Ryobi RYAC803-S Owner's manual

Brand: Ryobi

Model: RYAC803-S

Category: Snow throwers

Type: Owner's manual

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

20 in. SNOW BLOWER

SOUFFLEUSE À NEIGE DE 508 mm (20 po)

EQUIPO QUITANIEVE DE 508 mm (20 pulg.)

RYAC803

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

TABLE OF CONTENTS

 Important Safety Instructions .......... 2-3

 Symbols .......................................... 4-5

 Electrical .............................................6

 Features ..............................................7

 Assembly ........................................ 7-8

 Operation ...................................... 9-10

 Maintenance .....................................11

 Troubleshooting ................................12

 Parts Ordering/Service ........ Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation

avant d’employer ce produit.

TABLE DES MATIÈRES

 Instructions importantes

concernant la sécurité..................... 2-3

 Symboles ........................................ 4-5

 Caractéristiques électriques ...............6

 Caractéristiques ..................................7

 Assemblage .................................... 7-8

 Utilisation ...................................... 9-10

 Entretien ............................................11

 Dépannage ........................................ 12

 Commande de pièces /

réparation .......................... Páge arrière

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe

leer y comprender el manual del

operador antes de usar este producto.

ÍNDICE DE CONTENIDO

 Instrucciones de seguridad

importantes ..................................... 2-3

 Símbolos ......................................... 4-5

 Aspectos eléctricos ............................6

 Características ....................................7

 Armado ........................................... 7-8

 Funcionamiento ............................ 9-10

 Mantenimiento ..................................11

 Corrección de problemas .................12

 Pedidos de piezas/

servicio ........................... Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

Page is loading ...

2 — English

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below and on the

machine may result in electric shock, fire, and/or serious

personal injury.

Know your snow blower. Read operator’s manual care-

fully. Learn its applications and limitations, as well as the

specific potential hazards related to this snow blower.

Following this rule will reduce the risk of electric shock,

fire, or serious injury.

Do not permit children to use snow blower. It is not a

toy.

Use only accessories that are recommended by the

manufacturer for your model described in this manual.

Accessories that may be suitable for one snow blower

may create a risk of injury when used on another snow

blower. Use only as described in this manual.

 Do not put any object into openings. Do not use with any

opening blocked; keep free of dust, lint, hair, and anything

that may reduce air flow.

Keep hair, loose clothing, fingers, and all parts of body

away from openings and moving parts.

To reduce the risk of electric shock, this product has a

polarized plug (one blade is wider than the other) and will

require the use of a polarized extension cord. The plug

will fit into a polarized extension cord only one way. If the

plug does not fit fully into the extension cord, reverse the

plug. If the plug still does not fit, obtain a correct polarized

extension cord. A polarized extension cord will require

the use of a polarized wall outlet. This plug will fit into the

polarized wall outlet only one way. If the plug does not fit

fully into the wall outlet, reverse the plug. If the plug still

does not fit, contact a qualified electrician to install the

proper wall outlet. Do not change the equipment plug,

extension cord receptacle, or extension cord plug in any

way.

Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy

enough to carry the current your product will draw. A wire

gauge size (A.W.G.) of at least 14 is recommended for an

extension cord 25 feet or less in length. If in doubt, use

the next heavier gauge. The smaller the gauge number,

the heavier the cord. An undersized cord will cause a drop

in line voltage resulting in loss of power and overheating.

 WARNING: Use outdoor extension cords marked SW-A,

SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOW-

A. These cords are rated for outdoor use and reduce the

risk of electric shock.

Ground Fault Circuit Interrupter (GFCI) protection should

be provided on the circuit(s) or outlet(s) to be used for the

product. Receptacles are available having built-in GFCI

protection and may be used for this measure of safety.

This product is designed with a cord retainer that prevents

the extension cord from being pulled loose while using.

If cord is damaged in any manner while plugged in, pull

extension cord from wall receptacle.

Don’t Abuse Cord — Never carry snow blower by cord

or yank it to disconnect from receptacle. Keep cord from

heat, oil, and sharp edges.

Keep hands away from moving parts.

 Avoid Unintentional Starting – Do not carry plugged in

appliance with finger on trigger. Be sure the switch trigger

is not engaged before plugging in.

Do not use tool if switch trigger does not turn it on or off.

Any tool that cannot be controlled with the switch trigger

is dangerous and must be repaired.

Do not operate snow blowers in explosive atmospheres,

such as in the presence of flammable liquids, gases, or

dust. Snow blowers create sparks which may ignite the

dust or fumes.

Keep bystanders, children, and visitors at least 100 ft.

away while operating a snow blower. Distractions can

cause you to lose control.

 If appliance is not working as it should, has been dropped,

damaged, left outdoors, or dropped into water, return it

to a service center.

Stay alert, watch what you are doing and use common

sense when operating a power snow blower. Do not use

snow blower while tired, upset, or under the influence

of drugs, alcohol, or medication. A moment of inatten-

tion while operating snow blowers may result in serious

personal injury.

Use safety equipment. Always wear eye protection. Dust

mask, non-skid safety shoes, hard hat, or hearing protec-

tion must be used for appropriate conditions.

Dress properly — Do not wear loose clothing, scarves,

or jewelry. They can be caught in moving parts.

Check for misalignment or binding of moving parts,

breakage of parts, and any other condition that may af-

fect the snow blower’s operation. If damaged, have the

snow blower serviced before using. Many accidents are

caused by poorly maintained snow blowers.

Keep the snow blower and its handle dry, clean and free

from oil and grease. Always use a clean cloth when clean-

ing. Never use brake fluids, gasoline, petroleum-based

products, or any strong solvents to clean your snow

blower. Following this rule will reduce the risk of loss of

control and deterioration of the enclosure plastic.

Always wear safety glasses with side shields. Everyday

glasses have only impact resistant lenses. They are NOT

safety glasses. Following this rule will reduce the risk of

eye injury.

IMPORTANT SAFETY INSTRUCTIONS

3 — English

IMPORTANT SAFETY INSTRUCTIONS

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

Protect your hearing. Wear hearing protection during

extended periods of operation. Following this rule will

reduce the risk of serious personal injury.

Don’t expose snow blowers to rain. Water entering a snow

blower will increase the risk of electric shock.

Wear heavy long pants, long sleeves, boots, and gloves.

Avoid loose garments or jewelry that could get caught in

moving parts of the machine or its motor.

Wear rubber boots when operating the snow blower.

Protective footwear will protect your feet and improve

your footing on slippery surfaces. Do not go barefoot or

wear sandals.

Keep firm footing and balance. Do not overreach. Over-

reaching can result in loss of balance.

Do not operate the snow blower in a direction that will

cause snow to be thrown on people or pets. Thrown snow

or other objects can cause serious personal injuries.

Store Idle Snow Blowers Indoors — When not in use,

snow blower should be stored indoors in a dry, locked

up place — unplugged and out of the reach of children.

Keep all bystanders, children, and pets at least 100 ft.

away.

Snow blower service must be performed only by qualified

repair personnel. Service or maintenance performed by

unqualified personnel may result in a risk of injury.

When servicing a snow blower, use only identical replace-

ment parts. Replace or repair damaged cords. Follow

instructions in the Maintenance section of this manual.

Use of unauthorized parts or failure to follow Maintenance

instructions may create a risk of shock or injury.

Never use snow blower near fires, fireplaces, hot ashes,

bar becue pits, etc. Use near fires or ashes can spread

fires and result in serious injury and/or property damage.

Never use snow blower to spread chemicals, fertilizers, or

any other toxic substances. Spreading these substances

could result in serious injury to the operator or bystanders.

Never place snow blower on any surface, except a hard,

clean surface when motor is running. Gravel, sand, and

other debris can be picked up by the air inlet and thrown

at the operator or bystanders, causing possible serious

injuries.

Check the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which

can be thrown or become entangled in the machine.



Do not use snow blower on ice, which can cause the

operator to slip and fall, resulting in possible serious

personal injury.



Never use snow blower on frozen lakes, rivers, or similar

surfaces. Serious injury or death could occur if the ice

breaks.



Never use the snow blower on a rooftop or other unstable

surface, which can result in death or serious personal

injury.



For household use only.



Use the right appliance — Do not use the snow blower

for any job except that for which it is intended.



Do not force the snow blower — It will do the job better

and safer at the rate for which it was designed.



Never direct discharged material toward anyone. Avoid

discharging material against a wall or obstruction. Mate-

rial may ricochet back toward the operator. Stop the snow

blower when crossing gravel or rocky surfaces.



If the snow blower strikes a foreign object, follow these

steps:

• Release the switch trigger and wait until the unit comes

to a complete stop.

• Disconnect the snow blower from the power supply.

• Thoroughly inspect the snow blower for any damage.

• Repair any damage before restarting and continuing to

operate the snow blower.

 Do not lift up or hold the snow blower above the ground

when operating, which can result in loss of control and

possible serious personal injury. Only operate the snow

blower in accordance with the operating instructions

provided in this operator’s manual.



Keep guards in place and in working order.

Disconnect the plug from power source when not in use,

before servicing, and when changing accessories.



Maintain Snow Blowers With Care — Follow instructions

for lubricating and changing accessories.



Save these instructions. Refer to them frequently and use

them to instruct others who may use this tool. If you loan

someone this tool, loan them these instructions also.-

4 — English

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

Wet Conditions Alert Do not expose plug to water or rain.

Ricochet

Thrown objects can ricochet and result in personal injury or

property damage.

Keep Hands Out of Impeller Keep hands away from rotating impeller.

Keep Feet Out of Impeller Keep feet away from rotating impeller.

Keep Hands and Feet Away Keep hands and feet away from impeller and discharge chute.

Keep Children and

Bystanders Away

Keep all children and bystanders at least 100 ft. away.

Keep Hands and Feet Away Keep hands and feet away from rotating impeller.

5 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

No Slope

Do not operate on inclines greater than 15º. Walk across the face

of slopes, never up and down.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

No Load Speed Rotational speed, at no load

Class II Construction Double-insulated construction

.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute

SYMBOLS

6 — English

ELECTRICAL

EXTENSION CORDS

See Figure 1.

When using a power tool at a considerable distance from

a power source, be sure to use an extension cord that has

the capacity to handle the current the tool will draw. An

undersized cord will cause a drop in line voltage, resulting in

overheating and loss of power. Use the chart to determine

the minimum wire size required in an extension cord. Only

round jacketed cords listed by Underwriter’s Laboratories

(UL) should be used.

When working outdoors with a tool, use an extension cord

that is designed for outside use. This type of cord is desig-

nated with “WA” or “W” on the cord’s jacket.

Before using any extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

It is possible to tie the extension cord and power cord in a

knot to prevent them from becoming disconnected during

use. Make the knot as shown in figure 1, then connect the

plug end of the power cord into the receptacle end of the

extension cord. This method can also be used to tie two

extension cords together.

**Ampere rating (on tool data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25´ 16 16 16 16 14 14

50´ 16 16 16 14 14 12

100´ 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lumber,

tools, or other obstructions while you are working with

a power tool. Failure to do so can result in serious per-

sonal injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use tool with a damaged cord

since touching the damaged area could cause electrical

shock resulting in serious injury.

DOUBLE INSULATION

Double insulation is a concept in safety in electric power

tools, which eliminates the need for the usual three-

wire grounded power cord. All exposed metal parts are

isolated from the internal metal motor components with

protecting insulation. Double insulated tools do not need

to be grounded.

WARNING:

The double insulated system is intended to protect

the user from shock resulting from a break in the tool’s

internal insulation. Observe all normal safety precautions

to avoid electrical shock.

NOTE: Servicing of a tool with double insulation requires

extreme care and knowledge of the system and should be

performed only by a qualified service technician. For service,

we suggest you return the tool to your nearest authorized

service center for repair. Always use original factory replace-

ment parts when servicing.

ELECTRICAL CONNECTION

This tool has a precision-built electric motor. It should be

connected to a power supply that is nominal 120V/60Hz

AC (typical U.S. household circuit). Do not operate this

tool on direct current (DC). A substantial voltage drop will

cause a loss of power and the motor will overheat. If your

tool does not operate when plugged into an outlet, double-

check the power supply.

GFCI

Ground Fault Circuit Interrupter (GFCI) protection should

be provided on the circuit(s) or outlet(s) to be used for the

snow shovel. Receptacles are available having built-in GFCI

protection and may be used for this measure of safety.

7 — English

PRODUCT SPECIFICATIONS

Input ...........................................................................................................................nominal 120V/60Hz AC only, 13 Amps

Clearing Width ................................................................................................................................................................ 20 in.

Clearing Depth ............................................................................................................................................................... 10 in.

FEATURES

KNOW YOUR SNOW BLOWER

See Figure 2.

The safe use of this product requires an understanding of the

information on the product and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

CHUTE DEFLECTOR HANDLE

The chute deflector handle allows you to change the distance

that snow will discharge from the chute.

CHUTE ROTATION LEVER

The chute rotation lever allows you to choose the direction

that snow will discharge from the snow blower. The lever

allows the chute to rotate up to 180º.

CORD RETAINER

The cord retainer helps prevent accidental unplugging of

the extension cord.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Snow Blower

Upper and Intermediate Handles

Handle Mounting Hardware

Chute Deflector

Chute Rotation Lever Upper and Lower Rods with Hitch Pin

Cord Retainer

Operator’s Manual

WARNING:

If any parts are damaged or missing, do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this product.

Any such alteration or modification is misuse and could

result in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not connect to power supply until assembly is com-

plete. Failure to comply could result in accidental starting

and possible serious personal injury.

8 — English

INSTALLING INTERMEDIATE HANDLE

See Figure 3.

 Slide the cord retainer over the lower handle and position

in the center top portion of the handle.

 Align the holes on the intermediate handle with the holes

in the lower handle as shown.

 Insert J-bolt through both handles with the threaded end

at the top and facing inside.

 Install the handle knob and tighten securely to secure the

bolt in place.

 Repeat on the opposite side to secure the intermediate

handle in place.

INSTALLING UPPER HANDLE

See Figure 3.

 Align the hole on the upper handle with the hole in the

intermediate handle as shown.

NOTICE:

Do not allow the starter cable to become pinched or

trapped when aligning the handles.

 Insert bolt through both handles with the threaded end

facing inside.

 Install the handle knob and tighten to secure.

 Repeat on the opposite side.

ASSEMBLY

INSTALLING CHUTE DEFLECTOR

See Figure 4.

 Spread the sides of the chute deflector slightly and posi-

tion over the top of the chute.

 Shift the position of the deflector as needed so the tabs

and posts on the chute are fully seated into the openings

on the deflector as shown.

INSTALLING CHUTE ROTATION LEVER

See Figure 5.

NOTE: The lever bracket and opening on the back of the

snow blower housing are keyed to match the end of the chute

rotation lever bottom rod. Make sure to orient the rod in the

same direction as the keyed holes when installing the lever.

 Slide the end of the chute rotation lever bottom rod

through the bracket on the intermediate handle.

 Insert the rod into the hole in the snow blower housing

until it is fully seated.

 Install the upper rod of the chute rotation lever over the

lower end of the lever. Align the holes in the two parts

of the lever and insert the hitch pin through the holes as

shown to secure.

 Turn the lever left and right to verify the proper functioning

of the lever and the chute.

9 — English

WARNING:

Do not allow familiarity with products to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please contact customer service or an

authorized service center for assistance.

APPLICATIONS

You may use this product for the purpose listed below:

Removing snow from desired areas such as driveways

and sidewalks

WARNING:

Always disconnect snow blower from power supply when

you are assembling parts, making adjustments, cleaning,

or when not in use. This will prevent accidental starting

that could cause serious personal injury.

CONNECTING TO POWER SUPPLY

See Figure 6.

This product is designed with a cord retainer that prevents

the extension cord from being pulled loose while using.

Form a loop with the end of the extension cord.

Insert loop portion of extension cord through opening

and place over cord retainer.

Slowly pull loop against cord retainer until the slack is

removed.

Plug product into extension cord.

NOTE: Failure to remove all excess cord slack from cord

retainer could result in plug loosening from receptacle.

OPERATION

STARTING/STOPPING THE SNOW BLOWER

See Figure 7.

Connect the snow blower to power supply.

NOTICE:

Always secure extension cord to unit by using cord

retainer. Failure to use cord retainer may result in damage

to the unit and/or extension cord.

Press and hold the start button. Pull the bail toward the

handle and release the start button to start the snow

blower.

To stop the unit, release the bail.

ADJUSTING THE CHUTE

See Figures 8 - 9.

The chute can be adjusted to change both the direction and

the distance to assist you in moving snow away from one

area and placing it in another.

The direction of snow removal can be adjusted up to 180º.

Turn the chute rotation lever to the left to rotate the chute

to the left.

Turn the chute rotation lever to the right to rotate the

chute to the right.

The distance the snow is moved is adjusted using the chute

deflector handle. Squeeze the two parts of the chute deflec-

tor handle together to adjust.

Move the chute deflector forward (up) to increase the

distance the snow will be thrown.

WARNING:

Do not force the chute so far forward that a gap appears

between the deflector and the chute itself. Snow or other

debris could be thrown through the gap back at the

operator, resulting in serious personal injury.

Move the chute deflector backward (down) to decrease

the distance the snow will be thrown.

OPERATING TIPS

WARNING:

Never use snow blower on frozen lakes, rivers, or similar

surfaces. Death or serious injury could occur if the ice

breaks.

WARNING:

Never use the snow blower on a rooftop or other unstable

surface, which can result in death or serious personal

injury.

10 — English

OPERATION

WARNING:

Do not use snow blower on ice, which can cause the

operator to slip and fall, resulting in possible serious

personal injury.

WARNING:

Do not wear loose clothing, scarves, or jewelry. They can

be caught in moving parts and cause death or serious

personal injury.

WARNING:

Keep all snow discharge pointed away from all electri-

cal devices to reduce the risk of electrocution or electric

shock.

WARNING:

Never point the snow blower or discharge chute in the

direction of people or pets. Thrown snow or other objects

can cause serious personal injuries.

WARNING:

Make sure the area to be cleared is free of stones, sticks,

wires, gravel, and other objects that could be accidentally

thrown by the snow blower in any direction and cause

serious personal injury to the operator and others.

Take notice of the direction of the wind before beginning.

When possible, discharge snow in the same direction as

the wind to prevent snow from being thrown back into

your face.

If the unit comes in contact with any type of obstruction

or debris during use, stop the snow blower, disconnect

from the power supply, remove the obstruction, and

inspect the unit carefully for damage before proceeding.

WARNING:

Never reach into the impeller or place any body part in

front of the snow blower when the unit is operating or

when the unit is plugged in. Always ensure all moving

parts have stopped and the snow blower has been un-

pugged before clearing any obstructions. Failure to follow

these instructions can result in serious personal injury.

Some parts of the snow blower can freeze under extreme

weather conditions. Do not attempt to operate the unit

with frozen parts.

When finished, allow the motor to run for an additional

few minutes, then turn the chute rotation lever back and

forth several times to remove any remaining snow from

the chute.

11 — English

WARNING:

Before inspecting, cleaning or servicing the unit, stop the

motor, wait for all moving parts to stop, and disconnect

from power supply. Failure to follow these instructions

can result in serious personal injury or property damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

When servicing, use only authorized replacement parts.

Use of any other parts can create a hazard or cause

product damage.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please contact customer service or an

authorized service center for assistance.

MAINTENANCE

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken, or

destroy plastic which can result in serious personal injury.

LUBRICATION

All of the bearings in this product are lubricated with a

sufficient amount of high grade lubricant for the life of the

unit under normal operating conditions. Therefore, no further

bearing lubrication is required.

STORING THE SNOW BLOWER

CAUTION:

Ensure all melted snow that may drip from the snow blow-

er is properly wiped up to prevent a slip and fall hazard.

Wipe the snow blower with a clean dry cloth.

Check all nuts, bolts, knobs, screws, fasteners, etc., for

tightness.

Inspect moving parts for damage, breakage, and wear.

Have repairs made on any damaged or missing parts.

Loosen the handle knobs and lower the upper handle

assembly.

Store snow blower indoors in a clean, dry place out of

the reach of children.

Do not store near corrosive materials such as fertilizer or

rock salt.

12 — English

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM POSSIBLE CAUSE SOLUTION

Snow blower not starting. Snow blower is unplugged.

Start button is not depressed.

Connect snow blower to power supply.

Press start button.

The motor is on but the impeller does

not turn.

The drive belt is worn or broken. Have the drive belt replaced by an au-

thorized service center.

After passing, the snow blower leaves

a layer of snow on the ground.

The impeller/scraper mechanism is

worn.

Have the impeller/scraper mechanism

replaced by an authorized service

center.

MAKE THE MOST OF YOUR PURCHASE!

Go to http://register.ryobitools.com and register your new tool on-line.

Your product has been fully tested prior to shipment

to ensure your complete satisfaction.

For any questions about operating or maintaining

your product, call the Ryobi

Help Line!

This product has a Five-year Limited Warranty for personal,

family, or household use (90 days for business or commercial use).

For warranty details, visit www.ryobitools.com

or call (toll free) 1-800-860-4050.

Page is loading ...

Ryobi RYAC803-S Owner's manual

Brand: Ryobi

Model: RYAC803-S

Category: Snow throwers

Type: Owner's manual

Download PDF

report

in other languages

français: Ryobi RYAC803-S Le manuel du propriétaire
español: Ryobi RYAC803-S El manual del propietario

Ryobi RYAC803-S Owner's manual

Ryobi RYAC803-S Owner's manual

in other languages

Related papers

Other documents