Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Assembly and installation procedure
Refer to Fig. 1.
Adjusting the projection position
Refer to Fig. 2.
Applicable Projector Model Nos.
7215 7210 5210
INSTALLATION
CAUTIONS
●
Make sure to install this mounting hanger from a ceiling that is level. Do not hang it from
an inclined ceiling.
●
In order to prevent swaying caused by earthquakes or vibration, take proper anti-swaying
steps using wires, etc. during installation.
The total weight of this mounting hanger’s main body is 1.7 kg.
Parts included
in package
Mounting Hanger for Low Ceilings
Assembly/Installation Manual
LV-CL08
Make sure to ask a company specializing in installation work to install the hanger.
This mounting hanger is specifically for the projectors shown above. It cannot be used for any
other equipment. Do not place or hang any other object on this mounting hanger. Do not let
children hang on it. Assemble and install this mounting hanger correctly in accordance with this
manual. Make sure to observe the cautions given here.
When displaying the projector by hanging it from the ceiling using this mounting hanger, the
ceiling should have sufficient strength to support both the projector and the mounting
hanger. Before installation, check the weight of the projector and the mounting hanger, then
confirm the strength of the ceiling. If the ceiling does not have sufficient strength, be sure
to sufficiently reinforce it.
1. Turn over the projector main body, and attach it to the main body mounting fitting with screws (A)and (B).
(screw (A) … 3 pcs.)(screw (B) … 1 pc.)
2. Attach the drop prevention wires.
3. Attach the ceiling mounting fitting to the ceiling. Refer to the ceiling hanging fitting attachment dimensional
drawing.
4. Slide the main body mounting fitting to which the projector is attached into the ceiling hanging fitting that is
attached to the ceiling. Then fix the main body mounting fitting securely to the ceiling hanging fitting with four (A)
screws included in the package.
Caution : During this procedure, take care not to drop the projector. Since the projector is hung only
temporarily, it is not yet secured.
When wiring, make sure not to let cables or other items block the air inlet or the exhaust port.
This may raise the inside temperature and result in a malfunction.
Adjust the projection position so that an image is projected in the center of the screen. Then tighten the angle
adjusting screws securely using the hexagon wrench included in the package.
(If fine adjustment of the angle cannot be smoothly attained, loosen the angle adjusting screws with the hexagon
wrench. Then use the angle fine-adjustment screw. This will allow smooth fine adjustment.)
Screw (A)
...
11 pcs. Screw (B)
...
1 pc. Wire
...
2 pcs. Hexagon wrench
...
1 pc. Assembly/
Installation Manual
取付ハンガー(LV-CL08) 03.8.26 7:40 PM ページ5
Fig. 1 Assembly
Measures to prevent the projector from falling
* Make sure to take measures to prevent the projector main body from falling as explained here.
Wire
clamp
A Screws
(included in package)
Wire
(included in package)
Adjuster
cv
x
z
Projector main body
Screws (A)
Plus screw with round head M4 x 12 (3 pcs.)
with spring washer and flat washer
Screw (B)
Plus screw with round head
M4 x 40 (1 pc.) with spring washer
and flat washer
Main body mounting fitting (1 pc.)
Ceiling hanging
fitting
Main body mounting
fitting
1. Pull out the adjuster from the
projector main body.
2. Hang securely the drop
prevention wire included in the
package to the adjuster in the
main body (2 positions).
3. Tighten securely the wire clamp
with the drop prevention wire,
and push down the adjuster in
the main body.
4. Attach the drop prevention wire to
the main body mounting fitting
with two A screws (M4 x 12 mm)
included in the package. Attach
the drop prevention wire on the
opposite side in the same way.
Fix securely the main body
mounting fitting to the ceiling
hanging fitting with four A
screws (M4 x 12 mm)
included in the package.
2
取付ハンガー(LV-CL08) 03.8.26 7:40 PM ページ6
Fig. 2 Adjustment
CAUTION
After adjustment, confirm that the projector is fixed securely.
If the angle is not proper, adjust the angle again.
Rotated 360° to the left and right.
15° 15°
Tilted 15° in the 360° rotation range.
Angle adjusting screws
(with hexagon socket)
Angle fine-adjusting screw
This screw facilitates fine adjustment of the projection
angle while the projector is half fixed.
After determining the projection angle, make sure to fix
securely the projector with the angle adjusting screws.
After the projector angle is fixed once, if the angle is adjusted
again in the fixed status, the fixed area may be deformed and
adjustment might no longer be possible. Loosen the angle
adjusting screws before adjusting the angle again.
3
取付ハンガー(LV-CL08) 03.8.26 7:40 PM ページ7
(Unit: mm)
(Unit: mm)
■ Approximate projection distance
40
1.0m
1.6m
60
1.5m
2.4m
70
1.8m
2.8m
80
2.0m
3.2m
90
2.3m
3.6m
100
2.5m
4.0m
110
2.8m
4.4m
120
3.1m
4.8m
150
3.8m
6.0m
200
5.1m
250
6.4m
300
7.7mMaximum zoom
Screen size
(diagonal)(inch)
Minimum zoom
* Each approximate projection distance is a calculated value based on lens design specifications.
An error of approximately 5% maximum may occur due to lens quality, etc.
Ceiling hanging fitting mounting dimensions
Front view Side view
80
72
106
88
90
185.5
Hole 4-ø9
43.5
173
105
127.5
122
206.5
4
取付ハンガー(LV-CL08) 03.8.26 7:40 PM ページ8
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Canon LV-5210 Owner's manual
- Category
- Projector accessories
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- 日本語: Canon LV-5210 取扱説明書
Related papers
Other documents
-
NEC NP09CM User guide
-
IBM M400 User manual
-
BenQ Universal Ceiling Mount Installation guide
-
Sanyo POA-CHL-PL01 Assembly And Installation Manual
-
NEC NP04CM User manual
-
-
CAME MR8003 User manual
-
Niigata seiki LS2-175S User manual
-
Fostex EX-12 User manual
-