PR LED Studio 3500D User manual

Brand: PR

Model: LED Studio 3500D

Category: Floodlights

Type: User manual

This manual is also suitable for

LED Studio 3500T

PR LED Studio 3500D is a lighting fixture designed for indoor use only. It features 12x10W LED lights with a lifespan of 50,000 hours. The fixture offers two channel modes - 1CH (1 channel) and 4CH (4 channels) - and the DMX start address can be set by the user to ensure proper communication with a controller. The fixture also has a dimmer function for adjusting the light intensity from 0 to 100%. With a beam angle ranging from 0° to 80°, the PR LED Studio 3500D provides flexible lighting options for various applications.

LED Studio 3500D

LED Studio 3500T

PR-3500D

PR-3500T

This product manual contains important information about the safe installation and use of this lighting fixture.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/12

INDEX

SAFE USAGE OF THE LIGHTING FIXTURE

INSTALLING THE LIGHTING FIXTURE

CONTROL SYSTEM AND POWER CONNECTIONS

DMX TERMINATOR

SETUP OPTIONS- LIGHTING FIXTURE CONFIGURATION

TO SET THE DMX START ADDRESS

OPERATION MENU

DMX PROTOCOL

INDICATION OF LED DISPLAY

MAINTENANCE

TROUBLESHOOTING

TECHNICAL DATA

ELECTRICAL DIAGRAM

COMPONENT ORDER CODES

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst

every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The

publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition

before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused

by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the lighting fixture

Name Quantity Unit Remark

Clamp 2 Pcs

Safety cord 2 Pcs

5-pin XLR Plug(Female) 1 Pc

5-pin XLR Plug(male) 1 Pc

User’s Manual 1 pc

SAFE USAGE OF THE LIGHTING FIXTURE

When unpacking and before disposing of the carton, check there is no transportation damage before using the lighting fixture.

there

be any damage caused by transportation, consult your dealer and do not use the apparatus.

The lighting fixture can be only used indoors, IP20.

The lighting fixture is not designed or intended to be mounted directly on to inflammable surfaces.

The

lighting fixture is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is

Avoid direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the lighting fixture in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation,

ensure that the voltage and frequency of power supply match the power requirements of the lighting fixture.

It is essential that each lighting fixture is correctly earthed and that electrical installation conforms to all relevant sta

Do not conne

ct this device to any other types of dimmer apparatus.

Make sure that the power-

cord is never crimped or damaged by sharp edges. Never let the

Only handle the power-

cord by the plug. Never pull out the plug

When the lighting fixture is hanged to a high place, please use a safety cord provided to pass through the lighting fixture’s

secondary safety fixing for safety seasons. For details, refer to “INSTALL THE LIGHTING

Exterior surface temperatures of the lighting fixture after 5 minutes operation is 45

There is no user serviceable parts inside the lighting fixture, do not open the housing and never operate

covers removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Always disconnect the fixture

from power, before

3/12

SAFE USAGE OF THE LIGHTING FIXTURE

When unpacking and before disposing of the carton, check there is no transportation damage before using the lighting fixture.

be any damage caused by transportation, consult your dealer and do not use the apparatus.

The lighting fixture can be only used indoors, IP20.

The lighting fixture is not designed or intended to be mounted directly on to inflammable surfaces.

lighting fixture is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is

2m. 2m

Avoid direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the lighting fixture in any way.

Electrical connection must only be carried out by qualified personnel.

ensure that the voltage and frequency of power supply match the power requirements of the lighting fixture.

It is essential that each lighting fixture is correctly earthed and that electrical installation conforms to all relevant sta

ct this device to any other types of dimmer apparatus.

cord is never crimped or damaged by sharp edges. Never let the

power-

cord come into contact with other cables.

cord by the plug. Never pull out the plug

by tugging the power-cord.

When the lighting fixture is hanged to a high place, please use a safety cord provided to pass through the lighting fixture’s

secondary safety fixing for safety seasons. For details, refer to “INSTALL THE LIGHTING

FIXTURE “section.

Exterior surface temperatures of the lighting fixture after 5 minutes operation is 45

℃

, when achieving steady state it is

There is no user serviceable parts inside the lighting fixture, do not open the housing and never operate

the lighting fixture with the

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

from power, before

installation, cleaning and

any maintenance work !

When unpacking and before disposing of the carton, check there is no transportation damage before using the lighting fixture.

Should

ensure that the voltage and frequency of power supply match the power requirements of the lighting fixture.

It is essential that each lighting fixture is correctly earthed and that electrical installation conforms to all relevant sta

ndards.

cord come into contact with other cables.

When the lighting fixture is hanged to a high place, please use a safety cord provided to pass through the lighting fixture’s

handles as a

FIXTURE “section.

, when achieving steady state it is

65℃.

the lighting fixture with the

any maintenance work !

4/12

INSTALL THE LIGHTING FIXTURE

When the lighting fixture is used, as the right figure above, unfold the support to certain angle and put the lighting fixture onto a

flat surface. Make sure it is steady.

When the lighting fixture is used at a high place, as the left figure above, fold the support, turn it round to the top of the lighting

fixture, connect a lamp hook to the mounting hole reserved in the support by screws, and then hang the hook to a high place.

Eventually, use the safety cord provided to pass through the handles and hang it as a second safety fixing.

CONTROL SYSTEM AND POWER CONNECTION

Connection between the controller and a lighting fixture and between one lighting fixture and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Please use the lighting fixture’s cannon 5- pin signal input and

output cables as connection. The 5-pin signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not

connected in any way. The device accepts digital control signals in protocol DMX512 (1990).

As for power connections, each lighting fixture has to be supplied separately by external power. Use the power cord of each lighting

fixture to connect the mains power directly, making sure the voltage and frequency marked on the panel of the lighting fixture match

what is supplied.

5/12

The connections are as the figure below.

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last lighting fixture in the chain. The connections are illustrated below.

6/12

SETUP OPTIONS-LIGHTING FIXTURE CONFIGURATION

To browse through or change a fixture’s configuration, after

ENTER button has been

pressed for about 3 seconds, the display of

AddR means the entrance of the menu. To set or browse through a fixture’s settings, press buttons of UP and DOWN. After

button ENTER is pressed, a sub-menu is entered showing current parameters while indication flashing.

Press button UP or

DOWN to change values(plus or minus)

Press button

ENTER

to save your settings or enter into the upper level menu and the indication stops from flashing.

Press

FUNC to enter into the upper level menu(parameters not saved )or browse through the upper level menu.

After FUNC is pressed for more than 1second or buttons not pressed for more than 1 minute, it will go back to the main menu

displaying the fixture’s name.

After the exit of the menus, the current lamp color will be shown.

While DMX signals are available, Signal LED indication will be on, otherwise off..

TO SET THE DMX START ADDRESS

Each device must be given a DMX start address so that the correct lighting fixture responds to the correct control signals. This DMX

start address is the channel number from which the lighting fixture starts to “listen” to the digital control information being sent out

from the controller. The device has Two Channel Modes. 1 Channel Mode has 1 channel, so set the No. 1 lighting fixture’s address

001, No. 2 lighting fixture’s address 002, No. 3 lighting fixture’s address 003, and so on. 4 Channel Mode has 4 channels, so set the No.

1 lighting fixture’s address 001, No. 2 lighting fixture’s address 005, No. 3 lighting fixture’s address 009, and so on.

Launch the lighting fixture. Press button ENTER for more than 3 seconds to unlock the panel till

is displayed

Press button FUNC, UP or DOWN to find “ ” menu.

Then press ENTER to show DMX address and press UP or DOWN to set DMX address.

At this time, the address will flash continuously. Press button ENTER to confirm and it means the setting has been

enabled and saved. After powered next time, the latest setting will be used.

Press button FUNC, it will return to the upper menu one by one.

7/12

DMX PROTOCOL

1 Channel Mode

Channel FUNCTION DMX DESCRIPTION

1 Dimmer 000-255 Dimming

4 Channel Mode

Channel

FUNCTION

DMX

DESCRIPTION

1 The first part Dimmer 000-255 Dimming

2 The second part Dimmer 000-255 Dimming

3 The third part Dimmer 000-255 Dimming

4 The forth part Dimmer 000-255 Dimming

INDICATION OF LED CHARACTER

DMX Indication

On DMX signal OK

Off No DMX signal

8/12

MAINTENANCE

To prolong the life of the lighting fixture, it is very important to do the maintenance work. Cooling fans must be cleaned once every

15days and external lens cleaned periodically for an optimum light output. DO NOT USE ANY SOLVENT CONTAINING

CHEMICAL ELEMENT.

Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning products should be

used for cleaning with care. It is recommended to clean lighting fixture at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

TROUBLESHOOTING

PROBLEM ACTION

The lighting fixture doesn’t switch on

 Power connection is not correct.

 Power supply is damaged or abnormal. Call a qualified personnel to fix

it.

 Connection of control board is not correct. Call a qualified personnel to

fix it.

The lighting fixture can be turned on, but LEDs

do not emit light and are out of control.

 Connection of LED board is not correct. Call a qualified personnel to fix

it.

The lamp comes on but the lighting fixture

doesn’t respond to the controller

 Make sure that the lighting fixture’s Start Address is properly set.

 Replace or repair the XLR signal cable.

The beam appears dim  The lighting fixture is too hot. Take ventilation measures to make it cool.

9/12

TECHNICAL DATA

VOLTAGES:

100-240V AC，50/60Hz

POWER CONSUMPTION:

120W@220V

LED Light sources :

Quantity 12 pcs(10Wx12)

Manufacturers Rated LED Life 50000 Hours

DIMMER:

0-100% linearly adjustable

COLOR TEMPERATURE

PR-3500T 3200K

PR-3500D 5600K

CRI

Ra≥86

Luminous Flux

5000 lm

LIGHT ANGLE

Field Angle(

1/10 Maximum) θ 0°~80°

CONTROL:

DMX512, 5 pin interfaces

Two

Channel Modes:

1 CH,1

Channel;4CH,4 Channels.

HOUSING:

Extruding aluminum, IP20

WORK ENVIRONMENT TEMPERATURE:

-20°C~40°C

WEIGHT:

Net weight: 4.2kg

Gross weight: 6.8 kg

10/12

SIZES:

300±20

185

1800

Electrical Diagram

11/12

COMPONENT ORDER CODES

NAME PART NO. QUANTITY REMARK

Power Switch

192010134

10W LED White

150020255

CT3200K for PR

00T

10W LED White

15002025

CT5500K for PR

00D

PR-3500 Control Board(W)

230060

309

12/12

PR LIGHTING LTD.

PR New Hi-tech Science Park, 1582 Xingye Avenue

Nancun Panyu, Guangzhou, 511442 China

TEL: +86-20-3995 2888

FAX: +86-20-3995 2330

P/N: 320020125A

Version:20140711

PR LED Studio 3500D User manual

Brand: PR

Model: LED Studio 3500D

Category: Floodlights

Type: User manual

This manual is also suitable for

LED Studio 3500T

Download PDF

report

PR LED Studio 3500D User manual

This manual is also suitable for

PR LED Studio 3500D User manual

Related papers

Other documents