Page is loading ...
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
.
2
Press [BAND] (SET) to
set.
∫ SUB WOOFER
E
N
G
L
I
S
H
22
CQ-DFX972U
37
E
N
G
L
I
S
H
21
CQ-DFX972U
36
Audio Settings [AUDIO]
Note:
≥ Operations except setting should be performed after
returning to the mode display.
≥ Press [MENU], [DISP] (display) to return to the reg-
ular mode.
BAS
(Bass)
TRE
(Treble)
1 Press [TUNE $] or [TUNE %]/[$] or [%] to select “BAS”.
2 Press [P·SET "]/["]: Increases the bass.
Press [P·SET #]/[#]: Decreases the bass.
1 Press [TUNE $] or [TUNE %]/[$] or [%] to select “TRE”.
2 Press [P·SET "]/["]: Increases the treble.
Press [P·SET #]/[#]: Decreases the treble.
BAL
(Balance)
FAD
(Fader)
Press [TUNE $]/[$]: Right enhanced.
Press [TUNE %]/[%]: Left enhanced.
Press [P·SET "]/["]: Front enhanced.
Press [P·SET #]/[#]: Rear enhanced.
Press [P·SET "] or [P·SET #]/["] or [#] to change setting.
1 Press [P·SET "] or [P·SET #]/["] or [#] to select “LEVEL”.
2 Press [TUNE $]/[$]: Increases the level.
Press [TUNE %]/[%]: Decreases the level.
1 Press [P·SET "] or [P·SET #]/["] or [#] to select “LPF”.
2 Press [TUNE $] or [TUNE %]/[$] or [%] to select “120 Hz” or
“80 Hz”.
3 Setting
Bass and Treble
You can adjust the bass and treble sound.
Default: BAS (Bass) 0
TRE (Treble) 0
Setting range: j12 to i12 (by 2 steps)
Subwoofer Level
You can change the subwoofer volume level.
Default: 0
Setting range: j∞ (Subwoofer mute),
j6 to i6 (by 2 steps)
Subwoofer Low Pass Filter
Select the upper limit frequency of the sound
from subwoofer.
Default: 120 Hz Setting range: 120 Hz/80 Hz
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
.
2 Press [BAND] (SET)
to set.
∫ S·HDB
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
.
2 Press [BAND] (SET)
to set.
∫ BAS/TRE
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
.
2 Press [BAND] (SET)
to set.
∫ BAL/FAD
Balance and Fader
You can adjust the sound balance among
the front, rear, right and left speakers.
Default: BAL (Balance) Center
FAD (Fader) Center
Setting range: 15 levels each
12
Audio menu display
Menu Submenu
S·HDB (Super High
Definition Bass)
Especially for rock music, the bass-sound
will be more powerful.
Default: OFF
Setting range: OFF, BOOM, TIGHT
: The bass sounds of the speakers are
strongly emphasized.
: The bass sounds of the speakers are
moderately emphasized. (The sounds of
the subwoofer can be heard clearly.)
: S·HDB is non-active.
Note:
≥ When S·HDB is on, the indicator (S·HDB
BOOM or TIGHT) is shown on the audio indi-
cator display. (➡ page 19)
[DISP] (Display)
[MENU]
[BAND] (Setting)
[P·SET #] [P·SET "] (Submenu/setting)
[TUNE $] [TUNE %] (Menu/setting)
SRC
DISP
P
.
SET/DISC
CQ-DFX972U
N
5
O
6
W
X
;
/ 1
OPEN
BAND
TUNE
TRACK
P
W
R
MUTE
PU
SH
CD RECEIVER WITH FULL DOT MATRIX DISPLAY
FOLDER
SET/APM
M
E
N
U
VO
LU
M
E
S
OU
R
CE
T E X T
MOSFET
50W X 4
64
97
5
Car Audio
SOURCE
MUTE
POWER
RAND
VOL
312
DISPBAND
REP
6
5
SET
SEL
#
SCAN
MENU
NUMBER
8
0
[SEL]
(MENU)
["] [#]
(Submenu/setting)
[%] [$]
(Menu/setting)
[BAND]
(SET)
[DISP] (Display)
Note:
≥ When subwoofer level is set “j∞”, the indicator (SUB·W) is not
shown on the audio indicator display. (➡ page 19)
P
U
S
H
M
E
N
U
VOLUM
E
1 Press [MENU]/[SEL]
(MENU).
2 Press [TUNE $] or
[TUNE %]/[$] or [%] to
select
“AUDIO” tab.
(Press.)
E
N
G
L
I
S
H
24
CQ-DFX972U
39
E
N
G
L
I
S
H
23
CQ-DFX972U
38
Picture (Display) Settings [PICTURE]
Press [TUNE $] or [TUNE %]/[$] or [%] to change setting.
Press [TUNE $]/[$]: Decreases the contrast.
Press [TUNE %]/[%]: Increases the contrast.
: Display showing a cube that continues to
change.
: Display showing a globe that continues
to change.
: Display showing the image of a skate-
board.
C
B
A
Note:
≥ Change the display to show the Spectrum Analyzer (S·A) dis-
play. (➡ page 19)
: Display showing text pattern.
: Display showing the image of a circuit.
: Standard spectrum analyzer display
(9 bands).
STD
E
D
: Clock display ON
: Clock display OFF
OFF
ON
Note:
≥ Operations except setting should be performed after
returning to the mode display.
≥ Press [MENU], [DISP] (display) to return to the reg-
ular mode.
Clock display
3 Setting
2 Press [BAND] (SET) to set.
Spectrum Analyzer (S
·
A)
Display Pattern
Default: A
Variety: 6 types
Contrast
Allows you to adjust the display contrasts
for better viewing.
Default: 3
Setting range: 1 to 5
Clock on the Mode Display
Default: ON
(“jj:jj” will appear before
adjusting the clock.)
(Clock adjustment ➡ page 40)
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
.
2 Press [BAND] (SET)
to set.
∫ S·A PATTERN
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
.
2 Press [BAND] (SET)
to set.
∫ CONTRAST
Picture (display) menu display
1 Menu 2 Submenu
Dimmer (display brightness
setting range)
Default: 3
Setting range: 1 to 3
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
.
2 Press [BAND] (SET)
to set.
∫ DIMMER
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
Press [TUNE $] or [TUNE %]/[$] or [%] to change setting.
: Bright
: Medium
: Dark
1
2
3
[DISP] (Display)
[MENU]
[BAND] (Setting)
[P·SET #] [P·SET "] (Submenu/setting)
[TUNE $] [TUNE %] (Menu/setting)
SRC
DISP
P
.
SET/DISC
CQ-DFX972U
N
5
O
6
W
X
;
/ 1
OPEN
BAND
TUNE
TRACK
P
W
R
MUTE
PU
SH
CD RECEIVER WITH FULL DOT MATRIX DISPLAY
FOLDER
SET/APM
M
E
N
U
VO
LU
M
E
S
OU
R
CE
T E X T
MOSFET
50W X 4
64
97
5
Car Audio
SOURCE
MUTE
POWER
RAND
VOL
312
DISPBAND
REP
6
5
SET
SEL
#
SCAN
MENU
NUMBER
8
0
[SEL] (MENU)
["] [#]
(Submenu/setting)
[%] [$]
(Menu/setting)
[BAND] (SET)
[DISP] (Display)
∫ CLOCK-ON
∫ CLOCK-OFF
P
U
S
H
M
E
N
U
VOLUM
E
1 Press [MENU]/[SEL]
(MENU).
2 Press [TUNE $] or
[TUNE %]/[$] or [%] to
select
“PICTURE” tab.
(Press.)
Increase Decrease
1 Press [P·SET "] or
[P·SET #]/["] or
[#] to select
.
2 Press [BAND] (SET)
to set.
∫ CLOCK ADJ
E
N
G
L
I
S
H
26
CQ-DFX972U
41
E
N
G
L
I
S
H
25
CQ-DFX972U
40
Clock Basics
Press [BAND] (SET) to change setting.
: No sound.
: Decrease the volume to
1
/
10.
(Attenuation)
ATT
MUTE
Press [BAND] (SET) to change setting.
: Security function is active.
: Security function is non-active.
OFF
ON
Security Function
When the key in the ignition is turned OFF.
≥ Security message will be active.
≥ The panel removable alarm will be active.
When the removable face plate is removed.
≥ The security indicator blinks. (➡ page 57)
3 Setting
Mute/Attenuation
You can select how much to lower the
volume when [MUTE] is pressed.
Default: MUTE
Security Function
The security indicator blinks when the re-
movable face plate is removed from the
unit.
Default: ON
Press [P·SET "] or
[P·SET #]/["] or [#]
to select
.
∫ MUTE KEY
Press [P·SET "] or
[P·SET #]/["] or [#]
to select .
∫ S-LED
Function menu display
1 Menu 2 Submenu
3 Setting1 Menu 2 Submenu
Clock Adjustment
(12 hour system)
Default: “ADJUST” (not adjusted.)
Function Settings [FUNCTION]
Note:
≥ Operations except setting should be performed after
returning to the mode display.
≥ Press [MENU], [DISP] (display) to return to the reg-
ular mode.
Hours
set.
Minutes
set.
1 [TUNE %]/[%]: The hour display highlights.
2 [P·SET "]/["]: Put forward.
[P·SET #]/[#]: Put back.
1 [TUNE $]/[$]: The minutes display highlights.
2 [P·SET "]/["]: Put forward.
[P·SET #]/[#]: Put back.
Highlighted.
[DISP] (Display)
[MENU]
[BAND] (Setting)
[P·SET #] [P·SET "] (Submenu/hour/minute)
[TUNE $] [TUNE %] (Menu/setting)
SRC
DISP
P
.
SET/DISC
CQ-DFX972U
N
5
O
6
W
X
;
/ 1
OPEN
BAND
TUNE
TRACK
P
W
R
MUTE
PU
SH
CD RECEIVER WITH FULL DOT MATRIX DISPLAY
FOLDER
SET/APM
M
E
N
U
V
O
LU
M
E
SO
U
RCE
T E X T
MOSFET
50W X 4
64
97
5
Car Audio
SOURCE
MUTE
POWER
RAND
VOL
312
DISPBAND
REP
6
5
SET
SEL
#
SCAN
MENU
NUMBER
8
0
[SEL] (MENU)
["] [#]
(Submenu/hour/minute)
[%] [$]
(Menu/setting)
[BAND] (SET)
[DISP] (Display)
P
U
S
H
M
E
N
U
VOLUM
E
P
U
S
H
MENU
VOLUME
1 Press [MENU]/[SEL]
(MENU).
2 Press [TUNE $] or
[TUNE %]/[$] or [%] to
select
“PICTURE” tab.
(Press.)
1 Press [MENU]/[SEL]
(MENU).
2 Press [TUNE $] or
[TUNE %]/[$] or [%] to
select
“FUNCTION” tab.
(Press.)
3 Press [BAND] (SET) to set.
/