Advantech PCA-6773-R0A1 User manual

PCA-6773

ISA Intel ULV400,650/LV800, 933

Slot PC, CPU/VGA/LCD/LVDS/

LAN/CFC and PC/104

User’s Manual

PCA-6773 User’s Manual ii

Copyright

nal manufacturer reserves the right to make improvements to the products

described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmit-

ted in any form or by any means without the prior written permission of

the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer

assumes no responsibility for its use, nor for any infringements upon the

rights of third parties that may result from such use.

Acknowledgements

Award is a trademark of Award Software International, Inc.

VIA is a trademark of VIA Technologies, Inc.

IBM, PC/AT, PS/2 and VGA are trademarks of International Business

Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows® is a registered trademark of Microsoft Corp.

RTL is a trademark of Realtek Semi-Conductor Co., Ltd.

ESS is a trademark of ESS Technology, Inc.

UMC is a trademark of United Microelectronics Corporation.

SMI is a trademark of Silicon Motion, Inc.

Creative is a trademark of Creative Technology LTD.

All other product names or trademarks are properties of their respective

owners.

For more information on this and other Advantech products, please visit

our websites at: http://www.advantech.com

http://www.advantech.com/epc

For technical support and service, please visit our support website at:

http://service.advantech.com.tw/eservice/

This manual is for the PCA-6773.

Part No.200K677310

2 nd Edition, Nov, 2004

iii

Packing List

Before you begin installing your card, please make sure that the following

materials have been shipped:

• 1 PCA-6773 all-in one single board computer

• 1 startup manual

• 1 CD-ROM or disks for utility, drivers, and manual (in PDF format)

• 1 power cable p/n:1703080101

• 1 PS/2 KB/M cable p/n:1700060202

• 1 COM port cable p/n:1701140201

• 1 FDD cable p/n:1701340705

• 1 EIDE cable p/n:170140060A

• Mini Jumper p/n:1653302122

If any of these items are missing or damaged, contact your distributor or

sales representative immediately.

Optional Item:

1703100260 USB cable adapter(2.00mm)

PCA-6773 User’s Manual iv

Model No. List Description

PCA-6773F-J0A1 ISA Celeron ULV400 Slot PC

VGA/LCD/LVDS/LAN/CFC/PC104

PCA-6773-MOA1 ISA Celeron ULV650 Slot PC

VGA/LCD/LVDS/LAN/CFC/PC104

PCA-6773-R0A1 ISA Intel LV933 Slot PC

VGA/LCD/LVDS/2LAN/CFC/PC104

Additional Information and Assistance

Visit the Advantech web site at www.advantech.com where you can find

the latest information about the product.

Step 1. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version, application

software, etc.)

• A complete description of the problem

• The exact wording of any error messages

v

FCC

This device complies with the requirements in

part 15 of the FCC rules: Operation is subject to

the following two conditions:

1.This device may not cause harmful interfer-

ence, and

2. This device must accept any interference

received, including interference that may cause

undesired operation

This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These lim-

its are designed to provide reasonable protection

against harmful interference when the equipment

is operated in a commercial environment. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instruction manual,

may cause harmful interference to radio commu-

nications. Operation of this device in a residential

area is likely to cause harmful interference in

which case the user will be required to correct

the interference at his/her own expense. The

user is advised that any equipment changes or

modifications not expressly approved by the

party responsible for compliance would void the

compliance to FCC regulations and therefore,

the user's authority to operate the equipment.

Caution!

Achtung!

There is a danger of a new battery exploding if it

is incorrectly installed. Do not attempt to

recharge, force open, or heat the battery.

Replace the battery only with the same or equiv-

alent type recommended by the manufacturer.

Discard used batteries according to the manufac-

turer’s instructions.

PCA-6773 User’s Manual vi

vii

Contents

Chapter 1 General Information ........................................1

1.1 Introduction ....................................................................... 2

1.2 Features ............................................................................. 2

1.3 Specifications .................................................................... 3

1.4 Board layout: dimensions.................................................. 5

Chapter 2 Installation ........................................................7

2.1 Jumpers.............................................................................. 8

2.2 Connectors......................................................................... 8

2.3 Locating Connectors(component side)........................... 10

2.4 Locating Connectors(solder side).................................... 11

2.5 Setting Jumpers ............................................................... 12

2.6 Clear CMOS (JP1) .......................................................... 13

2.7 RS232/422/485 Select(J1)............................................... 14

2.8 Watchdog timer configuration ........................................ 14

2.9 Installing DIMMs............................................................ 15

2.10 ATX power control connector (CN24) ........................... 15

2.11 Printer port connector (CN5)........................................... 16

2.12 CompactFlash Card Connector ....................................... 16

2.13 Floppy drive connector (CN4) ........................................ 16

2.14 Primary IDE connector(CN3) ......................................... 17

2.15 VGA/LCD interface connections .................................... 18

2.16 USB connectors (CN9,CN25)......................................... 19

2.17 Ethernet configuration..................................................... 20

2.18 Power connectors (CN19, FAN1) ................................... 20

2.19 HDD ,PWR LED Connector & WDT output(CN6) ....... 20

2.20 COM port connector (CN20,CN21)................................ 21

2.21 Keyboard and PS/2 mouse connector (CN26) ................ 21

2.22 External KB/Mouse Connector(CN23)........................... 21

2.23 Audio AC97 interface(CN12) ......................................... 21

2.24 IR Connector(CN13)....................................................... 21

Chapter 3 Software Configuration .................................23

3.1 Introduction ..................................................................... 24

3.2 VGA display firmware configuration ............................. 24

Figure 3.1:VGA setup screen........................................ 25

Chapter 4 PCI SVGA Setup ............................................27

4.1 Introduction ..................................................................... 28

4.1.1 Chipset .......................................................................... 28

4.1.2 Display memory............................................................ 28

PCA-6773 User’s Manual viii

4.1.3 Display types................................................................. 28

4.2 Installation of the SVGA Driver ..................................... 29

4.2.1 Installation for Windows 95 ......................................... 29

4.2.2 Installation for Windows 98/Me ................................... 33

4.2.3 Installation for Windows NT ........................................ 38

4.2.4 Installation for Windows 2000 ..................................... 43

4.2.5 Installation for Windows XP ........................................ 48

4.3 Further Information......................................................... 54

Chapter 5 PCI Bus Ethernet Interface...........................55

5.1 Introduction ..................................................................... 56

5.2 Installation of Ethernet driver ......................................... 56

5.2.1 Installation for MS-DOS and Windows 3.1.................. 56

5.2.2 Installation for Windows 98 ......................................... 56

5.2.3 Installation for Windows 2000 ..................................... 60

5.2.4 Installation for Windows NT ........................................ 65

5.3 Further information ......................................................... 71

Chapter 6 Award BIOS Setup.........................................73

6.1 System test and initialization........................................... 74

6.1.1 System configuration verification................................. 74

6.2 Award BIOS setup .......................................................... 75

6.2.1 Entering setup .............................................................. 75

Figure 6.1:BIOS setup program initial screen .............. 75

6.2.2 Standard CMOS Features setup.................................... 76

Figure 6.2:CMOS Features setup.................................. 76

6.2.3 Advanced BIOS Features setup .................................... 77

Figure 6.3:Advanced BIOS Features setup................... 77

6.2.4 Advanced Chipset Features setup ................................. 78

Figure 6.4:Advanced Chipset Features setup ............... 78

6.2.5 Integrated Peripherals ................................................... 79

Figure 6.5:Integrated Peripherals.................................. 79

6.2.6 Power Management Setup ............................................ 79

Figure 6.6:Power Management Setup........................... 79

6.2.7 PnP/PCI Configurations................................................ 80

Figure 6.7:PnP/PCI Configurations .............................. 80

6.2.8 PC Health Status ........................................................... 80

Figure 6.8:PC Health Status.......................................... 80

6.2.9 Frequency/Voltage Control........................................... 81

Figure 6.9:Frequency/Voltage Control ......................... 81

6.2.10 Load Optimized Defaults.............................................. 82

Figure 6.10:Load BIOS defaults screen........................ 82

6.2.11 Set Password ................................................................. 82

Figure 6.11:Set password.............................................. 83

6.2.12 Save & Exit Setup......................................................... 84

Figure 6.12:Save to CMOS and EXIT.......................... 84

ix

6.2.13 Exit Without Saving...................................................... 85

Figure 6.13:Quit without saving ................................... 85

Appendix A Programming the Watchdog Timer .............87

A.1 Supported Input Timing Modes ...................................... 88

Appendix B Installing PC/104 Modules ............................91

B.1 Installing PC/104 Modules.............................................. 92

Appendix C Pin Assignments .............................................95

C.1 ATX suspend power connector (CN24).......................... 96

C.2 Floppy connector (CN4).................................................. 97

C.3 Primary IDE Connector (CN3) ....................................... 98

C.4 CompactFlash connector(CN28)..................................... 99

C.5 LAN,RJ45 connector(CN18) ........................................ 100

C.6 USB1, 2 connector(CN25) ............................................ 100

C.7 USB 3, 4 connector(CN9) ............................................. 101

C.8 IR connector(CN13)...................................................... 101

C.9 LCD INV power connector(CN8)................................. 102

C.10 LCD Backlight connector(CN7) ................................... 102

C.11 DIO connector(CN15)................................................... 103

C.12 HDD, PWR LED connector & WDT output( CN6) ..... 103

C.13 LVDS connector(CN10) ............................................... 104

C.14 LPT connector(CN5)..................................................... 105

C.15 Extension Panel Connector (CN11) .............................. 106

C.16 COM 1, 2 Connector (CN21, CN20) ............................ 106

C.17 Audio I/F connector(CN12) .......................................... 107

C.18 D-SUB VGA connector(CN16) .................................... 107

C.19 Negative power input connector(CN22) ....................... 108

C.20 Keyboard and Mouse connector(CN26) ....................... 108

C.21 EXT_KB/Mouse connector(CN23)............................... 109

C.22 Main power connector (CN19) ..................................... 109

C.23 LCD connector(CN14).................................................. 110

C.24 PWR_SW connector(CN1) ........................................... 111

C.25 Reset connector(CN2) ................................................... 111

C.26 CPU Fan connector (FAN1).......................................... 111

Appendix D System Assignments .....................................113

D.1 System I/O Ports............................................................ 114

Table D.1 System I/O ports .......................................114

D.2 1st MB memory map..................................................... 115

Table D.2 1st MB memory map................................ 115

D.3 DMA channel assignments............................................ 115

Table D.3 DMA channel assignments ........................115

D.4 Interrupt assignments .................................................... 116

PCA-6773 User’s Manual x

Table D.4 Interrupt assignments................................. 116

1 Chapter 1 General Information

1

General Information

This chapter gives background

information on the PCA-6773.

Sections include:

• Introduction

• Features

• Specifications

• Board layout and dimensions

CHAPTER

PCA-6773 User’s Manual 2

Chapter 1 General Information

1.1 Introduction

PCA-6773 is a new standard ISA bus Half-sized SBC. With an Onboard

Intel ULV Celeron 400/650 Fanless CPU or LV Pentium III800(optional)/

933MHz processor, along with a VIA VT8606/TwiserT + VT82C686B

system chipset. The PCA-6773 support SDRAM up to 512MB, with an

optional SODIMM then memory can support up to 1 GB.

Other on-board features include an EIDE, FDD, LPT, 4USBs, and 2 serial

ports(RS-232 and RS-232/422/485).Watchdog timer & IrDA suppport, as

well as a 10/100Mbps Ehernet is provided. The SSD solution supports

Type I/II CompactFlash cards.

This product uses a VIA TwisterT chip with Integrated Savage4 2D/3D/

Video Accelerator and supports 4X AGP VGA/LCD interface and up to

8/16/32 MB frame buffer using system memory. 9/12/18/24/36 bit TFT is

also supported. PCA-6773 supports AC97 audio with the addition of the

optional PCM-231A-00A1 audio module.

Its dimension is follow standard ISA slot PC, this make it can match with

all half-sized chasis and can operate in high vibration enviorment.

1.2 Features

• Intel ULV 400, 650/LV800(optional), 933 MHz CPU on-board

• On board PCI SVGA VGA/LCD display

• 4X AGP graphics for high performance applications

• Low power consumption, requires no CPU cooling

fan(ULV400,650)

• 10/100 Mbps Ethernet

• Supports boot from USB device

• Supports wake-on-LAN

• Supports Ring-up by Modem

• Supports LCD backlight turn-off function

• RS-485 Auto-flow

3 Chapter 1 General Information

1.3 Specifications

1.3.1 Standard SBC Functions

• CPU: On board Intel ULV 400,650/LV800(optional), 933 MHz CPU

• System chipsets: VIA VT8606"TwisterT"+VT82C686B

• BIOS: Award 256 KB Flash memory

• System memory: SDRAM SODIMMx1, MAX:512MB(optional:

SODIMMx2, up to 1GB)

• 2nd cache memory: Celeron ULV 400, 650: 256K

P-III LV 800, 933: 512K

• SSD: Support CompactFlash, Card Type I/II

• Watchdog Timer: 1~62 Sec, System reset or IRQ11

• Expansion Interface: 1x16-bit ISA Slot, 1x PC/104 connector

• Battery: Lithium 3/V/196 mAH

• Serial ports: Two serial RS-232 ports

COM1: RS-232 COM2: RS-232/422/485

RS-485 suppports AUTO-flow

• USB: 4 USB ports, USB 1.1 compliant

1.3.2 VGA/LCD Interface

• Chipset: VIA VT8606"TwisterT" chip with integrated Savage4 2D/3D/

Video Accelerator

• Frame buffer: Supports 8/16/32MB frame buffer with system memory

• Interface: 4X AGP VGA/LCD interface, Support up to 36 bit TFT

• Display modes:

CRT Modes: 1280 x 1024@16bpp (60Hz),

1024 x 768@16bpp (85Hz);

800x600@16bpp(60Hz)

LCD/Simulaneous Modes:

1280 x1024@16bpp (60Hz).

1024 x 768@16bpp (60Hz))

1.3.3 Solid State disk

• Supports CompactFlash Type I/II disks

PCA-6773 User’s Manual 4

1.3.4 PCI bus Ethernet interface

• Chipset: Intel 82551ER, 82551QM(optional),RealTek 8139C(optional)

• Connection: on-board RJ-45

•

BootROM:

build-in-system

• I/O address switchless setting

1.3.5 Mechanical and Environmental

• Dimensions (L x W): 185 x 122 mm(7.3” x 4.8”)

• Power supply voltage: +5 V±5%, +12V ±5%

• Power requirements:

Max:

5A @+5V, 201mA @+12V (with 128MB SDRAM, Intel ULV-400

MHz CPU)

Typical:

2.55 A @ +5V, 48 mA@ +12V(with 128MB SDRAM, Intel ULV-400

MHz CPU)

• Operating temperature: 0 ~ 60°C (32 ~ 140°F),operation

• Operating humidity: 0% ~ 90% Relative Humidity, Non condensing

5 Chapter 1 General Information

1.4 Board layout: dimensions

Figure 1.1: Board layout: dimensions (component side)

PCA-6773 User’s Manual 6

Figure 1.2: Board layout: dimensions (solder side)

7 Chapter 2 Installation

2

Installation

This chapter explains the setup procedures

of PCA-6773 hardware, including instruc-

tions on setting jumpers and connecting

peripherals, switches and indicators. Be

sure to read all safety precautions before

you begin the installation procedure.

CHAPTER

PCA-6773 User’s Manual 8

Chapter 2 Installation

2.1 Jumpers

The PCA-6773 has a number of jumpers that allow you to configure your

system to suit your application. The table below lists the functions of the

various jumpers.

2.2 Connectors

On-board connectors link the PCA-6773 to external devices such as hard

disk drives, a keyboard, or floppy drives. The table below lists the func-

tion of each of the board’s connectors.

Table 2.1: Jumpers

Label Function

JP1 CMOS clear

JP2 Watchdog timer output selection

J1 RS232/422/485 Select

Table 2.2: Connectors

Label Function

CN1 PWR_SW connector

CN2 Reset connector

CN3 Primary IDE connector

CN4 Floppy connector

CN5 LPT connector

CN6 HDD,PWR LED connector&WDT output

CN7 LCD backlight connector

CN8 LCD INV PWR connector

CN9 USB 3,4 connector

9 Chapter 2 Installation

CN10 LVDS connector

CN11 LCD connector

CN12 Audio I/F connector

CN13 IR connector

CN14 LCD connector1

CN15 DIO connector

CN16 D-SUB VGA connector

CN17 PC/104

CN18 LAN connector

CN19 Main power connector

CN20 COM2

CN21 COM1

CN22 Negative power input connector(optional)

CN23 EXT_KB connector

CN24 ATX suspend power connector

CN25 USB 1,2 connector

CN26 Keyboard/Mouse connector

CN28 CF connector

Table 2.2: Connectors

PCA-6773 User’s Manual 10

2.3 Locating Connectors(component side)

Figure 2.1: Jumper&Connector Locations

Page is loading ...

Advantech PCA-6773-R0A1 User manual

This manual is also suitable for

Advantech PCA-6773-R0A1 User manual

Related papers

Other documents