Saniflo 099 Operating instructions

CUBIC 2 VX

04.19

279

SANICUBIC 2 VX

®

IMPORTANT

DO NOT RETURN ANY MERCHANDISE TO THE VENDOR

NE PAS RETOURNER DE MARCHANDISE AU VENDEUR

For Customer Service, Returns or Technical Questions, please call Saniflo’s Technical Support toll-free at

800-571-8191 (USA) or 800-363-5874 (CDN).

Pour le service client, les retours ou toute question technique, merci d’appeller le service technique de Saniflo

au numéro suivant : 800-363-5874 (CDN).

This product must be installed in strict accordance with local plumbing codes.

Product should be installed by a licensed plumber.

Le produit doit être installé dans le respect des règlements sanitaires locaux.

Le produit doit être installé par un plombier qualié.

C

US

USA

CDN

1

2

4

3

5 6

✓

20” Max.

✓

×

* Possible connection

*

✓

×

1-½” or 4” Drain1-½” or 4” Drain

1-½” or 4” Drain

1-½”Drain

2-1/2” Vent

2” or 4” Discharge

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

1

2

E

x4

I

x4

J

x1

K

x2

L

x2

G

x1

M

x1

N

x1

H

x2

F

x8

D

x2

C

x1

B

x2

A

x2

Ø40/50mm

Ø100/110

100/120

122x130

Ø75mm

40x60

A

B

A

D

C

G

80x100

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

24” (610mm) min

2” Discharge

Ø60/110mm

71x76

D

4” Discharge

GLUE

PVC

Entire Homes

or Building

Structures

3

6

5

7

8

4

F

E

F

I

H

I

F

E

F

I

H

I

F

E

K

J

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

1- 1/2” Inlet

4”Inlet

2-1/2”Vent

12

9

11

L

I

H

I

L

F

E

L

M

N

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

1- 1/2” Inlet

4”Inlet

2-1/2”Vent

13 Ft (3.7m) Max

8 Ft (2.5m) Max

16 Ft (5m) Max

12” (30 cm) min

10

12

13

1

2

!

×

RESET

=

I

=

×

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

16 Ft (5m) Max

5

3

6

8

7

4

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

1

3

2

1

2

3

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

4

5

6

7

9

10

6

5

7

4

46

45

35

34

35

74 28 31

28

1743534

35

7

18

61

61B

61A

3

12

47B

47

68

67

76

36

3736

80

28

31

15

92

91

93

77

71

28

90

79

78

38

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

SANICUBIC 2 VX

EN 12050-1

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

Feet

Gal/min

Data specications

Type of current 1 phase

Voltage 220-240V

Frequency 60 Hz

Motor rating 1.5 HP

Current 12 A

Protection code Station: IP68, control box: IPX4

Shut o head 43 ft

Max. discharge height 36 ft (2’’) / 20 ft (4’’)

Max. ow rate 125 gpm (2") or 137 gpm (4")

Max. ow rate (both motors in operation) 145 gpm (2”) or 250 gpm (4”)

Max temperature 158°F

Solids handling diameter 2"

Tank volume 31.7 gallons

Useful volume 6.8 gallons

ON / OFF level activation 180 mm /100 mm

ON alarm activation 255 mm

Weight including accessories 223 Lbs

Discharge 2" or 4"

Inlet 1-1/2" & 4"

Ventilation 2-1/2"

0

5

10

15

20

25

30

35

40

45

10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

discharge Max 2"

discharge Max 4"

m1+m2m1

Discharge height

Flowrate

36"

29-5/8"

16"

28"

17-1/4"

7-1/2"

6-3/4"

5-5/8"

18"

8-1/8"

5"

4-5/8"

8-1/8"

2-1/2"

5"

5 1/8"

3 1/8"

1 3/4"

R5

3 3/4"

5 1/8"

3 1/8"

1 3/4"

R5

3 3/4"

9-1/2"

7-3/8"

4-3/8"

IMPORTANT

DO NOT RETURN ANY MERCHANDISE TO THE VENDOR

NE PAS RETOURNER DE MARCHANDISE AU VENDEUR

For Customer Service, Returns or Technical Questions, please call Saniflo’s Technical Support toll-free at

800-571-8191 (USA) or 800-363-5874 (CDN).

Pour le service client, les retours ou toute question technique, merci d’appeller le service technique de Saniflo

au numéro suivant : 800-363-5874 (CDN).

This product must be installed in strict accordance with local plumbing codes.

Product should be installed by a licensed plumber.

Le produit doit être installé dans le respect des règlements sanitaires locaux.

Le produit doit être installé par un plombier qualié.

