Timeguard LEDMRQ18WHEMMS Operating instructions

Brand: Timeguard

Model: LEDMRQ18WHEMMS

Type: Operating instructions

Installation & Operating Instructions

18W Round LED Slimline

Emergency Light

with Microwave Sensor

Model: LEDMRQ18WHEMMS

1 2

1. General Information

These instructions should be read carefully and retained for further reference

and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the luminaire

is switched off and the circuit supply fuses are removed or the circuit breaker

turned off.

• It is recommended that a qualified electrician is consulted or used for the

installation of this luminaire and install in accordance with the current

IEE wiring and Building Regulations.

• Check that the total load on the circuit including when this luminaire is fitted

does not exceed the rating of the circuit cable, fuse or circuit breaker.

• Do not dismantle the lamp or unscrew the LED board, this will affect the heat

distribution and reduce the lifespan of the LED luminaire.

• Never clean with a damp cloth whilst the luminaire is switched ON.

2 3

3. Technical Specifications

• 230V AC 50 Hz

• This luminaire is of class II construction and must not be earthed

• 18W LED Non-replaceable lamp

• Energy efficiency: Class A

• Energy Usage: 18KwH/1000H

• Lumen Output: 1680lm

• Emergency Output: 50% (752lm)

• Emergency duration: > 3 hours

• Colour Temperature: 4000K

• Operating Temperature: 0ºC to +40ºC

• Battery charge time: 24 hours (Non-replaceable rechargeable)

• Power Status Indicator: Green LED when mains power is ON.

• Detection Angle: 360° ceiling, 180° wall mounted

• Detection Range Adjustment: 1m to 8m (at a mounting height of 2.5m)

• Time On Adjustment: 5 seconds to 30minutes

• Lux Range Adjustment: 5 to 50 lux

• IP20 Rated suitable for internal use only

• CE Compliant

• Dimensions: 285mm diameter x 56mm

• Mounting Centres: 40mm

3 4

4. Installation

Note: A permanent supply live is required to charge the internal battery,

which is used in emergency mode.

4.1 Ensure the mains supply is switched off and the circuit supply fuses are

removed or the circuit breaker turned off.

4.2 Rotate the back plate anti-clockwise to unscrew, lift the back plate away

from the luminaire. Carefully disconnect the 2 way plug by holding down

the locking bar on one half, at the same time grip the opposite side

and pull apart. This will disconnect the back plate completely.

4.3 Using the back plate as a template, mark the position of the mounting

holes on the wall or ceiling.

4.4 Drill the holes for the rawl plugs ensuring not to infringe with any

gas/water pipes or electrical cables that may be hidden below the surface.

Insert the rawl plugs into the holes.

4.5 Pass the 230V AC 50Hz mains supply cable through the back plate.

4.6 Fix the back plate to the ceiling or wall using the correct screws

for the rawl plugs installed.

4.7 Terminate the supply cable into the spring clamp terminal block

(See section 5. Connection Diagram) ensuring correct polarity is observed

and that all bare conductors are sleeved.

4.8 Re-connect the 2 way plug by pushing the plug and socket together

until they lock. DO NOT FORCE. THE PLUG AND SOCKET WILL ONLY FIT

TOGETHER ONE WAY AROUND.

4.9 Reposition the luminaire over the back plate, rotate the luminaire clockwise

to screw into place and secure.

5. Connection Diagram

• This luminaire uses a spring clamp terminal for connection as shown;

Push down the spring lever

here and hold.

Insert wire and release lever

to clamp into place.

230V AC 50Hz

MAINS SUPPL

LOOP

TERMINAL

Permanent Live to charge battery

5 6

• Connect the 230V AC 50Hz mains supply cable

to the spring clamp terminal as follows:

• Use the provided cable clamp to secure the mains supply cable

to the back plate.

6. Setting Up & Testing

Walk Test

• The adjustable DIP switches are factory set to “Walk Test” mode i.e. Detection

Area set to ‘100%’, the Hold Time set to the minimum of ‘5 seconds’ and the

Daylight Sensor set to ‘Disable’.

• Turn the power to the unit ON. The luminaire will immediately turn ON as

the unit goes through its ‘warm-up’ period. After approximately 10 seconds the

light will extinguish. This indicates the luminaire is wired correctly and the unit

is in “Walk Test” mode. The green LED indicator will illuminate when mains

power is present.

• Try to remain out of the area of detection during the ‘warm-up’ period.

Note: A permanent supply live is required

to charge the internal battery, which is

used in emergency mode.

230V 50Hz Mains Supply

Live Supply (Brown or Red) to L

Neutral Supply (Blue or Black) to N

A ‘Loop Terminal’ (centre terminal) is provided should a 3 core

cable be used

Noted item:

1.This product must be installed or dismantled by qualified electrician.

2.The driver is placed inside, and its input voltage is 220-240V/AC,50/60Hz.

3.Please make sure the power is off before installing and maintenance, and check

the power cable is properly connected before switching on the lamp.

4.Always obey the fire code, and make sure the lamp has at least 7.5cm space to

ventilate.

5.Don't install the lamp on inflammable, sloping, or damaged surface.

6.Never clean the lamp with dump cloth when the lamp is switched on.

To Customers:

Thank you for purchasing our goods.

Please read the manual before using, and keep it for reference.

Installing instruction:

1.Unscrew the installing plate from the lamp and disconnect the wires on the

terminal block.

2.Connect the utility supply to terminal block (L for live wire, N for null wire) on the

installing plate, then fix the installing plate on the ceiling or wall by screws.

3.Connect the wires from lamp to the terminal block and combine the installing

plate with the lamp by rotating.

Special attention:

1.Don't dismantle the lamp or unscrew the led broad, otherwise it will affect the

heat dissipation, and reduce the lifespan of the led ceiling light.

2.If you have any question about the product, please consult our professional

engineers.

Adjustable Microwave

USER MANUAL

Add: No.16 Ind. Road, Xiaolan Ind. Zone, Xiaolan Town, Zhongshan,G.D., China

Contact e-mail: [email protected]

Website:

www.hanrun-lighting.com

5ETGY*QNGU

6GTOKPCN$NQEM

Open the cover to adjust the microwave setting.

Add: No.16 Ind. Road, Xiaolan Ind. Zone, Xiaolan Town, Zhongshan,G.D., China

Contact e-mail: [email protected]

Website:

www.hanrun-lighting.com

• The luminaire will now operate during daytime as well as at night, turning ON

for approx. 5 seconds each time the sensor is activated. This allows testing

to be carried out to establish whether the microwave sensor is covering

the required area.

• Walk around the luminaire to establish the detection area.

• The microwave sensor will detect within an 8m diameter (approximately) from

the centre of the luminaire location when mounted at a 2.5m height.

• As you cross a detection “zone” the luminaire will turn ON. Now stand still

until the luminaire extinguishes (this should take approx. 5 seconds).

• Start moving again after 2 seconds. As you cross each “zone” the luminaire

will turn ON.

• Repeat the above, walking at various distances and angles to the luminaire.

This will help you to confirm the detection pattern.

Setting Up for Automatic Operation

• When walk tests are complete, the luminaire can be adjusted for

automatic operation.

• Ensure the power to the luminaire is switched OFF, and then disconnect

the luminaire from the back plate using step 4.2, as detailed in

section 4. Installation.

Note: if the internal battery is charged the luminaire will turn ON whilst you

adjust it, running at 50% output for up to 3 hours (see section 7. Emergency

Mode & Internal Battery for further details).

• To access the adjustable DIP switches, undo and remove the 4 fixing screws

that hold the bezel and plastic lens cover to the base of the luminaire.

The DIP switches are located on the LED board.

Noted item:

1.This product must be installed or dismantled by qualified electrician.

2.The driver is placed inside, and its input voltage is 220-240V/AC,50/60Hz.

3.Please make sure the power is off before installing and maintenance, and check

the power cable is properly connected before switching on the lamp.

4.Always obey the fire code, and make sure the lamp has at least 7.5cm space to

ventilate.

5.Don't install the lamp on inflammable, sloping, or damaged surface.

6.Never clean the lamp with dump cloth when the lamp is switched on.

To Customers:

Thank you for purchasing our goods.

Please read the manual before using, and keep it for reference.

Installing instruction:

1.Unscrew the installing plate from the lamp and disconnect the wires on the

terminal block.

2.Connect the utility supply to terminal block (L for live wire, N for null wire) on the

installing plate, then fix the installing plate on the ceiling or wall by screws.

3.Connect the wires from lamp to the terminal block and combine the installing

plate with the lamp by rotating.

Special attention:

1.Don't dismantle the lamp or unscrew the led broad, otherwise it will affect the

heat dissipation, and reduce the lifespan of the led ceiling light.

2.If you have any question about the product, please consult our professional

engineers.

Adjustable Microwave

USER MANUAL

Add: No.16 Ind. Road, Xiaolan Ind. Zone, Xiaolan Town, Zhongshan,G.D., China

Contact e-mail: [email protected]

Website:

www.hanrun-lighting.com

5ETGY*QNGU

6GTOKPCN$NQEM

Open the cover to adjust the microwave setting.

Add: No.16 Ind. Road, Xiaolan Ind. Zone, Xiaolan Town, Zhongshan,G.D., China

Contact e-mail: [email protected]

Website:

www.hanrun-lighting.com

Noted item:

1.This product must be installed or dismantled by qualified electrician.

2.The driver is placed inside, and its input voltage is 220-240V/AC,50/60Hz.

3.Please make sure the power is off before installing and maintenance, and check

the power cable is properly connected before switching on the lamp.

4.Always obey the fire code, and make sure the lamp has at least 7.5cm space to

ventilate.

5.Don't install the lamp on inflammable, sloping, or damaged surface.

6.Never clean the lamp with dump cloth when the lamp is switched on.

To Customers:

Thank you for purchasing our goods.

Please read the manual before using, and keep it for reference.

Installing instruction:

1.Unscrew the installing plate from the lamp and disconnect the wires on the

terminal block.

2.Connect the utility supply to terminal block (L for live wire, N for null wire) on the

installing plate, then fix the installing plate on the ceiling or wall by screws.

3.Connect the wires from lamp to the terminal block and combine the installing

plate with the lamp by rotating.

Special attention:

1.Don't dismantle the lamp or unscrew the led broad, otherwise it will affect the

heat dissipation, and reduce the lifespan of the led ceiling light.

2.If you have any question about the product, please consult our professional

engineers.

Adjustable Microwave

USER MANUAL

Add: No.16 Ind. Road, Xiaolan Ind. Zone, Xiaolan Town, Zhongshan,G.D., China

Contact e-mail: [email protected]

Website:

www.hanrun-lighting.com

5ETGY*QNGU

6GTOKPCN$NQEM

Open the cover to adjust the microwave setting.

Add: No.16 Ind. Road, Xiaolan Ind. Zone, Xiaolan Town, Zhongshan,G.D., China

Contact e-mail: [email protected]

Website:

www.hanrun-lighting.com

7 8

HELPLINE

020 8450 0515

• The ‘Detection Area’ setting controls determines the range of detection.

• The ‘Hold Time’ setting controls how long the luminaire remains ON

following activation and after all motion ceases.

100% DIP switches 1, 2, 3 ON

75% DIP switch 1 OFF – DIP switches 2, 3 ON

50% DIP switch 1 ON – DIP switch 2 OFF – DIP switch 3 ON

25% DIP switches 1, 2 OFF – DIP switch 3 ON

10% DIP switches 1, 2, 3 OFF

5 seconds DIP switches 4, 5, 6 ON

30 seconds DIP switch 4 OFF – DIP switches 5, 6 ON

90 seconds DIP switch 4 ON – DIP switch 5 OFF – DIP switch 6 ON

3 minutes DIP switches 4, 5 OFF – DIP switch 6 ON

20 minutes DIP switches 4, 5 ON – DIP switch 6 OFF

30 minutes DIP switches 4, 5, 6 OFF

Adjust the range of detection by

moving the positions of the DIP

switches as advised below

(this information is also printed on the

LED Board above the DIP switches);

Note: Up is ON, Down is OFF.

Adjust the ON time by moving the

positions of the DIP switches as

advised below;

Noted item:

1.This product must be installed or dismantled by qualified electrician.

2.The driver is placed inside, and its input voltage is 220-240V/AC,50/60Hz.

3.Please make sure the power is off before installing and maintenance, and check

the power cable is properly connected before switching on the lamp.

4.Always obey the fire code, and make sure the lamp has at least 7.5cm space to

ventilate.

5.Don't install the lamp on inflammable, sloping, or damaged surface.

6.Never clean the lamp with dump cloth when the lamp is switched on.

To Customers:

Thank you for purchasing our goods.

Please read the manual before using, and keep it for reference.

Installing instruction:

1.Unscrew the installing plate from the lamp and disconnect the wires on the

terminal block.

2.Connect the utility supply to terminal block (L for live wire, N for null wire) on the

installing plate, then fix the installing plate on the ceiling or wall by screws.

3.Connect the wires from lamp to the terminal block and combine the installing

plate with the lamp by rotating.

Special attention:

1.Don't dismantle the lamp or unscrew the led broad, otherwise it will affect the

heat dissipation, and reduce the lifespan of the led ceiling light.

2.If you have any question about the product, please consult our professional

engineers.

Adjustable Microwave

USER MANUAL

Add: No.16 Ind. Road, Xiaolan Ind. Zone, Xiaolan Town, Zhongshan,G.D., China

Contact e-mail: [email protected]

Website:

www.hanrun-lighting.com

5ETGY*QNGU

6GTOKPCN$NQEM

Open the cover to adjust the microwave setting.

Add: No.16 Ind. Road, Xiaolan Ind. Zone, Xiaolan Town, Zhongshan,G.D., China

Contact e-mail: [email protected]

Website:

www.hanrun-lighting.com

• The ‘Daylight Sensor’ setting determines the level of darkness required

for the luminaire to start operating.

• Once you have adjusted the luminaire to the desired settings, fit the plastic lens

cover back in to place followed by the bezel.

• Secure them both using the 4 fixing screws previously removed.

• Re-connect the luminaire to the back plate using steps 4.8 & 4.9,

as detailed in section 4. Installation.

• Switch the power to the luminaire ON.

Disable DIP switches 7, 8, 9 ON

50 Lux DIP switches 7, 8 ON – DIP switch 9 OFF

30 Lux DIP switch 7 ON – DIP switch 8 OFF – DIP switch 9 ON

10 Lux DIP switch 7 OFF – DIP switches 8, 9 ON

5 Lux DIP switches 7, 8, 9 OFF

Adjust the LUX level by moving the

positions of the DIP switches as

advised below;

Note: 50 Lux and 30 Lux is twilight

operation, 10 Lux and 5 Lux is

darkness operation only. ‘Disable’

means the luminaire will switch ON

when motion is detected regardless

of the ambient light level.

7. Emergency Mode & Internal Battery

• When power is switched ON, the green LED indicator will immediately

illuminate confirming mains power is present, and the internal battery will begin

to charge. The luminaire will also go through its ‘warm up’ period as detailed

in section 6. Setting Up & Testing.

Note: the internal battery will take 24 hours to fully charge.

• When power is cut, the luminaire automatically switches into emergency mode.

The green LED indicator will turn OFF. The luminaire will immediately turn

ON, running at 50% output using the internal battery (for 3 hours when fully

charged). The microwave sensor will cease to function during this period

of time.

• Once power is restored, the luminaire will once again go through its ‘warm up’

period. The green LED indicator will turn ON when mains power is present.

• The battery will begin to re-charge, and the luminaire will be running at full

output each time the microwave sensor is activated.

3 Year Guarantee

In the unlikely event of this product becoming faulty due to defective material or

manufacture within 3 years of the date of purchase, please return it to your supplier

in the first year with proof of purchase and it will be replaced free of charge.

For years 2 and 3 or any difficulty in the first year, telephone the helpline

on 020 8450 0515.

Note: A proof of purchase is required in all cases. For all eligible replacements (where

agreed by Timeguard) the customer is responsible for all shipping/postage charges

outside of the UK. All shipping costs are to be paid in advance before a replacement

is sent.

Zerofour – January 2017

67.058.568 (Issue 1)

Timeguard Limited.

Victory Park, 400 Edgware Road,

London NW2 6ND

Sales Office: 020 8452 1112

or email csc@timeguard.com

For a product brochure please contact:

If you experience problems, do not immediately return the unit

to the store. Telephone the Timeguard Customer Helpline;

Qualified Customer Support Co-ordinators will be on-line

to assist in resolving your query.

HELPLINE

020 8450 0515

or email helpline@timeguard.com

www.timeguard.com

Timeguard LEDMRQ18WHEMMS Operating instructions

Timeguard LEDMRQ18WHEMMS Operating instructions

Timeguard LEDMRQ18WHEMMS Operating instructions

Related papers

Other documents