Dell PowerEdge 7150 Owner's manual

Brand: Dell

Model: PowerEdge 7150

Type: Owner's manual

Dell™PowerEdge™7150SystemsUser'sGuide 
System Overview 
Computer Orientation  
Removing and Replacing the Bezel  
Front-Panel Features  
Bezel and Control Panel Indicators  
Back-Panel Features  
System Features  
Power Protection Devices  
Other Documents You May Need  
Safety, Regulatory, and Warranty Information  
Getting Help  
Using the EFI Boot Manager and Dell Utilities 
EFI Boot Manager  
Dell Utilities  
PowerEdge 7150 System Support CD  
Updating or Restoring the System BIOS  
Using the System Setup Program 
Entering the System Setup Program  
System Setup Screens  
Using the Password Features  
Disabling a Forgotten Password  
Technical Specifications 
I/O Ports and Connectors 
Serial and Parallel Ports  
Keyboard and Mouse Connectors  
Video Connector  
USB Connectors  
Integrated Network Interface Controller Connector  
Glossary 
Figures 
Tables 
Notes, Notices, Cautions, and Warnings 
Model EML 
Information in this document is subject to change without notice. 
©2000 Dell Computer Corporation. All rights reserved. 
Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. 
Trademarks used in this text: Dell, the DELL logo, PowerEdge, and Dell OpenManage are trademarks of Dell Computer Corporation; Intel is a registered trademark and Itanium is a trademark of of Intel Corporation; Microsoft is a registered 
trademark of Microsoft Corporation. 
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its 
own. 
Initial release: 13 Dec 2000 
 
NOTE: A NOTE indicates important information that helps you make better use of your computer. 
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. 
 
CAUTION: A CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. 
WARNING: A WARNING indicates a potentially hazardous situation which, if not avoided, may result in severe injury. 

Back to Contents Page

Technical Specifications

Dell™PowerEdge™7150SystemsUser'sGuide



Table A-1. Technical Specifications

Microprocessor

Microprocessor type

one to four Intel 64-bit Intel

Itanium™microprocessorswithaminimuminternaloperatingfrequencyof733MHzandanexternal

operating frequency of 133 MHz

Front side bus speed

133 MHz (266 MHz double-pumped)

Internal cache

2- or 4-MB L3 cache

Expansion Bus

Bus type

64-bit PCI

Expansion slots

Eight 66-MHz hot-pluggable slots on six PCI buses; two 33-MHz slots on a seventh PCI bus

Memory

Architecture

registered PC-100-compliant DIMMs with CL2 timing

Memory module sockets

32 sockets per memory board; one or two memory boards

Memory module capacities

128-MB, 256-, or 512-MB; or 1-GB (when available)

Minimum RAM

1 GB

Maximum RAM

64 GB (when 1-GB memory modules are available)

Drives

Diskette drive

one IDE diskette drive

Tape drive

optional external tape drive

SCSI devices

up to four 1-inch, internal, hot-pluggable Ultra3 SCSI hard-disk drives

CD-ROM drive

one IDE CD-ROM drive

Ports and Connectors

Externally accessible:

Serial (DTE)

two 9-pin connectors; 16550-compatible

Parallel

one 25-pin connector (bidirectional)

Video

one 15-pin connector

PS/2-style keyboard

6-pin mini-DIN connector

PS/2-compatible

mouse

6-pin mini-DIN connector

USB

two USB-compliant 4-pin connectors

NIC

RJ45 connector for integrated NIC

SCSI

One 68-pin Ultra3 SCSI connector

ICMB

(Not supported)

Internally accessible:

IDE channels

two 40-pin connectors

SCSI channels

two 68-pin Ultra3 SCSI connectors

Video

Video type

ATI Rage 128 XL video controller; VGA connector

Video memory (standard)

8 MB

Power1

DC power supply:



Wattage

four 800 W power supplies in a 3 +1 redundant configuration

Voltage

200-240V, 50/60 Hz

optional 100-240V, 50/60 Hz

System battery

CR2032 3.0-V lithium coin cell

Back to Contents Page



Physical

Height

31.12 cm (12.25 inches [7 U])

Width

44.45 cm (17.5 inches)

Depth

71.12 cm (28.0 inches)

Weight

72.5 kg (160 lb), maximum configuration

Environmental

Temperature:



Operating

10°to35°C(50°to95°F)

Storage

-40°to65°C

(-40°to149°F)

Relative humidity:



Operating

85%(noncondensingat40°C[104°F])

Storage

95%(noncondensingat55°C[131°F])

NOTE:

Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 140A.

NOTE:

Limitthenumberoftransitionsacross0°Ctonomorethan50.

NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary.

Back to Contents Page 
I/O Ports and Connectors  
Dell™PowerEdge™7150SystemsUser'sGuide 
Serial and Parallel Ports 
Keyboard and Mouse Connectors 
Video Connector 
USB Connectors 
Integrated Network Interface Controller Connector 
This section provides specific information about the computer's I/O ports. 
The I/O ports and connectors on the back panel of the computer are the gateways through which the computer system communicates with external devices, such as a 
keyboard, mouse, printer, and monitor. FigureB-1 identifies the I/O ports and connectors for your system. 
Figure B-1. Back-Panel Features  

 
Serial and Parallel Ports 
The two integrated serial ports use 9-pin D-subminiature connectors on the back panel. These ports support devices such as external modems, printers, plotters, and 
mice that require serial data transmission (the transmission of data one bit at a time over one line). 
Most software uses the term COM (for communications) plus a number to designate a serial port (for example, COM1 or COM2). The default designations of your 
computer'sintegratedserialportsareCOM1andCOM2. 
The integrated parallel port uses a 25-pin D-subminiature connector on the computer's back panel. This I/O port sends data in parallel format (where eight data bits, or 
one byte, are sent simultaneously over eight separate lines in a single cable). The parallel port is used primarily for printers. 
Most software uses the term LPT (for line printer) plus a number to designate a parallel port (for example, LPT1). The default designation of the computer's integrated 
parallel port is LPT1. 
Port designations are used, for example, in software installation procedures that include a step in which you identify the port to which a printer is attached, thus telling 
the software where to send its output. (An incorrect designation prevents the printer from printing or causes scrambled print.) 
Serial Port Connectors 
If you reconfigure your hardware, you may need pin number and signal information for the serial port connectors. FigureB-2 illustrates the pin numbers for the serial 
port connectors and TableB-1 defines the pin assignments and interface signals for the serial port connector. 
Figure B-2. Pin Numbers for the Serial Port Connectors  




Parallel Port Connector

If you reconfigure your hardware, you may need pin number and signal information for the parallel port connector. FigureB-3 illustrates the pin numbers for the parallel

port connector and TableB-2 defines the pin assignments and interface signals for the parallel port connector.

Figure B-3. Pin Numbers for the Parallel Port Connector



Table B-1. Pin Numbers for the Serial Port

Connectors

Signal

I/O

Definition

DCD

Data carrier detect

SIN

Serial input

SOUT

Serial output

DTR

Data terminal ready

GND

N/A

Signal ground

DSR

Data set ready

RTS

Request to send

CTS

Clear to send

Ring indicator

Shell

N/A

Chassis ground



Table B-2. Parallel Port Pin Assignments

Signal

I/O

Definition

STB#

I/O

Strobe

PD0

I/O

Printer data bit 0

PD1

I/O

Printer data bit 1

PD2

I/O

Printer data bit 2

PD3

I/O

Printer data bit 3

PD4

I/O

Printer data bit 4

PD5

I/O

Printer data bit 5

Keyboard and Mouse Connectors

The system uses a Personal System/2 (PS/2)-style keyboard and supports a

PS/2-compatible mouse. Cables from both devices attach to 6-pin, miniature Deutsche Industrie Norm (DIN) connectors on the back panel of your computer.

Mouse driver software can give the mouse priority with the microprocessor by issuing IRQ12 whenever a new mouse movement is detected. The driver software also

passes along the mouse data to the application program that is in control.

Keyboard Connector

If you reconfigure your hardware, you may need pin number and signal information for the keyboard connector. FigureB-4 illustrates the pin numbers for the keyboard

connector and TableB-3 defines the pin assignments and interface signals for the keyboard connector.

Figure B-4. Pin Numbers for the Keyboard Connector



Mouse Connector

If you reconfigure your hardware, you may need pin number and signal information for the mouse connector. FigureB-5 illustrates the pin numbers for the mouse

connector, and TableB-4 defines the pin assignments and interface signals for the mouse connector.

Figure B-5. Pin Numbers for the Mouse Connector



PD6

I/O

Printer data bit 6

PD7

I/O

Printer data bit 7

ACK#

Acknowledge

BUSY

Busy

Paper end

SLCT

Select

AFD#

Automatic feed

ERR#

Error

INIT#

Initialize printer

SLIN#

Select in

18–25

GND

N/A

Signalground

Table B-3.KeyboardConnectorPinAssignments

Signal

I/O

Definition

KBDATA

I/O

Keyboard data

N/A

No connection

GND

N/A

Signal ground

FVcc

N/A

Fused supply voltage

KBCLK

I/O

Keyboard clock

N/A

No connection

Shell

N/A

Chassis ground



Video Connector

The system uses a 15-pin high-density D-subminiature connector on the back panel for attaching a video graphics array (VGA)-compatible monitor to your computer.

The video circuitry on the system board synchronizes the signals that drive the red, green, and blue electron guns in the monitor.

If you reconfigure your hardware, you may need pin number and signal information for the video connector. FigureB-6 illustrates the pin numbers for the video

connector, and TableB-5 defines the pin assignments and interface signals for the video connector.

Figure B-6. Pin Numbers for the Video Connector



USB Connectors

Your system contains two USB connectors for attaching USB-compliant devices. USB devices are typically peripherals such as mice, printers, keyboards, and

computer speakers.

Table B-4.MouseConnectorPinAssignments

Signal

I/O

Definition

MCDATA

I/O

Mouse data

N/A

No connection

GND

N/A

Signal ground

FVcc

N/A

Fusedsupplyvoltage

MCCLK

I/O

Mouse clock

N/A

No connection

Shell

N/A

Chassis ground

NOTE: Installing a video card automatically disables the system's integrated video subsystem.

Table B-5. Video Connector Pin Assignments

Signal

I/O

Definition

RED

Red video

GREEN

Green video

BLUE

Blue video

N/A

No connection

5–8, 10

GND

N/A

Signal ground

VCC

N/A

Vcc

N/A

No connection

DDC data out

Monitor detect data

HSYNC

Horizontal synchronization

VSYNC

Vertical synchronization

If you reconfigure your hardware, you may need pin number and signal information for the USB connectors. FigureB-7 illustrates the USB connector and TableB-6

defines the pin assignments and interface signals for the USB connector.

Figure B-7. Pin Numbers for the USB Connector



Integrated Network Interface Controller Connector

Your system has an integrated 10/100–Mbps NIC. The NIC provides all the functions of a separate network expansion card and supports both the 10BASE-T and

100BASE-TX Ethernet standards.

Figure B-8. NIC Connector



The NIC includes a Wake On LAN (WOL) feature that enables the computer to be started by a special LAN signal from a server management console. WOL

provides remote computer setup, software downloading and installation, file updates, and asset tracking after hours and on weekends when LAN traffic is typically at a

minimum.

Network Cable Requirements

Your computer's RJ45 NIC connector is designed for attaching an unshielded twisted pair (UTP) Ethernet cable equipped with standard RJ45-compatible plugs. Press

one end of the UTP cable into the NIC connector until the plug snaps securely into place. Connect the other end of the cable to an RJ45 jack wall plate or to an RJ45

port on a UTP concentrator or hub, depending on your network configuration. Observe the following cabling restrictions for 10BASE-T and 100BASE-TX networks.

l For 10BASE-T networks, use Category 3 or greater wiring and connectors.

l For 100BASE-TX networks, use Category 5 or greater wiring and connectors.

l Themaximumcablerunlength(fromaworkstationtoaconcentrator)is328ft(100m).

l For 10BASE-T networks, the maximum number of daisy-chained concentrators on one network segment is four.

NOTICE: Do not attach a USB device or a combination of USB devices that draw a maximum current over 500 mA per channel or +5 V. Attaching devices

that exceed this threshold might cause the USB ports to shut down. See the documentation that accompanied the USB devices for their maximum current

ratings.

Table B-6.USBConnectorPinAssignments

Signal

I/O

Definition

Vcc

N/A

Supply voltage

-DATA

I/O

Differential data

+DATA

I/O

Differential data

GND

N/A

Signal ground

Shell

N/A

Chassis ground

NOTICE: To avoid line interference, voice and data lines must be in separate sheaths.

Back to Contents Page



Back to Contents Page 
System Overview  
Dell™PowerEdge™7150SystemsUser'sGuide 
TheDell™PowerEdge™7150systemisafeature-rich, enterprise-class server that offers the highest performance, availability, scalability, manageability, and 
investment protection features. This system provides a robust, reliable, rack-optimized platform on which corporate customers can deploy their mission-critical 
applications. 
This section describes the major hardware and software features of the computer system, provides information about the indicators on the system's bezel and control 
panel, and discusses connecting external devices to the system. It also provides information on obtaining assistance from Dell. 
Computer Orientation 
When following the procedures in this guide, assume that the locations or directions relative to the computer are as shown in Figure1-1. 
Figure 1-1. Computer Orientation (top view)  

 
Removing and Replacing the Bezel 
Removing the front bezel provides access to the power switch, diskette drive, control panel, CD-ROM drive, power supplies, and hard-disk drive(s).  
Removing the Bezel 
Pull the bezel away from the computer until it disengages from the four posts on the chassis (see Figure1-2). 
Figure 1-2. Removing the Bezel  

Computer Orientation 
Removing and Replacing the Bezel 
Front-Panel Features 
Bezel and Control Panel Indicators 
Back-Panel Features 
System Features 
Power Protection Devices 
Other Documents You May Need 
Safety, Regulatory, and Warranty Information 
Getting Help 

Replacing the Bezel

1. Align the four notches and the connector on the back of the bezel with the four posts and connector on the front of the system.

2. Gently press the bezel onto the front of the computer until it snaps into place.

Front-Panel Features

Figure1-3 shows the major features at the front of the computer.

Figure 1-3. Front-Panel Features



Bezel and Control Panel Indicators

The system bezel and control panel both have indicators to provide you with information on the system's status.

Bezel Indicators

When the bezel is in place on the system, it has two indicators (see Figure1-4). The Dell logo lights blue when the system is operating correctly. The caution icon lights

amber when the system needs attention. The amber caution light indicates a power problem, a fan/temperature problem, a hard drive problem, or that the PCI

expansion cards need attention. Remove the bezel to determine the source of the problem.

CAUTION: When reinstalling the front bezel, carefully align the bezel to avoid damaging the connector on the back which operates the indicator

lights on the front of the bezel.

Figure 1-4. Bezel Indicators



Control-Panel Indicators

The indicators on the computer's control panel described in Table1-1 are shown in Figure1-5:



Figure 1-5. Control-Panel Indicators



Table 1-1. Control-Panel Indicators

Indicator

Function

Power

Green when the power supplies are turned on and the system is receiving power

Power-Supply Status

Amber if a fault is detected with any of the power supplies, any system voltages, or redundant AC power line failure

Fan Status

Amber when a fan failure is detected or temperature is out of bounds

PCI Slot Attention

Amber when one or more or the PCI slots need attention.

Hard-disk drive fault

Amber if a problem occurs with one of the internal hard-disk drives

Display

System information messages during POST

Back-Panel Features

Figure1-6 shows the back-panel features on the computer.

Figure 1-6. Back-Panel Features



When connecting external devices to your system, follow these guidelines:

l Always attach external devices while your system is turned off and the AC power cords are unplugged. Turn on any external devices before turning on the

system unless the documentation for the device specifies otherwise. (If the system does not seem to recognize the device, try turning on the system before turning

on the device.)

l Check the documentation that accompanied the device for specific installation and configuration instructions. For example, most devices must be connected to a

particular connector to operate properly. Also, external devices usually require you to install device drivers before they will work. Device drivers are normally

included with your operating system software, or with the device itself.

For information about enabling, disabling, or configuring I/O ports and connectors, see "Using the System Setup Program" or "I/O Ports and Connectors."

System Features

Your PowerEdge system offers the following features:

l One to four Intel

Itanium

™

microprocessors.

l Front-side bus speed of 133 MHz (266 MHz double-pumped).

l Level 3 cache of 2 or 4 MB.

l Support for symmetric multiprocessing (SMP), which is available by installing up to three additional microprocessors.

l A minimum of 1 GB of system memory, upgradable to a maximum of 64 GB by installing combinations of 128-, 256-, or 512-MB or 1-GB (when available)

registered SDRAM memory modules in the 32 sockets on each of the two memory boards. The system supports 4-way interleaving if specific memory

configurations are used.

l Support for up to four 1-inch, internal, hot-pluggable Ultra SCSI hard-disk drives via a 1 x 4 or 2 x 2 SCSI backplane board and hard-disk drive carriers.

l Four hot-pluggable, 800 W power supplies in a 3 + 1 redundant configuration.

l An optional redundant 208-V power module.

l Six redundant, hot-pluggable system cooling fans.

The system's I/O board includes the following built-in features:

l Ten 64-bit, PCI expansion-card connectors on seven PCI buses. Eight of the expansion slots operate at 66 or 33 MHz and are hot-pluggable. These expansion

slots accommodate 3.3V or Universal (3.3 or 5V) expansion cards. The two remaining expansion slots operate at 33 MHz and are not hot-pluggable. You can

install 5V or Universal PCI cards in these two expansion slots. (An eleventh expansion slot is reserved for use by the system's I/O riser board.)

l AvideosubsystembasedontheATIRage128XLvideocontroller.Thisvideosubsystemresidesonthe33MHzPCIbusandcontains8MBofvideo

memory(notupgradable).Maximumresolutionsare1280x1024with256colorsnoninterlaced.In800x600and640x480resolutions,16.7millioncolors

are available for true-color graphics.

l Ultra3 SCSI device support via an integrated QLogic ISP12160A dual-channel controller.

l An integrated Intel 10/100 NIC, which provides an external Ethernet interface.

l Server management circuitry that monitors the operation of the system fans as well as critical system voltages and temperatures.

Standard systems include an IDE CD-ROM drive and a diskette drive installed in the externally accessible bays.

The following software is included with your Dell system:

l A system setup program for quickly viewing and changing the system configuration information for your system. For more information on this program, see

"Using the System Setup Program"

l An Extensible Firmware Interface (EFI) Boot Manager program which lets you access the EFI Shell command line prompt, a boot manager utility, and the Dell

Utilities.

l Enhanced security features, including chassis intrusion monitoring and a user password and a supervisor password, available through the system setup program.

l Dell Diagnostics for evaluating your system's components and devices. For information on using the system diagnostics, see "Running the Dell Diagnostics" in

your Installation and Troubleshooting Guide.

NOTE: If you decide to upgrade your system by installing additional microprocessors, you must order the microprocessor upgrade kits from Dell. Not all

versions of the microprocessor will work properly as additional microprocessors. The upgrade kit from Dell contains the correct version of the

microprocessor as well as the correct instructions for performing the upgrade. All microprocessors must have the same internal operating frequency and

cache size.

Power Protection Devices

A number of devices are available that protect against potential power problems such as power surges, transients, and power failures. The following subsections

describe some of these devices.

Surge Protectors

Surge protectors are available in a variety of types and usually provide a level of protection commensurate with the cost of the device. Surge protectors prevent voltage

spikes, such as those caused during an electrical storm, from entering a system through the electrical outlet. Surge protectors, however, do not offer protection against

brownouts, which occur when the voltage drops more than 20 percent below the normal AC line voltage level.

Line Conditioners

Line conditioners go beyond the overvoltage protection of surge protectors. Line conditioners keep a system's AC power source voltage at a fairly constant level and,

therefore, can handle brownouts. Because of this added protection, line conditioners cost more than surge protectors—up to several hundred dollars. However, these

devices cannot protect against a complete loss of power.

Uninterruptible Power Supplies

UPS systems offer the most complete protection against variations in power because they use battery power to keep the system running when AC power is lost. The

battery is charged by the AC power while it is available, so once AC power is lost, the battery can provide power to the system for a limited amount of time—from 15

minutes to an hour or so—depending on the UPS system.

UPS systems range in price from a few hundred dollars to several thousand dollars, with the more expensive units allowing you to run larger systems for a longer period

of time when AC power is lost. UPS systems that provide only 5 minutes of battery power let you conduct an orderly shutdown of the system, but are not intended to

provide continued operation. Surge protectors should be used with all UPS systems, and the UPS system should be UL safety-approved.

Other Documents You May Need

Besides this User's Guide, the following documentation is included with your system:

l The Setting Up Your System sheet provides general instructions for setting up your computer system.

l Dell PowerEdge 7150 Systems Installation and Troubleshooting Guide

l Dell PowerEdge System Information document for important safety, regulatory, and warranty information

l Dell PowerEdge 7150 Systems Rack Installation Guide

You might also have one or more of the following documents:

l Operating system documentation is included if you ordered your operating system software from Dell. This documentation describes how to install (if necessary),

configure, and use your operating system software.

l Documentation is included with any options you purchase separately from your system. This documentation includes information that you need to install and

configure these options in your Dell system. Installation instructions for the options are included in this User's Guide.

l Technical information files—sometimes called "readme" files—may be installed on your hard-disk drive to provide last-minute updates about technical changes

to your system or advanced technical reference material intended for experienced users or technicians.

Safety, Regulatory, and Warranty Information

For safety, regulatory, and warranty information for your system, see the System Information document included with your system.

Getting Help

If at any time you don't understand a procedure described in this guide or if your system does not perform as expected, Dell provides a number of tools to help you.

For more information on these help tools, see "Getting Help" in your Installation and Troubleshooting Guide.

Back to Contents Page

NOTE: Documentation updates are sometimes included with your system to describe changes to your system or software. Always read these updates before

consulting any other documentation because the updates often contain the latest information.



Back to Contents Page 
Using the EFI Boot Manager and Dell Utilities  
Dell™PowerEdge™7150SystemsUser'sGuide 
EFI Boot Manager  
Dell Utilities 
PowerEdge 7150 System Support CD 
Updating or Restoring the System BIOS 
This section describes your system's Extensible Firmware Interface (EFI) Boot Manager program, the PowerEdge 7150 System Support CD, and the Dell Utilities 
program. They provide access to various utilities which you may use to configure your system. 
EFI Boot Manager  
The EFI Boot Manager menu lets you access the operating systems installed on your system, a boot manager utility, and the Utilities menu. 
Entering the EFI Boot Manager 
1. Turn on your system by pressing the power button on the system front panel. 
 
If your system is already on, reboot it. 
2. Wait until the system tests are completed. 
 
The EFI Boot Manager screen appears. 
Selecting EFI Boot Manager Options 
From the EFI Boot Manager screen, you can select the following options: 
l Operating systems installed on your system 
 
l Boot Option Maintenance Manager Menu — Use this option to select which devices the system can be booted from, and their relative order. 
 
l Utilities — Select this option to go to the Utilities Option Menu. For more information on this menu, see "Utilities Option Menu."  
 
Utilities Option Menu 
This menu includes the following options: 
l EFI Shell — Use this option to run command-driven programs from the Shell prompt. 
 
l Dell Utilities — Select this option to run the Dell Utilities program. See "Dell Utilities" for more information on this program. 
 
l BIOS Update — Select this option to update the system BIOS to the latest version. See "Updating or Restoring the System BIOS" for more information on this 
program. 
 
l Firmware Update — Select this option to update the system firmware to the latest version. 
 
l Run Dell Diagnostics from diskette — Select this option to run the system hardware diagnostics. (For more information, see "Running the Dell Diagnostics" in 
your Installation and Troubleshooting Guide.) 
 
Dell Utilities 
The Dell Utilities include the Dell Diagnostics program, as well as features that can help you configure your system to best meet your needs. You run the utilities from 
an EFI System Partition that you can create on the system boot hard-disk drive, using the PowerEdge 7150 System Support CD. (See "PowerEdge 7150 System 
Support CD" for more information on this CD.) 
Starting the Dell Utilities 
If you have created an EFI System Partition on the system's boot hard-disk drive and installed the utilities on this partition, you can run the Dell Utilities. To run the Dell 
Utilities from the hard-disk drive, perform the following steps: 
1. Turn on your system by pressing the power button on the system front panel. 
 

If your system is already on, reboot it.

2. Wait until the system tests are completed.

The EFI Boot Manager screen appears.

3. From the EFI Boot Manager main menu, select Utilities.

4. From the Utilities Options menu, select Dell Utilities.

Selecting Dell Utilities Options

From the Dell Utilities menu, you can select options to perform the following tasks:

l Run the Dell Diagnostics program (The system hardware diagnostics are described in "Running the Dell Diagnostics" in your Installation and Troubleshooting

Guide.)

l Assign or change an asset tag number for your system. An asset tag number can have up to ten characters; any combination of characters, excluding spaces, is

valid.

l Run the System Event Log (SEL) Viewer

PowerEdge 7150 System Support CD

To access the utilities, drivers, and other items available on the PowerEdge 7150 System Support CD, insert the CD into the system's CD-ROM drive, and turn on or

reboot the system.

PowerEdge 7150 System Support CD Options

From the main menu, you can select options to perform the following tasks:

l Create an EFI System Partition on the boot hard-disk drive

l Copy the Dell Utilities to the EFI System Partition

l Copy drivers or system utilities to a diskette

l Run the Dell Diagnostics program (The system hardware diagnostics are described in "Running the Dell Diagnostics" in your Installation and Troubleshooting

Guide.)

Updating or Restoring the System BIOS

If necessary, you can restore the system BIOS or update the system BIOS to the latest version.

1. Before updating the BIOS, run the system setup program and note any option settings that vary from the default settings.

2. Download the updated BIOS files from http://support.dell.com onto the BIOS recovery diskette provided with your system.

3. Insert the BIOS recovery diskette into the diskette drive and reboot the system.

4. From the EFI Boot Manager menu, select the Utilities option.

5. Select the BIOS Update option and follow the on-screen instructions.

The system reboots automatically after the update process is completed.

6. Enter the system setup program by pressing <F2> when the Dell logo is displayed, and restore the options to their original settings.

Back to Contents Page



NOTE: If the CD does not boot, verify that the CD-ROM drive is specified in the boot sequence option in the EFI Boot Maintenance Manager program.



Back to Contents Page

Using the System Setup Program

Dell™PowerEdge™7150SystemsUser'sGuide

Entering the System Setup Program

System Setup Screens

Using the Password Features

Disabling a Forgotten Password

You can use the system setup program as follows:

l To change the system configuration information after you add, change, or remove hardware in your system

l To set or change user-selectable options—forexample,thetimeordateonyoursystem

l To configure integrated devices in your system

After you set up your system, run the system setup program to familiarize yourself with your system configuration information and optional settings. Dell recommends

that you record this information for future reference.

Entering the System Setup Program

1. Turn on your system by pressing the power button on the system front panel.

If your system is already on, shut it down and then turn it on again.

2. Press <F2> immediately after the Dell logo is displayed.

If you wait too long and your operating system begins to load into memory, let the system complete the load operation; shut down the system and try again.

You can also enter the system setup program by responding to certain error messages. See "Responding to Error Messages."

Responding to Error Messages

If an error message appears on your monitor screen while the system is booting, make a note of the message. Then, before entering the system setup program, see

"System Beep Codes" and "System Messages" in your Installation and Troubleshooting Guide for an explanation of the message and suggestions for correcting any

errors. (An exception to this routine: It is normal to receive an error message the first time you boot your system after installing a memory upgrade. In that situation, do

not refer to "System Beep Codes" and "System Messages." Instead, follow the instructions for performing a memory upgrade in "Adding Memory" in your Installation

and Troubleshooting Guide.)

If you are given an option of pressing either <F1> to continue or <F2> to run the system setup program, press <F2>.

Using the System Setup Program

Table3-1 lists the keys that you use to view or change information on the system setup screens and to exit the program.



NOTE: To ensure an orderly system shutdown, consult the documentation that accompanied your operating system.

Table 3-1.SystemSetupNavigationKeys

Keys

Action

Left and Right Arrows

Scrolls through the five main menu screens

<Enter>