For service or for further inquiries, please call or contact one of the following addresses:

Pour le service et d’autres demandes de renseignements, veuillez appeler à l’une des adresses indiquées ci-dessous :

United States Canada

SFA-SANIFLO INC. SFA-SANIFLO INC.

105 Newfield Avenue, Suite A 500 Jamieson Parkway, Unit 5

Edison, NJ 08837 Cambridge, ON N3C 0G5

Toll Free: 1-800-571-8191 Toll Free : 1-800-363-5874

Telephone: 1-732-225-6070 Telephone: 1-519-824-1134

Fax: 1-732-225-6072 Fax: 1-519-824-1143

E-mail:

[email protected]

E-mail: [email protected]

Web Site: www.saniflo.com Web Site: www.saniflo.ca

Sanicubic 2 VX

220-240 V / 60 Hz / 2 x 1.5 HP

Data specications

Type of current 1 phase

Voltage 220-240V

Frequency 60 Hz

Motor rating 1.5 HP

Current 12 A

Protection code Station: IP68, control box: IPX4

Shut o head 43 ft

Max. discharge height 36 ft (2’’) / 20 ft (4’’)

Max. ow rate 125 gpm (2") or 137 gpm (4")

Max. ow rate (both motors in operation) 145 gpm (2”) or 250 gpm (4”)

Max temperature 158°F

Solids handling diameter 2"

Tank volume 31.7 gallons

Useful volume 6.8 gallons

ON / OFF level activation 180 mm /100 mm

ON alarm activation 255 mm

Weight including accessories 223 Lbs

Discharge 2" or 4"

Inlet 1-1/2" & 4"

Ventilation 2-1/2"

CUBICVX

04.19

SANICUBIC

®

SANICUBIC

®

1 VX

SANICUBIC

®

2 VX

Operating / installation manual • Notice de service / montage

2

1

SAFETY

This device may be used by children who are at least

18 years old, by people with reduced physical, sensory

or mental capacities or those without knowledge or

experience, if they are properly supervised and if the

instructions relating to using the device completely safely

have been given to them and the associated risks have

been understood. Children must not play with the device.

Cleaning and maintenance undertaken by the user must

not be carried out by unsupervised children.

1.1 Identication of warnings

Symbol Meaning

DANGER

This term denes a high risk of danger,

which can lead to

death or serious injury, if not avoided.

WARNING

This term denes a hazard which could cause a risk to

the machine and its operation, if it is not taken into

account

Dangerous area

This symbol, in combination with a keyword, characte-

rizes hazards that could lead to death or injury.

Dangerous voltage

This symbol, in combination with a keyword, characte-

rizes dangers associated with the voltage and provides

information on voltage protection.

Property damage

This symbol, in combination with the keyword

WARNING, characterizes dangers to the machine and its

proper operation.

1.2 General points

This operating and installation manual contains important instructions to

follow for the tting, operation and maintenance of the SANICUBIC VX® pum-

ping stations. Following these instructions guarantees safe operation and

prevents injury and property damage.

Please follow the safety instructions in every section.

Before tting and commissioning the pumping station, the qualied installer/

user concerned must read and understand all these instructions.

1.3 Intended use

Only use the pumping station in the elds of application described in this

documentation.

• The pumping station must only be operated in technically perfect condi-

tions.

• Do not use a partially assembled pumping station.

• The pumping station must only pump the uids described in this documen-

tation.

• The pumping station must never operate without uid.

• Contact us for operating modes not described in this documentation.

• Never exceed the usage limits dened in the documentation.

• The safe use of the pumping station is only guaranteed if used as intended

(=> section 5.2).

1.4 Safety instructions for maintenance, inspection and installation

• Any alteration or modication of the pumping station will void the warranty.

• Only use original parts or parts recognized by the manufacturer. The use of

other parts may void the manufacturer’s liability for any resulting damage.

• The operator must ensure that all maintenance, inspection and installation

work is carried out by qualied plumber having previously studied this opera-

ting and installation manual.

• Before working on the pumping station, switch it o and unplug the pum-

ping station’s power plug.

• You must follow the procedure for shutting down the pumping station des-

cribed in this operating manual.

• Pumping stations discharging uids that may be harmful to health must

be decontaminated. Before restarting the pumping station, follow the

commissioning instructions. (c section 5.1, page 7)

• Keep unauthorized people (children, for example) away from the pumping

station.

• Never exceed the usage limits dened in the documentation.

• Follow all the safety precautions and instructions in this operating and

installation manual.

This operating manual must always be available on site so it can be ac-

cessed by qualied sta and the operator.

1.5 Risks and consequences of non-compliance with the operating

manual

Failure to comply with this operating and installation manual will result in

the loss of warranty rights and rights to damages.

US/CAN

2

TRANSPORT / TEMPORARY STORAGE / RETURNS / DISPOSAL

2.1 Receiving inspection

• When receiving goods, check the condition of the pumping station’s pac-

kaging.

• In case of damage, note the exact damage and immediately notify the

dealer in writing.

2.2 Transport

Dropping the pumping station

Risk of injury if the pumping station is dropped!

w Keep the pumping station horizontal when moving it.

w Observe the indicated weight.

w Never suspend the pumping station by the power cord.

w Use suitable means of transport.

✓ The pumping station has been inspected to make sure there is no

damage due to transport.

Choose suitable means of transport according to the weight table

Table 1: Weight of the pumping station

Model Gross Weight

(including packaging

and accessories) [lbs]

SANICUBIC® 1 VX 68 lbs

SANICUBIC® 2 VX 223 lbs

2.3 Temporary storage / Packaging

In the case of commissioning after an extended storage period, take the

following precautions to ensure storage of the pumping station:

WARNING

Wet, dirty or damaged openings and junction points. Leaks or

damage to the pumping station!

w

Clear the pumping station’s blocked openings at the time of instal-

lation.

2.4 Returns

• Properly drain the pumping station.

• Rinse and decontaminate the pumping station, especially if it has transported

harmful, explosive, hot or otherwise dangerous liquids.

2.5 Disposal

The device must not be disposed of as household waste and must be

disposed of at a recycling point for electrical equipment. The device’s

materials and components are reusable. The disposal of electrical and

electronic waste, recycling and recovery of any form of used appliances

contribute to the preservation of our environment.

3

DESCRIPTION

3.1 General description

This device is a compact pumping station. SANICUBIC® 1 VX is a pumping

station specially developed for individual use (detached house or small

commercial premises). SANICUBIC® 2 VX is a pumping station specially

developed for individual, commercial and small community use (small

buildings, shops, public places).

3.2 Scope of supply

Depending on the model, the following components are provided:

• Sump tank with 1 or 2 pumps and 3 level sensors

• Wired remote control box

• Wired alarm unit

• Check valves

• Mounting kit (screws, pegs)

• Connecting sleeves for inlet, discharge and ventilation piping

• Clamps for the connecting sleeves

3.3 Rating plate

Examples:

Pumping station

1

2

3

4

5

6

1 Name of the lifting station

2 Power supply

3 Frequency

4 Date of production

5 Identication number

6 Type of certication

Control box

1

2

3

4

7

6

5

1

Name of the pumping station

2 Name of the control box

3 Power supply

4 Phase type

5 Frequency

6 Protection index

7 Date of production

US/CAN

3.4 Design and operating mode

Table 2: SANICUBIC® 1 VX

1 Inlet Ø 1 1/2’’ or 4’’

2 Inlet Ø 1 1/2’’

3 Waste pipe Ø 2 or 4’’

4 Ventilation opening Ø 2 1/2’’

5 Level sensor (dip tube)

6 Tank

7 Access panel

8 Control opening

9 Built-in check valve

10 Engine-pump assembly

11 Vortex impeller

The pumping station is equipped with several horizontal and vertical inlet

openings for 1 1/2’’ or 4’’ outside diameter piping (1) and 1 1/2’’ outside

diameter piping (2). The engine-pump assembly (10) carries the pumped

uid in the vertical discharge piping with an inside diameter of 2’’ or 4’’.

The ventilation duct (4) allows the tank to always remain at atmospheric

pressure.

Operating mode:

Euent enters the pumping station through the horizontal and vertical inlet

openings (1) (2). They accumulate in a gas-tight, smell-proof and watertight

plastic tank (6). Controlled by a level sensor (5) and a control box, euents

are carried away by vortex impeller (11) and automatically pumped, when

they reach a certain level in the tank, by one or two pumps, depending on

the model, (10) above the back-ow level to ow into the discharge line.

- SANICUBIC® 1 VX contains one pump with a vortex action.

- SANICUBIC® 2 VX contains two independant pumps, each with a clearance

of 50 mm. Both pumps operate each in turn, alternately. In case of

abnormal operation, both engines run simultaneously (or if one vortex

pump fails, the other takes over)

.

Level sensor / Dip tube:

• 2 Long dip tubes

During normal operation, as soon as the euents reach the long tube’s

actuation level in the tank, the pumping system switches on.

• Short dip tube

During abnormal operation, if the euents reach the highest level in the

tank (short tube), an audible and visual alarm system is activated and the

pumping system switches on (if it is not faulty).

4

US/CAN

3.5 Technical data

Submersible pumping stations for blackwater

SANICUBIC® 1 VX

Type of current Single-phase

Power/Electrical information 220-240V/ 60 Hz / 12A/ 1,5 HP

Motor - Pump Oil bath cooled

Thermal overload protection

Class F insulation

Type of pump Vortex Impeller

Cable station – control box

13 feet - H07RN-F-4 G 1.5

Control box cable – socket 8 feet-14/3 AWG SJOOW

Protection Station: IP68

Control box: IPX4

Max. recommended height 36 Ft (2’’) / 20 Ft (4’’)

Shut o head 43 ft

Max. ow 125 gpm (2’’) / 137 gpm (4’’)

Max. temperature of incoming wastewater 158 °F (Max. 5 min.)

Tank volume 15.9 gallons

Usefull volume 5.5 gallons

Height of low inlets (from the ground) 6 1/8 ‘’

Gross Weight [lbs] 68 lbs

Waste pipe 2’’ or 4’’

Inlet Ø 1 1/2’’ or 4’’

Ventilation 2 1/2’’

Flow curve

Discharge height

Flowrate

Feet

Gal/min

0

5

10

15

20

25

30

35

40

45

10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

discharge Max 2"

discharge Max 4"

SANICUBIC® 2 VX

Type of current Single-phase

Power/Electrical information 220-240V/ 60Hz/ 2 x12A / 2 x1,5 HP

Motor - Pump Oil bath cooled

Thermal overload

protection

Class F insulation

Type of pump Vortex Impeller

Cable station – control box 13 feet - H07RN-F-4 G 1.5

Control box cable – socket 8 feet-12/3 AWG SJOOW

Protection Station: IP68

Control box: IPX4

Max. recommended height 36 Ft (2’’) / 20 Ft (4’’)

Shut o head 43 ft

Max. ow

*Both motors in operation 145 gpm (2’’) or 250 gpm (4’’)

Max. temperature of incoming wastewater 158 °F (Max. 5 min.)

Tank volume 31.7 gallons

Usefull volume 6.8 gallons

Height of low inlets (from the ground) 7 1/2’’

Gross Weight [lbs]

(including packaging and accessories) : 223 lbs

Waste pipe 2’’ or 4’’

Inlet Ø 1 1/2’’ or 4’’

Ventilation 2 1/2’’

Volume units of measurement : Gal (US)/min

Flow curve

3.6 Control box

Submersion of the control device

Risk of death by electric shock

w

Only use the control device in rooms safe from oods

SANICUBIC® VX remote control box

• Pump control and monitoring cabinet integrated into a compact plastic housing

• For 1 or 2 pumps

• Option of forced mode

3.6.1 Electrical characteristics

Table 3: Electrical characteristics of the control box

Parameter Value

Nominal power supply 220-240V

Network frequency 60 Hz

Protection index IPX4

3.6.2 Technical characteristics of the detection device

Analog level sensor:

• Input voltage 0 - 5 V

Process outputs:

• One potential-free signalling output (250 V, 16 A) NO Contact

• One signalling output for the wired alarm unit that comes with the device

(except SANICUBIC® 2 VX): 5V, 50mA

3.6.3 Dimensions of the remote control box

3.7 Alarm unit

3.7.1 Technical characteristics of the alarm device

SANICUBIC® VX alarm unit:

Wired alarm unit

16’’ cable

Audio and visual information

Protection index: IP20

3.7.2 Dimensions of the remote alarm unit

3.7.3 Option of connection to an external alarm

Option of externalizing the alarm signal (depending on the model). Dry

contact (no voltage) NO (normally open) operated by a max. 250V/16A relay.

The terminals can be connected to a powered system.

This contact closes as soon as the station is in alarm mode (except in the case

of area alarm) and remains closed as long as the alarm sounds.

5

US/CAN

External alarm

Max. 250 V / 16A

Dry contact

NO

3.8 Sump tank

The sump tank is designed for pressure-free operation. Wastewater is collec-

ted there at atmospheric pressure before being discharged to the sewer. The

ventilation duct allows the tank to always remain at atmospheric pressure

3.9 Pumped uids

Pumping unauthorized uids

Dangerous for people and the environment!

w

Only discharge authorized pumped uids in the public sewerage

network

Authorized pumped uids:

The following liquids are allowed in discharge systems:

Water contaminated by domestic use, human excrement.

Unauthorized pumped uids:

The following liquids and substances are banned:

• Solid materials, bres, tar, sand, cement, ash, coarse paper, hand towels,

wipes, cardboard, rubble, rubbish, slaughterhouse waste, oils, greases,

etc.

• Wastewater containing harmful substances (for example, untreated

greasy waste from restaurants). Pumping these liquids and substances

requires the tting of a compliant grease trap.

• Rain water.

3.10 Noise level

The noise level depends on the tting conditions and operating point. This

sound pressure level Lp is less than 70 dB.

4

INSTALLATION / FITTING

4.1 Installing the pumping station

• The characteristics shown on the rating plate have been compared with

those on the order and installation (supply voltage, frequency).

• The installation room must be protected against frost.

• The installation room is adequately lit.

• The work has been prepared in accordance with the dimensions shown in

the example installation.

• The plant room where the SANICUBIC® VX will be installed must be large

enough to allow a minimum 24 inches in clearance around and above the

device to facilitate maintenance.

• The alarm signal is always visible to the user (if necessary, use an external

alarm contact switch).

• Isolating valves (not provided) must be tted on the euent inlet as well as

on the discharge line, as close as possible to the pumping station.

• The discharge line must be designed to prevent any back-ow of sewage.

By tting a non-return loop, located above the back-ow level, back-ow is

avoided.

Comment: In the absence of local information to the contrary, the maximum

back ow level corresponds to street level - roadway, pavements etc. Extend

this line after the non-return loop through a larger diameter pipe.

• The installation of an auxiliary pump for possible drainage of the plant room

(for oods) is recommended.

• The pumping station must be ventilated above the roof.

• The pumped uid is appropriate and authorized by this documentation.

(section 3.9, page 5)

• In case of discharge of greasy euents, the use of a degreasing tank is

essential.

Wastewater other than those mentioned above, for example, of artisanal or

industrial origin, must not be discharged into the pipes without prior treat-

ment.

4.2 Electrical connection

Electrical connection work performed by an unqualied indivi-

dual. Risk of death by electric shock!

w The electrical connection must be performed by a qualied

and licensed electrician.

w The electrical installation must meet the current standards in

the country

Wrong supply voltage. Damage to the pumping station!

w The supply voltage must not dier by more than 6% of the

rated voltage specied on the rating plate.

The power supply must be class 1. The device must be connected to an

earthed junction box. The electrical power supply must be protected with a

high sensitivity circuit breaker set to 10 Milli Amps for SANICUBIC® 1 VX and

20 Milli Amps for SANICUBIC® 2 VX. This connection must be used exclusively

for the SANICUBIC® VX power supply. If the cord of this device is damaged,

it must be replaced by the manufacturer or its after-sales service in order to

avoid any danger to users.

4.3 Fitting the pumping station

Fit the pumping station on the bare ground and level it with a bubble level.

To avoid any risk of the pumping station oating, attach it to the ground

using the mounting kit provided.

NOTE

Fitting the pumping station on anti-vibration mounts ensures

sucient insulation against structure-borne sound with respect

to the pumping station. Do not t the pumping station in direct

contact with the walls to avoid transmission of the pumping

station’s vibrations

4.4 Pipe connections

4.4.1 Inlet pipes

w The pumping station must not be used as a control point

for piping.

w Prop up the pipes upstream from the pumping station.

Make connections without constraints.

w Use suitable means to compensate for thermal expansion

of the piping.

NOTE

It is recommended that you mount check valves and isolating

valves on the inlet pipes. These must be mounted so that they do

not hinder disassembly of the pumping station.

✓ The piping is supported.

1. Choose the connection openings to use.

2. Cut the tip of the corresponding inlet with a saw

3. Do not install a one-way valve such as mechanical vents

NOTE

All piping connections must prevent the propagation of noise

and be exible.

6

US/CAN

4.4.2 Discharge piping

Improper tting of the discharge pipe. Leaks and ooding of

the installation room!

w Run the discharge line above the back-ow level before

connecting to the sewer.

w The pumping station must not be used as a control point

for piping.

wDo not connect other drain pipes to the discharge pipe.

wFit isolation valves to inlets and discharge pipework.

NOTE

To prevent the risk of back-ow of water from the sewer,

install the discharge pipe in a «loop» so that its base, at

the highest point, is located above the back-ow level.

Fit a shuto valve behind the check valve.

The check valves are equipped with a lever for emptying

the discharge pipe into the tank.

4.4.3 Ventilation pipe

Insucient ventilation. Risk that the pumping station will

not work!

w Ventilation must remain free

w Do not block the vent outlet

w

Do not install one-way vent systems.

It must be equipped with a vent above the roof. The pumping station must

always be ventilated so that the tank is always at atmospheric pressure.

The ventilation must be completely free and air must ow in both

directions (no studor, mechanical or one-way vents).

The vent pipe must not be connected to the vent pipe on the inlet side of

a grease trap.

Connect the 2 1/2’’ vent pipe (depending on the model) vertically to the

vent opening with the exible couplings. The connection must be smell-

proof.

5

COMMISSIONING / DECOMMISSIONING

5.1 Commissioning

5.1.1 Prerequisites for commissioning

Before commissioning the pumping station, make sure that the electrical

connection for the pumping station and all protective devices has been

correctly performed.

5.2 Application limit

w Pressure and temperature limits exceeded. Leakage of hot

or toxic uid!

w Observe the operating specications in the documentation.

w Avoid running the pump with the valve closed.

wDry running, without pumped uid, must be avoided.

When in use, observe the following parameters and values:

Parameter Value

Max. allowed temperature 104 °F

of the uid up to 158 °F when pumped

5 minutes max.

Max. room temperature 122 °F

5.3 Starting frequency

To prevent engine overheating and excessive stress on the engine, seals

and bearings, limit the number of starts to 60 per hour.

5.4 Commissioning with the control box

w The control box cover is not properly closed. Risk of death!

w Properly close the control box cover.

w Then reconnect the power plug.

Operations required for commissioning

1. Perform a functional and sealing test of the pumping station: Once the

hydraulic and electrical connections are made, check the connections

for leaks by running water successively through each inlet used. Ensure

the device is operating properly and there are no leaks by performing a

water test and observing several start cycles.

2. Check the various points on the checklist (c section 7.6, page 10)

3. Warning: Do not run the motor in forced mode (by pressing the key on

the keypad) before putting the pump in water. Dry running damages

the vortex system.

5.5 Decommissioning

1. Close the valves on the inlet and discharge pipes.

2. Drain the tank by pressing the forced mode button on the pump.

3. Switch o the electrical power supply and disconnect the installation.

w The current is not cut. Risk of death!

w Unplug the plug or disconnect the electrical conductors

and take the steps required to avoid inadvertent operation.

4. Inspect the hydraulic parts and vortex impeller (depending on the

model). Clean them if necessary.

5. Clean the tank.

w Pumped uids and secondary consumable materials that are

harmful to health. Dangerous for people and the environment!

w Pumping stations used to discharge uids that may be harmful

to health must be decontaminated.

If necessary, wear a mask and protective clothing.

w Observe current legal provisions for the discharge of uids

harmful to health.

6

OPERATION

6.1 SANICUBIC® VX Control box

NOTE

This paragraph describes the operation of a control box for

two pumps. The control box is operated in a similar manner

for one pump.

Table 4: SANICUBIC® VX remote control box

1 Yellow mains supply LED

2 Red alarm LED

3 Forced mode Engine 1

4 Forced mode Engine 2

LED lamps

The LED lamps provide information on the operating state of the control

box:

The detection system must be vented. Connect the vent hose to the

station’s control box.

7

US/CAN

Figure 2: Ventilation of the SANICUBIC® VX control box

6.1.1. Operation of the SANICUBIC® 1 VX control remote box (IP68)

1/ General alarms:

Level alarm:

If the water level inside the device is abnormally high, the alarm LED lights

up red + engine starts up. Furthermore, if this LED ashes red, it indicates a

detection problem for the normal water level (Long dip tube).

Time alarm:

If the motor runs continuously for more than 1 minute, the red alarm LED

lights up.

2/ Alarm reset: The button on the keypad will only allow you to turn o the

red LED (it will turn green) if the problem that triggered the alarm has been

resolved. It also allows you to stop the ringing of the remote alarm control.

Mains alarm:

- If the LED is o, there is no power supply.

- When the device is powered on again, the LED ashes green, indicating

that the mains voltage has temporarily disappeared.

6.1.2 Operation of the SANICUBIC® 2 VX

OPERATION OF THE ALARM

1/ General alarms:

Level alarm:

If the water level inside the device is abnormally high: the siren is triggered

+ the red alarm LED lights up + both motors start-up. If this LED ashes red,

it indicates a detection problem for the normal water level (Long dip tube).

Time alarm:

If one of the two motors runs for more than 1 minute: the siren is triggered

+ the red alarm LED lights up + the other engine starts-up.

Mains alarm:

In case of power failure (or when unplugging the device): the siren is trigge-

red + the red alarm LED lights up + the yellow mains LED blinks.

2/ General alarm reset:

If the problem that triggered one of the alarms above disappears, the siren

stops, but the red alarm LED remains lit as a reminder of the fact that the

system encountered a problem. Either of the two keypad keys will stop the

siren in all cases, but it will only turn o the red LED if the problem that

triggered the alarm has been resolved. Alarms from the remote box will also

remain active until the problem has been solved. This prevents the system

from being «abandoned» by default.

6.2 SANICUBIC® VX alarm unit

To wall mount the unit, use the following gure as a guide:

6.2.1 Operation of the SANICUBIC® 1 VX / SANICUBIC® 2 VX wired

alarm unit

The SANICUBIC® VX alarm unit does not require a separate power supply.

The power is supplied through the SANICUBIC® VX. In case of power failure,

the alarm unit’s battery takes over.

Connection of the alarm unit to the device:

Connect the alarm cable directly to the unit.

1/ The red general alarm LED reproduces

the operation of the red LED on the base

card. The alarm unit sounds in the event

of an alarm as long as the fault is present.

To stop the alarm, press the reset (*)

button on the device’s keypad or the

button under the alarm unit.

2/ The yellow «mains» LED indicates the

power status of the alarm unit

-Steady light = live SANICUBIC® VX connected

to the mains supply

-Flashing = power failure on the SANICUBIC® VX

1

2

Reset (*) :

Table 5: SANICUBIC® 1 VX / SANICUBIC® 2 VX alarm unit

1 Red general alarm LED

2 Yellow mains alarm LED (power supply indicator)

6.3 Messages and faults

Table 7: Messages and faults:

Alarm on the device SANICUBIC® 1 VX : Green LED: station live

Alarm on the device SANICUBIC® 2 VX : Yellow LED: station live

ANOMALY DETECTED

Flashing red alarm LED

Steady red alarm LED

LED off

CAUSES PROBLEMS

• Water level detection

system faulty

• Clogged vent pipe

• Clogged drain line

• Blocked or out of order

pump

• Discharge too high or

excessive inflow

• Mains failure

• Faulty electronic board

SOLUTIONS

• Consult SANIFLO

after-sales service

• Check that air flows freely

in both directions in the

vent pipe

• Go over the installation

again

• Consult SANIFLO

after-sales service

• Check the electrical system

• Consult SANIFLO

after-sales service

8

US/CAN

NOTE: If both switches are

lowered (off position), abnor-

mal situation, the card will be

in alarm mode when power is

restored

7.5.1 General information

Inspect the tank, check for possible deposits, the presence of grease and

foreign bodies. Thoroughly clean the tank and remove foreign bodies.

7.5.2 Disassembling the motor

1. Unscrew the motor hatch from the tank cover (10 screws).

2. Use the handle to gently lift the motor. If the defective motor is to be

returned to the manufacturer, the pumping station can provide a minimum

service with one single motor.

3. Unscrew the screws of the faulty motor from the hatch.

4. Put the hatch back in position.

7.5.3 Disassembling and inspection of the compression chambers and

level sensors:

1. Unscrew (1 screw), unlock and lift the pressure switch from the cover.

2. Check that the funnels are not obstructed (grease, faecal matter etc.).

Clogged compression chambers indicate that the device has not been

properly maintained. It is recommended to clean the device at least every

6 months.

3. If necessary unclog the compression chambers.

7.5.4 Reassembly of the level sensors

Warning: Do not grease the level sensors’ O-rings before reassembly.

1. Fully insert the level sensor in the compression chamber.

2. Screw the level sensor onto the cover.

7.5.5 Reassembly

During reassembly, observe the following points:

To reassemble the pump, observe the rules applicable to engineering

goods. Do not over-tighten the screws on plastic parts (risk of breaking the

plastic) and clamps.

Clean all disassembled parts and check their wear.

Replace damaged or worn parts with original spare parts.

Ensure that the sealing surfaces are clean and the O-rings are properly

installed.

7.5.6 Tightening torque

The tightening torque for screws and clamps is 2 ± 0.1 N.m

7

MAINTENANCE

7.1 General information / Safety instructions

Work performed on the pumping station by unqualied sta. Risk

of injury!

w Repairs and maintenance must be performed by specially

trained sta

w Observe the safety and basic instructions.

Pumped uids and secondary consumable materials that are har-

mful to health. Dangerous for people and the environment!

w Pumping stations used to discharge uids that may be harmful

to health must be decontaminated.

If necessary, wear a mask and protective clothing.

w Observe current legal provisions for the discharge of uids

harmful to health.

7.2 Maintenance and inspection operations

Work on the pumping station without adequate preparation.

Risk of injury!

w Properly stop the pumping station and secure it against inad-

vertent operation.

w Close the inlet and discharge valves.

w Drain the pumping station.

w Close any auxiliary connections.

w Allow the pumping station to cool to room temperature.

Pumping stations must be maintained and repaired to ensure the proper

disposal of wastewater and to detect and eliminate malfunctions at an early

stage.

The proper functioning of pumping stations must be checked by the user

once a month by observing at least two operating cycles.

The inside of the tank should be checked from time to time and deposits,

especially around the level sensor, should be removed, if necessary

Maintenance of the pumping station must be performed by qualied sta.

The following intervals should not be exceeded:

• 3 months for pumping stations for industrial use

• 6 months for pumping stations for small communities

• 1 year for domestic pumping stations

7.3 Maintenance contract

As with any technical, high-performance equipment, SANICUBIC® VX

pumping stations must be maintained to ensure a sustainable level of

performance. We recommend you take out a maintenance contract with a

qualied company to carry out regular inspection and maintenance work. For

more information, please contact us.

7.4 Emergency service with a single pump

NOTE

If emergency service must be ensured during maintenance and

inspection work, perform the following steps.

1. Close the valves on the inlet and discharge sides.

Warning: The incoming feed for inlets must be minimised while performing

maintenance

2. Turn o the power supply.

7.5 Checking the hydraulics of each motor

• Make sure its blade and plate are not blocked or damaged.

• Make sure the turbine rotates freely

• Make sure the hydraulic parts are clean. Clean them if necessary.

In case an motor is not working properly, it is possible to “disable” the use of

this motor by switching the corresponding “switch” on the main card to in-

dicate the absence of the corresponding motor. The card will only work with

the valid motor - SW1: switch 1 and 2 for motor 1 (left) and 2 (right).

9

US/CAN

8. Incidents: causes and solutions

A B C D E F G H

- ✘ - - - ✘ - -

✘ - - - - ✘ - -

- ✘ - ✘ ✘ ✘ - -

- - ✘ - ✘ ✘ - -

✘ - - - - ✘ ✘ -

✘ - - - - - - -

- ✘ - - - ✘ - -

- - - - - ✘ - ✘

- - - - ✘ - - -

✘ - - - ✘ ✘ ✘ -

- - - ✘ - - -

- ✘ - ✘ - - - -

Possible cause

Pump flows against excessive

pressure.

The discharge valve is not fully open.

The pumping station is not ventilated.

Inlet pipes or wheel clogged.

Presence of deposits / fibres in the

wheel.

The rotor does not turn freely.

The engine is off.

Trigger of the thermal protection due

to excessive temperature.

Deposits in the sump tank.

The check valve is leaky.

Vibrations in the installation.

Faulty, clogged, pulled out or impro-

perly inserted level sensor.

Faulty capacitor

In the case of three-stage installation:

2 phases may be inverted.

To check, visually look at the motor

rotation direction by dismantling the

motor.

Solutions

The size of the pumping station

is insufficient for these operating

conditions.

Open the valve to the maximum.

Check the pumping station’s vent

pipes

Remove deposits in the pump and/

or piping.

Check if the wheel turns freely without

blocking. If necessary, clean the pump.

Check the electrical installation (and

fuses).

The engine automatically restarts

after cooling.

Clean the sump tank. In case of grease

deposits, make sure there is a grease

trap.

Clean the check valve.

Check the flexible pipe connections.

Check the level sensor. Clean or replace

it, if necessary.

Replace the capacitor

With the connection, inverse 2 power

cable phases (5 wires).

7.6 Checklist for commissioning / inspection  and maintenance 

Operations

Read the operating manual.

Check the power supply.

Compare the values with those of the rating plate.

Check the connection of the power supply to the earth.

heck the connection of the power supply to a 30 mA GFCI breaker.

Check the proper operation of the motors by pressing the forced mode buttons.

If abnormal, make sure the pump is not clogged, check the resistance values of the

engine coils.

Check the sump tank.

Clean the tank in case of deposits.

In case of significant grease deposits in the tank from greasy wastewater

from artisanal or industrial businesses, inform the customer that they must install

a grease trap upstream from the pumping station.

Check the level sensors. Dismantle the pressure switches and make sure that the

dip tubes are not clogged. Clean them if necessary.

Check the control mechanism.

Dismantle the level sensor. Check if it is blocked or encrusted.

Clean them, if necessary.

Perform a functional test over several cycles.

Check the correct installation and state of wear of the flexible couplings.

Check the proper operation and effectiveness of the alarm device.

Check the proper operation and seal of the stop valves and check valves.

If applicable, identify the necessary spare parts.

Advise and/or train operating staff.

Required for

➀ ➁

➀

➁

➀ ➁

➀

➁

➀ ➁

➁

➀ ➁

NOTE

Before working inside the pump during the warranty period, you

must consult the manufacturer. Our after-sales service is available

to you. Failure to comply leads to the loss of rights to damages.

Inappropriate work aiming to eliminate malfunctions. Risk of injury!

w For all work intended to eliminate malfunctions, follow this

operating manual’s instructions and / or the manufacturer’s

documentation for the relevant accessories.

NOTE

After every ood, the pumping station should be inspected.

NOTE

After an incident, subject the pumping station to functional test

and visual inspection.

For any problem not described in the table below, contact Sanio after-sales

service.

Problems encountered:

A The pump does not ow

B Insucient ow

C Excessive current / power consumption

D Insucient manometric delivery head

E Irregular and noisy operation of the pump

F Frequent faults reported by the pumping station

G Overow of the pumping station

H Untimely start

Before working on pressurised components, reduce the pressure inside the

pump! Disconnect the pump from the electrical power supply.

Page is loading ...

Saniflo 099 Operating instructions

Saniflo 099 Operating instructions

in other languages

Related papers

Other documents