McQuay M5WM 007G User manual

McQuay
Brand
McQuay
Model
M5WM 007G
Category
Split-system air conditioners
Type
User manual
MWM - G - 2005
Wall Mounted Split Systems
Models: MWM 007G/GR
 MWM 009G/GR
 MWM 010G/GR
 MWM 015G/GR
 MWM 020G/GR
 MWM 025G/GR

 M5WM 007G/GR
 M5WM 009G/GR
 M5WM 010G/GR
 M5WM 015G/GR
 M5WM 020G/GR
 M5WM 025G/GR

Note : Installation and maintenance are to be performed only by qualified personnel who are
familiar with local codes and regulations, and experienced with this type of equipment.
Caution: Sharp edges and coil surfaces are a potential injury hazard. Avoid contact with them.
Warning : Moving machinery and electrical power hazard. May cause severe personal
injury or death. Disconnect and lock off power before servicing equipment.
"McQuay" is a registered trademark of McQuay International. All rights reserved throughout the world.
c
2005 McQuay International
"Bulletin illustrations cover the general appearance of McQuay International products at the time of publication
and we reserve the right to make changes in design and construction at any time without notice."
Contents
Features ........................................................................................................................ 1
Specifications ............................................................................................................... 3
Performance Table ...................................................................................................... 15
Noise Level .................................................................................................................. 35
Operating Range ......................................................................................................... 38
Refrigeration Cycle Diagram ...................................................................................... 39
Outlines And Dimension ............................................................................................. 44
Wiring Diagrams .......................................................................................................... 50
Safety Precautions Before Installation ...................................................................... 71
Special Precautions For R407C.................................................................................. 73
Special Precautions For R410A.................................................................................. 75
Installation ................................................................................................................... 77
Remote Controller Operation Guide .......................................................................... 87
Special Function .......................................................................................................... 89
Servicing And Maintenance ........................................................................................ 92
Troubleshooting ......................................................................................................... 94
Parts List ...................................................................................................................... 96
FF
FF
F
eaea
eaea
ea
turtur
turtur
tur
eses
eses
es
• Easy Installation
- The wall mounted fan coil unit is easily installed because of its compact size, slimness and light weight.
- Slim and short outdoor unit can be easily installed even in a narrow balcony and passageway and yet
have a stable profile.
• Space Saving
- No space is required on either floor or ceiling. This newly developed super slim design for wall mounting
maximizes floor space usage and enhances ceiling appearance where ceilings are low.
• Quiet Operation
- Cooling comfort is improved by whisper-quiet operation which is achieved by a tangential fan.
• Excellent Air Distribution
- Air discharge direction can be adjusted in four directions, manually or automatically by using LCD
remote control.
- The new double louver design with automatic air swing function fully optimizes the room comfort by
distributing the air evenly to the room.
- The unique skew fan design with larger diameter creates better air flow to the operating environment.
• Facilitated Maintenance Ensured
- The new design of air discharge housing whereby the fan blower can be easily accessed by just loosing
two screws on the unit to provides a flexible, faster and easier way to clean up the fan blower and
ionizer.
- Maintenance is easy for electrical components, piping and wiring as these are all easily accessible by
merely removing front plastic panel.
• Wireless Remote Control
- The compact LCD transmitter is able to operate the air conditioner unit within the distance of 9 meters.
- Fan motor speed can be set at low/medium/high or automatic.
- Sleep mode auto control will gradually increase or decrease the setting temperature to provide a
comfortable surrounding for sleeping.
- Air flow direction can be controlled automatically.
- Room temperature is controlled by electronic thermostat.
- The real time timer allows the air conditioner to be switched On and Off automatically based on user
settings.
- Turbo mode function is available to enables the required set temperature to be achieved in a short time.
- Ionizer or non-thermal plasma is available to create better air quality.
- Personalized Setting allows user to preset and store 2 groups of personal settings (including timer
setting) in the handset.
- Auto random restart is a function whereby when there is power failure occurred during operation, the
unit will automatically restart as the last setting condition once the power is resumed.
••
••
• Moisture Removal
- Dry mode with super low indoor fan speed can achieve more affective moisture removal.
- If the room temperature is lower than the set temperature (Cooling mode only), the compressor will cut
out and force on after 9 minutes to remove moisture effectively.
••
••
• 3 Stage Air Purifying Filters
- SARANET air filter is an anti fungus air filter removes comparatively large particles such as dust from
the air.
- TITANIUM OXIDE deodorizer allows long term deodorizing of the air which gives a purer and fresher air
in the room.
- DUAL ACTION ionizer removes any microscopic air particles as small as 0.01 micron.
1
• High Efficiency Heat Exchanger
- The compact design of the 3-fold structure heat exchanger provides a large surface are for better and
efficient heat exchange.
- The unique Hydrophilic slit fin has greatly improved the air flow and the contact surfaces with the air thus
to boost the cooling capacity.
• Rotary Compressor
- The ever popular rotary compressor is more energy efficient and has a higher output to weight ratio.
• Self Diagnosis
- This function is able to detect and to diagnose any faults occurring in the system by blinking of the LED
lights.
- Simplify and ease for troubleshooting.
2
SpecifSpecif
SpecifSpecif
Specif
icaica
icaica
ica
tionstions
tionstions
tions
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
Abbreviation :
INT. O.L.P - Internal Overload Protector
EXT. O.L.P - External Overload Protector
3
R22 Models
(Cooling only)
INDOOR UNIT MWM 009G MWM 010G MWM 015G
OUTDOOR UNIT
MLC 009C MLC 010C MLC 015C
W 2640 2780 3520
Btu/h 9000 9500 12000
INPUT POWER W (50 Hz)
880 837 1100
RUNNING CURRENT A (50Hz) 3.9 3.7 4.9
POWER SOURCE V/Ph/Hz
REFRIGERANT / CONTROL
FAN TYPE
AIR FLOW cfm / L/s
275 / 130 300 / 142 345 / 163
FAN MOTOR 50 Hz 4 POLES X 8W 4 POLES X 9W 4 POLES X 13W
RATED INPUT POWER W (50 Hz)
24 26 29
RATED RUNNING CURRENT A (50 Hz) 0.11 0.11 0.13
FAN MOTOR PROTECTION
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
0.201 / 2.161
HEIGHT mm/in 260 / 10.2
DIMENSION WIDTH mm/in 799 / 31.5
DEPTH mm/in
198 / 7.8
WEIGHT kg/lb 10/22.05
SOUND PRESSURE LEVEL- H / M / L dBA 40 / 35 / 29 39 / 34 / 28 42 / 36 / 29
ROOM TEMPERATURE
AIR DISCHARGE
OPERATION
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in 337 / 13.3
WIDTH mm/in
857 / 33.7
DEPTH mm/in 270 / 10.6
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF 25 30 35
RATED RUNNING CURRENT A 3.6 3.4 4.5
RATED INPUT POWER W
816 759 1012
LOCKED ROTOR AMP. A 18 19 24
PROTECTION DEVICE INT. O.L.P
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
356/14
RATED RUNNING CURRENT A (50 Hz) 0.18 0.23 0.26
MOTOR OUTPUT
W (50 Hz)
20 35 35
RATED INPUT POWER W(50 Hz)
40 52 59
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
0.31/3.40
HEIGHT mm/in
495/19.5
DIMENSION WIDTH mm/in
600/23.6
DEPTH mm/in
245/9.7
WEIGHT kg/lb 28/61.73
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
45 46 49
TYPE
LIQUID mm/in
GAS mm/in
12.70 / 1/2
HEIGHT mm/in 575/22.6
WIDTH mm/in 715/28.1
DEPTH mm/in
330/13.0
REFRIGERANT CHARGE kg/lb 0.64/1.41 0.72/1.59 0.8/1.77
PACKING
DIMENSION
620/24.4
810/31.9
330/13.0
SIZE
6.35 / 1/4
9.52 / 3/8
EG/GI
0.5~2.0
EPOXY POLYESTER POWDER
PIPE
FLARE VALVE
540/21.3
700/27.6
250/9.8
32/70.55
9.52 / 3/8
0.33 / 0.013
FIN
ALUMINIUM (SLIT FIN)
0.11/0.004
1
18
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
0.36/3.94
EXT. O.L.P
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
404/16
957 / 37.7
270 / 10.6
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY HERMETIC
16 / 0.63
SARANET+IONIZER+DEODORIZER
PACKING
DIMENSION
337 / 13.3
CONTROL
THERMOSTAT ELECTRONIC CONTROL
DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
LCD REMOTE CONTROL
198 / 7.8
12/26.46
0.234 / 2.516
260 / 10.2
899 / 35.4
FIN
ALUMINIUM (HYDROPHILIC SLIT FIN TYPE)
0.11 / 0.0043
2
18
SEAMLESS COPPER TUBE
INNER GROOVED
7.0 / 0.276
0.28 / 0.011
MODEL
NOMINAL COOLING CAPACITY
INDOOR UNIT
220-240/1/50
R22 / CAPILLARY TUBE IN OUTDOOR
FAN
THERMAL OVERLOAD RELAY
COIL
TUBE
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
4) ALL SPECIFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
5) SOUND SPECTRUM FOR MWM 020/025G IS NOT READY AT THE TIME OF PRINTING.
Abbreviation :
INT. O.L.P - Internal Overload Protector
4
R22 Models
(Cooling only)
INDOOR UNIT MWM 020G MWM 025G
OUTDOOR UNIT
MLC 020C MLC 025C
W 5569 7034
Btu/h 19000 24000
INPUT POWER W (50 Hz)
1745 2448
RUNNING CURRENT A (50Hz) 7.9 12.3
POWER SOURCE V/Ph/Hz 220-240/1/50
REFRIGERANT / CONTROL
R22 / OUTDOOR CAP. TUBE
FAN TYPE
CROSS FLOW FAN
AIR FLOW cfm / L/s 510 / 240.72 650/306.77
FAN MOTOR 50 Hz 4 POLES X 20W 4 POLES X 25W
RATED INPUT POWER W (50 Hz) 50 69
RATED RUNNING CURRENT A (50 Hz) 0.22 0.29
FAN MOTOR PROTECTION
MATERIAL
COPPER
TUBE PATTERN
GROOVED
DIAMETER mm/in 7.0 / 0.276
THICKNESS mm/in
0.28 / 0.011
MATERIAL
ALUMINIUM
THICKNESS mm/in
0.11 / 0.0043
ROW
2
FIN PER INCH
18
FACE AREA
m
2
/
ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
SOUND PRESSURE LEVEL- H / M / L dBA 44 / 40 /35 49 / 43 / 40
ROOM TEMPERATURE
THERMOSTAT ELECTRONIC CONTROL
AIR DISCHARGE
AUTO LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
OPERATION
LCD REMOTE CONTROL
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF 45 45
RATED RUNNING CURRENT A
7.2 11.3
RATED INPUT POWER W 1585 2207
LOCKED ROTOR AMP. A 47 67
PROTECTION DEVICE
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A (50 Hz)
0.52 0.68
MOTOR OUTPUT
W (50 Hz)
65 75
RATED INPUT POWER W(50 Hz) 110 172
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
0.52 / 5.59 0.61 / 6.52
HEIGHT mm/in
648 / 25.5
750 / 29.5
DIMENSION WIDTH mm/in
855 / 33.7
855 / 33.7
DEPTH mm/in
328 / 12.9
328 / 12.9
WEIGHT kg/lb
59 / 130.07 62 / 136.69
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
51 53
TYPE
LIQUID mm/in 6.35 / 1/4 9.52 / 3/8
GAS mm/in
HEIGHT mm/in
710 / 28.0 810 / 31.9
WIDTH mm/in 990 / 39.0 990 / 39.0
DEPTH mm/in 415 / 16.3 415 / 16.3
REFRIGERANT CHARGE kg/lb 1.60 / 3.53 1.65 / 3.64
PACKING
DIMENSION
SIZE
15.88 / 5/8
GALVANISED MILD STEEL
0.8 / 0.031
POLYESTER POWDER
PIPE
FLARE VALVE
9.52 / 3/8
0.33 / 0.013
FIN
ALUMINIUM (SLIT FIN)
0.12/0.005
2
16
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
INT. O.L.P
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
460/18
1130 / 44.5
292 / 11.5
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY
20 / 0.79
SARANET FILTER + IONIZER + DEODORIZER
PACKING
DIMENSION
378 / 14.9
16 / 35.27
CONTROL
304 / 12.0
1062 / 41.8
222 / 8.7
THERMAL OVERLOAD
COIL
TUBEFIN
0.269 / 2.900
MODEL
NOMINAL COOLING CAPACITY
INDOOR UNIT
FAN
5
R22 Models
(Heatpump)
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
b) HEATING - 20°C DB / 15°C WB INDOOR AND 7°C DB / 6°C WB OUTDOOR
Abbreviation :
INT. O.L.P - Internal Overload Protector
EXT. O.L.P - External Overload Protector
INDOOR UNIT
MWM 009GR MWM 010GR MWM 015GR
OUTDOOR UNIT MLC 009CR MLC 010CR MLC 015CR
W
2640
2780 3520
Btu/h
9000
9500 12000
W 2640
2780 3520
Btu/h 9000
9500 12000
INPUT POWER (COOLING) W (50 Hz)
910 837 1100
INPUT POWER (HEATING) W (50 Hz) 750 757 980
RUNNING CURRENT (COOLING) A (50Hz) 4.0 3.8 5.0
RUNNING CURRENT (HEATING) A (50Hz)
3.4 3.4 4.5
POWER SOURCE V/Ph/Hz
REFRIGERANT / CONTROL
FAN TYPE
AIR FLOW cfm / L/s
275 / 130 300 / 142 345 / 163
FAN MOTOR 50 Hz 4 POLES X 8W 4 POLES X 9W 4 POLES X 13W
RATED INPUT POWER W (50 Hz) 24 26 29
RATED RUNNING CURRENT A (50 Hz)
0.11 0.11 0.13
FAN MOTOR PROTECTION
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/ft
2
0.201 / 2.161
HEIGHT mm/in 260 / 10.2
DIMENSION WIDTH mm/in
799 / 31.5
DEPTH mm/in
198 / 7.8
WEIGHT kg/lb
10/22.05
SOUND PRESSURE LEVEL- H / M / L dBA
40 / 35 / 29 39 / 34 / 28 42 / 36 / 29
ROOM TEMPERATURE
AIR DISCHARGE
OPERATION
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
337 / 13.3
WIDTH mm/in
857 / 33.7
DEPTH mm/in
270 / 10.6
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF
25 30 35
RATED RUNNING CURRENT (COOLING) A
3.7 3.4 4.7
A
3.1 3.0 4.1
RATED INPUT POWER (COOLING) W
846 759 1012
RATED INPUT POWER (HEATING) W 686 679 892
LOCKED ROTOR AMP. A 18 19 24
PROTECTION DEVICE
INT. O.L.P
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
356/14
RATED RUNNING CURRENT A (50 Hz)
0.18 0.23 0.26
MOTOR OUTPUT
W (50 Hz)
20 35 35
RATED INPUT POWER W(50 Hz) 40 52 59
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
0.31/3.40
HEIGHT mm/in 495/19.5
DIMENSION WIDTH mm/in 600/23.6
DEPTH mm/in 245/9.7
WEIGHT kg/lb
28/61.73
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
45 46 49
TYPE
LIQUID mm/in
GAS mm/in
12.7 / 1/2
HEIGHT mm/in 575/22.6
WIDTH mm/in 715/28.1
DEPTH mm/in 330/13.0
REFRIGERANT CHARGE kg/lb
0.75/1.65 0.88/1.94 0.8/1.76
PACKING
DIMENSION
620/24.4
810/31.9
330/13.0
0.5~2.0
EPOXY POLYESTER POWDER
PIPE
FLARE VALVE
SIZE
6.35 / 1/4
9.52 / 3/8
700/27.6
250/9.8
32/70.55
EG/GI
1
18
0.36/3.94
540/21.3
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
9.52 / 3/8
0.33 / 0.013
FIN
ALUMINIUM (SLIT FIN)
0.11/0.004
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY HERMETIC
RATED RUNNING CURRENT (HEATING)
EXT. O.L.P
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
404/16
16 / 0.63
SARANET+IONIZER+DEODORIZER
PACKING
DIMENSION
337 / 13.3
957 / 37.7
270 / 10.6
12/26.46
CONTROL
THERMOSTAT ELECTRONIC CONTROL
DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
LCD REMOTE CONTROL
0.234 / 2.516
260 / 10.2
899 / 35.4
198 / 7.8
ALUMINIUM (HYDROPHILIC SLIT FIN TYPE)
0.11 / 0.0043
2
18
SEAMLESS COPPER TUBE
INNER GROOVED
7.0 / 0.276
0.28 / 0.011
220-240/1/50
R22 / CAPILLARY TUBE IN OUTDOOR
FAN
ANTI FUNGUS SKEW FAN
THERMAL OVERLOAD RELAY
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
INDOOR UNIT
COIL
TUBEFIN
6
R22 Models
(Heatpump)
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
b) HEATING - 20°C DB / 15°C WB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) ALL SPECIFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
5) SOUND SPECTRUM FOR MWM 020/025G IS NOT READY AT THE TIME OF PRINTING.
Abbreviation :
INT. O.L.P - Internal Overload Protector
INDOOR UNIT
MWM 020GR MWM 025GR
OUTDOOR UNIT
MLC 020CR MLC 025CR
W 5569 7034
Btu/h 19000 24000
W 5569 7327
Btu/h
19000 25000
INPUT POWER (COOLING) W (50 Hz)
1715 2412
INPUT POWER (HEATING) W (50 Hz) 1802 2397
RUNNING CURRENT (COOLING) A (50Hz) 7.6 11.8
RUNNING CURRENT (HEATING) A (50Hz) 8.1 11.3
POWER SOURCE V/Ph/Hz
220-240/1/50
REFRIGERANT / CONTROL
R22 / OUTDOOR CAP. TUBE
FAN TYPE
CROSS FLOW FAN
AIR FLOW cfm / L/s 510 / 240.72 650/306.77
FAN MOTOR 50 Hz 4 POLES X 20W 4 POLES X 25W
RATED INPUT POWER W (50 Hz) 50 69
RATED RUNNING CURRENT A (50 Hz) 0.22 0.29
FAN MOTOR PROTECTION
MATERIAL COPPER
TUBE PATTERN
GROOVED
DIAMETER mm/in
7.0 / 0.276"
THICKNESS mm/in
0.28 / 0.011"
MATERIAL
ALUMINIUM
THICKNESS mm/in
0.11 / 0.0043"
ROW
2
FIN PER INCH
18
FACE AREA
m
2
/ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
SOUND PRESSURE LEVEL- H / M / L dBA 44 / 40 /35 49 / 43 / 40
ROOM TEMPERATURE
THERMOSTAT ELECTRONIC CONTROL
AIR DISCHARGE
AUTO LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
OPERATION
LCD REMOTE CONTROL
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF 45 45
RATED RUNNING CURRENT (COOLING) A 6.9 10.8
A
7.4 10.3
RATED INPUT POWER (COOLING) W 1555 2171
RATED INPUT POWER (HEATING) W
1642 2156
LOCKED ROTOR AMP. A 47 67
PROTECTION DEVICE
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A (50 Hz)
0.52 0.68
MOTOR OUTPUT
W (50 Hz)
65 75
RATED INPUT POWER W(50 Hz) 110 172
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
0.52 / 5.59 0.61 / 6.52
HEIGHT mm/in
648 / 25.5
750 / 29.5
DIMENSION WIDTH mm/in
855 / 33.7
855 / 33.7
DEPTH mm/in
328 / 12.9
328 / 12.9
WEIGHT kg/lb 59 / 130.07 62 / 136.69
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
51 53
TYPE
LIQUID mm/in 6.35 / 1/4 9.52 / 3/8
GAS mm/in
HEIGHT mm/in
710 / 28.0 810 / 31.9
WIDTH mm/in 990 / 39.0 990 / 39.0
DEPTH mm/in 415 / 16.3 415 / 16.3
REFRIGERANT CHARGE kg/lb 1.80 / 3.97 1.70 / 3.75
PACKING
DIMENSION
PIPE
FLARE VALVE
SIZE
15.88 / 5/8
0.8 / 0.031
POLYESTER POWDER
2
16
GALVANISED MILD STEEL
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
9.52 / 3/8
0.33 / 0.013
FIN
ALUMINIUM (SLIT FIN)
0.12/0.005
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY
RATED RUNNING CURRENT (HEATING)
INT. O.L.P
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
460/18
20 / 0.79
SARANET FILTER + IONIZER + DEODORIZER
PACKING
DIMENSION
378 / 14.9
1130 / 44.5
292 / 11.5
222 / 8.7
16 / 35.27
304 / 12.0
1062 / 41.8
THERMAL OVERLOAD
COIL
TUBEFIN
0.269 / 2.900
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
INDOOR UNIT
FAN
CONTROL
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
4) ALL SPECIFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
Abbreviation :
EXT. O.L.P - External Overload Protector
7
R407C Models
(Cooling only)
INDOOR UNIT
MWM 007G MWM 010G MWM 015G
OUTDOOR UNIT
M4LC 007B M4LC 010B M4LC 015B
W 2169 2638 3224
Btu/h
7400 9000 11000
INPUT POWER W (50 Hz)
855 977 1438
RUNNING CURRENT A (50Hz)
3.64 4.3 6.6
POWER SOURCE V/Ph/Hz
REFRIGERANT / CONTROL
FAN TYPE
AIR FLOW cfm / L/s
275 / 130 300 / 142 345 / 163
FAN MOTOR 50 Hz 4 POLES X 8W 4 POLES X 9W 4 POLES X 13W
RATED INPUT POWER W (50 Hz)
24 26 29
RATED RUNNING CURRENT A (50 Hz)
0.11 0.11 0.13
FAN MOTOR PROTECTION
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
0.201 / 2.161
HEIGHT mm/in
260 / 10.2
DIMENSION WIDTH mm/in 799 / 31.5
DEPTH mm/in
198 / 7.8
WEIGHT kg/lb
10/22.05
SOUND PRESSURE LEVEL- H / M / L dBA
40 / 35 / 29 39 / 34 / 28 42 / 36 / 29
ROOM TEMPERATURE
AIR DISCHARGE
OPERATION
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
337 / 13.3
WIDTH mm/in
857 / 33.7
DEPTH mm/in
270 / 10.6
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF 25 30 30
RATED RUNNING CURRENT A 3.32 4.0 6.2
RATED INPUT POWER W 781 900 1350
LOCKED ROTOR AMP. A
15 20 32
PROTECTION DEVICE
EXT. O.L.P EXT. O.L.P EXT. O.L.P
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A (50 Hz)
0.28
MOTOR OUTPUT
W (50 Hz)
25
RATED INPUT POWER W(50 Hz)
62
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
27.5/60.63 31/68.34 34/74.96
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
47 48 49
TYPE
LIQUID mm/in
GAS mm/in
12.70 / 1/2
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
REFRIGERANT CHARGE kg/lb
0.55/1.21 0.78/1.72 0.93/2.05
PACKING
DIMENSION
558/22.0
851/33.5
401/15.8
SIZE
6.35 / 1/4
9.52 / 3/8
0.8/0.031
EPOXY POLYESTER POWDER
PIPE
FLARE VALVE
494/19.4
740/29.1
270/10.6
GALVANIZE MILD STEEL
9.52 / 3/8
0.33 / 0.013
FIN
ALUMINIUM (SLIT FIN)
0.127/0.005
1
19
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
0.32/3.50
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
356/14
0.21
20
50
957 / 37.7
270 / 10.6
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY HERMETIC
16 / 0.63
SARANET+IONIZER+DEODORIZER
PACKING
DIMENSION
337 / 13.3
CONTROL
THERMOSTAT ELECTRONIC CONTROL
DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
LCD REMOTE CONTROL
198 / 7.8
12/26.46
0.234 / 2.516
260 / 10.2
899 / 35.4
FIN
ALUMINIUM (HYDROPHILIC SLIT FIN TYPE)
0.11 / 0.0043
2
18
SEAMLESS COPPER TUBE
INNER GROOVED
7.0 / 0.276
0.28 / 0.011
MODEL
NOMINAL COOLING CAPACITY
INDOOR UNIT
220-240/1/50
R407C / CAPILLARY TUBE IN OUTDOOR
FAN
ANTI FUNGUS SKEW FAN
THERMAL OVERLOAD RELAY
COIL
TUBE
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
4) ALL SPEC IFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
5) SOUND SPECTRUM FOR MWM 020/025G IS NOT READY AT THE TIME OF PRINTING.
Abbreviation :
INT. O.L.P - Internal Overload Protector
S.B.C. - Seamless Bare Copper
S.I.G.C. - Seamless Inner Groove Copper
8
R407C Models
(Cooling only)
INDOOR UNIT
MWM 020G MWM 025G
OUTDOOR UNIT
M4LC 020B M4LC 025B
W
5363 6155
Btu/h
18300 21000
INPUT POWER W
2295
2862
RUNNING CURRENT A
10.69
13.35
POWER SOURCE V/Ph/Hz
REFRIGERANT / CONTROL
FAN TYPE CROSS FLOW FAN
AIR FLOW cfm / L/s
510 / 240.72 650/306.77
FAN MOTOR 50 Hz
4 POLES X 20W 4 POLES X 25W
RATED INPUT POWER W
50 69
RATED RUNNING CURRENT A
0.22 0.29
FAN MOTOR PROTECTION
MATERIAL
COPPER
TUBE PATTERN
GROOVED
DIAMETER mm/in
7.0 / 0.276
THICKNESS mm/in
0.28 / 0.011
MATERIAL
ALUMINIUM
THICKNESS mm/in
0.11 / 0.0043
ROW
2
FIN PER INCH 18
FACE AREA
m
2
/
ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
SOUND PRESSURE LEVEL dBA
44 / 40 /35 49 / 43 / 40
ROOM TEMPERATURE THERMOSTAT ELECTRONIC CONTROL
CONTROL AIR DISCHARGE
AUTO LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
OPERATION LCD REMOTE CONTROL
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
PACKING HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF
45 50
RATED RUNNING CURRENT A 9.91 12.50
RATED INPUT POWER W 2,112 2,660
LOCKED ROTOR AMP. A 58 58
PROTECTION DEVICE
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A
MOTOR OUTPUT W
RATED INPUT POWER W
MATERIAL
S.B.C. S.I.G.C.
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
57 / 125.66 58 / 127.87
SOUND PRESSURE LEVEL dBA
52 53
MATERIAL
CASING THICKNESS mm/in
FINISHING
TYPE
SIZE LIQUID mm/in 6.35 / 1/4 9.52 / 3/8
GAS mm/in 15.88 / 5/8 15.88 / 5/8
PACKING HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
REFRIGERANT CHARGE kg/lb
1.65 / 3.64 1.65 / 3.64
710 / 28.0
957 / 37.7
461 / 18.1
0.8 / 0.031
EPOXY POLYESTER POWDER
PIPE
FLARE VALVE / AEROQUIP
646 / 25.4
840 / 33.1
330 / 13.0
GALVANIZED MILD STEEL
COIL
TUBE
9.52 / 3/8
0.33 / 0.013
FIN
ALUMINIUM (SLIT FIN TYPE)
0.127 / 0.005
2
14
0.51 / 5.53
406 / 16
0.56
55
133
1130 / 44.5
292 / 11.5
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY
INT. O.L.P
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRLY STYRENE RESIN
16 / 35.27
20 / 0.79
SARANET FILTER + IONIZER + DEODORIZER
378 / 14.9
0.269 / 2.900
304 / 12.0
1062 / 41.8
222 / 8.7
MODEL
NOMINAL COOLING CAPACITY
INDOOR UNIT
220-240/1/50
R22 / OUTDOOR CAP. TUBE
FAN
THERMAL OVERLOAD
COIL
TUBEFIN
9
R407C Models
(Heatpump)
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
b) HEATING - 20°C DB / 15°C WB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) ALL SPECIFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
Abbreviation :
EXT. O.L.P - External Overload Protector
INDOOR UNIT
MWM 007GR MWM 010GR MWM 015GR
OUTDOOR UNIT M4LC 007BR M4LC 010BR M4LC 015BR
W
2227 2638 3224
Btu/h
7600
9000 11000
W 2169 2784 3663
Btu/h 7400
9500 12500
INPUT POWER (COOLING) W (50 Hz)
794 977 1441
INPUT POWER (HEATING) W (50 Hz) 748 827 1291
RUNNING CURRENT (COOLING) A (50Hz)
3.41 4.3 6.6
RUNNING CURRENT (HEATING) A (50Hz)
3.21 3.6 6.1
POWER SOURCE V/Ph/Hz
REFRIGERANT / CONTROL
FAN TYPE
AIR FLOW cfm / L/s 275 / 130 300 / 142 345 / 163
FAN MOTOR 50 Hz 4 POLES X 8W 4 POLES X 9W 4 POLES X 13W
RATED INPUT POWER W (50 Hz)
24 26 29
RATED RUNNING CURRENT A (50 Hz)
0.11 0.11 0.13
FAN MOTOR PROTECTION
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/ft
2
0.201 / 2.161
HEIGHT mm/in
260 / 10.2
DIMENSION WIDTH mm/in
799 / 31.5
DEPTH mm/in 198 / 7.8
WEIGHT kg/lb 10/22.05
SOUND PRESSURE LEVEL- H / M / L dBA
40 / 35 / 29 39 / 34 / 28 42 / 36 / 29
ROOM TEMPERATURE
AIR DISCHARGE
OPERATION
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in 337 / 13.3
WIDTH mm/in
857 / 33.7
DEPTH mm/in
270 / 10.6
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF 25 30 30
RATED RUNNING CURRENT (COOLING) A
3.09 4.0 6.2
A
2.89 3.3 5.7
RATED INPUT POWER (COOLING) W
720 900 1350
RATED INPUT POWER (HEATING) W
674 750 1200
LOCKED ROTOR AMP. A
15 20 32
PROTECTION DEVICE EXT. O.L.P EXT. O.L.P EXT. O.L.P
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A (50 Hz)
0.28
MOTOR OUTPUT
W (50 Hz)
25
RATED INPUT POWER W(50 Hz)
62
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
ALUMINIUM (CORR. FIN)
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
27.5/60.63 31/68.34 34/74.96
MATERIAL
CASING THICKNESS mm/in
FINISHING
SOUND PRESSURE LEVEL
dBA
47 48 49
TYPE
LIQUID mm/in
GAS mm/in
12.70 / 1/2
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
REFRIGERANT CHARGE kg/lb
0.73/1.60 0.85/1.87 0.85/1.87
PACKING
DIMENSION
558/22.0
851/33.5
401/15.8
0.8/0.031
EPOXY POLYESTER POWDER
PIPE
FLARE VALVE
SIZE
6.35 / 1/4
9.52 / 3/8
494/19.4
740/29.1
270/10.6
GALVANIZE MILD STEEL
0.127/0.005
1
19
0.32/3.50
20
50
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
9.52 / 3/8
0.33 / 0.013
FIN
ALUMINIUM (SLIT FIN)
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY HERMETIC
RATED RUNNING CURRENT (HEATING)
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
356/14
0.21
16 / 0.63
SARANET+IONIZER+DEODORIZER
PACKING
DIMENSION
337 / 13.3
957 / 37.7
270 / 10.6
12/26.46
CONTROL
THERMOSTAT ELECTRONIC CONTROL
DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
LCD REMOTE CONTROL
0.234 / 2.516
260 / 10.2
899 / 35.4
198 / 7.8
ALUMINIUM (HYDROPHILIC SLIT FIN TYPE)
0.11 / 0.0043
2
18
SEAMLESS COPPER TUBE
INNER GROOVED
7.0 / 0.276
0.28 / 0.011
220-240/1/50
R407C / CAPILLARY TUBE IN OUTDOOR
FAN
ANTI FUNGUS SKEW FAN
THERMAL OVERLOAD RELAY
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
INDOOR UNIT
COIL
TUBEFIN
10
R407C Models
(Heatpump)
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
4) ALL SPECIFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
5) SOUND SPECTRUM FOR MWM 020/025G IS NOT READY AT THE TIME OF PRINTING.
Abbreviation :
INT. O.L.P - Internal Overload Protector
S.B.C. - Seamless Bare Copper
S.I.G.C. - Seamless Inner Groove Copper
INDOOR UNIT
MWM 020GR MWM 025GR
OUTDOOR UNIT
M4LC 020BR M4LC 025BR
W 5129 6008
Btu/h 17500 20500
W 5569 7034
Btu/h
19000 24000
INPUT POWER (COOLING) W (50 Hz)
2185 2773
INPUT POWER (HEATING) W (50 Hz) 2279 2751
RUNNING CURRENT (COOLING) A (50Hz) 10.3 13.5
RUNNING CURRENT (HEATING) A (50Hz) 10.9 13.4
POWER SOURCE V/Ph/Hz
220-240/1/50
REFRIGERANT / CONTROL
R22 / OUTDOOR CAP. TUBE
FAN TYPE
CROSS FLOW FAN
AIR FLOW cfm / L/s 510 / 240.72 650/306.77
FAN MOTOR 50 Hz 4 POLES X 20W 4 POLES X 25W
RATED INPUT POWER W (50 Hz) 50 69
RATED RUNNING CURRENT A (50 Hz) 0.22 0.29
FAN MOTOR PROTECTION
MATERIAL COPPER
TUBE PATTERN
GROOVED
DIAMETER mm/in
7.0 / 0.276"
THICKNESS mm/in
0.28 / 0.011"
MATERIAL
ALUMINIUM
THICKNESS mm/in
0.11 / 0.0043"
ROW
2
FIN PER INCH
18
FACE AREA
m
2
/ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
SOUND PRESSURE LEVEL- H / M / L dBA 44 / 40 /35 49 / 43 / 40
ROOM TEMPERATURE
THERMOSTAT ELECTRONIC CONTROL
AIR DISCHARGE
AUTO LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
OPERATION
LCD REMOTE CONTROL
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF 30 30
RATED RUNNING CURRENT (COOLING) A 9.50 12.60
A
10.10 12.50
RATED INPUT POWER (COOLING) W
2002 2571
RATED INPUT POWER (HEATING) W
2096 2549
LOCKED ROTOR AMP. A 58 58
PROTECTION DEVICE
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A (50 Hz)
MOTOR OUTPUT
W (50 Hz)
RATED INPUT POWER W(50 Hz)
TUBE PATTERN S.B.C. S.I.G.C.
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb 57 / 125.66 58 / 127.87
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
52 53
TYPE
LIQUID mm/in 6.35 / 1/4 9.52 / 3/8
GAS mm/in 15.88 / 5/8 15.88 / 5/8
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
REFRIGERANT CHARGE kg/lb 1.70 / 3.75 1.65 / 3.64
PIPE
FLARE VALVE / AEROQUIP
SIZE
PACKING
DIMENSION
710 / 28.0
957 / 37.7
461 / 18.1
0.8 / 0.031
EPOXY POLYESTER POWDER
646 / 25.4
840 / 33.1
330 / 13.0
GALVANIZED MILD STEEL
COIL
TUBE
9.52 / 3/8
0.33 / 0.013
FIN
ALUMINIUM (SLIT FIN TYPE)
0.127 / 0.005
2
14
0.51 / 5.53
0.56
55
133
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY
RATED RUNNING CURRENT (HEATING)
INT. O.L.P
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRLY STYRENE RESIN
406 / 16
20 / 0.79
SARANET FILTER + IONIZER + DEODORIZER
PACKING
DIMENSION
378 / 14.9
1130 / 44.5
292 / 11.5
222 / 8.7
16 / 35.27
304 / 12.0
1062 / 41.8
THERMAL OVERLOAD
COIL
TUBEFIN
0.269 / 2.900
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
INDOOR UNIT
FAN
CONTROL
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
Abbreviation :
EXT. O.L.P - External Overload Protector
11
R410A Models
(Cooling only)
INDOOR UNIT
M5WM 007G M5WM 009G M5WM 010G M5WM 015G
OUTDOOR UNIT M5LC 007C M5LC 010C M5LC 010C M5LC 015C
W 2200 2640 2780 3520
Btu/h 7500 9000 9500 12000
INPUT POWER W (50 Hz) 620 865 867 1230
RUNNING CURRENT A (50Hz)
2.93.9 3.95.5
POWER SOURCE V/Ph/Hz
REFRIGERANT / CONTROL
FAN TYPE
AIR FLOW cfm / L/s
300 / 142 345 / 163
FAN MOTOR 50 Hz
4 POLES X 9W 4 POLES X 13W
RATED INPUT POWER W (50 Hz)
26 29
RATED RUNNING CURRENT A (50 Hz) 0.11 0.13
FAN MOTOR PROTECTION
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
SOUND PRESSURE LEVEL- H / M / L dBA
39 / 34 / 28 42 / 36 / 29
ROOM TEMPERATURE
AIR DISCHARGE
OPERATION
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF
15 25 25 30
RATED RUNNING CURRENT A
2.6 3.6 3.6 5.1
RATED INPUT POWER W 556 789 789 1142
LOCKED ROTOR AMP. A 12 19 19 24
PROTECTION DEVICE EXT. O.L.P EXT. O.L.P EXT. O.L.P EXT. O.L.P
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
356/14
RATED RUNNING CURRENT A (50 Hz) 0.18 0.23 0.23 0.26
MOTOR OUTPUT
W (50 Hz)
20 35 35 35
RATED INPUT POWER W(50 Hz) 40 52 52 59
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
0.31/3.40
HEIGHT mm/in
495/19.5
DIMENSION WIDTH mm/in
600/23.6
DEPTH mm/in
245/9.7
WEIGHT kg/lb 26/57.32 33/72.75 33/72.75 35/77.16
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
44 46 46 49
TYPE
LIQUID mm/in
GAS mm/in 12.70 / 1/2
HEIGHT mm/in 575/22.6
WIDTH mm/in 715/28.1
DEPTH mm/in 330/13.0
REFRIGERANT CHARGE kg/lb
0.6/1.32 0.69/1.52 0.69/1.52 0.8/1.76
PACKING
DIMENSION
620/24.4
810/31.9
330/13.0
EG/GI
0.5~2.0
EPOXY POLYESTER POWDER
PIPE
FLARE VALVE
SIZE
6.35 / 1/4
9.52 / 3/8
0.36/3.94
540/21.3
700/27.6
250/9.8
FIN
ALUMINIUM (SLIT FIN)
0.11/0.004
1
18
SEAMLESS COPPER TUBE
INNER GROOVED
9.52 / 3/8
0.372 / 0.015
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY HERMETIC
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
404/16
COIL
TUBE
16 / 0.63
SARANET+IONIZER+DEODORIZER
PACKING
DIMENSION
337 / 13.3 337 / 13.3
857 / 33.7 957 / 37.7
270 / 10.6 270 / 10.6
40 / 35 / 29
CONTROL
THERMOSTAT ELECTRONIC CONTROL
DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
LCD REMOTE CONTROL
198 / 7.8
198 / 7.8
10 / 22.05 12/26.46
260 / 10.2
260 / 10.2
799 / 31.5
899 / 35.4
0.11 / 0.0043
2
18
0.201 / 2.161 0.234 / 2.516
0.11
THERMAL OVERLOAD RELAY
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
7.0 / 0.276
0.28 / 0.011
FIN
ALUMINIUM (HYDROPHILIC SLIT FIN TYPE)
MODEL
NOMINAL COOLING CAPACITY
INDOOR UNIT
220-240/1/50
R410A / CAPILLARY TUBE IN OUTDOOR
FAN
ANTI FUNGUS SKEW FAN
275 / 130
4 POLES X 8W
24
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
4) ALL SPECIFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
5) SOUND SPECTRUM FOR M5WM 020/025G IS NOT READY AT THE TIME OF PRINTING.
Abbreviation :
INT. O.L.P - Internal Overload Protector
12
R410A Models
(Cooling only)
INDOOR UNIT
M5WM 020G M5WM 025G
OUTDOOR UNIT
M5LC 020C M5LC 025C
W 5569 7034
Btu/h
19000 24000
INPUT POWER W (50 Hz)
1865 2602
RUNNING CURRENT A (50Hz)
8.3 12.4
POWER SOURCE V/Ph/Hz
220-240/1/50
REFRIGERANT / CONTROL R410A / OUTDOOR CAP.TUBE
FAN TYPE
CROSS FLOW FAN
AIR FLOW cfm / L/s
510 / 240.72 650/306.77
FAN MOTOR 50 Hz
4 POLES X 20W 4 POLES X 25W
RATED INPUT POWER W (50 Hz)
50 69
RATED RUNNING CURRENT A (50 Hz)
0.22 0.29
FAN MOTOR PROTECTION
MATERIAL COPPER
TUBE PATTERN GROOVED
DIAMETER mm/in
7.0 / 0.276
THICKNESS mm/in
0.28 / 0.011
MATERIAL
ALUMINIUM
THICKNESS mm/in 0.11 / 0.0043
ROW 2
FIN PER INCH
18
FACE AREA
m
2
ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
SOUND PRESSURE LEVEL- H / M / L dBA
44 / 40 /35 49 / 43 / 40
ROOM TEMPERATURE THERMOSTAT ELECTRONIC CONTROL
AIR DISCHARGE
AUTO LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
OPERATION LCD REMOTE CONTROL
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF
50 45
RATED RUNNING CURRENT A
7.6 11.4
RATED INPUT POWER W
1705 2361
LOCKED ROTOR AMP. A
35 67
PROTECTION DEVICE
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A (50 Hz) 0.52 0.68
MOTOR OUTPUT
W (50 Hz)
65 75
RATED INPUT POWER W(50 Hz)
110 172
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
ft
2
0.53 / 5.67 0.62 / 6.61
HEIGHT mm/in 648 / 25.5
750 / 29.5
DIMENSION WIDTH mm/in 855 / 33.7
855 / 33.7
DEPTH mm/in
328 / 12.9
328 / 12.9
WEIGHT kg/lb
54 / 119.05 61 / 134.48
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
51 53
TYPE
LIQUID mm/in
GAS mm/in 12.70 / 1/2 15.88 / 5/8
HEIGHT mm/in
710 / 28.0 810 / 31.9
WIDTH mm/in
990 / 39.0 990 / 39.0
DEPTH mm/in
415 / 16.3 415 / 16.3
REFRIGERANT CHARGE kg/lb 1.65 / 3.64 1.80 / 3.97
PACKING
DIMENSION
SIZE
6.35 / 1/4
GALVANISED MILD STEEL
0.8 / 0.031
POLYESTER POWDER
PIPE
FLARE VALVE
7.00 / 0.28
0.28 / 0.011
FIN
ALUMINIUM (CORRUGATED)
0.12/0.005
2
18
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
INT. O.L.P
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
460 / 18
1130 / 44.5
292 / 11.5
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY
20 / 0.79
SARANET FILTER + IONIZER + DEODORIZER
PACKING
DIMENSION
378 / 14.9
16 / 35.27
CONTROL
304 / 12.0
1062 / 41.8
222 / 8.7
THERMAL OVERLOAD
COIL
TUBEFIN
0.269 / 2.900
MODEL
NOMINAL COOLING CAPACITY
INDOOR UNIT
FAN
13
R410A Models
(Heatpump)
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
b) HEATING - 20°C DB / 15°C WB INDOOR AND 7°C DB / 6°C WB OUTDOOR
Abbreviation :
EXT. O.L.P - External Overload Protector
INDOOR UNIT M5WM 007GR M5WM 009GR M5WM 010GR M5WM 015GR
OUTDOOR UNIT M5LC 007CR M5LC 010CR M5LC 010CR M5LC 015CR
W
2200 2640
2780 3520
Btu/h
7500 9000
9500 12000
W
2200 2640
2780 3520
Btu/h
7500 9000
9500 12000
INPUT POWER (COOLING) W (50 Hz) 680 865 867 1200
INPUT POWER (HEATING) W (50 Hz) 550 745 747 1080
RUNNING CURRENT (COOLING) A (50Hz) 3.1 3.9 3.9 5.4
RUNNING CURRENT (HEATING) A (50Hz) 2.6 3.4 3.4 4.9
POWER SOURCE V/Ph/Hz
REFRIGERANT / CONTROL
FAN TYPE
AIR FLOW cfm / L/s
300 / 142 345 / 163
FAN MOTOR 50 Hz 4 POLES X 9W 4 POLES X 13W
RATED INPUT POWER W (50 Hz) 26 29
RATED RUNNING CURRENT A (50 Hz) 0.11 0.13
FAN MOTOR PROTECTION
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
SOUND PRESSURE LEVEL- H / M / L dBA
39 / 34 / 28 42 / 36 / 29
ROOM TEMPERATURE
AIR DISCHARGE
OPERATION
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF 15 25 25 30
RATED RUNNING CURRENT (COOLING) A 2.8 3.6 3.6 5.0
A
2.4 3.0 3.0 4.5
RATED INPUT POWER (COOLING) W 616 789 789 1112
RATED INPUT POWER (HEATING) W 486 669 669 992
LOCKED ROTOR AMP. A 12 19 19 24
PROTECTION DEVICE
EXT. O.L.P EXT. O.L.P EXT. O.L.P EXT. O.L.P
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in 356/14
RATED RUNNING CURRENT A (50 Hz) 0.18 0.23 0.23 0.26
MOTOR OUTPUT
W (50 Hz)
20 35 35 35
RATED INPUT POWER W(50 Hz)
41 52 52 59
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/ft
2
0.31/3.40
HEIGHT mm/in
495/19.5
DIMENSION WIDTH mm/in
600/23.6
DEPTH mm/in
245/9.7
WEIGHT kg/lb
26/57.32 33/72.75 33/72.75 35/77.16
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
44 46 46 49
TYPE
LIQUID mm/in
GAS mm/in 12.70 / 1/2
HEIGHT mm/in 575/22.6
WIDTH mm/in 715/28.1
DEPTH mm/in
330/13.0
REFRIGERANT CHARGE kg/lb 0.8/1.76 0.73/1.61 0.73/1.61 0.78/1.72
PACKING
DIMENSION
620/24.4
810/31.9
330/13.0
PIPE
FLARE VALVE
SIZE
6.35 / 1/4
9.52 / 3/8
0.5~2.0
EPOXY POLYESTER POWDER
540/21.3
700/27.6
250/9.8
EG/GI
0.11/0.004
1
18
0.36/3.94
404/16
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
9.52 / 3/8
0.372 / 0.015
FIN
ALUMINIUM (SLIT FIN)
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY HERMETIC
RATED RUNNING CURRENT (HEATING)
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
SARANET+IONIZER+DEODORIZER
PACKING
DIMENSION
337 / 13.3 337 / 13.3
857 / 33.7 957 / 37.7
270 / 10.6 270 / 10.6
THERMOSTAT ELECTRONIC CONTROL
DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
LCD REMOTE CONTROL
16 / 0.63
10 / 22.05 12 / 26.46
40 / 35 / 29
799 / 31.5
899 / 35.4
198 / 7.8
198 / 7.8
0.201 / 2.161 0.234 / 2.516
260 / 10.2
260 / 10.2
ALUMINIUM (HYDROPHILIC SLIT FIN TYPE)
0.11 / 0.0043
2
18
SEAMLESS COPPER TUBE
INNER GROOVED
7.0 / 0.276
0.28 / 0.011
220-240/1/50
R410A / CAPILLARY TUBE IN OUTDOOR
FAN
ANTI FUNGUS SKEW FAN
275 / 130
4 POLES X 8W
24
0.11
THERMAL OVERLOAD RELAY
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
INDOOR UNIT
COIL
TUBEFIN
CONTROL
14
R410A Models
(Heatpump)
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151: 1994(E)
3) NOMINAL COOLING CAPACITY IS BASED ON THE CONDITIONS BELOW :
a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB OUTDOOR
b) HEATING - 20°C DB / 15°C WB INDOOR AND 7°C DB / 6°C WB OUTDOOR
4) ALL SPECIFICATIONS ARE TENTATIVE SPECIFICATIONS AT THE TIME OF PRINTING. PLEASE CONSULT YOUR DEALER FOR CONFIRMATION.
5) SOUND SPECTRUM FOR M5WM 020/025GR IS NOT READY AT THE TIME OF PRINTING.
Abbreviation :
INT. O.L.P -Inxternal Overload Protector
INDOOR UNIT
M5WM 020GR M5WM 025GR
OUTDOOR UNIT
M5LC 020CR M5LC 025CR
W
5569 6741
Btu/h
19000 23000
W
5569 6741
Btu/h
19000 23000
INPUT POWER (COOLING) W (50 Hz)
1921 2615
INPUT POWER (HEATING) W (50 Hz) 1882 2413
RUNNING CURRENT (COOLING) A (50Hz) 8.5 12.8
RUNNING CURRENT (HEATING) A (50Hz) 8.1 11.6
POWER SOURCE V/Ph/Hz
220-240/1/50
REFRIGERANT / CONTROL R410A / OUTDOOR CAP.TUBE
FAN TYPE
CROSS FLOW FAN
AIR FLOW cfm / L/s
510 / 240.72 650/306.77
FAN MOTOR 50 Hz
4 POLES X 20W 4 POLES X 25W
RATED INPUT POWER W (50 Hz)
50 69
RATED RUNNING CURRENT A (50 Hz) 0.22 0.29
FAN MOTOR PROTECTION
MATERIAL
COPPER
TUBE PATTERN
GROOVED
DIAMETER mm/in
7.0 / 0.276"
THICKNESS mm/in
0.28 / 0.011"
MATERIAL
ALUMINIUM
THICKNESS mm/in
0.11 / 0.0043"
ROW
2
FIN PER INCH
18
FACE AREA
m
2
/ft
2
HEIGHT mm/in
DIMENSION WIDTH mm/in
DEPTH mm/in
WEIGHT kg/lb
SOUND PRESSURE LEVEL- H / M / L dBA 44 / 40 /35 49 / 43 / 40
ROOM TEMPERATURE
THERMOSTAT ELECTRONIC CONTROL
AIR DISCHARGE
AUTO LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)
OPERATION
LCD REMOTE CONTROL
CONDENSATE DRAIN SIZE mm/in
AIR FILTER
HEIGHT mm/in
WIDTH mm/in
DEPTH mm/in
POWER SOURCE V/Ph/Hz
COMPRESSOR TYPE
CAPACITOR µF 50 45
RATED RUNNING CURRENT (COOLING) A 7.8 11.8
A
7.4 10.6
RATED INPUT POWER (COOLING) W 1761 2374
RATED INPUT POWER (HEATING) W 1722 2172
LOCKED ROTOR AMP. A 35 67
PROTECTION DEVICE
FAN TYPE / DRIVE
BLADE MATERIAL
DIAMETER mm/in
RATED RUNNING CURRENT A (50 Hz) 0.52 0.68
MOTOR OUTPUT
W (50 Hz)
65 75
RATED INPUT POWER W(50 Hz) 110 172
MATERIAL
TUBE PATTERN
DIAMETER mm/in
THICKNESS mm/in
MATERIAL
THICKNESS mm/in
ROW
FIN PER INCH
FACE AREA
m
2
/
ft
2
0.53 / 5.67 0.62 / 6.61
HEIGHT mm/in
648 / 25.5
750 / 29.5
DIMENSION WIDTH mm/in
855 / 33.7
855 / 33.7
DEPTH mm/in
328 / 12.9
328 / 12.9
WEIGHT kg/lb
54 / 119.05 61 / 134.48
MATERIAL
CASING THICKNESS mm
FINISHING
SOUND PRESSURE LEVEL
dBA
51 53
TYPE
LIQUID mm/in
GAS mm/in 12.70 / 1/2 15.88 / 5/8
HEIGHT mm/in 710 / 28.0 810 / 31.9
WIDTH mm/in 990 / 39.0 990 / 39.0
DEPTH mm/in
415 / 16.3 415 / 16.3
REFRIGERANT CHARGE kg/lb
1.60 / 3.53 1.70 / 3.75
PACKING
DIMENSION
PIPE
FLARE VALVE
SIZE
6.35 / 1/4
0.8 / 0.031
POLYESTER POWDER
2
18
GALVANISED MILD STEEL
COIL
TUBE
SEAMLESS COPPER TUBE
INNER GROOVED
7.00 / 0.28
0.28 / 0.011
FIN
ALUMINIUM (CORRUGATED)
0.12/0.005
OUTDOOR UNIT
220-240/1/50
COMPRESSOR
ROTARY
RATED RUNNING CURRENT (HEATING)
INT. O.L.P
FAN
PROPELLER / DIRECT
GLASS REINFORCED ACRYL STYRENE RESIN
460 / 18
20 / 0.79
SARANET FILTER + IONIZER + DEODORIZER
PACKING
DIMENSION
378 / 14.9
1130 / 44.5
292 / 11.5
222 / 8.7
16 / 35.27
304 / 12.0
1062 / 41.8
THERMAL OVERLOAD
COIL
TUBEFIN
0.269 / 2.900
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
INDOOR UNIT
FAN
CONTROL
Performance Table
15
Interpolation and Extrapolation method can be used to get the total capacity, TC and sensible capacity, SC
at those temperatures which are not stated out in the table.
Example:
Model: MWM 010G / MLC 010C
Indoor Condition: 23°C DB, 15°C WB
Outdoor Condition: 37°C DB
Solution:
Overall
Based on the Performance table on Pg. 19,
1. Refer to the Indoor DB column,
- 23°C is located between 20°C and 24°C (Thus, Interpolation need to be applied)
2. Refer to the Indoor WB column,
- 15°C only available in the case of Indoor DB = 20°C. (Thus, Extrapolation between 16°C WB
and 17°C WB during 24°C indoor DB is required)
3. Refer to the Outdoor DB column,
- 37°C is located between 35°C and 40°C. (Thus, Interpolation need to be applied)
Please follow the steps below in order to get the required capacity.
3
rd
Step
Interpolation of Outdoor DB
Find TC, SC for
(a) Indoor: 23°C DB, 15°C WB
Outdoor: 37°C DB
2
nd
Step
Interpolation of Indoor DB
Find TC, SC for
(a) Indoor: 23°C DB, 15°C WB
Outdoor: 35°C DB
(b) Indoor: 23°C DB, 15°C WB
Outdoor: 40°C DB
1
st
Step
Extrapolation of Indoor WB
Find TC, SC for
(a) Indoor: 24°C DB, 15°C WB
Outdoor: 35°C DB
(b) Indoor: 24°C DB, 15°C WB
Outdoor: 40°C DB
16
Details:
1
st
Step:
To obtain the Total capacity and Sensible capacity for
(a) Indoor Condition: 24°C DB, 15°C WB
Outdoor Condition: 35°C DB
Total capacity, TC
⇒
1
x = 2.560kW (Same as Total capacity at 20°C Indoor DB / 15°C Indoor WB & 35°C Outdoor WB)*
Sensible capacity, SC
Extrapolation Method:
⇒
⇒ y
1
= 1.985kW
(b) Indoor Condition: 24°C DB, 15°C WB
Outdoor Condition: 40°C DB
Total capacity, TC
⇒
2
x = 2.356kW (Same as Total capacity at 20°C Indoor DB / 15°C Indoor WB & 40°C Outdoor WB)*
Sensible capacity, SC
Extrapolation Method:
⇒
⇒ y
2
= 1.797kW
* This is due to 2 different conditions with same WB temperature, will have the same level of enthalpy. For
more details, please refer to psychrometrics chart
17°C - 15°C
=
1.790kW - y
1
17°C - 16°C 1.790kW - 1.888kW
17°C - 15°C
=
1.649kW - y
2
17°C - 16°C 1.649kW - 1.723kW
Indoor DB
Indoor WB
° C
° C
TC (kW)
SC (kW)
15
x
1
y
1
16
2.624 1.888
17
2.688 1.790
Outdoor DB ° C
35
24
Indoor DB
Indoor WB
° C
° C
TC (kW)
SC (kW)
15
x
2
y
2
16
2.429 1.723
17
2.503 1.649
40
24
Outdoor DB ° C
17
2
nd
Step:
To obtain the Total capacity and Sensible capacity for
(a) Indoor Condition: 23°C DB, 15°C WB
Outdoor Condition: 35°C DB
Total capacity, TC
⇒
3
x = 2.560kW (Same as Total capacity at 20°C Indoor DB / 15°C Indoor WB & 35°C Outdoor WB)*
Sensible capacity, SC
Interpolation Method:
⇒
⇒ y
3
= 1.839kW
(b) Indoor Condition: 23°C DB, 15°C WB
Outdoor Condition: 40°C DB
Total capacity, TC
⇒
4
x = 2.356kW (Same as Total capacity at 20°C Indoor DB / 15°C Indoor WB & 40°C Outdoor WB)*
Sensible capacity, SC
Interpolation Method:
⇒
⇒ y
4
= 1.651kW
* This is due to 2 different conditions with same WB temperature will have the same level of enthalpy. For
more details, please refer to psychrometrics chart
24°C - 20°C
=
1.985kW - 1.398kW
24°C - 23°C 1.985kW - y
3
24°C - 20°C
=
1.797kW - 1.211kW
24°C - 23°C 1.797kW - y
4
Indoor DB
Indoor WB
° C
° C
TC (kW)
SC (kW)
20
15
2.560 1.398
23 15
x
3
y
3
24
15
2.560 1.985
Outdoor DB ° C
35
Indoor DB
Indoor WB
° C
° C
TC (kW)
SC (kW)
20
15
2.356 1.211
23 15
x
4
y
4
24
15
2.356 1.797
Outdoor DB ° C
40
18
3
rd
Step:
To obtain the Total capacity and Sensible capacity for
(a) Indoor Condition: 23°C DB, 15°C WB
Outdoor Condition: 37°C DB
Total capacity, TC
Interpolation Method:
⇒
⇒ x = 2.478kW
Sensible capacity, SC
Interpolation Method:
⇒
⇒ y = 1.763kW
40°C - 35°C
=
2.356kW - 2.560kW
40°C - 37°C 2.356kW - x
40°C - 35°C
=
1.651kW - 1.839kW
40°C - 37°C 1.651kW - y
Indoor DB
Indoor WB
° C
° C
TC (kW)
SC (kW)
TC (kW)
SC (kW)
TC (kW)
SC (kW)
24 15
2.560 1.839
x y
2.356 1.651
40
Outdoor DB ° C
35
37
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118

McQuay M5WM 007G User manual

McQuay
Brand
McQuay
Model
M5WM 007G
Category
Split-system air conditioners
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents