Faber Inca Smart 21 Gray 240 Installation guide

Category
Cooker hoods
Type
Installation guide

This manual is also suitable for

2
READ AND SAVE THESE INSTRUCTIONS BEFORE YOU
START INSTALLING THIS RANGE HOOD
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils slowly on low or medium setting.
b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes
Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan
orlter.
d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnotheburner.
BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE
AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will
result.
d) Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. Thereissmallandcontainedintheareawhereitstarted.
3. Theredepartmentisbeingcalled.
4. Youcanghttherewithyourbacktoanexit.
* Based on "Kitchen Firesafety Tips" published by NFPA
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan
with any solid-state speed control device.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have any
questions, contact the manufacturer.
2. Beforeservicingorcleaningunit,switchpoweroatservicepanelandlockthe
service disconnecting means to prevent power from being switched on acciden-
tally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or
Explosive Materials and Vapors.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-
dance With All Applicable Codes And Standards, Including Fire-Rated Construction.
2. Sucientairisneededforpropercombustionandexhaustingofgasesthrough
theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe
heating equipment manufacturer's guideline and safety standards such as those
publishedbythe NationalFireProtectionAssociation(NFPA),andtheAmerican
SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and
the local code authorities.
3
3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities.
4. Ducted fans must always be vented to the outdoors.
ALL WALL AND FLOOR OPENINGS WHERE THE RANGE HOOD IS INSTALLED
MUST BE SEALED.
This Range Hood requires at least 24" of clearance between the bottom of the Range Hood
and the cooking surface or countertop. This hood has been approved by UL at this distance
from the cooktop.
This minimum clearance may be higher depending on local building codes. For gas cooktops
and combination ranges, a minimum of 30" is recommended and may be required.
Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface
or countertop. Consult the cooktop or range installation instructions given by the manufacturer
before making any cutouts.
MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the
Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly
Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See
Electrical Requirements.
• Venting system MUST terminate outside the home.
DO NOT terminate the ductwork in an attic or other enclosed space.
DO NOT use 4" laundry-type wall caps.
• Flexible-type ductwork is not recommended.
DO NOT obstruct the ow of combustion and ventilation air.
Failure to follow venting requirements may result in a re.
WARNING
!
VENTING REQUIREMENTS
Determine which venting method is best for your application. Ductwork can extend either through
the wall or the roof.
The length of the ductwork and the number of elbows should be kept to a minimum to provide ef-
cient performance. The size of the ductwork should be uniform. Do not install two elbows together.
Use duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor
opening around the cap.
Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence
that greatly reduces performance.
Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.
Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a support-
ing frame must be constructed.
WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.
CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do
not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.
Cold Weather installations
An additional back draft damper should be installed to minimize backward cold air ow and a nonmetal-
lic thermal break should be installed to minimize conduction of outside temperatures as part of the vent
system. The damper should be on the cold air side of the thermal break. The break should be as close
as possible to where the vent system enters the heated portion of the house.
4
• Electrical ground is required on this Range Hood.
• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO
NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or
grounding circuit could result in electrical shock.
• Check with a qualied electrician if you are in doubt as to whether the Range Hood is
properly grounded.
• Failure to follow electrical requirements may result in a re.
WARNING
!
StateofCaliforniaProposition65Warning(USonly)
WARNING
This product contains chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-de-
lay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance
with the electrical rating of this unit as specied on the serial/rating plate located inside the unit near
the eld wiring compartment.
6
MIN. 24" OVER ELECTRIC
INSTALLATION HEIGHT REQUIREMENTS
MIN. 30" OVER GAS
THE INCA SMART IS NOT DESIGNED FOR USE OVER PRO-STYLE
COOKING SURFACES, INSTALLATIONS OVER PRO-STYLE COOKING
SURFACES WILL COMPLETELY VOID THE WARRANTY OF THIS
PRODUCT .
WARNING
!
7
MAIN PARTS
Components
Ref. Qty. Product Components
1 1 Hood Body, complete with: Controls, Light, Filters,Blower.
8 1 Recirculation Vent Grill
10 1 Damper ø 5"
Ref. Qty. Installation Components
12a 10 Screws (for hood installation)
12b 4 Screws 1/8"x1/2" (for Cover installation)
12e 2 Screws 1/8"x3/8" (for Recirculation Vent Grill mounting)
Qty. Documentation
1 Instruction Manual

H
I

H
I

H
I

H
I
12b
10
12e
8
12a
12a Pozi Screws (1/8" x 5/8")
10
12b Pozi Screws (1/8" x 1/2")
4
12e Torx Screws (1/8" x 3/8")
2
Torx Screwdriver
Pozi Screwdriver
8
Available Accessories
Parts needed
- 5" Round Metal ductwork .
Liner 24" Stainless #LINE24ST
Liner 30" Stainless #LINE30ST
Liner 36" Stainless #LINE36ST
Activated Charcoal Filter sku #; FILTER4
Two men required for installation
Wear work gloves for safety
9
LINER DIMENSIONS
Version 09/14 - Page 4
SIDE VIEW / LA PERSPECTIVE DE CÔTÉ
FRONT VIEW / LA PERSPECTIVE DE FRONT
BOTTOM VIEW / LA PERSPECTIVE DE BAS
Standard Liner 36 Stainless (LINE36ST)
designed for 36” wide installations
Cadre Standard 36 Axier Inoxydable (LINE36ST)
peut être employée les hottes encastrable sur mesure de 36"
Standard Liner 30 Stainless (LINE30ST)
designed for 30” wide installations
Cadre Standard 30 Axier Inoxydable (LINE30ST)
peut être employée les hottes encastrable sur mesure de 30"
Note: Standard Liners are pre-cut for installation of Inca Smart. For installations with the Inca HC SS, remove the additional perforated section.
Note: Les Cadres Standard sont précoupés pour l'installation de l'Inca Smart. Pour des installations avec L'Inca HC SS, enlevez la section perforée
additionnelle.
RANGEHOOD DIMENSIONS / DIMENSIONS DE LA HOTTE
LINER DIMENSIONS / DIMENSIONS DU CADRE
Pre-Planning Your Installation -
Important: The recommended height to install this hood off the cooktop is
a minimum of 24" and a maximum of 30” for maximum effectiveness. Also consult the cooktop manufacturer’s
recommendation.
Planiez votre installation - Important : La hauteur recommandée pour installer cette hotte au-dessus de la
surface de cuisson est d’un minimum de 24” et d’un maximum de 30” pour un maximum d’efcacité. De plus,
nous vous recommandons consulter le manuel de recommandations du fabricant de la surface de cuisson.
NOTE: Remove the metal packaging support
piece from the top of the hood before
installation (SEE RIGHT)
NOTE : Enlevez le morceau de empaquetage de
soutien en métal du dessus du hotte avant
installation (VOYEZ BIEN)
Bellucci, Daniele
30-Jan-2019
Released
StandardLiner24Stainless(LINE24ST)designedfor24”wideinstallations
Pre-Planning your Installation - Important: The recommended height to install this hood o the
cooktop is a minimum of 24" and a maximum 30" for maximum eectiveness. Also consult the
cooktop manufacturer's recommendation.
StandardLiner30Stainless(LINE30ST)designedfor30”wideinstallations
StandardLiner36Stainless(LINE36ST)designedfor36”wideinstallations
10
FOR INSTALLATION WITH LINERS
When building a custom hood, always
follow all applicable codes and
standards.
WARNING
!
The Inca Smart can be used in
standard 24" or 30" or 36" wide
cabinetry or with custom hoods
30" wide and up.
For custom/wood hoods,
choose either YOUR OWN
custom liner or our Standard
Liner designed for 24"and 30"
and 36" wide installations.
Liners create a perfectly -
sealed, non-combustible
nish for the underside of your
custom/wood hood.
The Standard Liners are made
up of two sections: a larger,
rear section (pre-cut out for
insertion of the Inca Smart)
and a front section for a total
adjustable depth between 16"
and 17 7/8".
!!! IMPORTANT NOTE: DO NOT
REMOVE THE ADDITIONAL
PERFORATED SECTION AROUND
THE PRE-CUT-OUT WHEN
INSTALLING THE STANDARD
LINER WITH THE INCA SMART
MODEL.
Consider the shape, size,
and weight of the Inca Smart
and Liner to determine the
conguration of the custom/
wood hood.
See RANGEHOOD DIMENSIONS
AND LINER DIMENSIONS.
1. The custom/wood hood must have a sturdy base (3/4" plywood
recommended) to accomodate the cut-out for the Inca Smart. The base
must be recessed to accomodate the height of the Liner (see LINER
DIMENSIONS). The Liner attaches to the bottom of the base using
screws appropriate for the size and material of your custom/wood hood.
The Inca Smart inserts into the cut-out in the Liner and base.
2. Position the rear section of the Liner so that it abuts the back edge of
your custom/wood hood. Using a pen, trace the outline of the pre-cut out.
Remove the Liner and proceed to MAKE YOUR CUT-OUTS.
Install both sections of the Liner and proceed to INSTALL THE
RANGEHOOD.
Version 09/14 - Page 5
The Inca Smart requires 5" round ductwork. To ensure that the blower performs to its
highest possible capacity, ductwork should be as short and straight as possilbe.
Make your ductrun as straight and short as possible. The ductrun should not exceed 25
equivalent feet if ducted with the required minimum of 5" round duct. Count 45º angles
as 3 feet, 90º elbows as 5 feet, and 90º at elbows as 12 feet.
For best results, use no more than three 90° elbows. Make sure that there is a minimum
of 24" of straight duct between elbows if more than one is used. Do not install two
elbows together. If you must elbow right away, do it as far away from the hood's
exhaust opening as possible.
TOOLS NEEDED FOR INSTALLATION
• Saber Saw or Jig Saw
• Drill
• 1 1/4" Wood Drill Bit
• Pliers
• Phillips Screwdriver
• Wire Stripper or Utility Knife
• Metal Snips
• Measuring Tape or Ruler
• Level
• Pencil
• Caulking Gun
• Duct Tape
PLAN YOUR DUCTWORK
The Inca Smart can be used in
standard 30" or 36" wide cabinetry
or with custom hoods 30" wide
and up.
For custom/wood hoods, choose
either YOUR OWN custom liner or
our Standard Liner designed for 30"
and 36" wide installations. Liners
create a perfectly-sealed, non-
combustible nish for the underside
of your custom/wood hood.
The Standard Liners are made
up of two sections: a larger, rear
section (pre-cut out for insertion of
the Inca Smart) and a front section
for a total adjustable depth between
16" and 17
7/8".
!!! IMPORTANT NOTE: DO NOT
REMOVE THE ADDITIONAL
PERFORATED SECTION
AROUND THE PRE-CUT-
OUT WHEN INSTALLING
THE STANDARD LINER WITH
THE INCA SMART MODEL.
THIS PERFORATION IS ONLY
REMOVED FOR USE WITH THE
INCA HC SS MODEL.
Consider the shape, size, and
weight of the Inca Smart and Liner
to determine the configuration
of the custom/wood hood. See
RANGEHOOD DIMENSIONS AND
LINER DIMENSIONS on Page 4.
FOR INSTALLATIONS WITH LINERS
PARTS SUPPLIED FOR INSTALLATION
• 1 Backdraft Damper
• 10 Screws
• Field Wiring Box
• 1 Literature Package
PARTS NEEDED FOR INSTALLATION
• 2 Conduit Connectors
• Power Supply Cable
• Scews for Field Wiring Box
• 1 Wall or Roof Cap
• All Metal Ductwork
OPTIONAL ACCESSORIES AVAILABLE
Charcoal Filter Kit
For recirculating installations only,
replace charcoal lters as needed
part # FILTER4
Liners
Create a perfectly-sealed, non-combustible
perimeter around the Inca Smart. Depth adjustable
from 16" - 17
7/8"
.
Standard Liner 30 Stainless - part #
LINE30ST
Standard Liner 36 Stainless - part # LINE36ST
CUSTOM/WOOD
HOOD
STANDARD LINER
INCA SMART
WARNING
!
When building a custom hood,
always follow all applicable
codes and standards.
1. The custom/wood hood must have a sturdy base (3/4" plywood recommended) to accomodate
the cut-out for the Inca Smart. The base must be recessed to accomodate the height of the
Liner (see LINER DIMENSIONS on Page 4). The Liner attaches to the bottom of the base
using screws appropriate for the size and material of your custom/wood hood. The Inca Smart
inserts into the cut-out in the Liner and base.
2. Position the rear section of the Liner so that it abuts the back edge of your custom/wood
hood. Using a pen, trace the outline of the pre-cut out. Remove the Liner and proceed to MAKE
YOUR CUT-OUTS on Page 6. Install both sections of the Liner and proceed to INSTALL THE
RANGEHOOD on Page 6.
CUSTOM/WOODH
HOOD
STANDARD LINER
INCA SMART
11
Choose your ducting method
Requires purchase of Activated
Charcoal Accessory #Filter4
Rear
Top
5"
Non Ducted - RecirculationDucted Venting Installation
Remove the metal packaging
support piece from the top of the
hood before installation.
Caution: If an elbow is required,
do it as far away from the hood's
exhaust opening as possible.
12
INSTALL THE RANGE HOOD
1
2
Remove grease lters and set aside.
Remove the bottom of the Range Hood by pulling forward as shown.
13
3
The Hood can be installed directly on the underside of the cabinet (minimum 24" for electric ranges
and 30" for gas ranges).
Create an opening in the bottom of the Cabinet, as shown.
Attention: The cabinet must be accessible so that you can access the hood cable and
plug in the future, after installing the product.
1/2”
10 1/4”
19” 9/16 - 26” 5/8
1/2”
1/2”
10 1/4”
19” 9/16 - 26” 5/8
1/2”
1/2”
10 1/4”
19” 9/16 - 26” 5/8
1/2”
21"
28"
14
Insert the hood until the side supports snap into place.
Lock in position by tightening the screws Vf from underneath the hood.
Fasten using the 10 screws 12a provided.
10 1/2”
1/2”
19” 9/16 - 26” 5/8
Min.9/16"
Max 1" 3/16
Vf
Attention:
INSM21 uses 8 screws
INSM28/INSP uses 10 screws
4
5
15
Replace the bottom of the Range Hood by 4 screws 12b as shown.
Place the grease lters in the hood
6
7
12b
16
CHOOSE YOUR DUCTING METHOD
Ducted Venting Installation
8
Non Ducted -
Recirculation Option
Install Damper that is included with the
Hood before connecting to the ductwork.

H
I
Install Roof or Wall Cap purchased
separately. Connect the ø 5" metal duc-
twork to the Roof or Wall Cap and then
attach ductwork.


´
For Non-Ducted Recirculation venting,
route the ductwork to a location above the
hood where the discharge is vented back
into the room.
Use the included Recirculation Vent Grill to
cover the opening. Secure the grill with the
2 screws provided in the Install Kit.
Required Activated
Charcoal Filter Accessory
- sku # - FILTER4
4 15/16"
12e
8
Torx Screwdriver
17
9
ELECTRICAL INSTALLATION WITH CONNECTION CABLE
Max. 33 7/16
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of an electrical short circuit, grounding reduces the risk of electric shock
by providing an escape wire for the electric current.
This appliance is equipped with a cord having a grounding wire with a grounding plug.
The plug must be plugged into an outlet that is properly installed and grounded.
WARNING - Improper grounding can result in a risk of electric shock.
Consult a qualied electrician if the grounding instructions are not completely under-
stood, or if doubt exists as to whether the appliance is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have a qualied
electrician install an outlet near the appliance.
18
10
For Non-Ducted Recirculation Option
The charcoal lters must be
inserted behind the grease lters
as indicated.
Required Activated
Charcoal Filter Accessory -
sku # - FILTER4
19
USE AND CARE INFORMATION
For Best Results
Start the Range Hood several minutes before cooking to develop proper airow. Allow the
Range Hood to operate for several minutes after cooking is complete to clear all smoke and
odors from the kitchen.
INSM28GR240 INSM21GR240
Button Function
LED indicator light (L)
Light On/O Button
On/O switch for the lights.
Press the button to turn the light ON and press again to turn it OFF.
On/O
Move the switch to "1" to turn the blower ON and to "0" to turn the blower OFF.
Speed Control
1 Low Speed (ON)
2 Medium Speed
3 High Speed
20
For Best Results
Start the Range Hood several minutes before cooking to develop proper airow. Allow the
Range Hood to operate for several minutes after cooking is complete to clear all smoke and
odors from the kitchen.
Button Function
LED indicator light (L) - indicates current speed with color
Green - speed 1
Orange - speed 2
Red - speed 3
Flashing Red - intensive speed
Light On/O Button
On/O switch for the LED lights.
Press the button to turn the light ON and press again to turn it OFF.
Blower On/O Button
On/O button for the blower.
Press the button to turn the blower ON to speed one (indicated by green LED) and
press again to turn the hood o.
Blower Speed 2
Press this button to turn the hood onto speed #2. (indicated by orange LED).
Blower Speed 3 / Intensive
Press this button to turn the hood onto speed #3. (indicated by solid red LED)
Hold down the speed 3 button for 2 seconds to activate the intensive speed.
The intensive speed setting is indicated by a blinking red light.
This operates the hood for 10 minutes on the highest speed and then returns to the
previous speed.
INSP28SS240
USE AND CARE INFORMATION
21
Cleaningmetalgreaselters
The metal grease lters can be cleaned in hot detergent
solution or washed in the dishwasher. They should be
cleaned every 2 months use, or more frequently if use
is particularly heavy.
Remove the lter, pushing the lever towards the back
of the unit and at the same time pulling downward.
Wash the lter without bending it, leave it to dry
thoroughly before replacing (if the surface of the lter
changes color over time, this will have absolutely no
effect on its efciency).
Replace, taking care to ensure that the handle faces
forward.
Cleaning in dishwasher may dull the nish of the
metal grease lter.
No water can be present in lters before installing
back in hood.
Cleaning Exterior surfaces
Cleaning Exterior surfaces:
Please note, abrasives and scouring agents can scratch
range hood nishes and should not be used to clean
nished surfaces.
Stainless Steel nish cleaning instructions:
Clean exterior surfaces with a commercially available
stainless steel cleaner.
Painted Gray nish cleaning instructions:
Clean exterior surfaces with hot soapy water.
Replacing Activated Charcoal Filter
The Activated Charcoal Filters are not washable
and cannot be regenerated, and must be replaced
approximately every 4 months of operation, or more
frequently with heavy usage.
Remove the grease lters.
• Remove the saturated carbon lter.
Fit the new lter by hooking it into its seating.
Replace the grease lters.
Caution: When used in recirculation mode, to
Reduce the Risk of Fire and Shock use only
conversion kit Model FILTER 4.
22
Light Bulb Replacement
Remove grease lters and set aside.
Remove the bottom of the Range Hood by 4 screws 12b as shown.
Replace the lamp with a new one of the same type.
Replace the bottom of the Range Hood by 4 screws 12b.
Replace the grease lters.
E12 self-ballasted led lamps –
listed in accordance with ul 1993/
nmxj-578/1-ance/ csa c22.2 No.
1993
12b
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Faber Inca Smart 21 Gray 240 Installation guide

Category
Cooker hoods
Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI