Page is loading ...
SHARK
Wireless Charger - in Car or at home
Installation Guide:
(1) Package includes:
FRONT
BACK
12 V Car Adaptor
Fuse box wiring cable
Installation Guide
Main Unit
(2) Installation:
inCarBite representatives are ready to help you with any questions about your new product. We can guide
you through first time installation, simply follow below steps. We wish you to start enjoying your purchase
right away!
Select a vertical location, ideally the edge of center console (the
middle storage compartment between the front two seats of a car),
avoid air vent area or stick on the glass of vehicle or air bag that may
cause accident. To achieve best result, fully clean the edge with
Alcohol Pad, leave dry and ensure no dust is left behind. Peel off 3M
sticker on Velcro of Charger; ensure the shark mouth of charger on the
top, apply the Velcro by pressing firmly with 5KG force at least 10
seconds into place ensuring full contact over the entire area. Charger
will stay firmly after few minutes.
(A) Simple installation: DIY
Get power from the Cigarette Lighter:
Simply plug in the car adaptor to the car cigarette power hole and connect the other end to the charger IN
Hole.
(B) Professional installation: Fuse Box Wiring cable
Get power from the Fuse Box:
You can also connect the cable directly to your car’s Fuse Box if you prefer not to use your cigarette lighter.
So you need the provided long cable for internal wiring that you can neatly tuck away around to Fuse Box so
as to install it in the most discreet way possible.
Connect the extension wire with the main unit wire plug, installing the wire to Fuse Box.
Open the Fuse Box and choose the right Fuse slot and take out the fuse. Plug the fuse to our adaptor at
the end or the wire and then plug the adaptor to the same right Fuse slot.
Close the Fuse Box.
Check your car’s user manual to find the correct setup.
Wireless charger instruction:
1. Make sure your “Shark” is plugged in and your car is power on.
2. To charge mobile, simply put your mobile into “Shark” mouth / slot in vertical position, ensure front side of
mobile phone facing rear side of “Shark”. “Shark” large contact surface design will ensure accurate
charging.
3. BLUE LED: ON - Mobile being charged
OFF - Standby Mode
Important Notice:
Do not place the product under strong sunlight for long to avoid overheating.
Do not keep the product near the fire, exposed to rain, liquid or excessive moisture; unplug the product
if any of the mentioned conditions exist.
Ensure no objects which may cause strong interference or metal objects are placed near the product.
This product is neither fire-resistant nor acid-resistant.
Do not wash the product with any chemicals, soaps or detergents.
Do not put the battery or the phone without “receiver” and other electronic products on the charging
slot directly.
During charging, the product, the contact part between rubber skin and charging cradle may become
warm during normal use. It will keep below 45OC or 110OF, if it exceed, the matched phone will stop
charging. The phone will cool down to normal temperature gradually after it is fully charged. Always
allow adequate ventilation around the product and use care when handling.
If the problems of over-voltage, over-current or high machine-temperature occur in the process of
charging, charging will stop temporarily to avoid damages to the charger. When it resumes normal,
the charging will restart.
When the phone is fully charged, the phone can be used properly after 15 seconds.
Working environment: Temperature: 0-50OC(32-122OF)；Humidity: 45-95RH%
Product Specifications:
CHARGER INPUT : DC 12 V / 3 A
CHARGER OUTPUT : DC 5V / 1 A
Two USB Port : 2 A each port to charge other mobile devices in car
Optional Kit:
For Home Use: 1 x Home Power Adaptor + 1 x Desktop Stand
Universal Wireless Charger Receiver
iPhone Case with built-in Wireless Charger Receiver MFi Certification : iPhone 5 / iPhone 6, 6S / iPhone 6 plus, 6S plus
PATENT PENDING
/
