Operating instructions
Clip-on microphone
Item no. 1267829
Intended use
This microphone is designed to convert acoustic signals (sound waves) into electrical signals. It
can be used for announcements and interviews, as a hands-free microphone or for Internet and
multimedia communication. The microphone can be secured to clothing with a clip. The low-level
audio output signal must only be connected to suitable microphone inputs on audio devices.
Contact with moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged. In
addition, improper use can cause hazards such as short circuiting, re, electric shock etc. Read
the instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
This product complies with the statutory national and European requirements. All company names
and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Microphone
• Clamp
• Windscreen
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on proper
handling in this manual, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• When using the product, make sure that the cable is not pinched, kinked or damaged
by sharp edges.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modications and repairs are to be performed exclusively by an
expert or at a qualied shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Operation
The product must only be connected to suitable microphone inputs in order to
avoid distortions or mismatches that could cause damage to the microphone or the
connected audio device. Pay attention to the connection values in the "Technical
data".
Never direct the microphone at the sound outlet of loudspeakers, as this can result in
feedback which may damage the loudspeakers and the connected amplier.
a) Securing the microphone
1. Secure the microphone to the user's clothing using the clip so that it is facing the direction of
speech and is not located too far from the mouth. You can attach the microphone to your tie,
collar or other parts of your clothing.
2. Adjust the microphone to the desired speaking position. Ensure that the product sits in a
secure position.
3. You can feed the microphone cable through clothing or holes in accessories.
b) Using the microphone
1. Turn o the audio device to which the microphone will be connected. Turn the sensitivity of
your audio device to zero using the corresponding input level control (refer to the operating
instructions of the audio device you are using).
2. Insert the 3.5 mm jack plug on the microphone cable into the corresponding microphone
connection on your audio device.
3. Turn on your audio device with the connected sound source (loudspeakers).
4. Test the microphone by speaking a few words (e.g. counting whole numbers) whilst slowly
moving the input level control on the audio device upwards until the desired output volume
is reached.
Air movements such as wind, moving the microphone or breathing create deep
frequencies in the sound spectrum. The attached windscreen made of sponge
prevents such sounds from being recorded.
Maintenance and cleaning
• The product does not require maintenance except for occasional cleaning.
• Under no circumstances should you service any of the components in the interior of the device,
therefore never open it.
• Before cleaning, remove the 3.5 mm jack plug from the connected audio device.
• Use a soft, antistatic and lint-free cloth to clean the device. Dust can be removed easily using a
soft and clean long-haired brush and a vacuum cleaner.
• Do not use any abrasive or chemical cleaning materials.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
You thus full your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage.........................................1 – 10 V/DC
Frequency response .................................... 70 Hz - 16000 Hz
Sensitivity ...................................................... -63 dB ±3 dB (0 dB=1 V/µbar at 1000 Hz)
Impedance ....................................................680 Ω ±30 % (at 1000 Hz)
Directivity ......................................................Cardioid
Connection .................................................... 3.5 mm jack plug
Cable length .................................................. 1.45 m
Operating conditions ................................... -5 to +45 °C, <85 % RH
Storage conditions.......................................-20 to +60 °C, <95 % RH
Dimensions (Ø x H).......................................13 x 24 mm
Weight ............................................................ 25 g
Frequency response
Directivity
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE. V1_1114_02-DS
1
2
3
4
Renkforce TCM-141 Owner's manual
Renkforce PM58 Handheld Microphone (vocals) Owner's manual
Speaka Professional 1082615 Operating Instructions Manual
Mc crypt FXM-4200 USB/2 Operating Instructions Manual
Conrad 76 89 86 Operating Instructions Manual
Conrad Components BRC34M Audio recording unit Component Recording Time 20 s Operating instructions
VOLTCRAFT SL-10 Operating Instructions Manual
Art Tube MP Studio V3 Operating instructions