valve bodies

□ From underneath the deck, insert the cold end

valve (S) with the rubber washer (T), metal

washer (U) and mounting nut (V) through

the hole on the right (cold) side.

□ From above, thread the ange (Q) onto the

valve body (S).

□ Tighten the mounting nut (V) using a basin

wrench, so that the ange (Q) sits ush against

the nished deck surface.

□ Repeat this procedure for the hot end valve (R)

on the left (hot) side.

NOTE: The hot end valve is identied with a label.

4

Installing the spout assembly

□ Install the spout assembly (A) onto the

connector (E). Be sure the spout assembly (A)

is resting rmly on the deck.

□ Push down on spout assembly (A) and tighten

set screw (B) with the Hex wrench

(Hex: 3.2mm, C).

A

B

C

E

P

Q

S

T

U

V

P

Q

R

T

U

V

R

S

T

U

V

Q

6

Installation (continued)

9

Making the water supply

connections

□ Connect the water supply lines (1) to the

faucet inlets (2). (Supply lines are not

included.)

8

Connecting the hoses

□ Connect the hoses (W) to the bottom of the hot

and cold end valves (R & S), as shown.

□ Align the middle body (F) in a position that will

allow maximum clearance to connect the

hoses (W).

□ Carefully bend the hoses (W) to t in the

available space, and carefully thread the hose

(W) couplings onto the sides of the middle

body (F). Tighten all connections with a wrench.

7

Installing the handle

□ Thread the connector (O) onto the valve stem (1).

Place the handle seat (M) onto the right (cold)

ange (Q) and the handle (J) onto the handle

seat (M). Place the set screw (N & K) into handle

seat (M) & handle (J) and tighten set screw

(N & K) with the Hex wrench (Hex: 2.5mm, L).

□ Place the other handle onto the left (hot) valve

and install the same way.

1

Q

J

K

L

M

N

O

L

F

W

R

S

1

2

7

Operation

1

Flushing and checking for leaks

□ Ensure the faucet handles are in the off position,

and turn on the water supply to check for leaks.

If you discover any leaks, check your connections

to ensure they are installed properly.

□ Turn on the hot and cold handles to allow the

water to run for at least one minute. This

ushes away any debris that could cause

damage to internal parts.

□ Turn off the water.

Care and Cleaning

□ To clean, wipe down with a damp cloth and dry with a towel.

□ Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will

be voided.

Troubleshooting

Problem Possible Cause Solution

There are leaks from the

handle.

The bonnet nut has come loose and/or the

washer is dirty or damaged.

□ Tighten the bonnet nut.

□ Clean or replace the washer.

The water will not shut off

completely.

The cartridge is dirty or broken. □ Remove the handle to check

the cartridge.

□ Clean or replace.

NOTE: Refer to the service parts section in this manual for

a detailed drawing showing the location of the parts listed

below.

There is a leak from the

spout base when the

faucet is on.

The o-ring which is on the connector

under the spout is worn.

□ Remove the spout and replace

a new o-ring.

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

8

Service Parts

*Specify Finish

Faucet ID tags can be

found by removing

the hot water handle

18 Metal washer RP64036

Part Description Part Number

Rubber washer RP64035

Part Description Part Number

16

17

O-ring RP60094

14

12

13

15

Mounting nut RP56014

Set screw RP50103

O-ring RP60056

Connector RP70459

Hose RP7033120

19 Mounting nut RP56088

Many replacement cartridges, aerators, and drain

assemblies can be purchased at your local The

Home Depot store or online at HOMEDEPOT.COM

1

RP13169*

2 Set screw RP50002

3

4

7

8

9

Handle seat RP17129*

Bonnet nut RP70001

11

Cartridge H

RP20067

Handle

Cartridge C RP20068

10

Rubber washer RP64023

Metal washer

RP64024

Wearable ring RP64053

5

6 Flange RP17051

Connector RP50106

1

2

3

5

2

4

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

Questions, problems, missing parts?

Before returning to the store, call Glacier Bay Customer Service

8 a.m. - 7 p.m., EST, Monday - Friday

9 a.m. - 6 p.m., EST, Saturday

1-855-HD-GLACIER (1-855-434-5224)

HOMEDEPOT.COM

Retain this manual for future use.

Page is loading ...

Glacier Bay HD461-8216 Installation guide

This manual is also suitable for

Glacier Bay HD461-8216 Installation guide

in other languages

Related papers

Other documents