Kichler Lighting 86000MBK User manual

Brand: Kichler Lighting

Model: 86000MBK

Type: User manual

Kichler Lighting 86000MBK is a LED fixture that can be used to light up a bathroom. It has a touch dimming switch on the bottom of the mirror that allows you to adjust the light output. Do not connect ground wire to black or white power supply wires. The fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.

IS-86000-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

1) Use provided paper template[A] to locate the desired

mounng locaon for the mirror and to mark the locaons

required for the wall anchors.

2) Use a 15/64 inch drill bit to drill pilot holes at the locaons

marked in step 1 and insert wall anchors[C].

3) Screw all but 1/8 inch length of each wood screw[D] into the

wall anchors.

4) Grounding instrucons: (See Illus. a or b).

a) On xtures where mounng strap is provided with a hole

and two raised dimples, wrap ground wire from outlet

box around green ground screw, and thread into hole.

b) On xtures where a cupped washer is provided, aach

ground wire from outlet box under cupped washer and

green ground screw, then thread into mounng strap.

If xture is provided with ground wire, connect xture ground

wire to outlet box ground wire with wire connector aer

following the above steps. Never connect ground wire to black

or white power supply wires.

5) Make wire connecons. Reference chart below for correct

connecons and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply

Wire to:

Black White

*Parallel cord (round &

smooth)

*Parallel cord (square &

ridged)

Clear, Brown, Gold or

Black without Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other

than green) with copper

conductor

Insulated wire (other

than green) with silver

conductor

*Note: When parallel wire (SPT

1 & SPT 2) are used. The neutral

wire is square shaped or ridged

and the other wire will be round

in shape or smooth (See illus.)

Neutral Wire

6) Hang mirror[B] by the keyhole slots[H] in the back of the

mirror. NOTE: the mirror should be oriented so that the

narrow poron of the keyhole faces up.

7) Extend the decorave strap[I] up and mark the hole locaon

for threaded tube[F].

8) Use a 15/64 inch drill bit to drill pilot hole and insert the wall

anchor[C].

9) Take the long screw[E] and place into the threaded tube and

secure to the installed wall anchor.

10) Slide the decorave strap over the installed threaded tube

and take the decorave cap[G] and thread into the installed

threaded tube.

11) To change the light output of your mirror, tap the switch on

the boom of the mirror or gently press the switch. The switch

is a touch dimming switch.

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Fixture Diagram

Parts List

[A] Paper

Template

[B] Mirror

[C] Wall Anchors

[D] Wood Screw

[E] Long Screw

[F] Threaded

Tube

[G] Decorative

Cap

[H] Keyhole Slots

[I] Decorative

Strap

Cauons

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main

fusebox before starng and during the installaon.

WARNING:

This xture is intended for installaon in accordance with the

Naonal Electrical Code (NEC) and all local code specicaons.

If you are not familiar with code requirements, installaon by a

cered electrician is recommended.

DIMMING:

This LED xture is not compable with wall dimmer switches. Light

output can only be adjusted by using the touch dimming switch on

the boom of the mirror.

CLEANING:

Always be certain that electric current is turned o before cleaning.

• Only a so damp cloth should be used. Harsh cleaning

products may damage the nish.

Installaon Instrucons

This device complies with part 15 of the FCC Rules. Operaon is subject to the

following two condions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that

may cause undesired operaon.

Note: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protecon against harmful interference in a residenal

installaon. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instrucons, may cause

harmful interference to radio communicaons. However, there is no guarantee that

interference will not occur in a parcular installaon. If this equipment does cause

harmful interference to radio or television recepon, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separaon between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Informaon:

For warranty informaon please visit: kichler.com/warranty

22.0 [558.0]

TEMPLATE

Page is loading ...

IS-86000-CB