Advantech PCA-6774 User manual

Brand: Advantech

Model: PCA-6774

Category: PC/workstation barebones

Type: User manual

This manual is also suitable for

PCA-6774FG-00A1

i

PCA-6774

ISA Socket370 Slot PC,

VGA/LCD/LVDS/LAN/CFC

with optional second LAN and

Gigabit LAN

User Manual

PCA-6774 User Manual ii

Copyright

This document is copyrighted, © 2005. All rights are reserved. The origi-

nal manufacturer reserves the right to make improvements to the products

described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmit-

ted in any form or by any means without the prior written permission of

the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer

assumes no responsibility for its use, nor for any infringements upon the

rights of third parties that may result from such use.

Acknowledgements

Award is a trademark of Award Software International, Inc.

VIA is a trademark of VIA Technologies, Inc.

IBM, PC/AT, PS/2 and VGA are trademarks of International Business

Machines Corporation.

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows® is a registered trademark of Microsoft Corp.

RTL is a trademark of Realtek Semi-Conductor Co., Ltd.

ESS is a trademark of ESS Technology, Inc.

UMC is a trademark of United Microelectronics Corporation.

SMI is a trademark of Silicon Motion, Inc.

Creative is a trademark of Creative Technology LTD.

All other product names or trademarks are properties of their respective

owners.

For more information on this and other Advantech products, please visit

our websites at: http://www.advantech.com

http://www.advantech.com/eplatform

For technical support and service, please visit our support website at:

http://www.advantech.com/support

This manual is for the PCA-6774.

Part No. 200K677410

2nd Edition, Dec. 2005

iii

Packing List

Before you begin installing your card, please make sure that the following

materials have been shipped:

• 1 PCA-6774 all-in-one single board computer

• 1 startup manual

• CD-ROM or disks for utility, drivers, and manual (in PDF format)

• 1 Power cable p/n: 1703080101

• 1 PS/2 KB/M cable p/n: 1700060202

• 1 COM port cable p/n: 1700100250

• 1 Printer cable p/n: 1700260250

• 1 FDD cable p/n: 1703340400

• 1 EIDE cable p/n: 1701400452

• Mini Jumper p/n: 1653300100

If any of these items are missing or damaged, contact your distributor or

sales representative immediately.

Optional item:

1700100170 USB cable adapter (2.54 mm)

Model No. List Description

PCA-6774F-00A1 ISA Socket 370 half-sized CPU Card with

VGA/LCD/LVDS/LAN/CFC

PCA-6774FG-00A1 ISA Socket 370 half-sized CPU card with

VGA/LCD/LVDS/Giga LAN/CFC

PCA-6774F-02A1 ISA Eden 400 half-sized CPU card with

VGA/LCD/LVDS/2LAN/CFC

PCA-6774 User Manual iv

Additional Information and Assistance

1. Visit the Advantech web site at www.advantech.com where you can

find the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's customer

service center for technical support if you need additional assistance.

Please have the following information ready before you call:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version, application

software, etc.)

• A complete description of the problem

• The exact wording of any error messages

v

Caution!

Achtung!

This device complies with the requirements in part

15 of the FCC rules: Operation is subject to the fol-

lowing two conditions:

1.This device may not cause harmful interference,

and

2.This device must accept any interference

received, including interference that may cause

undesired operation.

This equipment has been tested and found to com-

ply with the limits for a Class A digital device, pursu-

ant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is oper-

ated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance

with the instruction manual, may cause harmful

interference to radio communications. Operation of

this device in a residential area is likely to cause

harmful interference in which case the user will be

required to correct the interference at his/her own

expense. The user is advised that any equipment

changes or modifications not expressly approved

by the party responsible for compliance would void

the compliance to FCC regulations and therefore,

the user's authority to operate the equipment.

There is a danger of a new battery exploding if it is

incorrectly installed. Do not attempt to recharge,

force open, or heat the battery. Replace the battery

only with the same or equivalent type recom-

mended by the manufacturer. Discard used batter-

ies according to the manufacturer’s instructions.

PCA-6774 User Manual vi

vii Table of Contents

Contents

Chapter 1 Introduction ......................................................2

1.1 Introduction ....................................................................... 2

1.2 Features ............................................................................. 2

1.3 Specifications .................................................................... 3

1.3.1 Standard SBC Functions................................................. 3

1.3.2 VGA/LCD Interface ....................................................... 3

1.3.3 Solid State disk ............................................................... 4

1.3.4 PCI bus Ethernet interface .............................................. 4

1.3.5 Mechanical and Environmental ...................................... 4

1.4 Board layout: dimensions.................................................. 5

Figure 1.1:Board layout: dimensions (component side)...5

Figure 1.2:Board layout: dimensions (solder side)......... 6

Chapter 2 Installation ........................................................8

2.1 Jumpers.............................................................................. 8

Table 2.1:Jumpers........................................................... 8

2.2 Connectors......................................................................... 8

Table 2.2:Connectors...................................................... 8

2.3 Locating Connectors (component side)........................... 10

Figure 2.1:Jumper & Connector locations.................... 10

2.4 Locating Connectors (solder side)................................... 11

Figure 2.2:Connectors (solder side).............................. 11

2.5 Setting Jumpers ............................................................... 11

2.6 Clear CMOS (J1)............................................................. 13

Table 2.3:CMOS clear (J1)........................................... 13

2.7 COM2 RS232-422-485 Select (J3) ................................. 14

Table 2.4:COM2 RS232-422-485 Select...................... 14

2.8 Watchdog timer configuration ........................................ 14

2.8.1 Watchdog timer output option (J2)............................... 14

Table 2.5:Watchdog timer output option (J2)............... 14

2.9 Installing DIMMs............................................................ 15

2.10 ATX power control connector (CN20,CN21)................. 16

2.10.1 ATX feature connector (CN20) and soft-on power button

connector (CN21).............................................................16

Figure 2.3:Wiring for ATX soft power switch function16

2.11 Printer port connector (CN4)........................................... 17

2.12 CompactFlash Socket...................................................... 17

2.12.1 CompactFlash (CN5) .................................................... 17

2.13 Floppy drive connector (CN3) ........................................ 17

2.13.1 Connecting the floppy drive ......................................... 17

2.14 IDE connector (CN1,CN2).............................................. 18

PCA-6774 User Manual viii

2.14.1 Connecting the hard drive............................................. 18

2.15 VGA/LCD interface connections .................................... 19

2.15.1 CRT display connector (CN7) ...................................... 19

2.15.2 Flat panel display connector (CN22)............................ 19

2.15.3 Extension flat panel connector (CN23) ........................ 19

2.15.4 LVDS LCD panel connector (CN25) ........................... 19

2.15.5 Panel type selection (SW1)........................................... 20

Table 2.6:S1 Panel Type Select (SW1) ........................ 20

2.16 USB connectors (CN6).................................................... 20

2.17 Ethernet configuration..................................................... 21

2.17.1 100Base-T connector (CN8)......................................... 21

2.17.2 Network boot ................................................................ 21

2.18 Power connectors (CN14, CN15).................................... 21

2.18.1 Main power connector, +5 V, +12 V (CN15)............... 21

2.18.2 CPU Fan power supply connector (CN14)................... 21

2.19 ATX Power & HDD LED, speaker out Connector......... 22

2.19.1 HDD LED (CN19)........................................................ 22

2.19.2 ATX power LED & KB-LOCK (CN16) ...................... 22

2.19.3 Speaker out (CN17) ...................................................... 22

2.20 COM port connector (CN9,CN10,CN29) ....................... 22

2.21 Keyboard and PS/2 mouse connector (CN11) ................ 22

2.22 External KB/mouse connector (CN12) ........................... 22

2.23 Watchdog output (CN18) ................................................ 23

2.24 Daughter card connector (CN27,CN28).......................... 23

Chapter 3 Software Configuration .................................26

3.1 Introduction ..................................................................... 26

3.2 VGA display firmware configuration ............................. 26

Figure 3.1:VGA setup screen........................................ 27

Chapter 4 Award BIOS Setup.........................................30

4.1 System test and initialization........................................... 30

4.1.1 System configuration verification................................. 30

4.2 Award BIOS setup .......................................................... 31

4.2.1 Entering setup ............................................................... 31

Figure 4.1:BIOS setup program initial screen .............. 31

4.2.2 Standard CMOS Features setup.................................... 32

Figure 4.2:CMOS Features setup.................................. 32

4.2.3 Advanced BIOS Features setup .................................... 33

Figure 4.3:Advanced BIOS Features setup................... 33

4.2.4 Advanced Chipset Features setup ................................. 34

Figure 4.4:Advanced Chipset Features setup ............... 34

4.2.5 Integrated Peripherals ................................................... 35

Figure 4.5:Integrated Peripherals.................................. 35

4.2.6 Power Management Setup ............................................ 35

ix Table of Contents

Figure 4.6:Power Management Setup........................... 35

4.2.7 PnP/PCI Configurations................................................ 36

Figure 4.7:PnP/PCI Configurations .............................. 36

4.2.8 PC Health Status ........................................................... 36

Figure 4.8:PC Health Status.......................................... 36

4.2.9 Frequency/Voltage Control........................................... 37

Figure 4.9:Frequency/Voltage Control ......................... 37

4.2.10 Load Optimized Defaults.............................................. 38

Figure 4.10:Load BIOS defaults screen........................ 38

4.2.11 Set Password ................................................................. 38

4.2.12 Save & Exit Setup......................................................... 39

4.2.13 Exit Without Saving...................................................... 40

Chapter 5 PCI SVGA Setup ............................................42

5.1 Introduction ..................................................................... 42

5.1.1 Chipset .......................................................................... 42

5.1.2 Display memory............................................................ 42

5.1.3 Display types................................................................. 42

5.2 Installation of the SVGA Driver ..................................... 43

5.2.1 Installation for Windows 95 ......................................... 43

5.2.2 Installation for Windows 98/Me ................................... 47

5.2.3 Installation for Windows NT ........................................ 52

5.2.4 Installation for Windows 2000 ..................................... 57

5.2.5 Installation for Windows XP ........................................ 62

5.3 Further Information......................................................... 68

Chapter 6 PCI Bus Ethernet Interface...........................70

6.1 Introduction ..................................................................... 70

6.2 Installation of Ethernet driver ......................................... 70

6.2.1 Installation for MS-DOS and Windows 3.1.................. 70

6.2.2 Installation for Windows 98 ......................................... 71

6.2.3 Installation for Windows 2000 ..................................... 74

6.2.4 Installation for Windows NT ........................................ 79

6.3 Further information ......................................................... 85

Appendix A Programming the Watchdog Timer .............88

A.1 Supported Input Timing Modes ...................................... 88

Appendix B Pin Assignments .............................................92

B.1 Primary IDE Connector (CN1) ....................................... 92

Table B.1:Primary IDE Connector (CN1) .................... 92

B.2 Secondary IDE Connector (CN2) ................................... 93

Table B.2:Secondary IDE Connector(CN2) ................. 93

B.3 Floppy Connector (CN3)................................................. 94

Table B.3:Floppy Connector (CN3) ............................. 94

B.4 Printer Port Connector (CN4) ......................................... 95

Table B.4:Printer Port Connector (CN4) ...................... 95

PCA-6774 User Manual x

B.5 CompactFlash Socket (CN5)........................................... 96

Table B.5:CompactFlash Socket (CN5) ....................... 96

B.6 USB Connector (CN6) .................................................... 97

Table B.6:USB Connector (CN6)................................. 97

B.7 D-SUB VGA Connector (CN7) ...................................... 98

Table B.7:D-SUB VGA Connector (CN7)................... 98

B.8 LAN RJ45 Connector (CN8)........................................... 98

Table B.8:LAN RJ45 Connector (CN8) ....................... 98

B.9 COM Port 1, 2 Connector (CN9, CN10)......................... 99

Table B.9:COM Port 1 Connector (CN9, CN10) ......... 99

B.10 PS/2 Keyboard & Mouse Connector (CN11).................. 99

Table B.10:PS/2 Keyboard & Mouse Connector.......... 99

B.11 External Keyboard Connector (CN12).......................... 100

Table B.11:External Keyboard Connector (CN12) .... 100

B.12 CPU Fan Connector (CN14) ......................................... 100

Table B.12:CPU FAN Connector (CN14).................. 100

B.13 EBX Power Connector (CN15)..................................... 101

Table B.13:EBX Power Connector (CN15) ............... 101

B.14 Power LED & Keyboard Lock (CN16)......................... 102

Table B.14:Power LED & Keyboard Lock (CN16) ... 102

B.15 External Speaker (CN17) .............................................. 102

Table B.15:External Speaker (CN17)......................... 102

B.16 Reset Connector (CN18) ............................................... 103

Table B.16:Reset Connector (CN18).......................... 103

B.17 HDD LED Connector (CN19)....................................... 103

Table B.17:HDD LED Connector (CN19) ................. 103

B.18 ATX Feature Connector (CN20)................................... 104

Table B.18:ATX Feature Connector (CN20) ............. 104

B.19 ATX Soft-on Power Button Connector (CN21)............ 104

Table B.19:ATX Soft-on Power Button Connector.... 104

B.20 LCD 40-Pin Connector (CN22) .................................... 105

Table B.20:LCD 40-Pin Connector (CN22)............... 105

B.21 LCD 20-Pin Connector (CN23) .................................... 106

Table B.21:LCD 20-Pin Connector (CN23)............... 106

B.22 LCD Backlight Connector (CN24) ............................... 106

Table B.22:LCD Backlight Connector (CN24) .......... 106

B.23 LVDS Connector (CN25).............................................. 107

Table B.23:LVDS Connector (CN25) ........................ 107

B.24 I/O Daughter Board Connector 1 (CN27)..................... 108

Table B.24:I/O Daughter Board Connector 1 (CN27) 108

B.25 I/O Daughter Board Connector 2 (CN28)..................... 109

Table B.25:I/O Daughter Board Connector 2 (CN28) 109

B.26 RS485/422 Connector (CN29) ..................................... 109

Table B.26:RS485/422 Connector (CN29)................. 109

xi Table of Contents

Appendix C System Assignments .....................................112

C.1 System I/O Ports............................................................ 112

Table C.1:System I/O ports ........................................ 112

C.2 1st MB memory map..................................................... 113

Table C.2:1st MB memory map ................................. 113

C.3 DMA channel assignments............................................ 114

Table C.3:DMA channel assignments ........................ 114

C.4 Interrupt assignments .................................................... 115

Table C.4:Interrupt assignments ................................. 115

PCA-6774 User Manual xii

1 Chapter 1

1

General Information

This chapter gives background

information on the PCA-6774.

Sections include:

• Introduction

• Features

• Specifications

• Board layout and dimensions

CHAPTER

PCA-6774 User Manual 2

Chapter 1 Introduction

1.1 Introduction

Advantech's new PCA-6774 is a Socket 370 half-sized CPU card that will

support up to 1.26GHz Pentium III with 512KB 2nd cache using VIA

VT8606 "Twister T" chipset. This SBC includes a 4X AGP controller, a

PCI Ethernet interface, and 36-bit TTL interface. Its design is based on

the half-sized CPU card and supports ISA bus expansion. Other on-board

features include an FDD, LPT, 2 USBs (4 USBs optional), and 2 serial

ports. The SSD solution supports CompactFlash cards. This product uses

a VIA Twister T chip with Integrated ProSavage4 2D/3D/Video Acceler-

ator and supports 4X AGP VGA/LCD interface and up to 8/16/32 MB

frame buffer using system memory. With the selection of daughter

boards, the PCA-6774 board can support a second LAN at 10/100Mbps,

also this CPU card can support Gigabit LAN with Intel 82540.

1.2 Features

• Supports Socket 370 for Intel processors up to Pentium III 1.26GHz

with 512KB (Tualatin)

• ISA bus half-sized CPU card

• Supports selectable LAN (1 x 10/100BASE-T LAN or 2 x 10/

100BASE-T LAN or 1 x Gigabit LAN)

• 4X AGP graphics for high performance applications

• Supports boot from USB device

• Supports wake-on-LAN

• Supports Ring-up by Modem

• Supports LVDS interface

• Supports LCD backlight turn-off function

• RS-485 Auto-flow

3 Chapter 1

1.3 Specifications

1.3.1 Standard SBC Functions

• CPU: Supports Socket 370 for Intel processors up to Pentium III 1.26

GHz with 512KB cache (Tualatin)

• System chipsets: VIA VT8606 "Twister T" + VT82C686B

• BIOS: Award 256 KB Flash memory

• System memory: One DIMM socket accepts 64 MB up to 512 MB

SDRAM

• 2nd cache memory: 128/256/512KB on Celeron/PentiumIII processor

• Enhanced IDE interface: One channel supports up to two EIDE

devices. Supports ATA-100, ATA-33 and PIO modes.

• FDD interface: Supports up to two FDDs

• Serial ports: Two serial RS-232 ports:

COM1: RS-232

COM2: RS-232/422/485

RS-485 supports AUTO-flow

• Parallel port: Parallel port supports SPP/EPP/ECP modes

• Keyboard/mouse connector: Supports standard PC/AT keyboard and a

PS/2 mouse

• Power management: Supports power saving mode including Normal/

Standby/Suspend modes. APM 1.2 compliant

• Watchdog timer: 62 level timer intervals

• USB: Two universal serial bus ports, Optional 4 ports.

1.3.2 VGA/LCD Interface

• Chipset: VIA VT8606 "Twister T" chip with integrated ProSavage4

2D/3D/Video Accelerator

• Frame buffer: Supports 8/16/32MB frame buffer with system memory

• Interface: 4X AGP VGA/LCD interface, Supports for up to 36 bit TFT

• Display modes:

CRT Mode: 1280 x 1024@16bpp (60Hz),

1024 x 768@16bpp (85Hz),

PCA-6774 User Manual 4

LCD/Simultaneous Mode:

1280 x 1024@16bpp (60Hz),

1024 x 768@16bpp (60Hz),

1280 x 1024@32bpp

LVDS interface:

Supports 2-Channel (2 x 18-bit) LVDS interface

1.3.3 Solid State disk

• Supports CompactFlash Type I/II disks

1.3.4 PCI bus Ethernet interface

• Chipset: Intel 82551/82559/82540

• Ethernet interface: IEEE 802.3u compatible 10/100Base-T interface.

Supports selectable LAN (1 x 10/100base-T LAN or 2 x 10/100base-T

LAN or 1x Gigabit LAN)

• I/O address switchless setting

1.3.5 Mechanical and Environmental

• Dimensions (L x W): 185 x 122 mm(7.3” x 4.8”)

• Power supply voltage: +5 V, +12V ±5%

• Power requirements:

Max:

6.18 A @ +5 V, 0.22 A @+12 V

Typical:

5.5 A @ +5 V, (with PC133 128MB SDRAM, Pentium III 1.0 GHz)

0.17 A @ +12 V, (with PC133 128MB SDRAM, Pentium III 1.0 GHz)

• Operating temperature: 0 ~ 60°C (32 ~ 140°F)

• Operating humidity: 0% ~ 90% Relative Humidity, Non condensing

• Weight: 0.27 kg (weight of total package)

5 Chapter 1

1.4 Board layout: dimensions

Figure 1.1: Board layout: dimensions (component side)

PCA-6774 User Manual 6

Figure 1.2: Board layout: dimensions (solder side)

7 Chapter 2

2

Installation

This chapter explains the setup procedures

of PCA-6774 hardware, including instruc-

tions on setting jumpers and connecting

peripherals, switches and indicators. Be

sure to read all safety precautions before

you begin the installation procedure.

CHAPTER

PCA-6774 User Manual 8

Chapter 2 Installation

2.1 Jumpers

The PCA-6774 has a number of jumpers that allow you to configure your

system to suit your application. The table below lists the functions of the

various jumpers.

2.2 Connectors

Onboard connectors link the PCA-6774 to external devices such as hard

disk drives, a keyboard, or floppy drives. The table below lists the func-

tion of each of the board’s connectors

.

Table 2.1: Jumpers

Label Function

J1 CMOS clear

J2 Watchdog timer output selection

J3 COM2 RS232-422-485 Select

Table 2.2: Connectors

Label Function

CN1 Primary IDE Connector

CN2 Secondary IDE Connector

CN3 Floppy Connector

CN4 Printer Port Connector

CN5 CompactFlash Socket

CN6 USB Port 1, 2

CN7 D-SUB VGA Connector

CN8 LAN RJ45 Connector

CN9 COM Port 1

CN10 COM Port 2

CN11 PS/2 Keyboard & Mouse Connector

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Advantech PCA-6774 User manual

Brand: Advantech

Model: PCA-6774

Category: PC/workstation barebones

Type: User manual

This manual is also suitable for

PCA-6774FG-00A1

Related papers

Other documents