Vertiv NetSure™ Inverter System System User guide

Brand: Vertiv

Model: NetSure™ Inverter System System

Type: User guide

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

SYSTEM OVERVIEW

Description: 120 VAC @ up to 23kVA (n+1 ) Inverter System

The Vertiv™ NetSure™ Inverter System is a complete integrated inverter system containing inverters,

intelligent control, metering, monitoring, and distribution.

The inverter system can be set to operate in one of two input power modes, AC Input Power Mode and DC

Input Power Mode.

• In the AC Input Power Mode, each inverter module operates with the commercial AC input to supply

120 VAC power to the loads. In the event commercial AC power fails or becomes abnormal, the

inverter modules immediately transfer operation with the 48 VDC input to power to the inverters.

• In the DC Input Power Mode, each inverter module operates with the 48 VDC input to supply 120 VAC

power to the loads. In the event DC power fails or becomes abnormal or an inverter module fails, the

inverter module immediately transfers operation with the commercial 120 VAC input to power to the

inverters

The inverter system contains an EPO (Emergency Power Off) function. Connection points for a normally

closed external EPO switch are provided on the customer interface board. If an external EPO switch is

wired to the customer interface board, activating the switch to open the circuit activates the EPO function.

The EPO function shuts down and locks out the inverters. When the EPO switch is returned to normal

(closed loop), the inverters remain off. The inverters will restart when the AC and DC power inputs are

removed and restored after 30 seconds or more (until the LEDs on the modules extinguish) (depending on

the synchronizing time with the system). (Note that there is an EPO shorting link factory installed that can

be replaced with a customer provided switch.)

This inverter system consists of the following components. These components are factory packaged to

provide the inverter system configurations listed in Table 1. Note that the values in the table are based on

the ratings of the power system with expansion shelves for Lists 01 thru 06. The other systems are pre-

configured and do not have expansion shelves. The ratings are not only determined by the maximum

number of inverters the system can be provided with, but also the rating of the AC distribution panel. The

overall system rating cannot exceed the AC distribution panel rating.

• Inverter Module Mounting Shelf(s)

The inverter system consists of one or more inverter module mounting shelves, depending on power

rating. The inverter module mounting shelves house the inverter modules.

• Inverter Modules

The inverter system contains 1kVA/1kW inverter modules (1kVA at 40 °C and 0.5kVA at 65 °C),

supplying 120 VAC power from a commercial AC power source or from a 48 VDC input. Refer to the

Inverter Instructions (UM1I1201000) for more information.

• AC Load Distribution Shelf

The inverter system consists of one or more AC load distribution shelves, depending on power rating.

A choice of a bulk output AC load distribution shelf or a NEMA output AC load distribution shelf is

provided.

• NCU (NetSure™ Control Unit) Controller

The controller provides inverter control, metering functions, monitoring functions, and local/remote

alarm functions. The controller also provides data acquisition and system alarm management. The

controller contains a color LCD display and keypad for local access. The controller provides an

Ethernet port and comes with comprehensive webpages for remote access. The controller has SNMP

capability for remote system management. The controller supports software upgrade via its USB port.

Refer to the NCU Controller Instructions (UM1M830BNA) for more information.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List Number Configuration

Stand-Alone System

584130100 List 01 19”, 6kVA maximum, Bulk Output Shelf

584130100 List 02 23”, 5.76kVA maximum, NEMA Output Shelf

584130100 List 03 19”, 12kVA maximum, Bulk Output Shelf

584130100 List 04 23”, 11.5kVA maximum, NEMA Output Shelf

584130100 List 05 19”, 20kVA maximum, Bulk Output Shelf

584130100 List 06 23”, 23kVA maximum, NEMA Output Shelf

Factory Integrated into a Vertiv™ Power System

584130100 List 20 19" Inverter Option, 5kVA maximum, Bulk Output for 58213710050

584130100 List 21 19" Inverter Option, 5kVA maximum, NEMA Output for 58213710051

584130100 List 22 23" Inverter Option, 6kVA maximum, Bulk Output for 58213710052

584130100 List 23 23" Inverter Option, 5.76kVA maximum, NEMA Output for 58213710053

584130100 List 24 19" Inverter Option, 10kVA maximum, Bulk Output for 58213710054

584130100 List 25 19" Inverter Option, 10kVA maximum, NEMA Output for 58213710055

584130100 List 26 23" Inverter Option, 12kVA maximum, Bulk Output for 58213710056

584130100 List 27 23" Inverter Option, 11.5kVA maximum, NEMA Output for 58213710057

584130100 List 30 23" Inverter Option, 6kVA maximum, Bulk Output for 58212700050

584130100 List 31 23" Inverter Option, 5.76kVA maximum, NEMA Output for 58212700051

584130100 List 32 23" Inverter Option, 12kVA maximum, Bulk Output for 58212700052

584130100 List 33 23" Inverter Option, 11.5kVA maximum, NEMA Output for 58212700053

Table 1

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

General Inverter Systems Specifications

See detailed specifications on page 37.

Family: NetSure™

Spec. No.: 584130100

AC Input Voltage: Nominal 120 VAC, single phase, 50 Hz or 60 Hz.

Operating range 96 VAC to 140 VAC.

Acceptable frequency range 47 Hz to 53 Hz or 57 Hz to 63 Hz.

DC Input Voltage: Nominal -48 VDC.

Operating range -40 VDC to -58.5 VDC.

AC Output Voltage 120 VAC, 50 Hz or 60 Hz

AC Output Capacity: See Table 1.

1I1201000 Inverter Rating: See UM1I1201000.

Agency Approval: UL 62368

Framework Type: For mounting in a 19-inch or 23-inch wide relay rack (depending on

configuration)

Mounting Width: 19-inches or 23-inches, nominal (depending on configuration)

Mounting Depth: Varies (see “Overall Dimensions” on page 39)

Mounting Height: Varies (see “Overall Dimensions” on page 39)

Access: Front and Rear for Installation and Maintenance, Front for Operation

Control: Microprocessor

Color: Faceplates: Textured Gray

Other Surfaces: Bright Zinc

Environment: -40 °C to +65 °C (-40 °F to +149 °F)

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

TABLE OF CONTENTS

SYSTEM OVERVIEW ............................................................................................................................................................................................................. 1

MAIN COMPONENTS ILLUSTRATIONS ..........................................................................................................................................................................6

584130100 ........................................................................................................................................................................................................................6

LIST DESCRIPTIONS ............................................................................................................................................................................................................ 7

List Numbers .................................................................................................................................................................................................................... 7

List 01: Inverter System, 19", up to 6kVA maximum (with optional expansion inverter shelf), Bulk Output .......................................... 7

List 02: Inverter System, 23", up to 5.76kVA maximum, NEMA Output ......................................................................................................................... 8

List 03: Inverter System, 19", up to 12kVA maximum (with optional expansion inverter shelf), Bulk Output ....................................... 9

List 04: Inverter System, 23", up to 11.5kVA maximum, NEMA Output ........................................................................................................................10

List 05: Inverter System, 19", up to 20kVA maximum, Bulk Output ................................................................................................................................ 11

List 06: Inverter System, 23", up to 23kVA maximum, NEMA Output .......................................................................................................................... 12

List 10: Field Installed 19” Wide Expansion Inverter Shelf .................................................................................................................................................... 13

List 11: Field Installed 23” Wide Expansion Inverter Shelf ..................................................................................................................................................... 13

List 20: Inverter System, 19", up to 5kVA maximum, Bulk Output for 58213710050 ........................................................................................... 14

List 21: Inverter System, 19", up to 5kVA maximum, NEMA Output for 58213710051 ......................................................................................... 14

List 22: Inverter System, 23", up to 6kVA maximum, Bulk Output for 58213710052 ............................................................................................ 15

List 23: Inverter System, 23", up to 5.76kVA maximum, NEMA Output for 58213710053................................................................................. 15

List 24: Inverter System, 19", up to 10kVA maximum, Bulk Output for 58213710054 ......................................................................................... 16

List 25: Inverter System, 19", up to 10kVA maximum, NEMA Output for 58213710055 ..................................................................................... 16

List 26: Inverter System, 23", up to 12kVA maximum, Bulk Output for 58213710056 ......................................................................................... 17

List 27: Inverter System, 23", up to 11.5kVA maximum, NEMA Output for 58213710057 .................................................................................. 17

List 30: Inverter System, 23", up to 6kVA maximum, Bulk Output for 58212700050 ......................................................................................... 18

List 31: Inverter System, 23", up to 5.76kVA maximum, NEMA Output for 58212700051 ................................................................................. 18

List 32: Inverter System, 23", up to 12kVA maximum, Bulk Output for 58212700052 ......................................................................................... 19

List 33: Inverter System, 23", up to 11.5kVA maximum, NEMA Output for 58212700053 ................................................................................. 19

ACCESSORY DESCRIPTIONS ......................................................................................................................................................................................... 20

Controller ....................................................................................................................................................................................................................... 20

NCU (NetSure™ Control Unit) Controller, P/N 1M830BNA .................................................................................................................................................. 20

Optional Temperature Probes ................................................................................................................................................................................................................. 21

Optional SM-Temp Temperature Concentrator .................................................................................................................................................. 22

SM-Temp Temperature Concentrator, P/N 547490 ................................................................................................................................................................ 22

SM-Temp Jumpers, P/N 552888 ........................................................................................................................................................................................................... 22

Inverter ........................................................................................................................................................................................................................... 22

Inverter Module, P/N 1I1201000 ............................................................................................................................................................................................................ 22

Inverter Module Mounting Position Blank Cover Panel, P/N SXA1100035/1 ............................................................................................................ 22

Relay Racks ................................................................................................................................................................................................................... 23

Relay Rack Earthquake Anchor Kit, P/N 562977 ................................................................................................................................................. 23

Crimp Lugs .................................................................................................................................................................................................................... 23

Standard Crimp Lug Tables ..................................................................................................................................................................................................................... 23

User Replaceable Components ................................................................................................................................................................................ 24

RECOMMENDED WIRE SIZES, BRANCH CIRCUIT PROTECTION, CRIMP LUGS, AND WIRING ILLUSTRATIONS.................................. 24

Relay Rack Frame Grounding Requirements ........................................................................................................................................................ 24

System Shelf Frame Grounding ............................................................................................................................................................................... 24

AC Input Connections (Spec. No. 584130100 List 1 through List 6) .............................................................................................................. 24

AC Input Branch Circuit Protection and Wire Size Selection ............................................................................................................................................. 24

DC Input Connections (Spec. No. 584130100 List 1 through List 6) .............................................................................................................. 24

DC Input Branch Circuit Protection and Wire Size Selection ............................................................................................................................................. 24

AC Output Connections (Spec. No. 584130100 List 01, 03, 05) ...................................................................................................................... 29

AC Output Branch Circuit Protection and Wire Size Selection ......................................................................................................................................... 29

AC Output Connections (Spec. No. 584130100 List 02, 04, 06) ..................................................................................................................... 32

External Alarm, Reference, Monitoring, and Control Connections ................................................................................................................. 33

General .................................................................................................................................................................................................................................................................. 33

External Alarm, Reference, Monitoring, and Control Connections Locations .......................................................................................................... 33

IB2 (Controller Interface Board) (for stand-alone systems only)..................................................................................................................................... 34

Customer Interface Board (for stand-alone systems only) ................................................................................................................................................. 35

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

NCU Controller Ethernet Connection (if required) ............................................................................................................................................. 36

NCU Front Panel Ethernet Port ............................................................................................................................................................................................................. 36

IB4 Board Ethernet Port ............................................................................................................................................................................................................................. 36

SPECIFICATIONS ................................................................................................................................................................................................................ 37

1. System ...................................................................................................................................................................................................................... 37

1.1 AC Input and DC Input Ratings (see also “General Specifications” starting on page 2.) ........................................................................ 37

1.2 AC Output Ratings (see also “General Specifications” starting on page 2.) ................................................................................................... 37

1.3 Environmental Ratings....................................................................................................................................................................................................................... 37

1.4 Compliance Information .................................................................................................................................................................................................................... 38

1.5 IB2 (Controller Interface Board) Ratings ................................................................................................................................................................................ 38

1.6 Safety Standard IEC/EN62040-1-1 ............................................................................................................................................................................................. 38

2. Inverter ..................................................................................................................................................................................................................... 38

3. Controller ................................................................................................................................................................................................................. 38

MECHANICAL SPECIFICATIONS ................................................................................................................................................................................... 39

Overall Dimensions ...................................................................................................................................................................................................... 39

List 01 ..................................................................................................................................................................................................................................................................... 39

List 02 ................................................................................................................................................................................................................................................................... 40

List 03 ..................................................................................................................................................................................................................................................................... 41

List 04 .................................................................................................................................................................................................................................................................... 42

List 05 .................................................................................................................................................................................................................................................................... 43

List 06 .................................................................................................................................................................................................................................................................... 44

Weights........................................................................................................................................................................................................................... 45

RELATED DOCUMENTATION ........................................................................................................................................................................................ 45

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

MAIN COMPONENTS ILLUSTRATIONS

584130100

List 05 and List 06 Shown.

Other Configurations Similar.

NCU Controller

(For Stand-Alone

Systems Only)

IB2 Controller

Interface Board

(slide out panel)

(For Stand-Alone

Systems Only)

NCU Controller

(For Stand-Alone

Systems Only)

IB2 Controller

Interface Board

(slide out panel)

(For Stand-Alone

Systems Only)

Inverter Module Shelf(s)

AC Distribution Shelf(s)

Front View (19-inch system)

Front View (23-inch system)

Rear View (19-inch system)

Rear View (23-inch system)

EPO Board

(located behind rear panel)

IB4 Board

(NCU Second Ethernert Port)

(located behind rear panel)

(For Stand-Alone Systems Only)

EPO Board

(located behind rear panel)

Customer Interface Board

(located behind rear panel)

(For Stand-Alone Systems Only)

Customer Interface Board

(located behind rear panel)

(For Stand-Alone Systems Only)

Inverter Module Shelf(s)

AC Distribution Shelf(s)

IB4 Board

(NCU Second Ethernert Port)

(located behind rear panel)

(For Stand-Alone Systems Only)

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

LIST DESCRIPTIONS

List Numbers

List 01: Inverter System, 19", up to 6kVA maximum (with optional expansion inverter shelf), Bulk Output

Features

♦ Provides a bulk output inverter system consisting of the following factory packaged components.

♦ One (1) 5-position inverter module mounting shelf.

♦ One (1) 1U bulk output AC distribution shelf (includes one 70 A circuit breaker).

♦ Accepts one (1) NCU Controller.

♦ Includes the IB4 board (provides a network connection point for NCU remote access).

♦ Includes the IB2 controller interface board (provides eight (8) programmable form C- relay outputs, eight (8)

programmable binary inputs, and two (2) temperature inputs).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

♦ Includes the customer interface board (see Figure 7).

Restrictions

For stand-alone applications.

Mounts in a 19" wide relay rack.

One (1) expansion inverter shelf can be added to a List 01.

Maximum system output power when equipped with a single 19-inch-wide inverter shelf is 5kVA at 40 °C and 2.5kVA at 65 °C.

Maximum system output power when equipped with two (2) 19-inch-wide inverter shelves is 6kVA at 40 °C and 5kVA at

65 °C.

Output load not to exceed 80% (56 A) of rated value of circuit breaker at 40 °C and 65 °C.

Ordering Notes

1) Order a relay rack or shipping brackets per “Relay Racks” on page 23.

2) Order one (1) NCU Controller P/N 1M830BNA (see page 20).

Also specify appropriate configuration file for your site.

3) Order up to five (5) inverter modules P/N 1I1201000 (see page 22).

4) Order an inverter mounting position blank cover panel P/N SXA1100035/1 for each empty inverter mounting position in

the system as desired (see page 22).

5) Order optional temperature probes for ambient and battery temperature monitoring as required. Refer to “Optional

Temperature Probes” on page 21.

6) Order DC input lugs as required per “Crimp Lugs” on page 23.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 02: Inverter System, 23", up to 5.76kVA maximum, NEMA Output

Features

♦ Provides a NEMA output inverter system consisting of the following factory packaged components.

♦ One (1) 6-position inverter module mounting shelf.

♦ One (1) 2U NEMA output AC distribution shelf (includes eight 15 A circuit breakers).

♦ Accepts one (1) NCU Controller.

♦ Includes the IB4 board which provides a network connection point for NCU remote access.

♦ Includes the IB2 controller interface board (provides eight (8) programmable form C- relay outputs, eight (8)

programmable binary inputs, and two (2) temperature inputs).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

♦ Includes the customer interface board (see Figure 7).

Restrictions

For stand-alone applications.

Mounts in a 23" wide relay rack.

One (1) expansion inverter shelf can be added to a List 02.

Maximum system output power when equipped with a single 23-inch-wide inverter shelf is 5.76kVA at 40 °C and 3kVA at

65 °C.

Maximum system output power when equipped with two (2) 23-inch-wide inverter shelves is 5.76kVA at 40 °C and 65 °C.

Maximum output load per 15 A NEMA outlet is 12 A at 40 °C and 65 °C.

Output load not to exceed 80% (12 A) of rated value of circuit breaker at 40 °C and 65 °C.

Ordering Notes

1) Order a relay rack or shipping brackets per “Relay Racks” on page 23.

2) Order one (1) NCU Controller P/N 1M830BNA (see page 20).

Also specify appropriate configuration file for your site.

3) Order up to six (6) inverter modules P/N 1I1201000 (see page 22).

4) Order an inverter mounting position blank cover panel P/N SXA1100035/1 for each empty inverter mounting position in

the system as desired (see page 22).

5) Order optional temperature probes for ambient and battery temperature monitoring as required. Refer to “Optional

Temperature Probes” on page 21.

6) Order DC input lugs as required per “Crimp Lugs” on page 23.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 03: Inverter System, 19", up to 12kVA maximum (with optional expansion inverter shelf), Bulk Output

Features

♦ Provides a bulk output inverter system consisting of the following factory packaged components.

♦ Two (2) 5-position inverter module mounting shelves.

♦ One (1) 2U bulk output AC distribution shelf (includes two 70 A circuit breakers).

♦ Accepts one (1) NCU Controller.

♦ Includes the IB4 board (provides a network connection point for NCU remote access).

♦ Includes the IB2 controller interface board (provides eight (8) programmable form C- relay outputs, eight (8)

programmable binary inputs, and two (2) temperature inputs).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

♦ Includes the customer interface board (see Figure 7).

Restrictions

For stand-alone applications.

Mounts in a 19" wide relay rack.

One (1) expansion inverter shelf can be added to a List 03.

Maximum system output power when equipped with two (2) 19-inch-wide inverter shelves is 10kVA at 40 °C and 5kVA at

65 °C.

Maximum system output power when equipped with three (3) 19-inch-wide inverter shelves is 12kVA at 40 °C and 7.5kVA at

65 °C.

Output load not to exceed 80% (56 A) of rated value of circuit breaker at 40 °C and 65 °C.

Ordering Notes

1) Order a relay rack or shipping brackets per “Relay Racks” on page 23.

2) Order one (1) NCU Controller P/N 1M830BNA (see page 20).

Also specify appropriate configuration file for your site.

3) Order up to ten (10) inverter modules P/N 1I1201000 (see page 22).

4) Order an inverter mounting position blank cover panel P/N SXA1100035/1 for each empty inverter mounting position in

the system as desired (see page 22).

5) Order optional temperature probes for ambient and battery temperature monitoring as required. Refer to “Optional

Temperature Probes” on page 21.

6) Order DC input lugs as required per “Crimp Lugs” on page 23.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 04: Inverter System, 23", up to 11.5kVA maximum, NEMA Output

Features

♦ Provides a NEMA output inverter system consisting of the following factory packaged components.

♦ Two (2) 6-position inverter module mounting shelves.

♦ One (1) 2U NEMA output AC distribution shelf (includes eight 15 A circuit breakers).

♦ Accepts one (1) NCU Controller.

♦ Includes the IB4 board (provides a network connection point for NCU remote access).

♦ Includes the IB2 controller interface board (provides eight (8) programmable form C- relay outputs, eight (8)

programmable binary inputs, and two (2) temperature inputs).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

♦ Includes the customer interface board (see Figure 7).

Restrictions

For stand-alone applications.

Mounts in a 23" wide relay rack.

One (1) expansion inverter shelf can be added to a List 04.

Maximum system output power when equipped with two (2) 23-inch-wide inverter shelves is 11.5kVA at 40 °C.

Maximum system output power when equipped with two (2) 23-inch-wide inverter shelves is 6kVA at 65 °C.

Maximum system output power when equipped with three (3) 23-inch-wide inverter shelves is 9kVA at 65 °C.

Maximum output load per 15 A NEMA outlet is 12 A at 40 °C and 65 °C.

Output load not to exceed 80% (12 A) of rated value of circuit breaker at 40 °C and 65 °C.

Ordering Notes

1) Order a relay rack or shipping brackets per “Relay Racks” on page 23.

2) Order one (1) NCU Controller P/N 1M830BNA (see page 20).

Also specify appropriate configuration file for your site.

3) Order up to twelve (12) inverter modules P/N 1I1201000 (see page 22).

4) Order an inverter mounting position blank cover panel P/N SXA1100035/1 for each empty inverter mounting position in

the system as desired (see page 22).

5) Order optional temperature probes for ambient and battery temperature monitoring as required. Refer to “Optional

Temperature Probes” on page 21.

6) Order DC input lugs as required per “Crimp Lugs” on page 23.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 05: Inverter System, 19", up to 20kVA maximum (with optional expansion inverter shelf), Bulk Output

Features

♦ Provides a bulk output inverter system consisting of the following factory packaged components.

♦ Three (3) 5-position inverter module mounting shelves.

♦ Two (1) 2U bulk output AC distribution shelves (each includes two 70 A circuit breakers).

♦ Accepts one (1) NCU Controller.

♦ Includes the IB4 board (provides a network connection point for NCU remote access).

♦ Includes the IB2 controller interface board (provides eight (8) programmable form C- relay outputs, eight (8)

programmable binary inputs, and two (2) temperature inputs).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

♦ Includes the customer interface board (see Figure 7).

Restrictions

For stand-alone applications.

Mounts in a 19" wide relay rack.

One (1) expansion inverter shelf can be added to a List 05.

Maximum system output power when equipped with three (3) 19-inch-wide inverter shelves is 15kVA at 40 °C and 7.5kVA at

65 °C.

Maximum system output power when equipped with four (4) 19-inch-wide inverter shelves is 20kVA at 40 °C and 10kVA at

65 °C.

Output load not to exceed 80% (56 A) of rated value of circuit breaker at 40 °C and 65 °C.

Ordering Notes

1) Order a relay rack or shipping brackets per “Relay Racks” on page 23.

2) Order one (1) NCU Controller P/N 1M830BNA (see page 20).

Also specify appropriate configuration file for your site.

3) Order up to fifteen (15) inverter modules P/N 1I1201000 (see page 22).

4) Order an inverter mounting position blank cover panel P/N SXA1100035/1 for each empty inverter mounting position in

the system as desired (see page 22).

5) Order optional temperature probes for ambient and battery temperature monitoring as required. Refer to “Optional

Temperature Probes” on page 21.

6) Order DC input lugs as required per “Crimp Lugs” on page 23.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 06: Inverter System, 23", up to 23kVA maximum (with optional expansion inverter shelf), NEMA Output

Features

♦ Provides a NEMA output inverter system consisting of the following factory packaged components.

♦ Three (3) 6-position inverter module mounting shelves.

♦ Two (2) 2U NEMA output AC distribution shelves (each includes eight 15 A circuit breakers).

♦ Accepts one (1) NCU Controller.

♦ Includes the IB4 board (provides a network connection point for NCU remote access).

♦ Includes the IB2 controller interface board (provides eight (8) programmable form C- relay outputs, eight (8)

programmable binary inputs, and two (2) temperature inputs).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

♦ Includes the customer interface board (see Figure 7).

Restrictions

For stand-alone applications.

Mounts in a 23" wide relay rack.

One (1) expansion inverter shelf can be added to a List 06.

Maximum system output power when equipped with three (3) 23-inch-wide inverter shelves is 18kVA at 40 °C and 9kVA at

65 °C.

Maximum system output power when equipped with four (4) 23-inch-wide inverter shelves is 23kVA at 40 °C and 12kVA at

65 °C.

Maximum output load per 15 A NEMA outlet is 12 A at 40 °C and 65 °C.

Output load not to exceed 80% (12 A) of rated value of circuit breaker at 40 °C and 65 °C.

Ordering Notes

1) Order a relay rack or shipping brackets per “Relay Racks” on page 23.

2) Order one (1) NCU Controller P/N 1M830BNA (see page 20).

Also specify appropriate configuration file for your site.

3) Order up to eighteen (18) inverter modules P/N 1I1201000 (see page 22).

4) Order an inverter mounting position blank cover panel P/N SXA1100035/1 for each empty inverter mounting position in

the system as desired (see page 22).

5) Order optional temperature probes for ambient and battery temperature monitoring as required. Refer to “Optional

Temperature Probes” on page 21.

6) Order DC input lugs as required per “Crimp Lugs” on page 23.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 10: Field Installed 19” Wide Expansion Inverter Shelf

Features

♦ Provides a field installed 19” wide inverter module mounting shelf.

♦ Includes busbars and CAN jumpers to connect to an existing inverter shelf.

Restrictions

Field installed.

Can only be used with List 01, List 03, and List 05. Maximum of one (1) expansion shelf per List 01, List 03, and List 05.

Mounted to top of existing system only.

Ordering Notes

1) Order up to five (5) inverter modules P/N 1I1201000 (see page 22).

2) Order an inverter mounting position blank cover panel P/N SXA1100035/1 for each empty inverter mounting position in

the system as desired (see page 22).

List 11: Field Installed 23” Wide Expansion Inverter Shelf

Features

♦ Provides a field installed 23” wide inverter module mounting shelf.

♦ Includes busbars and CAN jumpers to connect to an existing inverter shelf.

Restrictions

Field installed.

Can only be used with List 02, List 04, and List 06. Maximum of one (1) expansion shelf per List 02, List 04, and List 06.

Mounted to top of existing system only.

Ordering Notes

1) Order up to six (6) inverter modules P/N 1I1201000 (see page 22).

2) Order an inverter mounting position blank cover panel P/N SXA1100035/1 for each empty inverter mounting position in

the system as desired (see page 22).

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 20: Inverter System, 19", up to 5kVA maximum, Bulk Output for 58213710050

Features

♦ Provides a bulk output inverter system to be used in Spec. No. 582137100 Vertiv™ NetSure™ Power System.

♦ One (1) 5-position inverter module mounting shelf.

♦ One (1) 1U bulk output AC distribution shelf (includes one 70 A circuit breaker).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with one (1) 19-inch-wide inverter shelf is 5kVA at 40 °C and 2.5kVA at 65 °C.

Ordering Notes

1) Order Spec. No. 58213710050 via power system documentation.

List 21: Inverter System, 19", up to 5kVA maximum, NEMA Output for 58213710051

Features

♦ Provides a NEMA output inverter system to be used in Spec. No. 582137100 Vertiv™ NetSure™ Power System.

♦ One (1) 5-position inverter module mounting shelf.

♦ One (1) 1U NEMA output AC distribution shelf (includes four 15 A circuit breakers).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with one (1) 19-inch-wide inverter shelf is 5kVA at 40 °C and 2.5kVA at 65 °C.

Ordering Notes

1) Order Spec. No. 58213710051 via power system documentation.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 22: Inverter System, 23", up to 6kVA maximum, Bulk Output for 58213710052

Features

♦ Provides a bulk output inverter system to be used in Spec. No. 582137100 Vertiv™ NetSure™ Power System.

♦ One (1) 6-position inverter module mounting shelf.

♦ One (1) 1U bulk output AC distribution shelf (includes one 70 A circuit breaker).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with one (1) 23-inch-wide inverter shelf is 6kVA at 40 °C and 3kVA at 65 °C.

Ordering Notes

1) Order Spec. No. 58213710052 via power system documentation.

List 23: Inverter System, 23", up to 5.76kVA maximum, NEMA Output for 58213710053

Features

♦ Provides a NEMA output inverter system to be used in Spec. No. 582137100 Vertiv™ NetSure™ Power System.

♦ One (1) 6-position inverter module mounting shelf.

♦ One (1) 1U NEMA output AC distribution shelf (includes four 15 A circuit breakers)..

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with one (1) 23-inch-wide inverter shelf is 5.76kVA at 40 °C and 3kVA at

65 °C.

Ordering Notes

1) Order Spec. No. 58213710053 via power system documentation.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 24: Inverter System, 19", up to 10kVA maximum, Bulk Output for 58213710054

Features

♦ Provides a bulk output inverter system to be used in Spec. No. 582137100 Vertiv™ NetSure™ Power System.

♦ Two (2) 5-position inverter module mounting shelves.

♦ One (1) 2U bulk output AC distribution shelf (includes two 70 A circuit breakers).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with two (2) 19-inch-wide inverter shelf is 10kVA at 40 °C and 5kVA at 65 °C.

Ordering Notes

1) Order Spec. No. 58213710054 via power system documentation.

List 25: Inverter System, 19", up to 10kVA maximum, NEMA Output for 58213710055

Features

♦ Provides a NEMA output inverter system to be used in Spec. No. 582137100 Vertiv™ NetSure™ Power System.

♦ Two (2) 5-position inverter module mounting shelves.

♦ One (1) 2U NEMA output AC distribution shelf (includes eight 15 A circuit breakers).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with two (2) 19-inch-wide inverter shelf is 10kVA at 40 °C and 5kVA at 65 °C.

Ordering Notes

1) Order Spec. No. 58213710055 via power system documentation.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 26: Inverter System, 23", up to 12kVA maximum, Bulk Output for 58213710056

Features

♦ Provides a bulk output inverter system to be used in Spec. No. 582137100 Vertiv™ NetSure™ Power System.

♦ Two (2) 6-position inverter module mounting shelves.

♦ One (1) 2U bulk output AC distribution shelf (includes two 70 A circuit breakers).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with two (2) 23-inch-wide inverter shelf is 12kVA at 40 °C and 6kVA at 65 °C.

Ordering Notes

1) Order Spec. No. 58213710056 via power system documentation.

List 27: Inverter System, 23", up to 11.5kVA maximum, NEMA Output for 58213710057

Features

♦ Provides a NEMA output inverter system to be used in Spec. No. 582137100 Vertiv™ NetSure™ Power System.

♦ Two (2) 6-position inverter module mounting shelves.

♦ One (1) 2U NEMA output AC distribution shelf (includes eight 15 A circuit breakers).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with two (2) 23-inch-wide inverter shelf is 11.5kVA at 40 °C and 6kVA at

65 °C.

Ordering Notes

1) Order Spec. No. 58213710057 via power system documentation.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 30: Inverter System, 23", up to 6kVA maximum, Bulk Output for 58212700050

Features

♦ Provides a bulk output inverter system to be used in Spec. No. 582127000 Vertiv™ NetSure™ Power System.

♦ One (1) 6-position inverter module mounting shelf.

♦ One (1) 1U bulk output AC distribution shelf (includes one 70 A circuit breaker).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with one (1) 23-inch-wide inverter shelf is 6kVA at 40 °C and 3kVA at 65 °C.

Ordering Notes

1) Order Spec. No. 58212700050 via power system documentation.

List 31: Inverter System, 23", up to 5.76kVA maximum, NEMA Output for 58212700051

Features

♦ Provides a NEMA output inverter system to be used in Spec. No. 582127000 Vertiv™ NetSure™ Power System.

♦ One (1) 6-position inverter module mounting shelf.

♦ One (1) 1U NEMA output AC distribution shelf (includes four 15 A circuit breakers)..

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with one (1) 23-inch-wide inverter shelf is 5.76kVA at 40 °C and 3kVA at

65 °C.

Ordering Notes

1) Order Spec. No. 58212700051 via power system documentation.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

List 32: Inverter System, 23", up to 12kVA maximum, Bulk Output for 58212700052

Features

♦ Provides a bulk output inverter system to be used in Spec. No. 582127000 Vertiv™ NetSure™ Power System.

♦ Two (2) 6-position inverter module mounting shelves.

♦ One (1) 2U bulk output AC distribution shelf (includes two 70 A circuit breakers).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with two (2) 23-inch-wide inverter shelf is 12kVA at 40 °C and 6kVA at 65 °C.

Ordering Notes

1) Order Spec. No. 58212700052 via power system documentation.

List 33: Inverter System, 23", up to 11.5kVA maximum, NEMA Output for 58212700053

Features

♦ Provides a NEMA output inverter system to be used in Spec. No. 582127000 Vertiv™ NetSure™ Power System.

♦ Two (2) 6-position inverter module mounting shelves.

♦ One (1) 2U NEMA output AC distribution shelf (includes eight 15 A circuit breakers).

♦ Includes the EPO (Emergency Power Off) board which provides the EPO function.

Restrictions

Not a stand-alone system. Factory integrated into a Vertiv™ Power System.

Maximum system output power when equipped with two (2) 23-inch-wide inverter shelf is 11.5kVA at 40 °C and 6kVA at

65 °C.

Ordering Notes

1) Order Spec. No. 58212700053 via power system documentation.

Vertiv™ NetSure™ Inverter System

System Application Guide

Spec. No: 584130100 SAG584130100

Revision A, July 23, 2021

ACCESSORY DESCRIPTIONS

Controller

NCU (NetSure™ Control Unit) Controller, P/N 1M830BNA

Features

♦ NCU Controller, Model M830BNA (Spec. No. 1M830BNA).

♦ Factory programmed with the configuration file specified when ordered.

Note:

The controller is provided with the factory default configuration

unless otherwise specified.

Note:

♦ Refer to the NCU Controller Instructions (UM1M830BNA) for more

information.

Restrictions

Only one (1) controller per inverter system is required.

Ordering Notes

1) Order one (1) NCU controller per inverter system, P/N 1M830BNA.

2) Order optional temperature probes for ambient and battery temperature monitoring as required. Refer to “Optional

Temperature Probes” on page 21.

3) Order optional SM-Temp Temperature Concentrator (Supervisory Module for Temperature Probes) as desired (shipped

loose) (see page 22). Also order SM-Temp CAN Bus Interface Cable, P/N 562868, and “SM-Temp Jumpers, P/N 552888”

(see page 22) as required.

Note:

A system can have up to (8) SM-Temp modules (each of which can accept up to eight temperature probes) that

can be used in the power system for ambient and battery monitoring.

4) Ordering an NCU for replacing an NCU or as a spare NCU.

If the NCU is to be used as a replacement in a specific system, it should be ordered with the same configuration file as

the original NCU controller. This is identified by a six-digit number. If the controller part number ends with a six-digit

number, for example, 1M830BNA559242, the configuration file number is the last six characters. If the part number does

not have these characters, the configuration file number can be found on the controller nameplate – “Programmed with

Configuration File ######”. The controller may also have a Unique Identification Number (UIN). This number indicates

that certain parameters were set at the factory to match the controller to the options selected with the power plant. If

the controller has a UIN, the plant will have shipped with a USB drive labelled with the UIN. The UIN label may also be

located near the controller slot in the system. If the controller has a UIN, provide this UIN number, along with the

configuration number, when ordering so that the new controller will match that of the original controller shipped with the

system. The user manual provided with the controller provides instructions for replacing and programming the

controller. It is important to follow these instructions carefully. The user manual also provides instructions for saving

certain controller files that are created when changes are made to the system after leaving the factory. These files can

be programmed into the replacement controller so it can match the latest saved state of the original controller.

If the NCU is being ordered as a spare part for any of a group of power plants, the same procedure can be followed. If the

replacement controller’s configuration does not match that of the original controller, the original files can be retrieved

from the USB drive shipped with the plant, if available. If the USB drive is not available, contact the factory or technical

assistance center to obtain a copy of the original configuration file (all package) so it can be programmed into the new

controller.

Page is loading ...

Vertiv NetSure™ Inverter System System User guide

Vertiv NetSure™ Inverter System System User guide

Vertiv NetSure™ Inverter System System User guide

Related papers

Other documents