Grizzly G0514 User manual

Grizzly
Brand
Grizzly
Model
G0514
Type
User manual

This manual is also suitable for

MODEL G0513/G0514
17" & 19" HEAVY DUTY
BANDSAWS
OWNER'S MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

G0513 G0514
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
3OMEDUSTCREATEDBYPOWERSANDINGSAWINGGRINDINGDRILLINGAND
OTHERCONSTRUCTIONACTIVITIESCONTAINSCHEMICALSKNOWNTOTHE3TATE
OF#ALIFORNIATOCAUSECANCERBIRTHDEFECTSOROTHERREPRODUCTIVE
HARM3OMEEXAMPLESOFTHESECHEMICALSARE
s ,EADFROMLEADBASEDPAINTS
s #RYSTALLINESILICAFROMBRICKSCEMENTANDOTHERMASONRYPRODUCTS
s !RSENICANDCHROMIUMFROMCHEMICALLYTREATEDLUMBER
9OURRISKFROMTHESEEXPOSURESVARIESDEPENDINGONHOWOFTENYOU
DOTHISTYPEOFWORK4OREDUCEYOUREXPOSURETOTHESECHEMICALS
7ORKINAWELLVENTILATEDAREAANDWORKWITHAPPROVEDSAFETYEQUIP
MENTSUCHASTHOSEDUSTMASKSTHATARESPECIALLYDESIGNEDTOFILTER
OUTMICROSCOPICPARTICLES
Table of Contents
INTRODUCTION ............................................... 2






SECTION 1: SAFETY ....................................... 9

 
SECTION 2: CIRCUIT REQUIREMENTS ...... 12
SECTION 3: SETUP ....................................... 13
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
SECTION 4: OPERATIONS ........................... 27
 
 
 
 
 
 
 
 
 
 
 
 
 
SECTION 5: ACCESSORIES ......................... 36
SECTION 6: MAINTENANCE ......................... 38
 
 
 
 
 
SECTION 7: SERVICE ................................... 40
 
 
 
 
 
 
 
 
 
 
SECTION 8: WIRING ...................................... 53
 
 
SECTION 9: PARTS ....................................... 55
 
 
 
 
 
WARRANTY AND RETURNS ........................ 64


INTRODUCTION

















Contact InfoManual Accuracy

       


      

 
your machine may not exactly match the
manual

        



        
      



www.grizzly.com
       



        


     
        

       

       

     
       

Machine Description


Figure 1. 
A. 
B. 
C. 
D. 
E. 
F. 
G. 
H. 
I. 
J. 
Identification
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before beginning
any operations.
Figure 2.
K. 
L. 
M. 
Figure 3.
N. 
O. 
P. 
Q. 


Wheel Brush

    Figure 6   


Blade Tension Scale

     Figure 4   

        
        

Figure 6.


Figure 4.



Tension Lever Adjustment Screw
     Figure 5




Figure 5.



The information contained herein is deemed accurate as of 11/1/2010 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 2Model G0513
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0513 17" BANDSAW - 2 HP
Product Dimensions:
Weight.............................................................................................................................................................. 266 lbs.
Length/Width/Height............................................................................................................................. 32 x 32 x 73 in.
Foot Print (Length/Width)....................................................................................................................... 27 x 17-3/4 in.
Shipping Dimensions:
Type....................................................................................................................................................Wood Slat Crate
Content............................................................................................................................................................ Machine
Weight.............................................................................................................................................................. 342 lbs.
Length/Width/Height............................................................................................................................. 20 x 30 x 81 in.
Electrical:
Power Requirement..............................................................................................110V or 220V, Single-Phase, 60 Hz
Minimum Circuit Size............................................................................................ 30 amps at 110V, 15 amps at 220V
Switch............................................................................................................................................ On/Off Push Button
Switch Voltage............................................................................................................................................... 110/220V
Cord Length............................................................................................................................................................ 6 ft.
Cord Gauge....................................................................................................................................................14 gauge
Plug Included............................................................................................................................................................No
Recommended Plug/Outlet Type.....................................................................................L5-30 at 110V, 6-15 at 220V
Motors:
Main
Type.................................................................................................................. TEFC Capacitor Start Induction
Horsepower.................................................................................................................................................2 HP
Voltage.................................................................................................................................................110/220V
Prewired......................................................................................................................................................220V
Phase........................................................................................................................................................ Single
Amps........................................................................................................................................................20/10A
Speed.................................................................................................................................................1725 RPM
Cycle..........................................................................................................................................................60 Hz
Number Of Speeds........................................................................................................................................... 1
Power Transfer ................................................................................................................................... Belt Drive
Bearings.................................................................................................. Shielded and Permanently Lubricated
Main Specifications:
Operation
Blade Speeds........................................................................................................................... 1700, 3500 FPM
Table Tilt........................................................................................................................... Left 10, Right 45 deg.
Cutting Capacities
Maximum Cutting Height......................................................................................................................12-1/8 in.
Max Capacity Under Handwheel................................................................................................................12 in.
Max Capacity Left of Blade.................................................................................................................. 16-1/4 in.


The information contained herein is deemed accurate as of 11/1/2010 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 2Model G0513
Blade Information
Standard Blade Length...................................................................................................................... 131-1/2 in.
Blade Width Range.............................................................................................................................. 1/8 - 1 in.
Upper Blade Guides...................................................................................................... Roller Disc/Ball Bearing
Lower Blade Guides...................................................................................................... Roller Disc/Ball Bearing
Guide Post Size....................................................................................................................... 1.180 in. (30mm)
Guide Post Type....................................................................................... Sq. Tubing, 0.075 in. Wall Thickness
Table Information
Table Length.............................................................................................................................................. 17 in.
Table Width................................................................................................................................................ 17 in.
Table Thickness..................................................................................................................................... 1-1/2 in.
Floor to Table Height............................................................................................................................37-1/2 in.
Fence Information
Locks in Front............................................................................................................................................... Yes
Locks in Rear..................................................................................................................................................No
Adjustable for Blade Lead.............................................................................................................................Yes
Construction
Table Construction...................................................................................................Precision Ground Cast Iron
Rip Fence ............................................................................................................... Deluxe Extruded Aluminum
Base Construction......................................................................................................................... Formed Steel
Body Construction......................................................................................................................... Formed Steel
Upper Wheel.............................................................................................. Computer Balanced Cast Aluminum
Lower Wheel.............................................................................................. Computer Balanced Cast Aluminum
Tire Material................................................................................................................................... Polyurethane
Wheel Cover .......................................................................................................................... Pre-Formed Steel
Paint.......................................................................................................................................................... Epoxy
Other Related Information
Wheel Diameter................................................................................................................................... 16-3/4 in.
Wheel Width...........................................................................................................................................1-1/4 in.
Number of Dust Ports........................................................................................................................................2
Dust Port Size.............................................................................................................................................. 4 in.
Mobile Base........................................................................................................................................... G7314Z
Other Specifications:
ISO Factory ...................................................................................................................................................ISO 9001
Country Of Origin ..............................................................................................................................................Taiwan
Warranty ............................................................................................................................................................ 1 Year
Serial Number Location ................................................................................................................ Label on Top Cover
Awards .....................................................................................................................Wood Magazine Top Value 2005
Assembly Time ........................................................................................................................................... 30 minutes
Features:
European Style Roller Disc Blade Guides with Full Enclosure Protection and Ball Bearing Design
Quick Change Blade Release/Tensioner
Magnifying Window Over Fence Scale
Micro Adjusting Geared Table
Height Scale Measurement
Blade Tracking Window
Two 4" Dust Ports
Hinged Wheel Covers


The information contained herein is deemed accurate as of 11/1/2010 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 2Model G0514
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0514 19" HEAVY-DUTY BANDSAW - 2 HP
Product Dimensions:
Weight.............................................................................................................................................................. 319 lbs.
Length/Width/Height............................................................................................................................. 36 x 32 x 78 in.
Foot Print (Length/Width)................................................................................................................. 29-1/2 x 17-3/4 in.
Shipping Dimensions:
Type....................................................................................................................................................Wood Slat Crate
Content............................................................................................................................................................ Machine
Weight.............................................................................................................................................................. 385 lbs.
Length/Width/Height............................................................................................................................. 21 x 33 x 84 in.
Electrical:
Minimum Circuit Size...........................................................................................30 amps @ 110V, 15 amps @ 220V
Switch........................................................................................................................................................ Push Button
Switch Voltage............................................................................................................................................... 110/220V
Cord Length............................................................................................................................................................ 6 ft.
Cord Gauge....................................................................................................................................................14 gauge
Plug Included............................................................................................................................................................No
Recommended Plug/Outlet Type.......................................................................................L5-30 @110V, 6-15@220V
Motors:
Main
Type.................................................................................................................. TEFC Capacitor Start Induction
Horsepower.................................................................................................................................................2 HP
Voltage.................................................................................................................................................110/220V
Prewired......................................................................................................................................................220V
Phase........................................................................................................................................................ Single
Amps........................................................................................................................................................20/10A
Speed.................................................................................................................................................1725 RPM
Cycle..........................................................................................................................................................60 Hz
Number Of Speeds........................................................................................................................................... 1
Power Transfer ................................................................................................................................... Belt Drive
Bearings.................................................................................................. Shielded and Permanently Lubricated
Main Specifications:
Operation
Blade Speeds........................................................................................................................... 1700, 3500 FPM
Table Tilt........................................................................................................................... Left 10, Right 45 deg.
Cutting Capacities
Maximum Cutting Height......................................................................................................................12-1/4 in.
Max Capacity Under Handwheel................................................................................................................12 in.
Max Capacity Left of Blade.................................................................................................................. 18-1/4 in.


The information contained herein is deemed accurate as of 11/1/2010 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 2Model G0514
Blade Information
Standard Blade Length.............................................................................................................................143 in.
Blade Width Range........................................................................................................................ 1/8 - 1-1/4 in.
Upper Blade Guides...................................................................................................... Roller Disc/Ball Bearing
Lower Blade Guides...................................................................................................... Roller Disc/Ball Bearing
Guide Post Size....................................................................................................................... 1.180 in. (30mm)
Guide Post Type....................................................................................... Sq. Tubing, 0.075 in. Wall Thickness
Table Information
Table Length.............................................................................................................................................. 19 in.
Table Width................................................................................................................................................ 19 in.
Table Thickness..................................................................................................................................... 1-1/2 in.
Floor to Table Height............................................................................................................................37-1/2 in.
Fence Information
Locks in Front............................................................................................................................................... Yes
Locks in Rear..................................................................................................................................................No
Adjustable for Blade Lead.............................................................................................................................Yes
Construction
Table Construction...................................................................................................Precision Ground Cast Iron
Rip Fence ............................................................................................................... Deluxe Extruded Aluminum
Base Construction......................................................................................................................... Formed Steel
Body Construction......................................................................................................................... Formed Steel
Upper Wheel.............................................................................................. Computer Balanced Cast Aluminum
Lower Wheel.............................................................................................. Computer Balanced Cast Aluminum
Tire Material................................................................................................................................... Polyurethane
Wheel Cover .......................................................................................................................... Pre-Formed Steel
Paint.......................................................................................................................................................... Epoxy
Other Related Information
Wheel Diameter................................................................................................................................... 18-7/8 in.
Wheel Width...........................................................................................................................................1-1/4 in.
Number of Dust Ports........................................................................................................................................2
Dust Port Size.............................................................................................................................................. 4 in.
Other Specifications:
ISO Factory ...................................................................................................................................................ISO 9001
Country Of Origin ..............................................................................................................................................Taiwan
Warranty ............................................................................................................................................................ 1 Year
Serial Number Location ................................................................................................................ Label on Top Cover
Assembly Time ........................................................................................................................................... 45 minutes
Features:
Miter Gauge
Quick Change Blade Release/Tensioner
Blade Tension Indicator
Rack and Pinion Adjustable Upper Guide
Magnifying Window Over Fence Scale
Micro Adjusting Geared Table
Height Scale Measurement
Hinged Wheel Covers


Safety Instructions for Machinery
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance
of the safety messages. The progression of symbols is described below. Remember that safety
messages by themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
WEARING PROPER APPAREL. 9d cdi lZVg
Xadi]^c\! VeeVgZa! dg _ZlZagn i]Vi XVc WZXdbZ
ZciVc\aZY ^c bdk^c\ eVgih# 6alVnh i^Z WVX` dg
XdkZgadc\]V^g# LZVgcdc"ha^e[ddilZVgidVkd^Y
VXX^YZciVa ha^eh l]^X] XdjaY XVjhZ V adhh d[
ldg`e^ZXZXdcigda#
HEARING PROTECTION. 6alVnh lZVg ]ZVg"
^c\egdiZXi^dcl]Zc deZgVi^c\dgdWhZgk^^c\adjY
bVX]^cZgn# :miZcYZY ZmedhjgZ id i]^h cd^hZ
l^i]dji]ZVg^c\egdiZXi^dcXVc XVjhZ eZgbVcZci
]ZVg^c\adhh#
MENTAL ALERTNESS. 7Z bZciVaan VaZgi l]Zc
gjcc^c\ bVX]^cZgn# CZkZg deZgViZ jcYZg i]Z
^c[ajZcXZd[Ygj\hdgVaXd]da!l]Zci^gZY!dgl]Zc
Y^higVXiZY#
OWNER’S MANUAL. GZVY VcY jcYZghiVcY
i]^hdlcZg»h bVcjVa 7:;DG: jh^c\bVX]^cZ#
JcigV^cZYjhZghXVcWZhZg^djhan]jgi#
EYE PROTECTION. 6alVnh lZVg 6CH>"
VeegdkZYhV[Zin\aVhhZhdgV[VXZh]^ZaYl]Zc
deZgVi^c\ dg dWhZgk^c\ bVX]^cZgn# id gZYjXZ
i]Z g^h` d[ ZnZ ^c_jgn dg Wa^cYcZhh [gdb [an"
^c\ eVgi^XaZh :kZgnYVn ZnZ\aVhhZh VgZ cdi
VeegdkZYhV[Zin\aVhhZh#
HAZARDOUS DUST. 9jhiXgZViZYl]^aZjh^c\
bVX]^cZgn bVn XVjhZ XVcXZg! W^gi] YZ[ZXih!
dgadc\"iZgbgZhe^gVidgnYVbV\Z#7Z VlVgZ d[
Yjhi ]VoVgYh VhhdX^ViZY l^i] ZVX] ldg`e^ZXZ
bViZg^Va!VcYValVnhlZVgVC>DH="VeegdkZY
gZhe^gVidgidgZYjXZndjgg^h`#
Safety Instructions for Machinery
SECTION 1: SAFETY


DISCONNECTING POWER SUPPLY. 6alVnh
Y^hXdccZXi bVX]^cZ [gdb edlZg hjeean WZ[dgZ
hZgk^X^c\! VY_jhi^c\! dg X]Vc\^c\ Xjii^c\ iddah
W^ih!WaVYZh!XjiiZgh! ZiX##BV`ZhjgZhl^iX]^h
^cD;;edh^i^dcWZ[dgZgZXdccZXi^c\idVkd^YVc
jcZmeZXiZYdgjc^ciZci^dcVahiVgi#
INTENDED USE.DcanjhZi]ZbVX]^cZ[dg^ih
^ciZcYZYejgedhZVcYdcanjhZgZXdbbZcYZY
VXXZhhdg^Zh#CZkZghiVcYdcbVX]^cZ!bdY^[n
^i [dg Vc VaiZgcVi^kZ jhZ! dg dji[^i ^i l^i] cdc"
VeegdkZYVXXZhhdg^Zh#
STABLE MACHINE. JcZmeZXiZY bdkZbZci
Yjg^c\deZgVi^dch\gZVian^cXgZVhZhi]Z g^h` d[
^c_jgnVcYadhhd[Xdcigda#KZg^[nbVX]^cZhVgZ
hiVWaZ$hZXjgZ VcY bdW^aZ WVhZh ^[ jhZY VgZ
adX`ZYWZ[dgZhiVgi^c\#
FORCING MACHINERY.9dcdi[dgXZbVX]^cZ#
>il^aaYdi]Z_dWhV[ZgVcYWZiiZgVii]ZgViZ[dg
l]^X]^ilVhYZh^\cZY#
GUARDS & COVERS.<jVgYhVcYXdkZghXVc
egdiZXi ndj [gdbVXX^YZciVa XdciVXil^i] bdk"
^c\ eVgih dg [an^c\ YZWg^h# BV`Z hjgZ i]Zn VgZ
egdeZgan ^chiVaaZY! jcYVbV\ZY! VcY ldg`^c\
XdggZXianWZ[dgZjh^c\bVX]^cZ#
REMOVING TOOLS. CZkZg aZVkZ VY_jhibZci
iddah! X]jX` `Znh! lgZcX]Zh! ZiX# ^c dg dc
bVX]^cZ·ZheZX^VaancZVgbdk^c\eVgih#KZg^[n
gZbdkVaWZ[dgZhiVgi^c\
AWKWARD POSITIONS. @ZZe egdeZg [ddi"
^c\ VcY WVaVcXZ Vi Vaa i^bZh l]Zc deZgVi^c\
bVX]^cZ# 9d cdi dkZggZVX] 6kd^Y Vl`lVgY
]VcYedh^i^dchi]VibV`Zldg`e^ZXZXdcigdaY^["
[^Xjaidg^cXgZVhZi]Zg^h`d[VXX^YZciVa^c_jgn#
DANGEROUS ENVIRONMENTS. 9d cdi jhZ
bVX]^cZgn ^c lZi adXVi^dch! XajiiZgZY VgZVh!
VgdjcY[aVbbVWaZh!dg^ceddgan"a^iVgZVh#@ZZe
ldg`VgZVXaZVc!Ygn!VcYlZaa a^\]iZYidb^c^"
b^oZg^h`d[^c_jgn#
Safety Instructions for Machinery
APPROVED OPERATION. JcigV^cZY deZgVidgh
XVc WZ hZg^djhan ]jgi Wn bVX]^cZgn# Dcan Vaadl
igV^cZY dg egdeZgan hjeZgk^hZY eZdeaZ id jhZ
bVX]^cZ# L]Zc bVX]^cZ ^h cdi WZ^c\ jhZY! Y^h"
XdccZXi edlZg! gZbdkZ hl^iX] `Znh! dg adX`"dji
bVX]^cZidegZkZcijcVji]dg^oZYjhZ·ZheZX^Vaan
VgdjcYX]^aYgZc#BV`Zldg`h]de`^Yegdd[
CHILDREN & BYSTANDERS. @ZZe X]^aYgZc
VcYWnhiVcYZghVhV[ZY^hiVcXZVlVn[gdbldg`
VgZV#Hidejh^c\bVX]^cZ^[X]^aYgZcdgWnhiVcY"
ZghWZXdbZVY^higVXi^dc#
FEED DIRECTION.JcaZhhdi]Zgl^hZcdiZY![ZZY
ldg` V\V^chi i]Z gdiVi^dc d[ WaVYZh dg XjiiZgh#
;ZZY^c\^ci]ZhVbZY^gZXi^dcd[gdiVi^dcbVnejaa
ndjg]VcY^cidi]ZXji#
SECURING WORKPIECE. L]Zc gZfj^gZY! jhZ
XaVbehdgk^hZhidhZXjgZldg`e^ZXZ#6 hZXjgZY
ldg`e^ZXZegdiZXih]VcYhVcY[gZZhWdi]d[i]Zb
iddeZgViZi]ZbVX]^cZ#
UNATTENDED OPERATION. CZkZg aZVkZ
bVX]^cZgjcc^c\l]^aZjcViiZcYZY#IjgcbVX]^cZ
OFFVcYZchjgZVaabdk^c\eVgihXdbeaZiZanhide
WZ[dgZlVa`^c\VlVn#
MAINTENANCE & INSPECTION.6bVX]^cZi]Vi
^h cdi egdeZgan bV^ciV^cZY bVn deZgViZ jcegZ"
Y^XiVWan#;daadlVaa bV^ciZcVcXZ^chigjXi^dchVcY
ajWg^XVi^dc hX]ZYjaZh id `ZZe bVX]^cZ ^c \ddY
ldg`^c\XdcY^i^dc#GZ\jaVgan^cheZXibVX]^cZ[dg
addhZWdaih!Va^\cbZcid[Xg^i^XVaeVgih!W^cY^c\!dg
Vcndi]ZgXdcY^i^dchi]VibVnV[[ZXihV[ZdeZgV"
i^dc# 6alVnh gZeV^g dg gZeaVXZ YVbV\ZY dg b^h"
VY_jhiZYeVgihWZ[dgZdeZgVi^c\bVX]^cZ#
EXPERIENCING DIFFICULTIES. >[ Vi Vcn i^bZ
ndj VgZ ZmeZg^ZcX^c\ Y^[[^Xjai^Zh eZg[dgb^c\ i]Z
^ciZcYZY deZgVi^dc! hide jh^c\ i]Z bVX]^cZ
8dciVXi djg IZX]c^XVa Hjeedgi 9ZeVgibZci Vi
*,%*)+".++(#


Like all machinery there is potential danger when operating this bandsaw. Accidents are frequently
caused by lack of familiarity or failure to pay attention. Use this bandsaw with respect and caution
to reduce the risk of operator injury. If normal safety precautions are overlooked or ignored, seri-
ous personal injury may occur.
Additional Safety for Bandsaws
BLADE CONDITION. 9d cdi deZgViZ l^i] Yjaa!
XgVX`ZYdg WVYan ldgcWaVYZ#9jaa WaVYZh gZfj^gZ
bdgZ Z[[dgi id jhZ VcY VgZ Y^[[^Xjai id Xdcigda#
>cheZXiWaVYZh[dgXgVX`hVcYb^hh^c\iZZi]WZ[dgZ
ZVX]jhZ#
HAND PLACEMENT. EaVX^c\]VcYhdg[^c\Zgh^c
i]ZWaVYZeVi]\gZVian^cXgZVhZhi]ZegdWVW^a^ind[
hZg^djh^c_jgn#6alVnh`ZZe]VcYhdg[^c\Zghdjid[
i]ZWaVYZeVi]l]ZcXjii^c\#
GUARDS. 9d cdi deZgViZ i]^h WVcYhVl l^i]dji
i]ZWaVYZ\jVgY^ceaVXZ#
BLADE REPLACEMENT SAFETY. 7Zh^YZhY^h"
XdccZXi^c\ edlZg l]Zc gZeaVX^c\ WaVYZh! bV`Z
hjgZiZZi][VXZYdlcidlVgYi]ZiVWaZ#I]Z[dgXZd[
i]ZXji^hValVnhYdlc#6ahd!bV`ZhjgZi]ZWaVYZ
^hegdeZganiZch^dcZYV[iZg^chiVaa^c\hd^il^aacdi[an
d[[i]Zl]ZZah#
WORKPIECE HANDLING.CZkZg]daYhbVaaldg`"
e^ZXZhl^i]ndjg[^c\ZghYjg^c\VXji#6alVnhhje"
edgi$[ZZYi]Zldg`e^ZXZl^i]ejh]hi^X`!iVWaZhje"
edgi!k^hZ!dghdbZineZd[XaVbe^c\[^mijgZ#
CUTTING TECHNIQUES. EaVc ndjgXjih hd ndj
ValVnh Xji dji d[ i]Z lddY# 9D CDI WVX` i]Z
ldg`e^ZXZ VlVn [gdb i]Z WaVYZ l]^aZ i]Z hVl ^h
gjcc^c\#>[ndjcZZYidWVX`i]Zldg`dji!ijgci]Z
WVcYhVlD;;VcYlV^i[dgi]ZWaVYZidXdbZidV
XdbeaZiZhide!VcY9DCDIil^hidgejiZmXZhh^kZ
higZhhdci]ZWaVYZl]^aZWVX`^c\ldg`VlVn#
BLADE SPEED. 6aadl WaVYZ id gZVX] [jaa heZZY
WZ[dgZXjii^c\#
UNATTENDED MACHINE. BVX]^cZh aZ[i jcVi"
iZcYZY l]^aZ gjcc^c\ egZhZci bjai^eaZ ]VoVgYh!
^cXajY^c\ k^h^idg YVc\Zg! [^gZ! VcY hZa["^c[a^XiZY
YVbV\Z# 6alVnh ijgc ndjg bVX]^cZ D;; WZ[dgZ
aZVk^c\^i#
DO NOT FORCE THE MACHINE. Id b^c^b^oZ
ndjgg^h`d[eZghdcVa^c_jgn!ldg`Vii]ZheZZY[dg
l]^X] i]Z bVX]^cZ dg VXXZhhdgn lVh YZh^\cZY#
6alVnh[ZZYhidX`ZkZcanVcYhbddi]an#9DCDI
[dgXZdgil^hiWaVYZl]^aZXjii^c\!ZheZX^Vaanl]Zc
hVl^c\hbVaagVY^^#
CUTTING PROPER MATERIAL.I]^hbVX]^cZ^h
cdiYZh^\cZYid Xji bZiVadg Vcn bViZg^VaZmXZei
lddY# 6iiZbei^c\ id Xji di]Zg bViZg^Vah bVn
ZmXZZYi]Za^b^ihd[i]ZbVX]^cZVcY^cXgZVhZi]Z
g^h`d[eZghdcVa^c_jgn#
MAINTENANCE/SERVICE. 6aa ^cheZXi^dch!
VY_jhibZcih! VcY bV^ciZcVcXZ VgZ id WZ YdcZ
l^i] i]Z edlZg D;; VcY i]Z eaj\ gZbdkZY [gdb
i]ZdjiaZi#LV^i[dgVaa bdk^c\eVgih idXdbZ idV
XdbeaZiZhide#
BLADE CONTROL#9dcdiViiZbeiidhidedghadl
i]ZWaVYZl^i]ndjg]VcYdgVldg`e^ZXZ#6aadli]Z
WaVYZidhidedc^ihdlc!jcaZhhndjg bVX]^cZ ^h
Zfj^eeZYl^i]VWgV`Z#
EXPERIENCING DIFFICULTIES.>[ViVcni^bZndj
VgZZmeZg^ZcX^c\Y^[[^Xjai^ZheZg[dgb^c\i]Z^ciZcY"
ZYdeZgVi^dc!hidejh^c\i]ZbVX]^cZ8dciVXidjg
IZX]c^XVaHjeedgi9ZeVgibZciVi*,%*)+".++(#


Full Load Amperage Draw
      

 
 
Power Supply Circuit Requirements

       

       

If you are unsure about
the wiring codes in your area or you plan to
connect your machine to a shared circuit, con-
sult a qualified electrician.
 

SECTION 2: CIRCUIT REQUIREMENTS
Power Connection Device


       
Figure 7
Serious personal injury could occur if you
connect the machine to power before com-
pleting the setup process. DO NOT connect
the machine to the power until instructed
later in this manual.
Electrocution or fire could
result if machine is not
grounded and installed in
compliance with electrical
codes. Compliance MUST
be verified by a qualified
electrician!
NOTICE
The Model G0513/G0514 is prewired for
220V. If you plan to operate the machine at
110V, the motor must be rewired (see Page
54) and a 110V plug must be installed.
Extension Cords

    

 

 

 

Figure 7. 






Wear safety glasses dur-
ing the entire setup pro-
cess!
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
SECTION 3: SETUP
  

Description Qty
 
 Page 16 
  
 
 
 
 
 
 
 
Needed for Setup
      
    
       
please imme-
diately call Customer Service at (570) 546-9663
for advice.

       
Otherwise, filing a freight claim can be difficult.


Unpacking
This machine and its com-
ponents are very heavy.
Get lifting help or use
power lifting equipment
such as a forklift to move
heavy items.


Inventory



Note: If you can't find an item on this list, check
the mounting location on the machine or examine
the packaging materials carefully. Occasionally
we pre-install certain components for shipping
purposes.
Box 1: (Figures 8–9) Qty
A. 
B. 
C. 
D. 
E. 
F. 
G. 
Hardware and Tools (not shown): Qty
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 8. 
       



Figure 9.
SUFFOCATION HAZARD!
Immediately discard all plas-
tic bags and packing materi-
als to eliminate choking/suf-
focation hazards for children
and animals.


Hardware Recognition Chart


Floor Load
Machine Data Sheet
     
     
      

Placement Location
     

       

Figures 1112

Site Considerations
       

      
      Figure 10 

For optimum performance, clean all moving
parts or sliding contact surfaces.  
      
      


Clean Up
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. DO
NOT use these products
to clean the machinery.
Many cleaning solvents
are toxic if inhaled.
Minimize your risk by only
using these products in a
well ventilated area.
G2544—Solvent Cleaner & Degreaser
H9692—Orange Power Degreaser

Figure 10. 

Figure 11.
('
('
Figure 12.
(+
('


To move and place the bandsaw:
1. 
2. Figure 13 

   ,     
        

Moving & Placing
Base Unit
The Model G0513/G0514 is
a heavy machine. Serious
personal injury may occur
if safe moving methods
are not used. To be safe,
get assistance and use
power equipment to move
the shipping crate and
remove the machine from
the crate.
      
       
        


        

        
 

Bolting to Concrete Floors
Figure 14

        



Mounting to Shop
Floor
NOTICE
Anchor studs are stronger and more per-
manent alternatives to lag shield anchors;
however, they will stick out of the floor,
which may cause a tripping hazard if you
decide to move your machine.
Figure14

Figure 13. 
3. 




Figure 16.


2.       
Blade Guides
Page 24 
Table

        

To install the table:
1.       
 
Figure 16
3. 

Personal injury may occur
if the table is lifted without
assistance. Get help when
installing the table.
4. 

5.        
 Figure 17       


Figure 17.

Guide Post
Handwheel
To install the guide post handwheel:
1.       
        
Figure
15.
Figure 15
All saw blades are dan-
gerous and may cause
personal injury. To reduce
the risk of being injured,
wear leather gloves when
handling saw blades.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Grizzly G0514 User manual

Grizzly
Brand
Grizzly
Model
G0514
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents