McQuay M5WM015JR User manual

Wall Mounted Split Systems

Models:

MWM009J/JR

MWM015J/JR

M5WM010J/JR

M5WM015J/JR

Catalog

MWM - J - 2009

Cover.indd 1Cover.indd 1 3/6/2009 6:06:22 PM3/6/2009 6:06:22 PM

Catalog.indb 2Catalog.indb 2 3/2/2009 4:40:55 PM3/2/2009 4:40:55 PM

MWM-J-2009 Table of Contents

Bulletin illustrations cover the general appearance of McQuay International products at the time of publication.

We reserve the right to change design and construction speciﬁ cations at any time without notice.

Table of Contents

Nomenclature......................................................................................................................1

Indoor Unit .....................................................................................................................1

Outdoor Unit ..................................................................................................................2

Product Line-Up .............................................................................................................3

Features...............................................................................................................................7

Application Information .....................................................................................................8

Operating Range ...........................................................................................................8

Refrigerant Circuit Diagram ...........................................................................................9

Controller ....................................................................................................................11

Installation Guideline ...................................................................................................12

Sound Data ........................................................................................................................24

Sound Pressure Level .................................................................................................24

NC Curve .....................................................................................................................25

Engineering & Physical Data ........................................................................................... 27

General Data ...............................................................................................................27

Component Data .........................................................................................................31

Performance Data ............................................................................................................. 35

Calculation Steps .........................................................................................................36

Performance Table ......................................................................................................39

Outline and Dimension ....................................................................................................45

Electrical Data ................................................................................................................... 46

Wiring Diagram .................................................................................................................48

Service and Maintenance.................................................................................................50

Troubleshooting ...............................................................................................................52

Exploded View and Part List ...........................................................................................60

Catalog.indb 3Catalog.indb 3 3/2/2009 4:40:55 PM3/2/2009 4:40:55 PM

Nomenclature MWM-J-2009

1

Nomenclature

Indoor Unit

M 5 WM 010 J R

Brand

M : Mcquay

Refrigerant

“ “

4

5

: Omitted if R22

: R407C

: R410A

Model Name

WM : Wall Mounted

Capacity Index

010

015

: 10,000 Btu/h

: 15,000 Btu/h

Series

G

J

: G Series

: J Series

Model Type

“ “

R

: Omitted if cooling only

: Heatpump

Catalog.indb 1Catalog.indb 1 3/2/2009 4:40:55 PM3/2/2009 4:40:55 PM

MWM-J-2009 Nomenclature

2

Outdoor Unit

M 5 LC 010 C R

Brand

M : Mcquay

Refrigerant

“ “

4

5

: Omitted if R22

: R407C

: R410A

Model Name

LC : Single Split Condensing Unit

Capacity Index

010

015

: 10,000 Btu/h

: 15,000 Btu/h

Series

C : C Series

Model Type

“ “

R

: Omitted if cooling only

: Heatpump

Catalog.indb 2Catalog.indb 2 3/2/2009 4:40:55 PM3/2/2009 4:40:55 PM

3

Product Line-Up MWM-J-2009

Product Line-Up

Indoor Unit

MWM-J

MWM

Nomenclature

Classiﬁ cation

PCB

Handset

Air Puriﬁ cation

Grille

Marking

Others

LGSN

G17

Saranet Filter

Bio Filter

A

CE

COOLING

ONLY

009J

ACBAA X X X X X X

009J

ACLAA X X X X X

015J

ACBAA X X X X X X

015J

ACLAA X X X X X

HEATPUMP

009JR

ACBAA X X X X X X

009JR

ACLAA X X X X X

015JR

ACBAA X X X X X X

015JR

ACLAA X X X X X

Catalog.indb 3Catalog.indb 3 3/2/2009 4:40:55 PM3/2/2009 4:40:55 PM

4

MWM-J-2009 Product Line-Up

Indoor Unit

M5WM-J

M5WM

Nomenclature

Classiﬁ cation

PCB

Handset

Air Puriﬁ cation

Grille

Marking

Others

LGSN

G17

Saranet Filter

Bio Filter

A

CE

COOLING

ONLY

010J ACBAA X X X X X X

010J ACLAA X X X X X

015J ACBAA X X X X X X

015J ACLAA X X X X X

HEATPUMP

010JR ACBAA X X X X X X

010JR ACLAA X X X X X

015JR ACBAA X X X X X X

015JR ACLAA X X X X X

Catalog.indb 4Catalog.indb 4 3/2/2009 4:40:56 PM3/2/2009 4:40:56 PM

5

Product Line-Up MWM-J-2009

Outdoor Unit

MLC

Nomenclature

Classiﬁ cation

PCB

Refrigerant

Control

FIN

Safety Devices

Compressor

Marking

Others

Cap Tube

EXV

Gold Coated

Blue Coated

Bare

Contactor

HP

LP

Rotary

CE

Drain Elbow

Low Ambient Kit

COOLING

ONLY

009C ACPOH X X X X

015C ACPOH X X X X

HEATPUMP

009CR ACPOH X X X X X

015CR ACPOJ X X X X X

Catalog.indb 5Catalog.indb 5 3/2/2009 4:40:56 PM3/2/2009 4:40:56 PM

6

MWM-J-2009 Product Line-Up

Outdoor Unit

M5LC

Nomenclature

Classiﬁ cation

PCB

Refrigerant

Control

FIN

Safety Devices

Compressor

Marking

Others

Cap Tube

EXV

Gold Coated

Blue Coated

Bare

Contactor

HP

LP

Rotary

CE

Drain Elbow

Low Ambient Kit

COOLING

ONLY

010C ACPGG X X X X X

010C ACPOG X X X X

015C ACPGG X X X X X

015C ACPOG X X X X

HEATPUMP

010CR ACPOG X X X X

015CR ACPOG X X X X

Catalog.indb 6Catalog.indb 6 3/2/2009 4:40:56 PM3/2/2009 4:40:56 PM

7

Features MWM-J-2009

Features

Air Filtration with Bio Antibody Filter and Photo-catalytic Deodorizing Titanium Apatite

Filter

Bio Antibody Filter is effective against various airborne infectious viruses while Titanium Apatite Filter is able to

trap microscopic particles as well as break down and decompose odors. The ﬁ lter can be used for approximately

3 years without replacement if wash about once every six months.

Self Diagnosis

The microprocessor provides the possibility to detect and diagnose any fault or malfunction that occurs in the

system. The error will be reﬂ ected by the blinking of the LED lights.

On / Off Button on Indoor Unit

On/Off button is provided on the front panel of the unit. It can be used when the remote controller is missing or

if its battery has run out. (Note: This button can also be used for forced operation mode)

Auto Random Restart

Auto random restart function allows the unit to automatic restart as the last setting condition when the power

supply is resumed after power failure. However, the compressor will restart randomly if more than one unit is

installed and sharing the same phase of power.

Wireless Remote Controller

The compact LCD transmitter is able to operate the air conditioner unit within the distance of 8 meters.

Fan speed can be set at high / medium / low / super low or automatic.

Sleep mode auto control will gradually increase or decrease the setting temperature to provide a

comfortable surrounding for sleeping.

Air ﬂ ow direction can be controlled automatically.

Room temperature is controlled by electronic thermostat.

The real time timer allows the air conditioner to be switched On and Off automatically based on user

settings.

Turbo mode function is available to enables the required set temperature to be achieved in a short time.

Personalized Setting allows user to preset and store 2 groups of personal settings (including timer setting)

in the handset.

Energy Efﬁ ciency

Using a more efﬁ cient compressor and superior R410A refrigerant, M5WM10JR series achieves the highest

European Energy Rating of A/A. This ensures higher energy savings is accomplished especially during daily

usage. M5WM-J series participates in the Eurovent Certiﬁ cation Programme under category of Comfort Air

Conditioners rated below 12kW cooling capacity (AC1). The certiﬁ ed data for the certiﬁ ed models are listed in

the Eurovent Directory.

•

Catalog.indb 7Catalog.indb 7 3/2/2009 4:40:57 PM3/2/2009 4:40:57 PM

8

MWM-J-2009 Application Information

Application Information

Operating Range

Ensure the operating temperature is in allowable range.

Cooling only

Note :

Standard operating range.

With Low ambient kit. (Optional item)

Please refer to local dealer for unit of this specification.

Indoor temp. (°CDB)

Cooling

Outdoor temp. (°CDB)

Indoor temp. (°CWB)

Outdoor temp. (°CDB)

Indoor temp. (°CWB)

Heating

Outdoor temp. (°CWB)

-9

16 21

6

30

-5

19

35

14

46

23

Standard

point

Low ambient kit

18

-5

19

35

14

46

23

Low ambient kit

Standard

point

Standard

point

! Caution :

The use of your air conditioner

outside the range of working

temperature and humidity can

result in serious failure.

Heatpump

Catalog.indb 8Catalog.indb 8 3/2/2009 4:40:57 PM3/2/2009 4:40:57 PM

9

Application Information MWM-J-2009

70034 049971

Refrigerant Circuit Diagram

Model: MWM009J - MLC009C M5WM010J - M5LC010C

MWM015J - MLC015C M5WM015J - M5LC015C

70034 023154

Model: MWM009JR - MLC009CR M5WM010JR - M5LC010CR

M5WM015JR - M5LC015CR

Catalog.indb 9Catalog.indb 9 3/2/2009 4:40:58 PM3/2/2009 4:40:58 PM

10

MWM-J-2009 Application Information

70034 095236

Model: MWM015JR - MLC015CR

Catalog.indb 10Catalog.indb 10 3/2/2009 4:40:58 PM3/2/2009 4:40:58 PM

11

Application Information MWM-J-2009

Controller

G17

Operation Guide

1 Transmission Source

The source where the signal will be transmitted.•

2 Signal Transmission Indication

Blink to conﬁ rm that the last setting has been transmitted

to the unit.

•

3 Temperature Setting

To set the desired room temperature, press the v or V

button to increase orde crease the set temperature.

The temperature setting range is from 16°C to 30°C

(optional setting 20°C to 30°C).

•

4 Personalize Setting

Press

and hold for 3s, then will blink. Press again to

cycle between and

Set the desire setting, then leave the hand set for 4s

without pressing any key and it will save the setting into the

programme.

Press once to activate the P1 setting, press again to

cycle between P1 and P2.

Press any key to deactivate the personalize setting.

•

5 Automatic Air Swing (optional)

Press the SWING

button to activate the automatic air

swing function.

To distribute the air to a speciﬁ c direction, press the

SWING button and wait until the louver move to the

desired direction and press the button once again.

•

6 Silent Function

Press

for quiet operation.

Fan speed turn to minimum speed.

Press again to deactivate the function.

•

7 Sleep Mode Setting

Press the SLEEP button will activate the sleep mode

function. This function is available under COOL, HEAT and

AUTO mode.

When the unit is operating under cooling mode, the set

temperature is increased by 0.5°C after 30 minutes, 1°C

after an hour, and 2°C after 2 hours.

When the unit is operating under heating mode, the set

temperature is decreased by 1°C after 30 minutes, 2°C

after an hour, and 3°C after 2 hours.

•

8 Operating Mode

Press the MODE button to select the type of operating

mode.

For cooling only unit, the available modes are: COOL (

7

),

DRY (6) and FAN (

).

•

9 Fan Speed Selection

Press the

button continuously will toggle the fan speed

in the following order:

Low p Med p High p Auto

Stop pressing when the desired fan speed appears on the

display screen.

•

10 “ON/OFF” Button

Press one to start the air conditioner unit.

Press again to stop the unit.

•

11 Timer Cancel

Press the TIMER CANCEL button to cancel the on timer

setting.

•

12 OFF Timer Setting

Press the OFF TIMER button will activate the off timer

function.

Set the desired off time by pressing the OFF TIMER button

continuously.

•

13 ON Timer Setting

Press the ON TIMER button will activate the on timer

function.

Set the desired on time by pressing the ON TIMER

button continuously. If the timer is set to 7.30am, the air

conditioner will turn on at 7.30am sharp.

•

14 Turbo Function

Press

for fast cooling.

Fan speed turn to maximum speed.

Press again to deactivate the function.

•

15 Clock Time Setting

Press

and hold to set the clock time.•

MODE

P1 P2

SLEEP

SET

CANCEL

ON TIMER

SET

CANCEL

OFF TIMER

6a 6b

12

15

11

13

14

7

4

3

10

9

2

1

8

5

05_Application Information.indd 1105_Application Information.indd 11 4/1/2009 8:28:08 AM4/1/2009 8:28:08 AM

12

MWM-J-2009 Application Information

Installation Guideline

Safety Precautions

WARNING

CAUTION

Installation and maintenance should be performed by

qualiﬁ ed persons who are familiar with local code and

regulation, and experienced with this type of appliance.

All ﬁ eld wiring must be installed in accordance with the

national wiring regulation.

Ensure that the rated voltage of the unit corresponds

to that of the name plate before commencing wiring

work according to the wiring diagram.

The unit must be GROUNDED to prevent possible

hazard due to insulation failure.

All electrical wiring must not touch the refrigerant

piping or any moving parts of the fan motors.

Conﬁ rm that the unit has been switched OFF before

installing or servicing the unit.

Disconnect from the main power supply before

servicing the air conditioner unit.

DO NOT pull out the power cord when the power is

ON. This may cause serious electrical shocks which

may result in ﬁ re hazards.

Keep the indoor and outdoor units, power cable and

transmission wiring, at least 1m from TVs and radios,

to prevent distorted pictures and static. {Depending on

the type and source of the electrical waves, static may

be heard even when more than 1m away}.

•

Please take note of the following important points

when installing.

Do not install the unit where leakage of ﬂ ammable

gas may occur.

If gas leaks and accumulates around the unit, it

may cause ﬁ re ignition.

Ensure that drainage piping is connected properly.

If the drainage piping is not connected properly,

it may cause water leakage which will dampen

the furniture.

Do not overcharge the unit.

This unit is factory pre-charged. Overcharge will

cause over-current or damage to the compressor.

Ensure that the unit’s panel is closed after service

or installation.

Unsecured panels will cause the unit to operate

noisily.

Sharp edges and coil surfaces are potential

locations which may cause injury hazards. Avoid

from being in contact with these places.

Before turning off the power supply, set the remote

controller’s ON/OFF switch to the “OFF” position

to prevent the nuisance tripping of the unit. If this is

not done, the unit’s fans will start turning automatically

when power resumes, posing a hazard to service

personnel or the user.

Do not operate any heating apparatus too close to the

air conditioner unit. This may cause the plastic panel to

melt or deform as a result of the excessive heat.

Ensure the color of wires of the outdoor unit and

the terminal markings are same to the indoors

respectively.

IMPORTANT : DO NOT INSTALL OR USE THE

AIR CONDITIONER UNIT IN A LAUNDRY ROOM.

Do not use joined and twisted wires for incoming

power supply.

•

NOTICE

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products

shall not be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of

the refrigerant, of oil and of other parts must be done by a qualiﬁ ed installer in accordance with relevant

local and national legislation. Air conditioners must be treated at a specialized treatment facility for re-use,

recycling and recovery. By ensuring this product is disposed of correctly, you will help to prevent potential

negative consequences for the environment and human health. Please contact the installer or local authority

for more information.

Batteries must be removed from the remote controller and disposed of separately in accordance with relevant

local and national legislation.

Catalog.indb 12Catalog.indb 12 3/2/2009 4:41:00 PM3/2/2009 4:41:00 PM

13

Application Information MWM-J-2009

Installation Diagram

Indoor Unit

Air filter

M4 x 12L

Air-Purifying Filter with

bacteriostatic virustatic function (2)

Front panel

30mm or more from ceiling

Outdoor Unit

50mm or more from walls

(on both sides)

Air filter

Air-Purifying Filter with

bacteriostatic virustatic

function

Filter frame

Tab

Caulk pipe

hole gap

with putty.

Cut thermal insulation

pipe to an appropriate

length and wrap it with

tape, making sure that no

gap is left in the insulation

pipe's cut line.

Wrap the insulation pipe with

the finishing tape from bottom

to top.

Service lid

Opening service lid

Service lid is opening/closing

type.

Opening method

1) Remove the service lid

screws.

2) Pull out the service lid

diagonally down in

thedirection of the arrow.

1) Pull down.

250mm from wall

Caution

Before installing the unit, ensure that the power supply matches the power requirement of the air conditioner.•

Installation of Indoor Unit

Service Space

Install the indoor unit at a location with the following requirements

Location is suitable for wiring, piping and drainage.

No obstruction of air ﬂ ow into and out of unit where cooler air can be evenly distributed.

Ensure that air discharge is not short circuited with air intake.

Ensure that wall is sufﬁ ciently strong, rigid, ﬂ at, perpendicular and vibration free.

Where air ﬁ lter cassette can be slided in or out easily.

Where there is no danger of ﬂ ammable gases.

Where there is no direct sunlight on unit.

min. 50

(Space for

maintenance)

Air flow

(Indoor)

min. 50

(Space for

maintenance)

03.n

im

rofecap

S(

)ecn

am

rof

rep

Required space

•

Catalog.indb 13Catalog.indb 13 3/2/2009 4:41:01 PM3/2/2009 4:41:01 PM

14

MWM-J-2009 Application Information

Routing of Piping

The refrigerant piping can be routed to the unit in one of 5 directions, by using the cut outs in the unit

casing (refer to Figure 1).

1

2

3

4

5

Figure 1

Carefully bend the pipes to the required position to align with the hole. For right hand and rear side draw

out, hold the bottom of the piping and ﬁ x direction before shaping it to the desired position

(refer to Figure 2).

Right & Rear Side Routing

Right-back piping

Bind coolant pipe

and drain hose

together with

insulating tape.

Right-bottom

piping

Remove pipe port cover

here for right-bottom piping

Right-side

piping

Remove pipe port cover

here for right-side piping

Remove pipe port cover here for

left-bottom piping

Remove pipe port

cover here for

left-side piping

Left-back

piping

Left-side

piping

Left-bottom piping

Figure 2

Mounting Installation Plate

Paste the installation plan provided on the desired location on the wall and marks the holes location

accordingly.

Ensure the wall is strong enough to withstand the weight of the unit. Otherwise, it is necessary to reinforce

the wall with plates, beams or pillars.

Ensure the levelness of the installation plate, and ﬁ x with 5 suitable screws.

Mounting plate

fixing screw

•

Catalog.indb 14Catalog.indb 14 3/2/2009 4:41:02 PM3/2/2009 4:41:02 PM

15

Application Information MWM-J-2009

Fix the installation plate ﬁ rmly to the wall, without tilting to left or right. Use a plumb line, if available.

Through

the wall

hole

Ø 65mm

Drain

hose

position

Recommended mounting plate

retention spots (5 spots in all)

Use tape measure as shown.

Position the end of a tape measure

at

Gas pipe end

Liquid pipe end

166

184

181.7

55554.5

153.8

263

51.9

800

45.9

42.2

288

42.2

45.9

42.2

All dimensions are in mm

In case of rear piping drawings out, drill a hole 65mm in diameter with a cone drill, slightly lower on the

outside wall.

Inside

Caulking

Outside

Wall embedded pipe

(Field supply)

Wall hole cover

(Field supply)

Wall embedded pipe

(Field supply)

Ø65

Hole with cone drill

Mounting Unit onto the Installation Plate

Hook the indoor unit onto the upper portion of the installation plate (engage the two hooks at the rear top of

the indoor unit with the upper edge of the installation plate). Ensure the hooks are properly seated onto the

installation plate by moving it to the left and right.

To attach the indoor unit, hook the claws of the bottom frame to the mounting plate. If the claws are difﬁ cult

to hook, remove the front grille.

To remove the indoor unit, push the marked area (at the lower part of the front grille) to release the claws.

If it is difﬁ cult to release, remove the front grille.

Mounting

plate

Clip

Mark (rear side)

Bottom frame

Front grille

Mounting plate

Interconnecting

wires

Hang indoor unit's hook here.

Wire guide

When stripping the

ends of interconnecting

wires in advance, bind

right ends of wires with

insulating tape.

•

Catalog.indb 15Catalog.indb 15 3/2/2009 4:41:03 PM3/2/2009 4:41:03 PM

16

MWM-J-2009 Application Information

Water Drainage Piping

The indoor drain pipe must be downward gradient for smooth drainage. Avoid situation as shown in ﬁ gure

below.

End

dipped

into

water

Water

leaking

Water

leaking

Water

leaking

Wrong

Drain

Water Drainage

Water

Retention

Correct

Installation of Outdoor Unit

Condensed Water Disposal of Outdoor Unit (Heat Pump Unit Only)

There are 2 holes on the base of outdoor unit for condensed water to ﬂ ow out. Insert the drain elbow to

one of the holes.

To install the drain elbow, ﬁ rst insert one portion of the hook to the base (portion A), the pull the drain elbow

in the direction shown by the arrow while inserting the other portion to the base. After installation, check to

ensure that the drain elbow clings to base ﬁ rmly.

If the unit is installed in a snowy and chilly area, condensed water may freeze in the base. In such case,

please remove plug at the bottom of unit to smooth the drainage.

A

•

Catalog.indb 16Catalog.indb 16 3/2/2009 4:41:04 PM3/2/2009 4:41:04 PM

17

Application Information MWM-J-2009

As condensing temperature rises, evaporating temperature rises and cooling capacity drops. In order to achieve

maximum cooling capacity, the location selected for outdoor unit should fulﬁ ll the following requirements:

Install the condensing (outdoor) unit in a way such that hot air distributed by the outdoor condensing unit

cannot be drawn in again (as in the case of short circuit of hot discharge air). Allow sufﬁ cient space for

maintenance around the unit.

Ensure that there is no obstruction of air ﬂ ow into or out of the unit. Remove obstacles which block air

intake or discharge.

The location must be well ventilated, so that the unit can draw in and distribute plenty of air thus lowering

the condensing temperature.

A place capable of bearing the weight of the outdoor unit and isolating noise and vibration.

A place protected from direct sunlight. Otherwise use an awning for protection, if necessary.

The location must not be susceptible to dust or oil mist.

Installation Clearance

Outdoor units must be installed such that there is no short circuit of the hot discharge air or obstruction to

smooth air ﬂ ow. Select the coolest possible place where intake air should not be hotter than the outside

temperature (max. 45˚C).

ALL MODELS A B C D

Minimum Distance 300 mm 1000 mm 300 mm 500 mm

CAUTION : If the condensing unit is operated in an atmosphere containing oils (including machine oils), salt (coastal area),

sulphide gas (near hot spring, oil reﬁ nery plant), such substances may lead to failure of the unit.

•

Catalog.indb 17Catalog.indb 17 3/2/2009 4:41:06 PM3/2/2009 4:41:06 PM

Page is loading ...

McQuay M5WM015JR User manual

This manual is also suitable for

McQuay M5WM015JR User manual

Related papers

Other documents