Designed specifically for 42PV30A
TY-42PV30NZ
BUS4804
IMPORTANT: DO NOT PUSH OR PULL THE TV TO MOVE THE CABINET.
Please follow these assembly instructions.
Left Location Pin
Right Location Pin
Packer
Back side
Moulding
Cable Pin
IMPORTANT:- MISSING PARTS CANNOT BE REP LA CED UNLESS THE INFORMATION REQUESTED ABOVE IS FULLY SUPPLIED.
1. MODEL NUMBER OF THE UNIT PURCHASED
6. SERIAL NUMBER OF THE UNIT PURCHASED
OR CALL YO UR CLOSEST SERVICE CE NTRE, PROVIDING THE DETAILS BELOW.
FOR MIS SI NG OR FAUL TY PARTS: PLEA SE RECHECK YOUR PACKAGING TO ENSURE THAT PARTS ARE MISSING, THEN WRITE
3. DESCRIPTION O F THE MISSING PART
2. COPY OF YOUR PURCHASE SLIP
5. QUANTITY OF THE PARTS MISSING
4. PART NUMBER OF THE MISSING PART
www.criterionfurniture.com
(LOCATED ON UNDERSIDE OF TOP OF UNIT)
POST DETAILS AS REQUESTED IN 1-6 INCLUSIVE TO:-
MAKE SURE YOU INCLUDE YOUR ADDRESS,
NEW ZEALAND - CALL 0800 CRITERION (0800 274-837) OR FAX 0800 119-444.
CRITERION FURNITURE (NZ) LTD,
AUCKLAND 1730,
NEW ZEALAND.
P.O. BOX 58-646,
GREENMOUNT,
AUSTRALIA - A FTER SALES SERVICES: CALL - 02 9453 9555
Customer Service
M19721A1PO
M19722A1PO
M19723A1PO
M19591B2PO
M19595A2PO
M19592A1DF
M19619B1DF
M19596A1PO
M19597A1PO
PG0303A0
P815056
P816177
P816178A
P816179A
P816172
MH1101A0
1
1
1
2
2
2
2
2
2
2
5
2
1
1
2
1
Top
Packer
Base
Front Rail
Front Mouldings
Back Side Mou ldings
Side Mouldings
Left Glass Bracket
Right Glass Bracket
Glass Shelf
Castor
Cable Holder
Right Location Pin
Left Location Pin
Threaded Rod
Hardware Pack
Part Number
Quantity
Unpack & Iden tify P arts
CARTON CONTENTS
Part Description
Front Rail
Castor
Base
Glass shelf
Front
Moulding
Right
Glass Bracket
Side Moulding
Cable holder
Left
Glass Bracket
Top
STEP 1
1.Fasten5CastorstotheBaseasshown.
2. Insert Wooden Do wels as shown above.
x10
P800201 x 16
Base (underside)
Castor
P860045
Allen key
STEP 5
1. Fit Sleeve Nut at one end of each Threaded Rod using an Allen Key.
2. Insert Threaded Rod into Assembly through Base as shown.
3. Fit another Slee ve Nut at other end of Threade d Rod from Top and tighten it turning both Allen Keys in opposite
direction of e ach other.
Threaded Rod
P816172 x 2
Sleeve Nut
P860256 x 4
Allen key
Allen key
Threaded
Rod
STEP 6
1. Fit 2 S m all Connecting Rods to each Front Rail as shown.
2. Fit Front Mouldings to Ba s e as shown.
3. Fit Front Rails on to Front Mouldings as shown.
Front
Rail
Fron t Rail
Front Rail
Front
Moulding
STEP 7
1. Fasten the Front Rails an d Front Mouldings to the Base while holding them flush with outside e dge of Stand using 2
Locking Screws.
View from front o f Stand
Fron t Rail
Fron t Rail
Front
Moulding
Front
Moulding
Ensure that Front R ail, Front Moulding and
Base are all flush on outside edge.
1. Tighten the 4 pre-fitted Cams in Top, by turning them clockwise.
STEP 8
STEP 9
1. Fasten the Glass Brackets to Side Mouldings using Screws as shown.
Right Glas s Bracket x 2
Left Glass Bracket x 2
P860246 x 8
STEP 10
1. Slide each Glass Shelf into Glass Brackets and tighten Grub S crews from the underside of brackets as shown, make
sure the Back Edge of Glass Shelf is flush with Glass Bracket.
The curved part of the Glass sh ould be at the front.
STEP 14
2. While Gently pushing t he Plasma TV back to ensure the TV is standing straight on the stand, tighten the TV with the Bolts as
shown below.
1. With help of an Assistant , lift the Television on to Pins e nsuring t hat the P ins line up with the Holes in base of Television.
Ensure TV is standing straight
on the stand before you tighten
the bolts.
Once Cables are behind Pins,
slide the Cable Pins across into
the Side Moulding.
CABLE MANAGEMENT
Bac k Side Moulding
Side Moulding
1. With Cable Pins pushed into Back Side M ouldings, place Cables behind pins, t hen slide Pins across into the Side Mouldings.
Congratulations you ha ve now finished the assembly for your Panasonic Television Stand.
/