Mettler Toledo HX204 Halogen Moisture Analyzer Operating instructions

Ex

c

e

llence

Plus

Moisture Analyzer

Excellence Plus HX204

Reference Manual

30019565F1/30/2020 12:46 PM- Schema ST4 PDF engine -Layout by Victor Mahler

Table of Contents

1 Introduction 5

2 Safety Information 6

2.1 Definition of signal warnings and symbols...................................................................... 6

2.2 Product specific safety information................................................................................. 6

3 Design and Function 9

3.1 Overview..................................................................................................................... 9

3.1.1 Overview drying unit...................................................................................... 9

3.1.2 Overview terminal ......................................................................................... 10

3.1.3 Overview type plates...................................................................................... 10

3.2 Compliance Information................................................................................................ 11

3.3 Function description..................................................................................................... 11

4 Installation and Putting into Operation 13

4.1 Selecting the location ................................................................................................... 13

4.2 Unpacking .................................................................................................................. 13

4.3 Scope of delivery ......................................................................................................... 13

4.4 Connecting the instrument............................................................................................. 14

4.5 Opening and closing sample chamber ........................................................................... 14

4.6 Setup wizard ............................................................................................................... 15

4.7 Setting up the instrument .............................................................................................. 15

4.8 Leveling the instrument................................................................................................. 16

4.9 Anti-theft device ........................................................................................................... 18

4.10 Setting reading angle of terminal.................................................................................... 18

4.11 Setting date and time.................................................................................................... 18

4.12 Adjusting after setup..................................................................................................... 18

4.13 Transporting, packaging and storing.............................................................................. 19

4.13.1 Transporting the Moisture Analyzer.................................................................. 19

4.13.2 Putting into operation after transport................................................................ 19

4.13.3 Packaging and storing................................................................................... 19

4.14 Installing USB device driver........................................................................................... 20

5 Operating Elements and Interfaces 21

5.1 Operation keys ............................................................................................................ 21

5.2 Electrical interfaces ...................................................................................................... 21

6 Operation 23

6.1 Operation orientation.................................................................................................... 23

6.2 User interface .............................................................................................................. 23

6.2.1 Operation Keys ............................................................................................. 23

6.2.2 Screen navigation ......................................................................................... 23

6.2.3 Basic elements on the touch screen ................................................................ 24

6.2.4 Icons and buttons ......................................................................................... 24

6.2.4.1 Status message icons.............................................................................. 24

6.2.4.2 Title bar icons......................................................................................... 25

6.2.4.3 Action bar buttons ................................................................................... 25

6.2.5 Home Screen................................................................................................ 25

6.2.6 Work Screen................................................................................................. 26

6.2.7 Input dialogs ................................................................................................ 27

6.2.7.1 Entering characters and numbers.............................................................. 27

6.2.7.2 Entering numerical values ........................................................................ 28

6.2.7.3 Changing date and time........................................................................... 28

6.2.8 Lists and tables ............................................................................................ 29

6.3 Performing a Simple Measurement................................................................................. 30

Table of Contents 1Moisture Analyzer

7 Software Description 34

7.1 Method Definition......................................................................................................... 34

7.1.1 Method parameters ....................................................................................... 34

7.1.1.1 Main measurement parameters................................................................. 34

7.1.1.2 Result and value handling........................................................................ 44

7.1.1.3 Workflow handling .................................................................................. 47

7.1.1.4 General method properties........................................................................ 49

7.1.2 Creating a method......................................................................................... 50

7.1.2.1 Creating a method with the Method Wizard ................................................ 50

7.1.2.2 Creating a method manually..................................................................... 51

7.1.2.3 Creating a method by consulting the method library .................................... 51

7.1.3 Editing a method........................................................................................... 52

7.1.4 Testing a method .......................................................................................... 53

7.1.4.1 Temperature assistant.............................................................................. 53

7.1.4.2 Test measurement................................................................................... 54

7.1.4.3 Testing with AutoMet................................................................................ 55

7.1.5 Preparing a method for QuickPredict ............................................................... 55

7.1.5.1 Prerequisites to use QuickPredict for a method............................................ 56

7.1.5.2 Activating QuickPredict............................................................................. 57

7.1.5.3 Establishing the prediction knowledge ....................................................... 59

7.2 Measurement .............................................................................................................. 62

7.2.1 Performing a measurement ............................................................................ 62

7.2.2 Optimum sample preparation ......................................................................... 64

7.2.3 Working with weighing-in aid ......................................................................... 65

7.2.4 Working with QuickPredict ............................................................................. 65

7.2.4.1 Performing measurements with QuickPredict .............................................. 65

7.2.4.2 Handling QuickPredict results ................................................................... 68

7.2.4.3 Working with uncertainty thresholds .......................................................... 69

7.2.5 Working with shortcuts .................................................................................. 69

7.3 Results ....................................................................................................................... 70

7.3.1 Graphical evaluations of measurement results.................................................. 70

7.3.2 Method versioning......................................................................................... 73

7.3.3 Exporting results ........................................................................................... 73

7.3.3.1 Exporting results to a USB storage device................................................... 74

7.3.3.2 Exporting results with EasyDirect Moisture.................................................. 74

7.3.3.3 Exporting results via FTP server................................................................. 74

7.3.3.4 Export settings ........................................................................................ 75

7.4 Test/Adjust .................................................................................................................. 76

7.4.1 Tests ........................................................................................................... 77

7.4.1.1 Weight test - internal................................................................................ 77

7.4.1.2 Weight test - external............................................................................... 77

7.4.1.3 Weight test - Repeatability external............................................................ 78

7.4.1.4 Temperature test...................................................................................... 79

7.4.1.5 SmartCal test .......................................................................................... 80

7.4.1.6 Measures after failed test.......................................................................... 82

7.4.2 Adjustments ................................................................................................. 82

7.4.2.1 Fully automatic adjustment (FACT)............................................................ 82

7.4.2.2 Weight adjustment - internal..................................................................... 82

7.4.2.3 Weight adjustment - external .................................................................... 83

7.4.2.4 Temperature adjustment........................................................................... 83

7.4.3 History......................................................................................................... 85

7.5 Settings ...................................................................................................................... 86

7.5.1 User preferences ........................................................................................... 87

7.5.1.1 Languages ............................................................................................. 87

7.5.1.2 Screen .................................................................................................. 88

7.5.1.3 Sound.................................................................................................... 89

7.5.1.4 Password............................................................................................... 89

Table of Contents2 Moisture Analyzer

7.5.2 Instrument settings ........................................................................................ 90

7.5.2.1 Regional settings..................................................................................... 90

7.5.2.2 Peripherals............................................................................................. 90

7.5.2.3 Default settings ....................................................................................... 92

7.5.2.4 Company information .............................................................................. 93

7.5.2.5 Touch screen adjustment ......................................................................... 93

7.5.2.6 Network interfaces................................................................................... 94

7.5.3 Applications settings...................................................................................... 98

7.5.3.1 Identifications management...................................................................... 98

7.5.3.2 Print and export management................................................................... 99

7.5.3.3 Method selection..................................................................................... 102

7.5.4 Quality management ..................................................................................... 103

7.5.4.1 Test / Adjustment settings......................................................................... 103

7.5.4.2 QuickPredict ........................................................................................... 107

7.5.5 User management......................................................................................... 108

7.5.5.1 Groups .................................................................................................. 108

7.5.5.2 Users..................................................................................................... 109

7.5.5.3 Account policies...................................................................................... 110

7.5.6 System and data management ....................................................................... 111

7.5.6.1 Result management................................................................................. 111

7.5.6.2 Export / Import........................................................................................ 111

7.5.6.3 Back up / Restore.................................................................................... 113

7.5.6.4 Export event logs..................................................................................... 113

7.5.6.5 License manager..................................................................................... 114

7.5.6.6 Reset ..................................................................................................... 114

7.5.6.7 Update................................................................................................... 115

7.5.7 Help and tutorials.......................................................................................... 115

7.5.7.1 Instrument tutorial ................................................................................... 115

8 Maintenance 116

8.1 Maintenance table........................................................................................................ 116

8.2 Cleaning..................................................................................................................... 116

8.2.1 Sample chamber........................................................................................... 117

8.2.2 Heating module ............................................................................................ 117

8.2.3 Fan grill ....................................................................................................... 120

8.2.4 Putting into operation after cleaning ................................................................ 120

8.3 Replacing the Dust filter................................................................................................ 120

8.4 Replacing the power line fuse........................................................................................ 120

8.5 Updating the software................................................................................................... 121

9 Troubleshooting 122

9.1 Malfunctions shown on the display................................................................................ 122

9.2 Malfunctions when operating the instrument.................................................................... 123

10 Accessories and Spare Parts 127

10.1 Accessories................................................................................................................. 127

10.2 Spare parts ................................................................................................................. 131

11 Technical Data 132

11.1 General data ............................................................................................................... 132

11.2 Model-specific data...................................................................................................... 133

11.3 Dimensions................................................................................................................. 134

11.3.1 Drying unit ................................................................................................... 134

11.3.2 Terminal ...................................................................................................... 135

11.4 Interfaces specification ................................................................................................. 135

11.4.1 RS232C....................................................................................................... 135

11.4.2 USB host...................................................................................................... 136

11.4.3 USB device................................................................................................... 136

Table of Contents 3Moisture Analyzer

12 Disposal 137

Index 139

Table of Contents4 Moisture Analyzer

Introduction 5Moisture Analyzer

1 Introduction

Thank you for purchasing a Halogen Moisture Analyzer from METTLER TOLEDO.

Your Moisture Analyzer is fast, reliable and offers a high level of operating convenience and useful functions to

facilitate determination of the moisture content of your samples.

The Moisture Analyzer conforms with all common standards and directives. It supports stipulations, work

techniques and result records as demanded by all international quality assurance systems, e.g. GLP (Good

Laboratory Practice), GMP (Good Manufacturing Practice). The instrument has a CE declaration of conformity

and METTLER TOLEDO as the manufacturer has been awarded ISO 9001 and ISO 14001 certification. This

provides you with the assurance that your capital investment is protected in the long term by a high product

quality and a comprehensive service package (repairs, maintenance, servicing, adjustment service).

EULA

The software in this product is licensed under the METTLER TOLEDO End

User License Agreement (EULA) for Software.

When using this product you agree to the terms of the EULA.

u www.mt.com/EULA

Finding more information

u www.mt.com/moisture

u www.mt.com/hxhs

Search for software

u http://www.mt.com/moisture-software

Software version

This document is based on the software version V2.40 / V3.10.

Search for documents u www.mt.com/library

For further questions, please contact your authorized METTLER TOLEDO dealer or service representative.

u www.mt.com/contact

Conventions and symbols

Key and button designations are indicated by a picture or bold text (e.g. Save).

Refers to an external document.

Note

For useful information about the product.

Elements of instructions

In this manual, step-by-step instructions are presented as follows. The action steps are numbered and can

contain prerequisites, intermediate results and results, as shown in the example. Sequences with less than two

steps are not numbered.

§

Prerequisites that must be fulfilled before the individual steps can be executed.

1 Step 1

ð Intermediate result

2 Step 2

ð Result

Safety Information6 Moisture Analyzer

2 Safety Information

Two documents named "User Manual" and "Reference Manual" are available for this instrument.

• The User Manual is printed and delivered with the instrument.

• The electronic Reference Manual contains a full description of the instrument and its use.

• Keep both documents for future reference.

• Include both documents if you transfer the instrument to other parties.

Only use the instrument according to the User Manual and the Reference Manual. If you do not use the

instrument according to these documents or if the instrument is modified, the safety of the instrument may be

impaired and Mettler-Toledo GmbH assumes no liability.

2.1 Definition of signal warnings and symbols

Safety notes contain important information on safety issues. Ignoring the safety notes may lead to personal

injury, damage to the instrument, malfunctions and false results. Safety notes are marked with the following

signal words and warning symbols:

Signal words

WARNING

A hazardous situation with medium risk, possibly resulting in death or severe injury if

not avoided.

CAUTION

A hazardous situation with low risk, resulting in minor or moderate injury if not avoided.

NOTICE

A hazardous situation with low risk, resulting in damage to the instrument, other

material damage, malfunctions and erroneous results, or loss of data.

Warning symbols

General hazard: read the User Manual or the Reference Manual for information about the hazards

and the resulting measures.

Hot surface Notice

2.2 Product specific safety information

Intended use

This instrument is designed to be used by trained staff. The instrument is intended for determining the weight

loss during drying of samples.

Any other type of use and operation beyond the limits of use stated by Mettler-Toledo GmbH without consent

from Mettler-Toledo GmbH is considered as not intended.

Moisture determination applications must be optimized and validated by the user according to local

regulations. Application-specific data provided by METTLER TOLEDO is intended for guidance only.

Responsibilities of the instrument owner

The instrument owner is the person holding the legal title to the instrument and who uses the instrument or

authorizes any person to use it, or the person who is deemed by law to be the operator of the instrument. The

instrument owner is responsible for the safety of all users of the instrument and third parties.

METTLER TOLEDO assumes that the instrument owner trains users to safely use the instrument in their

workplace and deal with potential hazards. METTLER TOLEDO assumes that the instrument owner provides the

necessary protective gear.

Safety Information 7Moisture Analyzer

Personal protective equipment

Insulated gloves Lab coat

Goggles

Safety notes

WARNING

Death or serious injury due to electric shock

Contact with parts that carry a live current can lead to injury and death. If the instrument

cannot be shut down in an emergency situation, people can be injured and the instrument

can be damaged.

1 Check that the voltage printed on the instrument is the same as your local power supply

voltage. If this is not the case, under no circumstances connect the instrument to the

power supply, but contact a METTLER TOLEDO representative.

2 Only use the three-core power cable with equipment grounding conductor supplied by

METTLER TOLEDO to connect your instrument.

3 Only connect it to a three-pin power socket with earthing contact.

4 Only use standardized extension cables with equipment grounding conductor for

operating the instrument.

5 Make sure that the power plug is accessible at all times.

6 Arrange the cables so that they cannot be damaged or interfere with the operation.

7 Keep all electrical cables and connections away from liquids.

WARNING

Injury or death due to toxic or corrosive substances

Heating up toxic or corrosive substances, e.g., acids, can result in toxic or corrosive vapors

that can cause injuries if they come in contact with the skin or the eyes or if they are

inhaled.

1 When using chemicals and solvents, comply with the instructions of the manufacturer

and the general laboratory safety rules.

2 Set up the instrument in a well-ventilated location.

3 When using dry substances that form toxic gases, place the instrument in a fume hood.

WARNING

Death or serious injuries due to flammable solvents

Flammable solvents in the vicinity of the instrument can ignite and lead to fire and

explosions.

1 Keep flammable solvents away from the instrument.

2 When using chemicals and solvents, comply with the instructions of the manufacturer

and the general laboratory safety rules.

Safety Information8 Moisture Analyzer

CAUTION

Burns due to hot surfaces

During operation, parts of the instrument can reach temperatures that can cause burns if

touched.

1 Do not touch the area marked with the warning symbol.

2 Ensure sufficient free space around the instrument to avoid heat accumulation and

overheating (approx. 1 m free space above the heating module).

3 Never cover, tape or clog the vent over the sample chamber. Do not tamper with the vent

in any other way.

4 Exercise caution when removing a sample. The sample itself, the sample chamber, the

draft shield and the sample pan may be very hot.

5 Do not open the heating module during operation. Always let it cool down completely

before opening.

6 Do not modify the heating module in any way.

NOTICE

Damage to the instrument due to corrosive substances and vapors

Corrosive substances and corrosive vapors can damage the instrument.

1 When using chemicals and solvents, comply with the instructions of the manufacturer

and the general laboratory safety rules.

2 Ensure that the instrument parts touching your sample substance can not get altered by

it.

3 Wipe off any condensation of corrosive vapours after an operation.

4 Work with small samples.

NOTICE

Damage to the instrument due to the use of unsuitable parts

Using unsuitable parts with the instrument can damage the instrument or cause it to

malfunction.

− Only use parts from METTLER TOLEDO that are intended to be used with your

instrument.

For related information concerning the QuickPredict function, see [Prerequisites to use QuickPredict for a

method}Page56].

Design and Function 9Moisture Analyzer

3 Design and Function

In order to work with your Moisture Analyzer, you need to familiarize yourself with the instrument layout, drying

unit, graphical user interface of the touch screen as well as the terminal.

3.1 Overview

3.1.1 Overview drying unit

Legend drying unit

1

Heating module (with thermal overload

protection)

2

Handles for opening the sample chamber

3

Power contacts for halogen lamp

4

Draft shield element

5

Sample chamber

6

Level indicator / Level sensor

7

Leveling screw

8

Sample pan handler

9

Sample pan holder

10

Contacts for temperature kit (optional)

11

Temperature sensor

12

Inspection window and vent

13

2 Aux ports (n.a.)

14

Socket for terminal connection cable

15

Fastening for terminal stand

16

Fan

17

RS232C (for production only)

18

Dust filter (optional)

19

Kensington slot for anti-theft purposes

20

Power supply socket

21

Power line fuse (plus replacement fuse)

Design and Function10 Moisture Analyzer

3.1.2 Overview terminal

Legend terminal

1

Touch screen

2

USB Host port 1

3

Foot

4

USB Host port 2

5

USB Device port

6

RS232C port

7

Ethernet RJ45 port

8

Socket for terminal connection cable

9

SD Memory Card slot

3.1.3 Overview type plates

Drying unit type plate

The type plate of the drying unit is located on the side of the drying unit and contains the following information:

5

1

4

6

7

2 3

1

Model designation

2

Readability

3

Maximum capacity

4

Manufacturer

5

Power supply

6

Year of manufacture

7

Serial number (SNR)

Design and Function 11Moisture Analyzer

Terminal type plate

The type plate of the terminal is located on the terminal and contains the following information:

1

2

1

Model designation

2

Serial number (SNR)

3.2 Compliance Information

European Union

The instrument complies with the directives and standards listed on the EU Declaration of Conformity.

United States of America

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-

ference when the equipment is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

The FCC Supplier Declaration of Conformity is available online.

u http://www.mt.com/ComplianceSearch

3.3 Function description

METTLER TOLEDO Moisture Analyzers work on the thermogravimetric principle. At the start of the measurement

the Moisture Analyzer determines the weight of the sample, the sample is then quickly heated by the absorption

of the emitted infrared radiation. During the drying process the instrument continually measures the weight of

the sample and displays the weight reduction, up to the final result.

120 °

C

With halogen heating technology, maximum heating power is quickly reached and allows use of high temper-

atures. Uniform heating of the sample material ensures repeatability of the drying results and makes it possible

to use small amounts of sample.

The METTLER TOLEDO Moisture portfolio comprises a range of moisture analyzers that differ from each other in

both hardware and software.

The following features are available for the HX204 model:

• Accurate results for all sample types and repeatable moisture results thanks to 0.001% moisture content

readability.

Design and Function12 Moisture Analyzer

• Increased safety and process control: management of multiple users with individual access rights and

automatic lock-out option. See [User management}Page108]

• Increased efficiency and adherence to SOPs and regulations with Zero results option.

• Built-in testing methods to ensure performance: FACT, SmartCal and tests for the heating and weighing unit.

See [Test/Adjust}Page76]

• Reduced measurement time and quick decision making with the embedded QuickPredict

TM

function. See

[Working with QuickPredict}Page65]

• Integrated method development support. See [Creating a method}Page50]

• Quick and easy cleaning. See [Cleaning}Page116]

• Network connectivity. See [Electrical interfaces}Page21] and [Network interfaces}Page94]

• Level control. See [Leveling the instrument}Page16]

• Simple system integration and automation.

• Tailor-made reporting. See [Exporting results}Page73]

• ID management. See [Identifications management}Page98]

• Control limits. See [Control limits}Page44]

Installation and Putting into Operation 13Moisture Analyzer

4 Installation and Putting into Operation

4.1 Selecting the location

Requirements of the location

Place indoors on stable

table

Ensure sufficient spacing Level the instrument Provide adequate lighting

Avoid direct sunlight Avoid vibrations Avoid strong drafts Avoid temperature fluctu-

ations

Sufficient distance for Moisture Analyzers: > 15 cm next to the instrument, > 1 m above the heating module.

4.2 Unpacking

Note

Store all parts of the packaging. This packaging guarantees the best possible protection for the transport of your

instrument.

After receiving the instrument, proceed as follows:

1 Open the package and remove drying unit, terminal and the accessories.

2 Remove the packaging from the instrument.

3 Check the Moisture Analyzer for transport damage and complete scope of delivery.

4 In the event of damage or missing accessories, immediately inform a METTLER TOLEDO representative.

4.3 Scope of delivery

Moisture Analyzer Documentation Accessories

• 1 Drying unit

• 1 Draft shield

• 1 Power cable

• 1 Terminal cable

• 1 Sample handler

• 1 Sample pan holder

• 1 User Manual

• 1 Application brochure «Guide

to Moisture Analysis»

• 1 Production certificate

• 1 Voucher for E-learning "Proper

Moisture Determination"

• EU-countries: 1 CE declaration

of conformity

• 80 aluminium sample pans

• 3 Specimen samples (glass

fibre filter)

• 1 SmartCal sampler

• Specific countries: 1 Wifi dongle

Installation and Putting into Operation14 Moisture Analyzer

4.4 Connecting the instrument

WARNING

Death or serious injury due to electric shock

Contact with parts that carry a live current can lead to injury and death. If the instrument

cannot be shut down in an emergency situation, people can be injured and the instrument

can be damaged.

1 Check that the voltage printed on the instrument is the same as your local power supply

voltage. If this is not the case, under no circumstances connect the instrument to the

power supply, but contact a METTLER TOLEDO representative.

2 Only use the three-core power cable with equipment grounding conductor supplied by

METTLER TOLEDO to connect your instrument.

3 Only connect it to a three-pin power socket with earthing contact.

4 Only use standardized extension cables with equipment grounding conductor for

operating the instrument.

5 Make sure that the power plug is accessible at all times.

6 Arrange the cables so that they cannot be damaged or interfere with the operation.

7 Keep all electrical cables and connections away from liquids.

Two different versions of drying units with country-specific power cable are available:

110VAC or 230VAC

Connecting the terminal to the drying unit

§

Drying unit and terminal are at the final location.

1 Connect one end of the supplied terminal cable to the system connection socket on the terminal.

2 Screw the connector firmly.

3 Connect the other end to the system connection socket on the drying unit.

4 Screw the connector firmly.

Connecting the drying unit to the power supply

§

The terminal is connected to the drying unit.

1 Connect one end of the power cable to the power supply socket on the drying unit.

2 Connect the other end to the power line outlet.

Mettler Toledo HX204 Halogen Moisture Analyzer Operating instructions

Mettler Toledo HX204 Halogen Moisture Analyzer Operating instructions

Related papers

Other documents