Windster WS-38U48SS Specification

Brand: Windster

Model: WS-38U48SS

Category: Cooker hoods

Type: Specification

This manual is also suitable for

WS38U30SS

Windster WS-38U48SS is a range hood designed for residential and indoor use. It comes with a variety of features to help you keep your kitchen clean and free of fumes and odors.

The WS-38U48SS has a powerful motor that can move up to 480 cubic feet of air per minute, which is enough to handle even the most demanding cooking tasks. It also has three fan speeds, so you can adjust the airflow to your needs. This range hood can be vented vertically or horizontally, giving you the flexibility to install it in a variety of locations.

The WS-38U48SS also comes with two baffle filters that are easy to remove and clean. These filters are designed to capture grease and other particles, helping to keep your kitchen air clean. The range hood also has a built-in LED light that provides bright illumination for your cooking area.

Windster WS-38U48SS is a range hood designed for residential and indoor use. It comes with a variety of features to help you keep your kitchen clean and free of fumes and odors.

OPERATION

Pleasereadandsavethis guidethroughbeforeusingyourrangehood.

Storetheguideaway inasafeplacesothatyouwillknowwhereitis,

whenyouwanttorefertoit.

WS-38U30SS

WS-38U36SS

WS-38U42SS

WS-38U48SS

MANUAL

(Forresidentialandindooruseonly)

TableofContents

Important Safety Instructions ----------------------------

Safety Notes -------------------------------------------------

Tools and Materials Required -----------------------------

Accessory Package -----------------------------------------

Preparing the Range Hood --------------------------------

Preparing the Installation Location -----------------------

Providing Electrical Power ---------------------------------

Remove and Reinstall Baffle filters ----------------------

Maintenance Instruction ----------------------------------

Ducting -------------------------------------------------------

Vertical Rectangular Ducting -----------------------------

Rear Rectangular Ducting ---------------------------------

Mounting Range Hood to Cabinet ------------------------

Mounting Range Hood Without Cabinet ----------------

Making the Electrical Connection -------------------------

Use and Care -------------------------------------------------

Troubleshootings --------------------------------------------

Replace The LED Light --------------------------------------

Parts Layout Diagram ---------------------------------------

Circuit Diagram ----------------------------------------------

Recirculation Kit Installation ------------------------------

Bodysize-------------------------------------------------------

P.1

P.3

P.4

P.5

P.6

P.7

P.8

P.9

P.10

P.11

P.13

P.14

P.16

P.19

P.20

P.22

P.23

Duetosharpedge,pleasewear SafetyWorkmanGloves"

forinstallation,cleaning,lightbulbchangingand

dismantlingtoreducetheriskofanybodilyinjuries.

SafetyWorkmanGloves

WARNING

CAUTION-Toreduceriskoffireandtoproperlyexhaustair,makesuretoproperly

exhaustair.Besuretoductairoutside-Donotventexhaustairinto

spaceswithin walls,ceilings,attics,crawlspaces,orgarages.

WARNING-Toreducetheriskoffireorelectricshock,donotusethisfanwithany

solid-statespeedcontroldevice.

WARNING-

A.DONOTsprayanyliquidformcleaneronhoodsurfaceincludinglights

andcontrolswitch.Tocleantherangehood,sprayliquidformcleaner

directlyontocleaningclothforhoodcleaning.

B.Usethisunitonlyinthemannerintendedbythemanufacturer.

Ifyouhavequestions,contactthemanufacturer.

C.Beforeservicingorcleaningtheunit,switchpoweroffatservicepanel

topreventpowerfrombeingswitchedonaccidentally.

D.When theservicedisconnectingmeanscannotblocked,securely

fastenprominentwarningdevicesuchasatagtoservicepanel.

TOREDUCETHERISKOFFIRE,ELECTRICSHOCK,ORINJURY,

TOPERSONS,OBSERVETHEFOLLOWING:

CAUTION-Forgeneralventilatinguseonly.Donotusetoexhausthazardous

orexplosivematerialsandvapours.

WARNING-

A-Neverleavesurfaceunitsunattendedathighsettings.Boilovercause

smokingandgreasyspilloversthatmayignite.Heatoilsslowlyonlow

or mediumsettings.

B-Alwaysturnhoodonwhencookingathighheatorwhencookingflaming

foods.(ie,Craepessuzetter,charriesjubilee,peppercornbeefflambe)

C-Cleanventilatingfansfrequently.Greaseshouldnotbeallowedto

accumulateonfanorfilter.

D-Useproperpansize.Always usecookwareappropriateforthesizeofthe

surfaceelement.

TOREDUCETHERISKOFARANGETOPGREASEFIRE:

A.ImportantSafetyInsturctions

WARNING-Toreducetheriskofinjuryintheeventofarangetopgrease

fire,observethefollowing:

A- withaclose-fittinglid,cookiesheet,

ormetaltray,then turnofftheburner.Becarefultoprevent

burns.Iftheflamesdonotgooutimmediately,

SMOTHERFLAMES

EVACUATE

ANDCALLTHEFIREDEPARTMENT.

D-

1.Youknowyouhavea extinguisher,andyou

alreadyknowhowtooperateit.

2.Thefireissmallandcontainedintheareawhereitstarted.

3.Thefiredepartmentisbeingcalled.

4.Youcanfightthefirewithyourbacktoanexit.

USEANEXTINGUISHERONLYIF:

CLASSABC

C- includingwetdishclothsortowels-

aviolentsteamexplosionwillresult.

DONOTUSEWATER

B- -Youmaybeburned.NEVERPICKUPAFLAMINGPAN

WARNING-Sufficientairisneededforpropercombustionand

exhaustingofgasesthroughtheflue(chimney)offuelburning

equipmenttopreventbackdrafting.Followtheheatingequipment

manufacturer'sguidelineandsafetystandardssuchasthese

publishedbytheNationalFireProtection Association(NFPA),and

theAmericanSocietyforHeating.RefrigerationandAir

ConditioningEngineers(ASHRAE),andthelocalcodeauthorities.

Keeptherangehoodclean.

WARNING-Toreducetheriskoffire,useonlymetalductwork.

1.Allelectricalworkmustbedoneinaccordancewithlocaland/ornational

electricalcodeasapplicableforsafety.Thisproductmustbegrounded

ifyourareunfamiliarwithmethodsofinstallingelectricalwiring,secure

theservicesofaqualifiedelectrician.

2.Turnoffpoweratserviceentrancebeforeinstallingwiringorservicing

thisproduct.(120voltforrangehood.220voltforelectricrangeifany)

3.Turnoffpowertoavoidriskoffire,electricshock,orinjuryforcleaning

ormaintenancesuchaslubrication.

4.Fireplaces,gasfurnaces,waterheaters,requireproperflowof

combustionairandexhaust.Makesurethisflowisnotalteredwhen

usinganyexhaustfan.

5.Pleasereadspecificationlabelonproductforfurtherinformationand

requirements.

CAUTION-Toreducetheriskoffireandtoproperlyexhaustair,be

suretoductairoutside.Donotventexhaustairintospaces

withinwallsorceilingsorintoattics crawlspacesorgarages.

6.Pleasewear"SafetyGloves"forinstallation,cleaning,lightbulb

changinganddismantlingtoreducetheriskofanyinjuries.

B.SafetyNotes

Drill,electricofratchetdriver,with3/16"woodbit(fordrillingstarter

holesand1 ” woodbit(todrillanaccessholesinthecabinetor

kitchenwallfortheelectricpowerline)

Plier(foropeningelectricalknockout).

Two1"(thick)x2"(wide)x12"(approximatelength)woodstripsfor

recessedbottomkitchencabinetinstallationonly.(Purchaselocally).

Electricalwireandsuppliestocomplywithlocalcords.

Four1 ” longflatheadwoodscrews(purchaselocally)tomount

woodstrips.

Pencilandrulerformarkinglocations.Sabersaworkeyholesawfor

cuttingthe1"x2"woodstripstolength.

1.Woodscrews3/16" x1"L6pcs.

2.Wireconnectorwithspring3pcs.

3.Washer 6pcs.

Onecommonscrewdriver.

C.ToolsandMaterialsRequired

D. AccessoryPackage

4.6”/7” Verticalstartingroundcollar1pc.

ElectricalKnockout

1.Removethetopelectrical

knockout,youmayplanto

bringpowertotherange

hoodeitherthroughthe

cabinetorthroughthewall

(Fig.1)

2.Insertascrewdriverintotheknockoutslotandbendtheknockout

backandforth.(Fig.2)

3.Youmayhavetouseplierstopulltheloosenedknockoutfree.(Fig.3)

4.Wheninstalled,thebottomedge

ofyourrangehoodshouldbe

28"~32"abovethetopofthe

cookingsurface.(Fig.4)

Fig.2

Fig.3

E.PreparingTheRangeHood

Fig.1

Fig.4

28”-32”

1.Ifyouwanttomovetheelectricrangetomakeroomforworkingonthecabinet

turnoffthe220voltpowerfortheelectricrangeattheserviceentrance.

2.Beforemovingagasrange,shutoffthegas.

NOTE:SKIPFOLLOWINGSTEPS3ATHROUGH3DIFTHEHOODISTOBE

MOUNTEDONACABINETWITH .AFLUSHBOTTOM

3.Forinstallationontoarecessedbottomcabinet:

a.Measurethespace(underthecabinetbetweentheinsidefrontedgeand

insidebackedge(Fig.5).Withasabersaw,cuttwo1"x2"woodfillerstrips

(purchasedlocally)tofillinthebottomofthecabinet.

b.Starta1 "longwoodscrew(purchasedlocally)about3"fromeachend

ofthe1"x2"woodstrips(Fig.6)

c.Positionthestripsonthecabinetbottomandscrewthestripssecurelyto

thecabinet(Fig.7)

d.Foramoresecureinstallation,drillfour3/16"holesfrominsidethecabinet,

downintothewoodfillerstrips.Insertscrewsintothestarterholesin

cabinetandtightenscrewsuntilwoodfillerstripsaresecuredundercabinet.

4.Centerthehoodinplacebeneaththecabinetandflushwiththefrontofthe

cabinet.Markthefollowing:

a.Thesixkeyholemountingslotsforthehood. Marktheseontothebottomof

thecabinet;or,ifthecabinetbottomisrecessed.Ontothewoodstrips(Fig.7)

b.Theelectricalknockouthole.(Fig.1)

Fig.5

Fig.6

F.PreparingTheInstallationLocation

C.Screwthefour1"woodscrews(for

mountingthehood)intotheexact

centerofthearrowandintothekeyhole

mountingslotsmarkedonthecabinet

bottom(forflushinstallations),or

markedonthe1”

recessedcabinetinstallation)(Fig.7)

Donotturnthemountingscrewsinall

theway.Allow3/8"ofscrewtoproject,

sothehoodcanbefittedplace.

(Thescrewswillbetightenedlater)

x2” woodstrips(for

Ifdrillingintothewalls,becarefulnottocutexistingelectricalcables,

whichwouldcreateahazard.

Fig.9

Fig.8

1.Afterturningofftheproper120voltcircuitattheserviceentrance,

drillouttheelectricalpowerlineaccessholemarkedonthecabinet

bottom orwall.Usea1 ”woodbit.(Fig.8)¼

Color:

green/white/black

Connecter

1"bit

Fig.7

G.ProvidingElectricalPower

SafetyWarning:

2.Fishtheelectricalpowerlinethroughtheaccessholedrilledinthewallor

bottomofthecabinet.Attachanappropriateconnector(purchasedlocally)

totheendofthepowerlineforthetypeofwiringbeinginstalled.Followall

codes.(Fig.9)

Stripssecured

4.Pickuptheinneroilcollector.

NOTE:ReinstallingBafflefilters.ReversethestepsasremovingBafflefilters.

Formountingundercabinet

1.AfterabovestepH,thencontinuethefollowingsteps.

2.Remove2screwsonthespacer(s).

3.Removespacer(s).

4.Keyholetomounttoundercabinet.

①

②

! !

1.Wearsafetyworkmanglovesand

holdthehandlesofBafflefilter.

2.PushBafflefilterdownward

①,

then pull a little back ②

3.LiftuptheBafflefilter .③

Keyhole

H.RemoveandReinstallBafflefilters

③

2.Afterusingthemachine,wipesthemachinebyneutraldetergentin

ordertokeepitcleanandmaintaintheappearancewithbrightness

andsanitation.

3.Whenthelevelofdirtyoilofthecollectorreached4/5ofheight,ithasto

beremovedinordertoavoidoverflowingandpollution.

Thisstyleofrangemustbeventedviaductingtotheoutsideofthehouse.

Followgeneralruleswhenductingthehood:Usecorrectsizeofducting

(6"or7” round),donotreducesizeofducting,makeallturnsgradual,

noshortcorners.Ifductingranwillbelongerthan10feetenlargeductby

atleast1"inchdiameteraftereach10feet.Tapealljointsinductingand

allgasketedopeningsonhoodforatightseal.

Loosen2screws(Ref.1),fitthegrayplasticroundcollar/6” overthecircular

openingontop(Ref.2)andfasten2screws(included)inordertoprovideatight

sealforductingtoattachto(Ref.3),ifyouwant touse7” ducting,take7” converter

(included)tojointogetherwiththe6” roundcollar(Ref.4).

Forroundductingfromthetop:

I.MaintenanceInstruction

J.Ducting

1.Maintenanceshallbeimportantthanrepair.Pleasetakecareofthe

neededmaintenanceinordertosecureandextendtheexcellent

functionsandusinglife.

Note:Beforerepairingtherangehood.Disconnectthepowersource.

1 2 3 4

! ! !

Loosen2screws Fit6"collar

Fit 7” converter

Fasten2screws

Fasten

Loosen

F. Completelyfinished.

A.Removethepre-mounted

6” roundductopening.

B.Puttransitionplatebyfirst

installing onthe

halfroundsection.

(Optional)

4screws

C.Taketherectangularstarting

collar.(Optional)

D.Overlaptherectangular

startingcollaronthetop

oftransitionplate.

E.Mountingrectangularstarting

collarwithremainingscrews.

K.VerticalRectangularDucting

Anoptionalkitforvertical

rectangularducting:

NOTE:

Transitionplate

Rectangular

startingcollar

(Small)

Halfroundsection

A.Removethepre-mounted

6” roundductopening.

B.Puttransitionplatebyfirst

installing on

thehalfroundsection.

(Optional)

4screws

C.Useslottedscrewdriver,

(orwhateverflathead)

toknockoutthepre-mounted

rearrectangularcap.

D.Pre-mounted

rectangularplate.

E.Removethepre-mounted

rectangularplate.

L.RearRectangularDucting

-tobecontinued-

F.Takethepre-mounted

rectangularplate.

H.Insertappropriaterectangular

startingcollar(optional)

(2differentsize)

¼ ¾ (LxWxH)

11¼” x3¾” x3 (LxWxH)

ⓐ

ⓑ ⅛"

11 " x 3 " x 1"

I.Mountrectangular

startingcollar.

( ¼ ¾ )

(optional)

11 " x 3 " x 1"

G.Mounttherectangular

plate(previousremoved)

ontopoftransitionplate.

J.Rectangularstartingcollar.

(11¼” x3¾” x3 LxWxH)

(optional)

⅛"

L.RearRectangularDucting

Anoptionalkitforrear

rectangularducting:

NOTE:

Transitionplate

Rectangular

startingcollar

(Small)

(Large)

(Small) (Large)

1.Positionthehoodinplacesothat:

2.Adjustthehoodsothefrontisflushwiththecabinetfront.

a.TheelectricallineisroutedthroughtheappropriateKnockout

opening.Thisstepwillhavetobeaccomplishedwhilepositioning

thehood(Fig.10)

b.Thelargepartofthekeyholemountingslotsonthehoodfitonto

thehoodmountingscrewsprojectingfromthebottomofthe

cabinet.(Fig.11)

3.Tightenthehoodmountingscrewsallthewayintothecabinetorinto

the1" x2"woodstripssothehoodissecure.

Fig.10

Color:

green/white/black

Knockoutopening

M.MountingRangeHoodToCabinet

Fig.10

Fig.11

NOTE:Read “ RemoveandReinstallBafflefilter” & “ Formountingundercabinet”

onpage8.

1.Usingmetalbracketsandscrews

(included),centerhoodonto

boardandinstallscrew.

2.Removethehoodfromtheboardand

nailthewoodboardontothewall.

(Besurethenailisinthecenterof

thestud)

3.Placetherangehoodontheboard

andtightenthescrew.

Bracket

Screw

4.Completelyfinished

N.MountingRangeHoodWithoutCabinet

Install the range hood

to the desired position

Check and fix the

ower chimney

bracket

1. Set 6” round ducting

collar or

2. Set rectangular starting

collar (check manual)

Check the desired length of

chimney and mark the position

for upper chimney bracket then

fixed. each section 19-1/2” (50cm)

in length maxi extention length

38” (96.5cm)

Install the 6” piping tube or

7” piping tube (Ref fig 3-2

use converter), or rectangular

piping exhaust outlet.

all piping tubes are not

included.

Note:

1 2 3-1

3-2

7” round converter collar

(for 7” exhaust piping)

" " "

Tape all joints in ducting and all gasketed opening on hood for a tight seal.

Note:

Slide the chimney

(upper + lower)

into the base

Check 2 screw holes

Fasten 2 screws

8 9

Extend the upper chimney

up to the desired position

Check 2 screw holes

and fastened

(complete finished)

1.Duct cover and extension duct cover fitment may vary depend on the mounting height of

the range hood.

2.Make sure you can easily peel the white protection pvc film after installation, otherwise

please peel it before chimney installation.

Note:

o o r

ChimneyInstallationChart(optional)

Mountingrangehoodwithoutcabinet

1.RemovestainlessBafflefilters.(Ref.P8-H)

2.Removescrewsonwiringcase,

fishoutwiresthroughthe

knockout.(Fig.12)

3.Marktheelectricalconnectionby

fasteningallwirestotheexisting

wallwiringaccordingtothetheir

colors.(BlacktoBlack,Whiteto

White,GreentoGround)

4.Afterconnectionisdone,reinstallwiringcasecoverandbottomboard.

5.Turnonpowerandcheckoperationoffanandlight.

P.MakingTheElectricalConnection

Q.UseandCare

Fig.12

wirecase

A.Bypressing,allfunctionsarestand-by.

B.Bypressingagain,allfunctionswillbeturnedoff.

Mainpowerbutton

NOTE: ALL FUNCTIONSCANBEWORKEDONLY UNDERTHE

MAINPOWERISON.

OFF

Nightlightsensor

Mainpower

FanOFF

LEDlight

3speedfanselection

6.Aftercompletelyinstallation,reinstallthestainlessBafflefilterandoilcollector.

(Ref.P8-H)

:Fanspeedselectionandfanoff.

A. :Whenthemainpowerbuttonisbeingpressed,bypressing

button//fordesiredfanspeed.

-slowspeed

-mediumspeed

-highspeed

B. :Toturnoffthefan,justpressthebutton,orpressoff

themainpowerbutton.

UseforFan

FanON

FanOFF

NOTE:a.Thefanspeedcanbeinterchangedbypressinganyoneofabove

3buttons,however.

b. NEVERPRESS ANY OFTWOBUTTONSIN A TIME.

OFF

NOTE:

A.PresstoturnontheLEDlight.

B.PressagaintorturnofftheLEDlight.

NOTE:

UseforLight

Usefor Auto-sensorLEDnightlight

MAKESURETHEMAINPOWERBUTTONISPRESSEDBEFORE

TURNINGONTHELEDLIGHT.

MAKESURETHE MAINPOWERBUTTONISPRESSEDBEFORE

TURNINGONTHELEDLIGHT.

A.Theauto-sensorofLEDnightlightwillbeautomaticallyturnonat20%

brightnesscomparetooriginalwhenthesurroundingsisgettingdarker

(ordark).

B.Whenthesurroundingsisgettingbrighter(orbright),theauto-sensor

willturnthenightlightoffautomatically.

C.Toturnofftheauto-sensornightlightbutton,aftercookingturnsoffthe

mainpowerbutton.Tokeepthisfunction,remainthemainpower

buttonalwaysON.

Note:

CareInstruction:

Rangehoodshouldbeturnoneitherbeforeorthesametimewhencooking

begins.Aftercooking,rangehoodshouldbekeptonforabout3moreminutes

forcompleteventilationofcookingodor.

Pleasealwayspulltheplugoutbeforecleaningordismantling,wear

Safetygloves toreducetheriskofanyinjuries." "

Exterior:Canbecleanedwithanytypeofnon-abrasivedetergentanda

cleancloth. GreenPad oranymetaltypecleaningpadis

notrecommendedforexterior.

" "

Asthosemayscratchthe

graphicwordingsoncontrolpanel.

Interior:1.SwitchONthefanatHigh,mixmilddetergentwithwaterin

mist-sprayer,atfine-spraymixtureontothebladesfor60seconds

withthefanrunning.(mistsprayerisnotincluded)

2.Leavefanonforanadditional3minutestodryoilbasin.

3.Repeatonotherturbinevane(canbecleanedsimultaneously

withthefirst).

Page is loading ...

Windster WS-38U48SS Specification

Brand: Windster

Model: WS-38U48SS

Category: Cooker hoods

Type: Specification

This manual is also suitable for

WS38U30SS

Windster WS-38U48SS is a range hood designed for residential and indoor use. It comes with a variety of features to help you keep your kitchen clean and free of fumes and odors.

Download PDF

report

Windster WS-38U48SS Specification

This manual is also suitable for

Windster WS-38U48SS Specification

Related papers