Dell Brocade 5100 User guide

53-1002999-01

9 September 2013

®

Flow Vision

Administrator’s Guide

Supporting Fabric OS v7.2.0

ADX, AnyIO, Brocade, Brocade Assurance, the B-wing symbol, DCX, Fabric OS, ICX, MLX, MyBrocade, OpenScript, VCS, VDX, and

Vyatta are registered trademarks, and HyperEdge, The Effortless Network, and The On-Demand Data Center are trademarks of

Brocade Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names

mentioned may be trademarks of their respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning

any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to

this document at any time, without notice, and assumes no responsibility for its use. This informational document describes

features that may not be currently available. Contact a Brocade sales office for information on feature and product availability.

Export of technical data contained in this document may require an export license from the United States government.

The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with

respect to any loss, cost, liability, or damages arising from the information contained in this book or the computer programs that

accompany it.

The product described by this document may contain “open source” software covered by the GNU General Public License or other

open source license agreements. To find out which open source software is included in Brocade products, view the licensing

terms applicable to the open source software, and obtain a copy of the programming source code, please visit

http://www.brocade.com/support/oscd.

Brocade Communications Systems, Incorporated

Document History

Corporate and Latin American Headquarters

Brocade Communications Systems, Inc.

130 Holger Way

San Jose, CA 95134

Tel: 1-408-333-8000

Fax: 1-408-333-8101

E-mail: info@brocade.com

Asia-Pacific Headquarters

Brocade Communications Systems China HK, Ltd.

No. 1 Guanghua Road

Chao Yang District

Units 2718 and 2818

Beijing 100020, China

Tel: +8610 6588 8888

Fax: +8610 6588 9999

E-mail: china-info@brocade.com

European Headquarters

Brocade Communications Switzerland Sàrl

Centre Swissair

Tour B - 4ème étage

29, Route de l'Aéroport

Case Postale 105

CH-1215 Genève 15

Switzerland

Tel: +41 22 799 5640

Fax: +41 22 799 5641

E-mail: emea-info@brocade.com

Asia-Pacific Headquarters

Brocade Communications Systems Co., Ltd. (Shenzhen WFOE)

Citic Plaza

No. 233 Tian He Road North

Unit 1308 – 13th Floor

Guangzhou, China

Tel: +8620 3891 2000

Fax: +8620 3891 2111

E-mail: china-info@brocade.com

Title Publication number Summary of changes Date

Flow Vision Administrator’s Guide 53-1002999-01 FIrst release September 2013

Flow Vision Administrator’s Guide iii

53-1002999-01

Contents

About This Document

In this chapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Supported hardware and software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Text formatting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Command syntax conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Notes, cautions, and warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Key terms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Brocade Flow Vision terminology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Additional information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Brocade resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Other industry resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi

Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi

Document feedback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

Chapter 1 Flow Vision

In this chapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Overview of Flow Vision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Flow Vision features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Flow Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Flow Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Flow Mirror. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Flow definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Flow definition rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Supported port configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Flow frametype parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Numbers of flows supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Flow learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Viewing flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Flow Vision references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Roles and access in Flow Vision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Flow Vision integration with MAPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Flow Vision licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Flow Vision configuration setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Firmware upgrading and downgrading and Flow Vision. . . . . . . . . . . . 7

High Availability and Flow Vision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

iv Flow Vision Administrator’s Guide

53-1002999-01

Chapter 2 Flow Monitor

In this chapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Overview of Flow Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Flow Monitor management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Creating Flow Monitor flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Activating Flow Monitor flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Deactivating Flow Monitor flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Viewing Flow Monitor flows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Learning in Flow Monitor flows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Deleting Flow Monitor flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Resetting Flow Monitor flow statistics . . . . . . . . . . . . . . . . . . . . . . . . . .13

Flow Monitor examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Monitoring LUN level statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Viewing summary flow data for a specific device pair . . . . . . . . . . . . .14

Monitoring flows using the learning functionality . . . . . . . . . . . . . . . . .14

End-to-end monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Frame monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Ingress or egress Top Talker monitor. . . . . . . . . . . . . . . . . . . . . . . . . . .17

Configuring Flow Monitor for a trunk group . . . . . . . . . . . . . . . . . . . . 18

Monitoring Fibre Channel routed fabrics . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Monitoring FC router fabrics using port WWNs. . . . . . . . . . . . . . . . . . .19

Monitoring FC router fabrics using proxy IDs. . . . . . . . . . . . . . . . . . . . .24

Flow Monitor references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Flow monitors and MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Flow monitors on Access Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Flow Monitor and High Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Flow Monitor limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Chapter 3 Flow Generator

In this chapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Overview of Flow Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Flow Generator setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Flow Generator management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Creating Flow Generator flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Activating Flow Generator flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Learning in Flow Generator flows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Viewing Flow Generator flows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Deactivating Flow Generator flows . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Deleting Flow Generator flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Resetting Flow Generator flow statistics . . . . . . . . . . . . . . . . . . . . . . . .37

Customizing Flow Generator flows. . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Flow Generator examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Creating a flow from a specific Source ID to a specific Destination ID . .

38

Integrating Flow Generator with Flow Monitor . . . . . . . . . . . . . . . . . . .39

Flow Generator references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Commands related to Flow Generator. . . . . . . . . . . . . . . . . . . . . . . . . .40

Flow Vision Administrator’s Guide v

53-1002999-01

SIM-Port attributes and configuration . . . . . . . . . . . . . . . . . . . . . . . . . .41

Sending traffic using a Fabric Assigned WWN . . . . . . . . . . . . . . . . . . .42

Flow Generator and MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Flow Generator and High Availability . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Flow Generator limitations and considerations . . . . . . . . . . . . . . . . . .43

Chapter 4 Flow Mirror

In this chapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Overview of Flow Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Flow Mirror management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Creating Flow Mirror flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Activating Flow Mirror flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Viewing Flow Mirror flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Learning in Flow Mirror flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Deactivating Flow Mirror flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Deleting Flow Mirror flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Resetting Flow Mirror flow statistics . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Customizing Flow Mirror flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Troubleshooting using Flow Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Using Flow Mirror to diagnose SCSI reserve and SCSI release

performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Using Flow Mirror to troubleshoot protocol errors. . . . . . . . . . . . . . . . .53

Using Flow Mirror to diagnose a slow-draining F_Port . . . . . . . . . . . . .53

Flow Mirror references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Flow Mirror and High Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Flow Mirror limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Index

vi Flow Vision Administrator’s Guide

53-1002999-01

Flow Vision Administrator’s Guide vii

53-1002999-01

About This Document

In this chapter

•Supported hardware and software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

•Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

•Brocade Flow Vision terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

•Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

•Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

•Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

•Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

Supported hardware and software

In those instances in which procedures or parts of procedures documented here apply to some

switches but not to others, this guide identifies exactly which switches are supported and which are

not.

Although many different software and hardware configurations are tested and supported by

Brocade Communications Systems, Inc. for Fabric OS v7.2.0, documenting all possible

configurations and scenarios is beyond the scope of this document.

The following hardware platforms are supported by this release of Fabric OS:

• Fixed-port switches:

- Brocade 300 switch

- Brocade 5100 switch

- Brocade 5300 switch

- Brocade 5410 embedded switch

- Brocade 5424 embedded switch

- Brocade 5430 embedded switch

- Brocade 5431 embedded switch

- Brocade 5450 embedded switch

- Brocade 5460 embedded switch

- Brocade 5470 embedded switch

- Brocade 5480 embedded switch

- Brocade M6505 embedded switch

- Brocade 6505 switch

- Brocade 6510 switch

viii Flow Vision Administrator’s Guide

53-1002999-01

- Brocade 6520 switch

- Brocade 6547 embedded switch

- Brocade 7800 extension switch

- Brocade VA-40FC

- Brocade Encryption Switch

• Brocade DCX Backbone family:

- Brocade DCX

- Brocade DCX-4S

• Brocade DCX 8510 Backbone family:

- Brocade DCX 8510-4

- Brocade DCX 8510-8

• Brocade blades:

- Brocade FC8-32E

- Brocade FC8-48E

Document conventions

This section describes text formatting conventions and important notice formats used in this

document.

Text formatting

The narrative-text formatting conventions that are used are as follows:

bold text Identifies command names

Identifies the names of user-manipulated GUI elements

Identifies keywords and operands

Identifies text to enter at the GUI or CLI

italic text Provides emphasis

Identifies variables

Identifies paths and Internet addresses

Identifies document titles

code text Identifies CLI output

Identifies command syntax examples

For readability, command names in the narrative portions of this guide are presented in mixed

lettercase: for example, switchShow. In actual examples, command lettercase is often all

lowercase. Otherwise, this manual specifically notes those cases in which a command is

case-sensitive.

Flow Vision Administrator’s Guide ix

53-1002999-01

Command syntax conventions

Command syntax in this manual follows these conventions:

Notes, cautions, and warnings

The following notices and statements are used in this manual. They are listed below in order of

increasing severity of potential hazards.

NOTE

A Note provides a tip, guidance, or advice, emphasizes important information, or provides a

reference to related information.

ATTENTION

An Attention statement indicates potential damage to hardware or data.

CAUTION

A Caution statement alerts you to situations that can be potentially hazardous to you or cause

damage to hardware, firmware, software, or data.

DANGER

A Danger statement indicates conditions or situations that can be potentially lethal or extremely

hazardous to you. Safety labels are also attached directly to products to warn of these conditions

or situations.

Key terms

For definitions specific to Brocade and Fibre Channel, see the Brocade Glossary.

For definitions of SAN-specific terms, visit the Storage Networking Industry Association online

dictionary at:

http://www.snia.org/education/dictionary

command Commands are in bold.

--option, option Command options are in bold.

-argument, arg Arguments.

[ ] Optional element.

variable Variables are in italics.

... Repeat the previous element, for example “member[;member...]”

value Fixed values following arguments are in plain font. For example, --show WWN

| Boolean. Elements are exclusive. Example: --show

-mode egress | ingress

x Flow Vision Administrator’s Guide

53-1002999-01

Brocade Flow Vision terminology

The following terms are used in this document.

Notice to the reader

This document may contain references to the trademarks of the following corporations. These

trademarks are the properties of their respective companies and corporations.

These references are made for informational purposes only.

Additional information

This section lists additional Brocade and industry-specific documentation that you might find

helpful.

Brocade resources

To get up-to-the-minute information, go to http://my.brocade.com and register at no cost for a user

ID and password.

Term Description

Defined flow User-created flow; it can be active or inactive.

Local flow Flow defined on the switch on which the flow command is being run.

Root flow Instance of a static flow used to create learned flows.

Static flow Flow created when learning is not used.

Sub-flow System auto-created flow based on a root flow. There can be more than one sub-flow.

Remote flow Flow defined on a different switch from the one on which you are viewing it.

Local switch Switch on which the flow command is being run.

Remote switch Switch other than the switch on which the flow command is being run.

Corporation Referenced Trademarks and Products

Microsoft Corporation Windows, Windows NT, Internet Explorer

Mozilla Corporation Mozilla, Firefox

Netscape Communications Corporation Netscape

Red Hat, Inc. Red Hat, Red Hat Network, Maximum RPM, Linux Undercover

Oracle, Inc. Sun, Solaris, Oracle, Java

Flow Vision Administrator’s Guide xi

53-1002999-01

White papers, online demonstrations, and data sheets are available through the Brocade website

at:

http://www.brocade.com/products-solutions/products/index.page

For additional Brocade documentation, visit the Brocade Info Center and click the Resource Library

location:

http://www.brocade.com

Release notes are available on the My Brocade website and are also bundled with the Fabric OS

firmware.

Other industry resources

For additional resource information, visit the Technical Committee T11 website. This website

provides interface standards for high-performance and mass storage applications for Fibre

Channel, storage management, and other applications:

http://www.t11.org

For information about the Fibre Channel industry, visit the Fibre Channel Industry Association

website:

http://www.fibrechannel.org

Getting technical help

Contact your switch support supplier for hardware, firmware, and software support, including

product repairs and part ordering. To expedite your call, have the following information available:

1. General Information

- Switch model

- Switch operating system version

- Error numbers and messages received

- supportSave command output

- Detailed description of the problem, including the switch or fabric behavior immediately

following the problem, and specific questions

- Description of any troubleshooting steps already performed and the results

- Serial console and Telnet session logs

- syslog message logs

2. Switch serial number

The switch serial number and corresponding bar code are provided on the serial number label,

as illustrated below.

