1) Place each end of frame up against each side of canopy of
fixture. Align hole on each end of frame with hole in each
side of canopy. Thread screw into each hole in frame and
into sides of canopy. Tighten screws to secure frame to
canopy
2) Place one decorative wood piece up against frame of fixture
with hole in wood piece against frame of fixture. From inside
frame of fixture, thread screw into hole in frame and into
hole in wood piece. Carefully tighten screw to secure wood
piece to frame. Repeat step for remaining decorative wood
pieces.
3) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
4) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
5) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
6) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raise dimples. Wrap ground wire from outlet
box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
7) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
8) Push fixture to wall, carefully passing mounting screws
through holes.
9) Screw threaded balls onto mounting screws. Tighten
threaded balls to secure fixture to wall.
10) Lower shade down through top of fixture. Slip each hook on
top of shade into each hole in top canopy.
Date Issued: 12/4/15 IS-43756-US
MOUNTING STRAP
PLANCHA PARA MONTAR
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
THREADED BALL
BOLA ROSCADO
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CANOPY
ESCUDETE
FRAME
ARMAZÓN
DECORATIVE WOOD PIECE
PIEZA DE MADERA DECORATIVA
SCREW
TORNILLO
SCREW
TORNILLO
SHADE
PANTALLA
FIXTURE
ARTEFACTO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
Page is loading ...
6) Connecter les fils (connecteurs non fournis). Se reporter au
tableau ci-dessous pour faire les connexions.
7) Plaquez l’applique contre le mur, en passant soigneusement
les vis de montage dans les trous.
8) Visser les boules filetées sur les vis de montage. Serrer les
boules filetées pour fixer le luminaire au mur.
9) Abaisser le cache par-dessus du luminaire. Glisser chaque
crochet sur le dessus du couvercle dans chaque trou situé
au-dessus du couvercle.
1) Place each end of frame up against each side of canopy of
fixture. Align hole on each end of frame with hole in each
side of canopy. Thread screw into each hole in frame and
into sides of canopy. Tighten screws to secure frame to
canopy
2) Place one decorative wood piece up against frame of fixture
with hole in wood piece against frame of fixture. From inside
frame of fixture, thread screw into hole in frame and into
hole in wood piece. Carefully tighten screw to secure wood
piece to frame. Repeat step for remaining decorative wood
pieces.
3) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
4) Find the appropriate threaded holes on mounting
strap. Assemble mounting screws into threaded holes.
5) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
6) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
7) Push fixture to wall, carefully passing mounting screws
through holes.
8) Screw threaded balls onto mounting screws. Tighten
threaded balls to secure fixture to wall.
9) Lower shade down through top of fixture.
1) Placer chaque extrémité du cadre contre chaque côté du
couvercle du luminaire. Aligner le trou de chaque extrémité
du cadre au trou de chaque côté du couvercle. Serrer une
vis dans chaque trou du cadre et dans les côtés du cache.
Serrer les vis pour fixer le cadre au couvercle.
2) Placer un morceau de bois décoratif contre le cadre du
luminaire avec un trou dans le morceau de bois contre le
cadre du luminaire. De l’intérieur du cadre du luminaire,
serrer une vis dans le trou dans le cadre et dans le trou de la
pièce de bois. Serrer soigneusement une vis pour fixer la
pièce de bois sur le cadre. Répéter l’étape pour les autres
pièces de bois décoratifs.
3) COUPER LE COURANT.
IMPORTANT: TOUJOURS couper l’électricité avant de
commencer le travail.
a) Localiser le coffret à fusibles ou le disjoncteur du
domicile. Mettre l’interrupteur principal en position
d’Arrêt.
b) Dévisser le ou les fusibles (ou mettre le disjoncteur sur
Arrêt) qui contrôlent l’alimentation vers le luminaire ou la
pièce dans laquelle le travail est effectué.
c) Mettre l’interrupteur mural en position d’Arrêt. Si le luminaire
à remplacer est doté d’un interrupteur ou d’une chaîne
connectée à l‘interrupteur, placer ces éléments en
position d’Arrêt.
4) Trouver les trous filetés appropriés sur la barrette de montage.
Vissez les vis de montage dans les trous filetés.
5) Visser la barrette de montage à la boite de jonction. (Vis
non fournies). La barrette de montage peut etre ajustée pour
convenir à la position de l’applique.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 12/4/15 IS-43756-CB
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
MOUNTING STRAP
COLLLIER DE FIXATION
Connecter le fil noir ou
rouge de la boite
Connecter le fil blanc de la boîte
A Noir A Blanc
*Au cordon parallèle (rond et lisse)
*Au cordon parallele (à angles droits el strié)
Au bransparent, doré, marron, ou
noir sans fil distinctif
Au transparent, doré, marron, ou
noir avec un til distinctif
Fil isolé (sauf fil vert) avec
conducteur en cuivre
Fil isolé (sauf fil vert) avec
conducteur en argent
*Remarque: Avec emploi d’un fil paralléle
(SPT I et SPT II). Le fil neutre est á angles
droits ou strié et l’autre fil doit étre rond ou
lisse (Voir le schéma).
Fil Neutre
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
THREADED BALL
BOLA ROSCADO
CANOPY
CACHE
FRAME
MARCO
SCREW
VIS
SCREW
VIS
SHADE
ABAT-JOUR
FIXTURE
LUMINAIRE
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 9707BK User manual
-
Kichler Lighting 49119AVI User manual
-
Kichler Lighting 9035BKT User manual
-
Kichler Lighting 49120AVI User manual
-
Kichler Lighting 45195AVI User manual
-
Kichler Lighting 49123AVI User manual
-
Kichler Lighting 43755AUB User manual
-
Kichler Lighting 43716PN User manual
-
Kichler Lighting 49926BKT User manual
-
Kichler Lighting 49925OZ User manual
