2. Industrial & lab equipment
  3. Electrical equipment & supplies
  4. Electrical connection
  5. Electrical connector assemblies
  6. Metra
  7. XSVI-9003

Metra XSVI-9003 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Metra XSVI-9003 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
In
the VW vehicles listed below there are no 12 volt
accessory wires currently in the factory harness mak-
ing the installer run an accessory wire to the fuse box
o
r underneath the steering column when installing an
aftermarket radio. The XSVI-9003 is designed to pro-
vide a 12 volt 10 amp switched accessory output
a
long with the rest of the wires needed to install an
aftermarket radio. The R.A.P. (Retained Accessory
Power) function, where power is supplied to the radio
a
fter the ignition is shut off until one of the front doors
are opened, is retained by the XSVI-9003.
I
NITIALIZE THE XSVI INTERF
A
CE BEFORE TURNING
ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key
to the ON position for thirty seconds, then turn key
off.
Wiring the XSVI-9003:
Wiring up the XSVI-9003 is
like wiring up any other wire harness that would
attach to the aftermarket radios harness. The
Metra/EIA wire code can be found on the back of this
package that will aid you in the wiring of your after-
market radio.
(See Applications on back of page)
REV. 06/12/07 INSTXSVI-9003
1-800-221-0932 www.metraonline.com
METRA ELECTRONICS CORPORATION
© COPYRIGHT 2007
XSVI-9003
INSTALLATION INSTRUCTIONS
In
the VW vehicles listed below there are no 12 volt
accessory wires currently in the factory harness mak-
i
ng the installer run an accessory wire to the fuse box
o
r underneath the steering column when installing an
aftermarket radio. The XSVI-9003 is designed to pro-
v
ide a 12 volt 10 amp switched accessory output
along with the rest of the wires needed to install an
aftermarket radio. The R.A.P. (Retained Accessory
P
ower) function, where power is supplied to the radio
after the ignition is shut off until one of the front doors
a
re opened, is retained by the XSVI-9003.
INITIALIZE THE XSVI INTERFACE BEFORE TURNING
ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key
to the ON position for thirty seconds, then turn key
off.
Wiring the XSVI-9003: Wiring up the XSVI-9003 is
like wiring up any other wire harness that would
attach to the aftermarket radios harness. The
Metra/EIA wire code can be found on the back of this
package that will aid you in the wiring of your after-
market radio.
(See Applications on back of page)
REV. 06/12/07 INSTXSVI-9003
1-800-221-0932 www.metraonline.com
METRA ELECTRONICS CORPORATION
© COPYRIGHT 2007
XSVI-9003
INSTALLATION INSTRUCTIONS
In
the VW vehicles listed below there are no 12 volt
accessory wires currently in the factory harness mak-
i
ng the installer run an accessory wire to the fuse box
o
r underneath the steering column when installing an
aftermarket radio. The XSVI-9003 is designed to pro-
v
ide a 12 volt 10 amp switched accessory output
along with the rest of the wires needed to install an
aftermarket radio. The R.A.P. (Retained Accessory
P
ower) function, where power is supplied to the radio
after the ignition is shut off until one of the front doors
a
re opened, is retained by the XSVI-9003.
INITIALIZE THE XSVI INTERFACE BEFORE TURNING
ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key
to the ON position for thirty seconds, then turn key
off.
Wiring the XSVI-9003: Wiring up the XSVI-9003 is
like wiring up any other wire harness that would
attach to the aftermarket radios harness. The
Metra/EIA wire code can be found on the back of this
package that will aid you in the wiring of your after-
market radio.
(See Applications on back of page)
REV. 06/12/07 INSTXSVI-9003
1-800-221-0932 www.metraonline.com
METRA ELECTRONICS CORPORATION
© COPYRIGHT 2007
XSVI-9003
INSTALLATION INSTRUCTIONS
In
the VW vehicles listed below there are no 12 volt
accessory wires currently in the factory harness mak-
i
ng the installer run an accessory wire to the fuse box
o
r underneath the steering column when installing an
aftermarket radio. The XSVI-9003 is designed to pro-
v
ide a 12 volt 10 amp switched accessory output
along with the rest of the wires needed to install an
aftermarket radio. The R.A.P. (Retained Accessory
P
ower) function, where power is supplied to the radio
after the ignition is shut off until one of the front doors
a
re opened, is retained by the XSVI-9003.
INITIALIZE THE XSVI INTERFACE BEFORE TURNING
ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key
to the ON position for thirty seconds, then turn key
off.
Wiring the XSVI-9003: Wiring up the XSVI-9003 is
like wiring up any other wire harness that would
attach to the aftermarket radios harness. The
Metra/EIA wire code can be found on the back of this
package that will aid you in the wiring of your after-
market radio.
(See Applications on back of page)
REV. 06/12/07 INSTXSVI-9003
1-800-221-0932 www.metraonline.com
METRA ELECTRONICS CORPORATION
© COPYRIGHT 2007
XSVI-9003
INSTALLATION INSTRUCTIONS
In the VW vehicles listed below there are no 12 volt
accessory wires currently in the factory harness mak-
ing the installer run an accessory wire to the fuse box
or underneath the steering column when installing an
aftermarket radio. The XSVI-9003 is designed to pro-
vide a 12 volt 10 amp switched accessory output
along with the rest of the wires needed to install an
aftermarket radio. The R.A.P. (Retained Accessory
Power) function, where power is supplied to the radio
after the ignition is shut off until one of the front doors
are opened, is retained by the XSVI-9003.
INITIALIZE THE XSVI INTERFACE BEFORE TURNING
ON RADIO:
With all connections made and har-
nesses connected to the vehicle, turn ignition key
to the ON position for thirty seconds, then turn key
off.
Wiring the XSVI-9003:
Wiring up the XSVI-9003 is
like wiring up any other wire harness that would
attach to the aftermarket radios harness. The
Metra/EIA wire code can be found on the back of this
package that will aid you in the wiring of your after-
market radio.
(See Applications on back of page)
REV. 06/12/07 INSTXSVI-9003
1-800-221-0932 www
.metraonline.com
METRA ELECTRONICS CORPORATION
© COPYRIGHT 2007
XSVI-9003
INSTALLATION INSTRUCTIONS
In the VW vehicles listed below there are no 12 volt
accessory wires currently in the factory harness mak-
ing the installer run an accessory wire to the fuse box
or underneath the steering column when installing an
aftermarket radio. The XSVI-9003 is designed to pro-
vide a 12 volt 10 amp switched accessory output
along with the rest of the wires needed to install an
aftermarket radio. The R.A.P. (Retained Accessory
Power) function, where power is supplied to the radio
after the ignition is shut off until one of the front doors
are opened, is retained by the XSVI-9003.
INITIALIZE THE XSVI INTERFACE BEFORE TURNING
ON RADIO:
With all connections made and har-
nesses connected to the vehicle, turn ignition key
to the ON position for thirty seconds, then turn key
off.
Wiring the XSVI-9003:
Wiring up the XSVI-9003 is
like wiring up any other wire harness that would
attach to the aftermarket radios harness. The
Metra/EIA wire code can be found on the back of this
packa
ge tha
t will aid you in the wiring of your after
-
market radio.
(See Applications on back of page)
REV
.
06/12/07 INSTXSVI-9003
1-800-221-0932 www
.metraonline.com
METRA ELECTRONICS CORPORATION
© COPYRIGHT 2007
XSVI-9003
INSTALLATION INSTRUCTIONS
In the VW vehicles listed below there are no 12 volt
accessory wires currently in the factory harness mak-
ing the installer run an accessory wire to the fuse box
or underneath the steering column when installing an
aftermarket radio. The XSVI-9003 is designed to pro-
vide a 12 volt 10 amp switched accessory output
along with the rest of the wires needed to install an
aftermarket radio. The R.A.P. (Retained Accessory
Power) function, where power is supplied to the radio
after the ignition is shut off until one of the front doors
are opened, is retained by the XSVI-9003.
INITIALIZE THE XSVI INTERFACE BEFORE TURNING
ON RADIO:
With all connections made and har-
nesses connected to the vehicle, turn ignition key
to the ON position for thirty seconds, then turn key
off.
Wiring the XSVI-9003:
Wiring up the XSVI-9003 is
like wiring up any other wire harness that would
attach to the aftermarket radios harness. The
Metra/EIA wire code can be found on the back of this
packa
ge tha
t will aid you in the wiring of your after
-
market radio.
(See Applications on back of page)
REV
.
06/12/07 INSTXSVI-9003
1-800-221-0932 www
.metraonline.com
METRA ELECTRONICS CORPORATION
© COPYRIGHT 2007
XSVI-9003
INSTALLATION INSTRUCTIONS
In the VW vehicles listed below there are no 12 volt
accessory wires currently in the factory harness mak-
ing the installer run an accessory wire to the fuse box
or underneath the steering column when installing an
aftermarket radio. The XSVI-9003 is designed to pro-
vide a 12 volt 10 amp switched accessory output
along with the rest of the wires needed to install an
aftermarket radio. The R.A.P. (Retained Accessory
Power) function, where power is supplied to the radio
after the ignition is shut off until one of the front doors
are opened, is retained by the XSVI-9003.
INITIALIZE THE XSVI INTERFACE BEFORE TURNING
ON RADIO:
With all connections made and har-
nesses connected to the vehicle, turn ignition key
to the ON position for thirty seconds, then turn key
off.
Wiring the XSVI-9003:
Wiring up the XSVI-9003 is
like wiring up any other wire harness that would
attach to the aftermarket radios harness. The
Metra/EIA wire code can be found on the back of this
packa
ge tha
t will aid you in the wiring of your after
-
market radio.
(See Applications on back of page)
REV
.
06/12/07 INSTXSVI-9003
1-800-221-0932 www
.metraonline.com
METRA ELECTRONICS CORPORATION
© COPYRIGHT 2007
XSVI-9003
INSTALLATION INSTRUCTIONS
APPLICATIONS
VOLKSWAGEN
Golf (Double-Din models only) 2002-06
G
TI 2002-07
New Jetta 2005-07
Jetta 2005
J
etta (Double-Din models only) 2002-04
Passat (Double-Din models only) 2002-07
EOS 2007
R
abbit 2006-07
APPLICATIONS
V
OLKSW
A
GEN
Golf (Double-Din models only) 2002-06
GTI 2002-07
N
ew Jetta 2005-07
Jetta 2005
J
etta (Double-Din models only) 2002-04
P
assat (Double-Din models only) 2002-07
EOS 2007
R
abbit 2006-07
APPLICATIONS
VOLKSWAGEN
G
olf (Double-Din models only) 2002-06
GTI 2002-07
New Jetta 2005-07
J
etta 2005
Jetta (Double-Din models only) 2002-04
Passat (Double-Din models only) 2002-07
E
OS 2007
R
abbit 2006-07
APPLICATIONS
VOLKSWAGEN
G
olf (Double-Din models only) 2002-06
GTI 2002-07
New Jetta 2005-07
J
etta 2005
Jetta (Double-Din models only) 2002-04
Passat (Double-Din models only) 2002-07
E
OS 2007
R
abbit 2006-07
APPLICATIONS
VOLKSWAGEN
Golf (Double-Din models only) 2002-06
GTI 2002-07
New Jetta 2005-07
Jetta 2005
Jetta (Double-Din models only) 2002-04
Passat (Double-Din models only) 2002-07
EOS 2007
Rabbit 2006-07
APPLICATIONS
VOLKSWAGEN
Golf (Double-Din models only) 2002-06
GTI 2002-07
New Jetta 2005-07
Jetta 2005
Jetta (Double-Din models only) 2002-04
Passat (Double-Din models only) 2002-07
EOS 2007
Rabbit 2006-07
APPLICATIONS
VOLKSWAGEN
Golf (Double-Din models only) 2002-06
GTI 2002-07
New Jetta 2005-07
Jetta 2005
Jetta (Double-Din models only) 2002-04
Passat (Double-Din models only) 2002-07
EOS 2007
Rabbit 2006-07
APPLICATIONS
VOLKSWAGEN
Golf (Double-Din models only) 2002-06
GTI 2002-07
New Jetta 2005-07
Jetta 2005
Jetta (Double-Din models only) 2002-04
Passat (Double-Din models only) 2002-07
EOS 2007
Rabbit 2006-07
/