In-Sink-Erator AS-2 User manual

In-Sink-Erator
Brand
In-Sink-Erator
Model
AS-2
Type
User manual

This manual is also suitable for

Start Date:
Engineer Number:
09/01/93
Aqua Saver
MODEL NO. AS -1(120V),-2(230V),-3(460V)
13759,60,61
CODE PART NO.
NO. NO. REQ. DESCRIPTION
ORDER BY PART NUMBER, NOT CODE NUMBER
4
AS-1, -2
3
1
2
5
AS-3
1 13757 1 Module, Current Sensing - (used on Models AS-1, AS-2)
2 13758 1 Module, Current Sensing - (used on Model AS-3)
3 13770 1 Transformer - (used on Model AS-3 only)
4 13763 1 Valve, Flow Control-1GPM
5 11475-A 1 Valve, Solenoid
Black
Black
Red
1 gpm
X gpm
Trip
delay
Trip
point
Fault
Orange
120V
Black
Black
Red
1 gpm
X gpm
Trip
delay
Trip
point
Fault
Orange
230V
Trip
delay
Trip
point
Fault
460V
Black
Black
Red
120V
X gpm
1 gpm
120
V
460
V
WARRANTY INFORMATION
Your In-Sink-Erator Aqua Saver system is warranted for ONE YEAR from date of installation. This warranty covers both parts
and labor for defects in workmanship or material only (provided the labor is performed by an In-Sink-Erator Factory Authorized Service
Agency).
This warranty does not apply if the Aqua Saver is installed with any commercial disposer other than those manufactured by
In-Sink-Erator. Also, the warranty does not apply if failure is due to faulty or improper electrical installation, faulty or improper plumbing
installation, abuse, or accidental damage.
To obtain service, call the nearest In-Sink-Erator Factory Authorized Service Agency. For the location of your nearest service
agency, call toll free in the USA 1-800-558-5700 or 1-800-561-1700 in Canada.
Blue
Blue
Red
Red
Blue
Orange
THE AQUA SAVER acts as an on-demand water
system for In-Sink-Erator commercial disposers. The
Aqua Saver System senses the load of the disposer
motor, and regulates the amount of water necessary
for grinding and non-grinding situations.
The AQUA SAVER SYSTEM includes one:
• Aqua Saver control module
• 1 GPM flow control valve
• 120/230V solenoid valve
FEATURES SPECIFICATIONS:
• Works with all In-Sink-Erator
commercial disposer models
• Designed for new and retrofit disposer
installations
• Available for 120V, 230V or 460V
applications
• Control module in a stainless steel
NEMA 4-water tight enclosure
• 1-year full warranty from date of
installation
* 6 lb. shipping weight
OPERATION
The aqua Saver System senses the load on the
disposer motor, and regulates the amount of water
necessary for grind and no grind load situations.
When the disposer is turned on and not grinding
food waste the water flow to the disposer should be at
a slow rate - 1 gallon per minute (GPM).
When the disposer is grinding food waste the
increased load is detected and the water flow rate
increases to insure that the food waste is flushed
through the drain lines.
When the disposer is finished grinding the water
flow decreases back to the slower rate of 1 GPM.
IMPORTANT
The 1 GPM flow control (included with Aqua
Saver) always plumbs to the solenoid valve supplied
with the disposer package, or the solenoid valve on an
existing disposer installation.
The X GPM flow control will be supplied as a
standard item with a new In-Sink-Erator disposer
package, or will be in-line in an existing disposer
installation. The Aqua Saver will work with out the X
GPM flow control, but it is recommended as part of the
installation. The X GPM flow control must always be
plumbed to the 120/230 volt solenoid valve supplied
with the Aqua Saver package.
AQUA SAVER MODULE
MODEL AS-3
460V, 1 or 3 phase
AQUA SAVER MODULE
MODEL AS-2
230V, 1 or 3 phase
AQUA SAVER MODULE
MODEL AS-1
120V, 1 or 3 phase
  • Page 1 1
  • Page 2 2

In-Sink-Erator AS-2 User manual

In-Sink-Erator
Brand
In-Sink-Erator
Model
AS-2
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents