Catalina Lighting 20565-000 Installation guide

Brand
Catalina Lighting
Model
20565-000
Type
Installation guide
Thank you for purchasing The Backer
5/6-inch Recessed Retrofit with integrated
SwitchSense® technology. The Backer is
designed to contribute to a safer environment
and provide light where you need it during
power outages.
Installation
Package
Contents
Feature &
Function
1) Socket Adapter Assembly ----------------1 Piece
2) Retrofit Trim -----------------------------------1 Piece
Model#: 20565-000
The Backer 5/6-inch Recessed Retrofit with
SwitchSense® technology is designed to
be your ultimate battery back-up supply that
you can place in any existing 5-inch or
6-inch recessed canister within your home.
The Backer will provide up to 90 minutes of
continuous power delivering 200+ lumen
output on a full charge. During a power
outage, The Backer uses stored energy
from the NiMH battery to power the LED
system. The SwitchSense® technology
allows you to turn on The Backer using your
wall switch as you normally would. When
main power returns, The Backer returns to
normal operation and will automatically
start re-charging for the next time battery
power is needed.
How To
Works
FIG. 1
FIG. 5
FIG. 2 FIG. 4
FIG. 3
OR
Important! Up to four (4) Backer 5/6-inch
Recessed Retrofits may be installed on a
single wall switch circuit. Exceeding four
(4) units on a single switch circuit may
interfere with the SwitchSense® system
to recognize a power failure at the main
household circuit panel.
Step 1: Remove The Backer main housing /
trim from the box and make sure that no
parts are missing. Included with your
purchase is a standard Socket Adapter
Assembly with quick-connect male-end plug
and Retrofit Trim with butterfly clips and
quick-connect female-end plug.
Step 2: The Backer 5/6-inch Recessed
Retrofit includes a factory installed NiMH
battery. The unit is shipped with the battery
circuit in the OFF position. Prior to installing
The Backer into an existing 5 or 6 inch
canister, move the toggle switch to the ON
position to initiate the normal operating setup
(see Figure 1). This will insure that the
battery supply is now active and will send
battery supply to the LED system during
power outages and be able to receive power
from the house circuit for re-charging.
Step 3: Where applicable, it may be
necessary to remove an existing socket
bracket from the canister. Follow the steps in
Figure 2 to remove the socket bracket by
unscrewing the wing nut inside the canister
and detaching the socket from the socket
bracket. A list of applicable housing canisters
is provided in the Warning section.
Warning! Prior to beginning
any installation please turn
the power OFF at the Circuit
Panel and Wall Switch.
USE AND CARE GUIDE
Step 4: Thread the Socket Adapter Assembly
into the canister socket as shown in Figure 3.
Step 5: Plug the quick-connect male-end from
the Socket Adapter Assembly into the
female-end of the Retrofit Trim as shown in
Figure 4.
Step 6: Carefully squeeze together the butterfly
clips and insert into the holes or clips of the
existing canister as shown in Figure 5.
Step 7: Make sure all wires from the Socket
Adapter Assembly and Retrofit Trim are inside
the existing canister and carefully push the
Retrofit Trim upward into the canister. In some
existing shallow canisters you may need to
position the existing socket and Socket Adapter
Assembly adjacent to the side of the plastic
battery housing.
Important! Once the Installation is complete
restore power at the Circuit Panel.
Self-charging battery backup supply.
The backer switches to the battery backup
when power goes out.
50,000 hour LED performance.
90+ minutes battery supply at 200 lumens on
full charge.
PARTS
SOCKET ADAPTER
ASSEMBLY
RETROFIT TRIM
Specifications
FCC statements
Manufacturer warrants all of its lighting fixtures
against defects in materials and workmanship for
one (1) year from the date of original purchase.
This warranty does not cover parts becoming
defective due to misuse, accidental damage,
improper handling and/or installation and
specifically excludes liability for indirect, incidental
orconsequential damages. Product found to be
defective may or may not be replaced with same
or like type product, contingent on the nature of
the defect, and or replacement availability and/or
compensated for at a pro-rated value. Some
states do not allow limitations on how long an
implied warranty lasts, and/or the exclusion or
limitation of incidental or consequential damages,
so the above limitations or exclusions may not
apply to you. This warranty gives you specific
rights and you may also have other rights, which
vary from state to state. Proof of purchase is
required to exercise the warranty.
The Backer is designed to provide 200+
lumens at 90 minutes on a full charge.
Normal charge time is approximately 11-13
hours.
Chart 1 shows the relationship between
battery charge time and battery support. The
NiMH battery can be fully recharged up to
500 times providing many years of reliable
service!
During Idle Time (when The Backer is OFF)
the backup battery is continually monitoring
the potential power outage occurance.
Chart 2 shows the relationship between Idle
Time and battery support time. It is
suggested to install The Backer in a location
that is considered active with regular
intervals of normal usage.
Warning
For Customer Service assistance:
www.evolutionlightingllc.com
MADE IN CHINA
MIN. 5 in
5 in 6 in.
COMPATIBLE HOUSING
DIMENSIONS
This lamp has been tested and found to comply
with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment on and off, the user is encouraged to
try to correct the interference by one or more of
the following:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the lighting
unit and receiver.
3. Connect the lighting unit into an outlet on a
circuit other than the outlet which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV
technician for assistance.
NOTE: Please note that changes and
modifcations not expressly approved by the party
responsible for
compliance could void the user's authority to
operate the equipment.
Battery Caution and Disposal
1. Do not dispose of The Backer in a fire or
where excessive heat may be present.
2. The Backer NiMH battery should be recycled
or disposed of as per State and Local guidelines.
Limited
Warranty
Please read carefully and save these
instructions as you may need them at a later
date.
WARNING- RISK OF FIRE OR ELECTRIC
SHOCK
1. FOR USE WITH HOUSING MODELS:
INCANDESCENT HOUSINGS –
COMMERCIAL ELECTRIC C7IC, C7ICR,
C7ICA, C7ICRA, C7, C7R, C7S,
HBR5000SIC; HALO H7ICT, H7RICT, H7ICAT,
H7RICAT, H7T, H7RT, H27ICT, H27T,
H27RT, H750ICAT, H750RICAT; ELCO
EL7ICA, EL7RICA; JUNO IC22, IC22R;
THOMAS PS1, PS1-RM; DMF DH6ICATQ,
DH6ICRATQ; NORA NHIC-17QAT,
NHRIC-17QAT; ELITE B6IC, B6RIC;
SEA GULL 11018, 11028. HALO LED
HOUSINGS – H750ICAT, H750RICAT.
2. INSTALLATION OF THIS RETROFIT KIT
REQUIRES A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE
LUMINAIRE’S ELECTRICAL SYSTEM AND
THE HAZARD INVOLVED. IF NOT
QUALIFIED, DO NOT ATTEMPT
INSTALLATION. CONTACT A QUALIFIED
ELECTRICIAN.
3. INSTALL THIS KIT ONLY IN THE
LUMINAIRE THAT HAS THE
CONSTRUCTION FEATURES AND
DIMESIONS SHOWN IN THE
PHOTOGRAPHS AND/OR DRAWINGS AND
WHERE THE INPUT RATING OF THE
RETROFIT KIT DOES NOT EXCEED THE
INPUT RATING OF THE LUMINAIRE.
4. WARNING – TO PREVENT WIRING
DAMAGE OR ABRASION, DO NOT EXPOSE
WIRING TO EDGES OF SHEET METAL OR
OTHER SHARP OBJECTS.
5. THIS RETROFIT KIT IS ACCEPTED AS A
COMPONENT OF A LUMINAIRE WHERE
THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY AUTHORITIES
HAVING JURISDICTION. PRODUCT MUST
BE INSTALLED BY A QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH THE
APPLICABLE AND APPROPRIATE
ELECTRICAL CODES. THE INSTALLATION
GUIDE DOES NOT SUPERSEDE LOCAL OR
NATIONAL REGULATIONS FOR
ELECTRICAL INSTALLATIONS.
6. DO NOT MAKE OR ALTER ANY OPEN
HOLES IN AN ENCLOSURE OF WIRING OR
ELECTRICAL COMPONENTS DURING KIT
INSTALLATION.
7. THIS DEVICE IS NOT INTENDED FOR
USE WITH EMERGENCY EXITS.
8. DO NOT USE THE BACKER WITH A
DIMMING CIRCUIT.
90
90min
100%
60
30
60min
(30%)
(82%)
(60%)
0
8
30min
16
36
25
Idle Time (days not in use)
Battery support
time(min)
13
90min
8
60min
11
30min
0
Battery charge time (hours)
Battery support
time (min)
90
100%
60
30
(30%)
(82%)
(60%)
Chart 1
Chart 2
  • Page 1 1
  • Page 2 2

Catalina Lighting 20565-000 Installation guide

Brand
Catalina Lighting
Model
20565-000
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents