Harmonic ChannelPort 8100/8200 Reference guide

Harmonic
Brand
Harmonic
Model
ChannelPort 8100/8200
Type
Reference guide
Spectrum™ ChannelPort™ 8100/8200 Module Quick Reference Guide
+7 495 506 5981 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland)
Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA),
16
45
Up to two ChannelPort modules can be installed in a MediaPort 7000 or a MediaDeck 7000 chassis. (Sample slot configuration shown.)
MediaDeck 7000/MediaPort 7000 Chassis Rear Panel
ChannelPort 8100 Standard Channel
ChannelPort 8100 Enhanced Channel
Ethernet Port LEDs
Activity Status
RS-422 Port LEDs
StatusStatus
13. Soft Power button (middle)
14. Status/Wink LED (bottom)
15. GPIO/RS-422 connector
16. RS-422 Port
17. Ethernet (used only in MediaDeck 7000)
18. Ethernet (used only in MediaPort 7000)
1. External IN 1 Channel A
2. OUT (Primary or HD-branded*) Channel A
3. OUT (Secondary or SD-branded) Channel A
4. External IN 1 Channel B
5. OUT (Primary or HD-branded) Channel B
6. OUT (Secondary or SD-branded) Channel B
7. AES Audio IN Channel A
8. LTC OUT Channel A
9. AES Audio IN Channel B
10. LTC OUT Channel B
11. Reference IN
12. Reference Loop
* “HD/SD-branded” refers to Independent Branding mode.
15
1
Unused
2 3 4 5 6
13
8910 11 12
14
1
716 17 18
Unused
2 3 4 5 6
13
8910 11 12
14
1
7
15
16 17 18
13. Soft Power button (middle)
14. Status/Wink LED (bottom)
15. GPIO/RS-422 connector
16. RS-422 Port
17. Ethernet (used only in MediaDeck 7000)
18. Ethernet (used only in MediaPort 7000)
1. External IN 1/Key
2. OUT (Primary or HD-branded*)
3. OUT (Secondary or SD-branded)
4. External IN 2/Fill
5. OUT (Clean Primary**)
6. OUT (Clean Secondary)
7. AES Audio IN
8. LTC OUT
9. Unused
10. Unused
11. Reference IN
12. Reference Loop
* “HD/SD-branded” refers to Independent Branding mode.
** “Clean Primary/Secondary” refers to video output with no graphics or overlays.
Power Supplies and LEDs Module A: ChannelPort 8100 Module or MediaPort 7000 Module Module B: ChannelPort 8200 Module
Ethernet Port LEDs
Activity Status
RS-422 Port LEDs
StatusStatus
28-0374 Rev. E Page 1
28-0374 Rev. E Page 2
+7 495 506 5981 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland)
Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA),
ChannelPort 8200 Standard Channel
Unused
15
16 17
123456 7 8
910 11 12 13 14 18 19 20
15. Soft Power button (middle)
16. Status/Wink LED (bottom)
17. GPIO/RS-422 connector
18. RS-422 Port
19. Ethernet (used only in MediaDeck 7000)
20. Ethernet (used only in MediaPort 7000)
1. External IN 1 Channel A
2. External IN 2/OUT (if OUT, Primary) Channel A
3. OUT (Secondary or SD-branded*) Channel A
4. OUT (Primary or HD-branded) Channel A
5. External IN 1 Channel B
6. External IN 2/OUT (if OUT, Primary) Channel B
7. OUT (Secondary or SD-branded) Channel B
8. OUT (Primary or HD-branded) Channel B
9. AES Audio IN Channel A
10. LTC OUT Channel A
11. AES Audio IN Channel B
12. LTC OUT Channel B
13. Reference IN
14. Reference Loop
* “HD/SD-branded” refers to Independent Branding mode.
Ethernet Port LEDs
Activity Status
RS-422 Port LEDs
StatusStatus
ChannelPort 8200 Enhanced Channel
* “HD/SD-branded” refers to Independent Branding mode.
** “Clean Primary/Secondary” refers to video output with no graphics or overlays.
Unused
15
16 17
123456 7 8
910 11 12 13 14 18 19 20
15. Soft Power button (middle)
16. Status/Wink LED (bottom)
17. GPIO/RS-422 connector
18. RS-422 Port
19. Ethernet (used only in MediaDeck 7000)
20. Ethernet (used only in MediaPort 7000)
1. External IN 1/Key 1
2. External IN 2/Fill 1
3. External IN 3/OUT (if OUT, Secondary or SD-branded*)
4. OUT (Primary or HD-branded)
5. External IN 4/Key 2
6. External IN 5/Fill 2
7. External IN 6/OUT (if OUT, Clean Secondary**)
8. OUT (Clean Primary/Secondary or SD-branded)
9. AES Audio IN
10. LTC OUT
11. Unused
12. Unused
13. Reference IN
14. Reference Loop
Notes:
• Connections 1-8 use DIN 1.0/2.3 connectors.
• See “ChannelPort 8200 Enhanced Channel Mode Configurations”
on page 4 for configuration options.
Ethernet Port LEDs
Activity Status
RS-422 Port LEDs
StatusStatus
Notes:
• Connections 1-8 use DIN 1.0/2.3 connectors.
• See “ChannelPort 8200 Standard Channel Mode Configurations”
on page 4 for configuration options.
1. From the rear of the MediaPort 7000 or MediaDeck 7000,
unscrew the two lock screws that secure the filler panel and
remove the filler panel.
1
Caution: Do not use the two lock screws on the rear panel of the module
to pull it into position. Tighten the screws only after the module is
fully inserted.
4. If installing two modules, repeat steps 1-3 for the
second module.
For complete installation instructions, refer to the Spectrum
System Installation and Hardware Reference Guide.
3. Tighten the two lock screws on the rear of the module
to secure it to the chassis.
2
3
2. Grasp the module handle and push firmly into the
slot. Ensure the module is fully inserted by pressing
on the connectors with the palm of your hand.
+7 495 506 5981 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland)
Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA),
Installing the ChannelPort Module
Note: The DB-9 male-to-male extension
cables and the GPIO cable in this diagram
are customer supplied. The RJ-45-to-DB-9
cable is supplied by Harmonic.
For graphics control automation, automation can use the Oxtel protocol over IP or over serial RS-422. All automation systems differ in their array of
control connectors and methods of interfacing with the ChannelPort. The following diagram is one example.
Connecting the ChannelPort Module to an Automation System
Play 1
Graphics 1 Graphics 2
Play 2
422
(3)
422
(4)
422
(1)
422
(2)
GPIO/RS-422 Signal Assignments
9 8 7 6 5 4
18 17
16 15 13 12 11 10
26 25
24 23 22
21 20 19
13 2
14
Function
RX (-/+)
TX (-/+)
GPIO/RS-422 Signals
Function
Pin
Ground
Ground
18
Serial
0
2-3
GPIO 0
19
GPIO 1
20
Serial 1
GPIO 2
21
GPIO 3
22
Serial 2
GPIO 4
23
GPIO 5
24
Serial 3
GPIO 6
25
GPIO 7
26
8-9
10-11
16-17
1
6-7
4-5
14-15
12-13
The ChannelPort module has a female GPIO/RS-422 connector that can be used
to control players or graphics. For more information on configuring GPIO using
SystemManager, refer to “ChannelPort Configuration” in the SystemManager User Guide.
28-0374 Rev. E Page 3
+7 495 506 5981 (Russia, CIS), +81 3 5565 6737 (Japan), +86 10 8391 3313 (China, mainland)
Harmonic Technical Support: +888 673 4896 (Americas), +65 6542 0050 (Asia Pacific), + 44 1252 555 450 (EMEA),
ChannelPort 8200 Standard Channel Mode Configurations
The ChannelPort 8200 module offers eight DIN 1.0/2.3 connectors for video input and output. The following table shows
the possible connector configurations for Standard Channel mode.
Configuration
DIN 1
DIN 2
DIN 3
DIN 4
DIN 6
DIN 7
DIN 8
Standard
Channel (SC) 1
External Input 1
(Channel A)
Out, Primary
(Channel A)
Out, Secondary
(Channel A)
Out, Primary
(Channel A)
(Channel B)
Out, Primary
(Channel B)
Out, Secondary
(Channel B)
Out, Primary
(Channel B)
Standard
Channel (SC) 2
External Input 1
(Channel A)
External Input 2
(Channel A)
Out, Secondary
(Channel A)
Out, Primary
(Channel A)
(Channel B)
External Input 2
(Channel B)
Out, Secondary
(Channel B)
Out, Primary
(Channel B)
ChannelPort 8200 Enhanced Channel Mode Configurations
The ChannelPort 8200 module offers eight DIN 1.0/2.3 connectors for video input and output. The following table shows
the possible connector configurations for Enhanced Channel mode.
Configuration
DIN 1
DIN 2
DIN 3
DIN 4
DIN 5
DIN 6
DIN 7
DIN 8
Enhanced
Channel (EC) 1
External Input 1/
Key 1
External Input 2/
Fill 1
Out, Secondary
Out, Primary
External Input 4/
Key 2
External Input 5/
Fill 2
External Input 6
Out, Clean
Primary
Enhanced
Channel (EC) 2
External Input 1/
Key 1
External Input 2/
Fill 1
Out, Secondary
Out, Primary
External Input 4/
Key 2
External Input 5/
Fill 2
Out, Clean
Secondary
Out, Clean
Primary
Enhanced
Channel (EC) 3
External Input 1/
Key 1
External Input 2/
Fill 1
External Input 3
Out, Primary
External Input 4/
Key 2
External Input 5/
Fill 2
External Input 6
Out, Secondary
28-0374 Rev. E Page 4
The ChannelPort 8100/8200 provides a number of licensed features including support for SD, HD, MPEG-2, DV, VC-3,
four or eight graphics layers, ProRes, and support for an Emergency Alert System (EAS). For information on licensed
features, refer to "ChannelPort Module Reference" in the Spectrum Installation and Hardware Reference Guide.
Model
Number
MPEG-2
DV/DVCPRO
AVC-Intra VC-3 ProRes
Play
Play
Play
Play
Play
CPT-8100
X
X
X
X
X
CPT-8200
X
X
X
X
X
The following table shows available ChannelPort 8000 Series module options.
Supported Codecs for the ChannelPort Module
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Harmonic ChannelPort 8100/8200 Reference guide

Harmonic
Brand
Harmonic
Model
ChannelPort 8100/8200
Type
Reference guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents