ESD CPCI-DIO72 Owner's manual

Brand: ESD

Model: CPCI-DIO72

Type: Owner's manual

Installation and technical data CPCI-DIO72 Rev. 1.2

CPCI-DIO72

CompactPCI-digital I/O-Board

Hardware Installation

and

Technical Data

Installation and technical data CPCI-DIO72 Rev. 1.2

Document file: I:\texte\Doku\MANUALS\CPCI\DIO72\CPI7212H.en9

Date of print: 20.12.2001

PCB-version: CPCI-DIO72 Rev. 1.1

Changes in the chapters

The changes in the document listed below affect changes in the hardware as well as changes in the

description of facts only.

Chapter Changes versus previous version

5. Additional types of connector X400.

- -

Technical details are subject to change without further notice.

Installation and technical data CPCI-DIO72 Rev. 1.2

N O T E

The information in this document has been carefully checked and is believed to be entirely reliable. esd

makes no warranty of any kind with regard to the material in this document, and assumes no

responsibility for any errors that may appear in this document. esd reserves the right to make changes

without notice to this, or any of its products, to improve reliability, performance or design.

esd assumes no responsibility for the use of any circuitry other than circuitry which is part of a product

of esd gmbh.

esd does not convey to the purchaser of the product described herein any license under the patent rights

of esd gmbh nor the rights of others.

esd electronic system design gmbh

Vahrenwalder Str. 207

30165 Hannover

Germany

Phone: +49-511-372 98-0

Fax: +49-511-372 98-68

E-mail: [email protected]

Internet: www.esd-electronics.com

USA / Canada

7667 W. Sample Road

Suite 127

Coral Springs, FL 33065

USA

Phone: +1-800-504-9856

Fax: +1-800-288-8235

E-mail: [email protected]

Installation and technical data CPCI-DIO72 Rev. 1.2 1

Contents

1. Overview ................................................................. 3

1.1 Description of the CPCI-DIO72-Board ........................................ 3

1.2 PCB-View with Connector Designation ....................................... 4

1.3 Switching Inputs and Outputs ............................................... 5

2. Hardware Installation ....................................................... 7

3. Summary of Technical Data .................................................. 9

3.1 General Technical Data .................................................... 9

3.2 CompactPCI-Bus ....................................................... 10

3.3 Digital Inputs and Outputs ................................................. 10

3.4 Software Support ....................................................... 11

3.5 Order Information ....................................................... 11

4. LED-Display ............................................................. 13

5. Connector Assignment ..................................................... 15

5.1 Assignment of I/O-Connector X400 ......................................... 15

5.1.1 Connector Type ................................................... 15

5.1.2 Pin Assignment ................................................... 15

5.1.3 Signal Assignment ................................................. 16

6. Circuit Diagrams .......................................................... 17

Installation and technical data CPCI-DIO72 Rev. 1.22

This page is intentionally left blank.

Overview

Installation and technical data CPCI-DIO72 Rev. 1.2 3

FPGA

IRQ

PCI-Bridge

PCI 9054

Half-Pitch

DSUB-

Connector

CompactPCI Connector

Programming

Logics

I/O-Interface

1. Overview

1.1 Description of the CPCI-DIO72-Board

Fig. 1.1: Block-circuit diagram of the CPCI-DIO72-module

The CPCI-DIO72-board is a digital I/O-board which can be universally used in the CompactPCI- system.

It mainly consists of the components input circuit, an FPGA as an I/O-controller and a PCI-bridge.

The board is connected to the Compact-PCI-bus via the PCI-Bridge PCI9054 by PLX Technology,

which is bus-master capable and is therefore able to initiate a PCI-cycle independently.

An FPGA of the Spartan family by Xilinx is used as a programmable logic component. Very complex

functions with a high depth in logic can be realised with this component.

Overview

Installation and technical data CPCI-DIO72 Rev. 1.24

1.2 PCB-View with Connector Designation

Fig. 1.2: Module view (represented without front panel)

Overview

Installation and technical data CPCI-DIO72 Rev. 1.2 5

1.3 Switching Inputs and Outputs

For the flexible switching of directions of the 72 channels, bus exchange switches are used on the CPCI-

DIO72-board. These components have got FET pass transistors and do therefore not have driver abilities

and no predetermined signal direction. A switching of signal directions is therefore not necessary.

The input circuit additionally offers a safety function from positive or negative over voltage caused by

internal clamp diodes.

Furthermore, all signals of the 80-pin socket in the front panel of the CPCI-DIO72-board are in high-

impedance status as long as the CompactPCI system is not switched on and the FPGA has not been

programmed. This high-impedance status can also be triggered by the software.

In each I/O-line a coil and a resistor are connected in series, situated close to the socket. The coil is used

to suppress high-frequency disturbances, while the resistor mutes the vibration tendency of the input line.

Installation and technical data CPCI-DIO72 Rev. 1.26

This page is intentionally left blank.

Installation

Installation and technical data CPCI-DIO72 Rev. 1.2 7

2. Hardware Installation

Attention!

Electro-statical discharges can cause damage to electronic components. In order to prevent this,

please observe the following steps before touching the module to discharge the statical electricity of

your body:

@Switch off the power supply of your computer, but leave it still connected to mains.

@Please touch the metal case of your computer now to discharge yourself.

@Furthermore you should avoid touching the module with your clothes, because these might be

charged electro-statically as well.

Installation procedure:

1. Switch off your computer and all peripheral devices (such as monitors, printers, etc.).

2. Discharge the electro-statical electricity of your body as described above.

3. Disconnect your computer from mains.

4. Insert the CPCI-DIO72-module into a free CompactPCI-bus slot.

5. Fix the CPCI-DIO72-module with the front-panel screw provided.

6. Connect the I/O-signals to the half-pitch DSUB-connector X400 in the front panel.

7. Connect your computer to mains again.

8. Switch the computer and all other devices on again.

9. End of hardware installation.

10. Continue with the software installation (if you have not installed it already).

Installation and technical data CPCI-DIO72 Rev. 1.28

This page is intentionally left blank.

Technical Data

Installation and technical data CPCI-DIO72 Rev. 1.2 9

3. Summary of Technical Data

3.1 General Technical Data

Ambient temperature 0...50°C,

also available for -40 /C...+85 /C

Humidity max. 90 %, non-condensing

Power supply

via CompactPCI-bus,

nominal voltages: 5 V ±5%

3.3 V ±5%

Connectors

X100 (132-pin post connector) -

CompactPCI-board connector

X400 (80-pin DSUB Half-Pitch) - angled mini DSUB-socket

by AMP

Dimensions 100 mm x 160 mm

Weight 160 g

Table 3.1: General data of the module

Technical Data

Installation and technical data CPCI-DIO72 Rev. 1.210

3.2 CompactPCI-Bus

Host bus PCI-bus in accordance with PCI Local Bus Specification 2.1

PCI-data/address bus 32 bits

Controller PCI9054 by PLX Technologie

Interrupt Interrupt signal A

Board dimension in accordance with CompactPCI-Specification, Rev. 1.0

Connectors

Table 3.2: CompactPCI-bus data

3.3 Digital Inputs and Outputs

Number of digital inputs and outputs 72 independent input or output channels

Configuration divided into: 2 x 32 + 8 or

1 x 64 + 8 inputs and outputs

Input voltage suitable for 3.3 V and 5 V signal voltages

Output voltage UOUT = 2.4 V (IOUT = 7 mA)

Safety circuit internal clamp diodes in the driver component

Connector s on board X400 (80-pin DSUB Half-Pitch) - angled mini DSUB-

socket by AMP

Interrupts IRQ with rising or falling edge of an input

DMA-access reading the inputs

Table 3.3: Digital inputs and outputs of the CPCI-DIO72-module

Technical Data

Installation and technical data CPCI-DIO72 Rev. 1.2 11

3.4 Software Support

Drivers are available as object codes for controlling the board. They offer function to configure and read

the inputs and outputs. Furthermore, DMA-accesses to the inputs are supported.

The API will be described in the second part of the manual.

3.5 Order Information

Type Features Order No.

CPCI-DIO72 72 digital inputs and outputs, 0...+50 /CI.2303.02

CPCI-DIO72-T extended temperature range, -40...+85 /CI.2303.03

CPCI-DIO72-RTOS-UH RTOS-UH-Obj.-licence I.2303.54

CPCI-DIO72-VxW VxWorks-Obj.-licence I.2303.55

CPCI-DIO72-ME *) English manual I.2303.21

*) If manual and product are ordered together, the manual is free of charge.

Table 3.5: Order information

Installation and technical data CPCI-DIO72 Rev. 1.212

This page is intentionally left blank.

LED-Display

Installation and technical data CPCI-DIO72 Rev. 1.2 13

01 40

Ejection

handle

LED220A (yellow): BUS

LED220B (red): IRQ

LED220C (green): INIT

LED220D (green): PWR

X400 Half-Pitch

DSUB Connector

4. LED-Display

The module has got four LEDs in the front panel.

Fig. 4.1: Position and colours of the LEDs

LED Colour Name Display function when LED is on

LED220A yellow BUS Host CPU accesses board via PCI-bus

LED220B red IRQ The board triggers a PCI-bus interrupt

LED220C green INIT FPGA is programmed, board is functioning

LED220D green PWR Power - power is supplied

Table 4.1: Display function of the LEDs

Installation and technical data CPCI-DIO72 Rev. 1.214

This page is intentionally left blank.

Connector Assignment

Installation and technical data CPCI-DIO72 Rev. 1.2 15

5. Connector Assignment

5.1 Assignment of I/O-Connector X400

5.1.1 Connector Type

- connector at PCB: 80-pole half pitch male DSUB connector,

AMP order no.: 749830-8 or 787190-8

- connector at wire: 80-pole half pitch female DSUB connector,

AMP order no.: 749621-8 or 749111-7

5.1.2 Pin Assignment

Connector Assignment

Installation and technical data CPCI-DIO72 Rev. 1.216

5.1.3 Signal Assignment

In addition to the 72 I/O-channels, the external synchronisation signal (LATCH), an output enabling

signal (OUTEN) for channels 64-71, the earth potential of the I/O-board is provided here.

Signal Pin Signal

GND 1 41 I/O 37

I/O 00 2 42 I/O 38

I/O 01 3 43 I/O 39

I/O 02 4 44 I/O 40

I/O 03 5 45 I/O 41

I/O 04 6 46 I/O 42

I/O 05 7 47 I/O 43

I/O 06 8 48 I/O 44

I/O 07 9 49 I/O 45

I/O 08 10 50 I/O 46

I/O 09 11 51 I/O 47

I/O 10 12 52 GND

I/O 11 13 53 I/O 48

I/O 12 14 54 I/O 49

I/O 13 15 55 I/O 50

I/O 14 16 56 I/O 51

I/O 15 17 57 I/O 52

GND 18 58 I/O 53

I/O 16 19 59 I/O 54

I/O 17 20 60 I/O 55

I/O 18 21 61 I/O 56

I/O 19 22 62 I/O 57

I/O 20 23 63 I/O 58

I/O 21 24 64 I/O 59

I/O 22 25 65 I/O 60

I/O 23 26 66 I/O 61

I/O 24 27 67 I/O 62

I/O 25 28 68 I/O 63

I/O 26 29 69 GND

I/O 27 30 70 LATCH

I/O 28 31 71 I/O 64

I/O 29 32 72 I/O 65

I/O 30 33 73 I/O 66

I/O 31 34 74 I/O 67

GND 35 75 I/O 68

I/O 32 36 76 I/O 69

I/O 33 37 77 I/O 70

I/O 34 38 78 I/O 71

I/O 35 39 79 OUTEN

I/O 36 40 80 GND

Installation and technical data CPCI-DIO72 Rev. 1.2 17

Circuit Diagrams

6. Circuit Diagrams

The PDF-file of this document does not contain the circuit diagrams. The circuit diagrams are shipped

on request.

Page is loading ...

ESD CPCI-DIO72 Owner's manual

ESD CPCI-DIO72 Owner's manual

ESD CPCI-DIO72 Owner's manual

Related papers

Other documents