'"!&'

FT00X0054E9

xii Flow Vision Administrator’s Guide

53-1002999-01

The serial number label is located as follows:

• Brocade 300, 5100, 5300, 6505, M6505, 6520, 6547, 7800, VA-40FC, and Brocade

Encryption Switch—On the switch ID pull-out tab located inside the chassis on the port side on

the left

• Brocade 5410, 5424, 5430, 5431, 5450, 5460, 5470, 5480—Serial number label attached to

the module

• Brocade 6510—On the pull-out tab on the front of the switch

• Brocade DCX and DCX 8510-8—On the bottom right on the port side of the chassis

• Brocade DCX-4S and DCX 8510-4—On the bottom right on the port side of the chassis, directly

above the cable management comb

3. World Wide Name (WWN)

Use the wwn command to display the switch WWN.

If you cannot use the wwn command because the switch is inoperable, you can get the WWN

from the same place as the serial number, except for the Brocade DCX Backbone family.

For the Brocade DCX Backbone family, access the numbers on the WWN cards by removing the

Brocade logo plate at the top of the nonport side of the chassis.

For the Brocade 5424 embedded switch, provide the license ID. Use the licenseIdShow

command to display the WWN.

Document feedback

Quality is our first concern at Brocade and we have made every effort to ensure the accuracy and

completeness of this document. However, if you find an error or an omission, or you think that a

topic needs further development, we want to hear from you. Forward your feedback to:

documentation@brocade.com

Provide the title and version number of the document and as much detail as possible about your

comment, including the topic heading and page number and your suggestions for improvement.

Flow Vision Administrator’s Guide 1

53-1002999-01

Chapter

1

Flow Vision

In this chapter

•Overview of Flow Vision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

•Flow Vision features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

•Flows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

•Flow Vision references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Overview of Flow Vision

Flow Vision is a Fibre-Channel SAN network diagnostic tool supported on all platforms supported by

Fabric OS 7.2 and later, that provides you with a comprehensive vision of fabric traffic flows and

with the ability to non-disruptively create and capture copies of traffic flows for later analysis.

Flow Vision also provides a test flow generation capability that you can use to pre-test a SAN

infrastructure for robustness. This test flow generation capability is also useful for testing the

internal connections on a switch before deploying the switch into a production environment.

You cannot run Flow Vision and Advanced Performance Monitor (APM), or Port Mirroring at the

same time on a chassis (across logical switches).

Flow Vision features

Flow Vision has three features: Flow Monitor, Flow Generator, and Flow Mirror. The following

sections describe each feature and provides a sample use case link.

Flow Monitor

Flow Monitor provides flow monitoring and the gathering of frame statistics for fabric application

flows, including the ability to learn (discover) flows automatically. See “Flow Monitor” on page 9 for

a complete description and sample use cases.

Flow Generator

Flow Generator simulates and generates test-load traffic in specific flows; this allows you to

validate hardware components, connectivity, and verify performance. See “Flow Generator” on

page 31 for a complete description and sample use cases.

Flow Mirror

Flow Mirror provides the ability to non-disruptively create copies of application flow frames that can

be captured for deeper analysis. See “Flow Mirror” on page 45 for a complete description and

sample use cases.

2 Flow Vision Administrator’s Guide

53-1002999-01

Flows

1

Flows

A flow is a set of Fibre Channel (FC) frames or packets that share similar traits, such as an ingress

port or egress port identifier or any other data that can be used to differentiate one set of related

frames or packets from a different set. These parameters are specified as part of the flow

command, and include:

• Port parameters: (also called the Point of Interest, or where the data you want to examine is

from) This consists of an ingress port (ingrport) or an egress port (egrport). Only one can be

specified when defining a flow.

• Frame parameters: These are the following parameters: Source Device Identification (SID or

WWN), Destination Device Identification (DID or WWN), LUN, or frame type. At least one frame

parameter must be present to define a flow. Refer to Table 3 on page 4 for details on frame types.

• Direction: A direction is implicitly defined from an ingress port to an egress port, or a source

device (srcdev) to a destination device (dstdev). For example, srcdev=x, dstdev=y indicates

traffic flowing from x to y. The -bidir option causes the flow definition to be monitored in both

directions. This makes the following true:

- Entering srcdev=x dstdev=y specifies that only traffic flowing from x to y is the desired flow.

- Entering srcdev=x dstdev=y -bidir specifies that traffic travelling from x to y and traffic

travelling from y to x are both desired flows.

Figure 1 illustrates how the frame and port parameters apply to a flow.

FIGURE 1 Frame and port parameters

Flow definitions

To define a flow and configure Flow Vision to monitor that flow, you must provide a unique flow

name and specify the flow parameters. These parameters identify the sets of related frames and

can either be explicitly defined or Flow Vision can learn them through observation.

Flow definitions are stored on the switch on which the flow is created, and are not distributed

across the fabric. This means that each switch knows only its own flows and does not know what

flows exist on other switches.

Flow Vision Administrator’s Guide 3

53-1002999-01

Flows

1

When creating or viewing a flow, you can specify any combination of the three features in the flow

command. For example:

flow --create flowname -feature monitor,generator <parameters>

flow --show flowname -feature mirror,generator <parameters>

Flow definition rules

The rules listed in Table 1 identify what parameters can be used to define a flow.

Supported port configurations

Table 2 lists the supported configurations for each Flow Vision feature using only the basic flow

identification parameters (ingrport and srcdev, egrport and dstdev).

If you are using at least one advanced parameter (lun, -frametype, or -bidir), then feature-specific

rules apply. Refer to the individual Flow Vision features for specific details.

NOTE

Neither ranges nor lists are supported for any parameter.

TABLE 1 Flow definition rules

Parameters Field names Rules

Port ingrport

egrport

• One field only must be specified

• Values must be explicit

Frame srcdev

dstdev

lun

frametype

1

1. Refer to Table 3 for more information on frame types.

• At least one field must be specified

• Values for srcdev and dstdev can be explicit or “*” (“*” indicates learned flows)

• Values for lun and frametype must be explicit

TABLE 2 Port configurations supported in Flow Vision

Feature Platforms Switch Configuration Mode

16 Gbps-capable

Fibre Channel

1

1. 16Gbps-capable platforms include the Brocade FC8-32E and FC8-48E blades.

8 Gbps-capable Fibre Channel Access Gateway Virtual Fabric

Flow Generator

Supported (SIM-Ports only) Supported

(Destination SIM-Ports only)

Not Supported Supported

Flow Mirror

Supported (F_Ports only) Not Supported Not Supported Supported

Flow Monitor

Supported (E_Ports.

EX_Ports, and F_Ports only)

Supported (F_Ports only) Supported

(F_Ports only)

Supported

4 Flow Vision Administrator’s Guide

53-1002999-01

Flows

1

Flow frametype parameters

Frame monitoring can be done for a variety of frames using predefined -frametype parameters.

Table 3 list these parameters and the frames counted for each.

On 8 Gbps-capable Fibre Channel platforms, possible frame monitoring flow classifiers include

egrport, dstdev, and lun. On 16 Gbps-capable Fibre Channel platforms, including the Brocade

FC8-32E and FC8-48E blades, possible frame monitoring flow classifiers include ingrport, egrport,

dstdev, srcdev, and lun.

TABLE 3 Supported frametype parameters

Frametype parameter Frames counted

abts Abort Sequence

baacc All frames accepted

barjt All frames rejected

scsi All SCSI frames (including both command and data frames)

scsiread Only SCSI read command frames

scsiwrite Only SCSI write command frames

scsirw Both SCSI read and write command frames

scsi2reserve Only SCSI 2 reserve command frames

scsi3reserve Only SCSI 3 reserve command frames

scsi2release Only SCSI 2 release command frames

scsi3release Only SCSI 3 release command frames

scsi2reserverelease Only SCSI 2 reserve-release command frames

scsi3reserverelease Only SCSI 3 reserve-release command frames

scsitur Only SCSI test unit ready frames

scsistatus Only SCSI status frames

scsicmdsts

1

1. This parameter is valid only for Flow Mirror. It implicitly assumes -bidir and looks for both SCSI command and

status frames.

Only SCSI command status frames

scsigoodstatus Only SCSI status frames with status marked as good (all 0s (zeros) in status byte)

scsicheckstatus Only SCSI status frames with check status

(Check Condition, Busy, Reservation Conflict, Task Full Set)

scsiinquiry Only SCSI inquiry frames

scsiresvconflict Only SCSI status frames with reservation conflict set

scsixferrdy Only SCSI FCP XFER_RDY (transfer ready) frames

Flow Vision Administrator’s Guide 5

53-1002999-01

Flows

1

Numbers of flows supported

Flow Vision supports a maximum of 512 flows on chassis-based platforms and a maximum of

128 flows on fixed-port platforms. However, there is a combined limit from all features of 64 flows

(including static flows, root flows, and sub-flows, whether active or inactive) for any one port. In

addition, there are individual limits for each Flow Vision feature; Table 4 lists these limits.

A verification is done for each flow when it is created or activated to ensure that there is no

identical flow active. Refer to the limitations section of each feature for additional feature-specific

restrictions.

Flow learning

Flow Vision can create a learned flow by using an asterisk (*) for the source device, the destination

device, or both devices. This allows you to discover what flows are active on a port without having to

identify all the devices. Each Flow Vision feature uses learning as follows:

• Flow Monitor can learn all the source device and destination device pairs passing through the

ingress or egress port defined in a flow. Learning is not supported for Flow Monitor flows

defined using the lun, -frametype, or -bidir parameters. Refer to “Learning in Flow Monitor

flows” on page 12 for additional information.

• Flow Generator can generate traffic to or from every source or destination device that shares

the zone with the ingress or egress port defined in a flow. Refer to “Learning in Flow Generator

flows” on page 34 for additional information.

• Flow Mirror can capture all the source device and destination device pairs passing through the

ingress or egress port defined in a flow. Learning is supported for Flow Mirror flows defined

using the lun, -frametype, or -bidir parameters. Refer to “Learning in Flow Mirror flows” on

page 51 for additional information.

Flow Vision uses an asterisk (*) to indicate a learned flow. When you enter an asterisk as part of

the command, you must enclose it in double quotes (“*”).

Learning source device (srcdev) or destination device (dstdev) values is only supported on

16 Gbps-capable Fibre Channel ports.

Viewing flows

To display all Flow Vision flows, enter flow --show. To display all flows for a specific feature, enter

flow --show -feature featurename. To display the definition for a specific flow, enter flow --show

flowname -feature featurename. When you run flow --show with a flow name, then only the flow

definition for the specified flow is displayed. If the feature is also specified, feature-specific data is

displayed for the specified flow name. For root and static flows, this command shows the

Source ID-Destination ID pairs and the cumulative frame count on the ingress or egress port

specified in the flow definition.

TABLE 4 Feature-specific flow count restrictions in Flow Vision

Feature Limit to number of flows

Flow Monitor Up to 64 active flows per port, including static flows, root flows, and sub-flows.

Flow Generator Up to 4 active flows per port, including static flows, root flows, and sub-flows.

Flow Mirror One active flow per port.

6 Flow Vision Administrator’s Guide

53-1002999-01

Flow Vision references

1

The following example displays all the existing flows on the switch.

switch:admin> flow --show

------------------------------------------------------------------------------------------------

------------------------------------------------------------------------------------------------

local |gen |- |019200 |13 |- |no |- |- |

flow2 |gen+,mon+ |010900 |01c100 |1/9 |- |no |- |- |

flow1 |gen+,mon+ |01c100 |- |8/1 |- |no |- |- |

------------------------------------------------------------------------------------------------

+ Denotes feature is currently activated for the flow

Refer to the “viewing” section of each individual feature to see feature-specific output.

Flow Vision references

The following sections provide additional information about Flow Vision.

Roles and access in Flow Vision

Flow Vision can be accessed by users with the following roles: Admin, Switch Admin, or

Fabric Admin.

Flow Vision integration with MAPS

Statistics generated using Flow Vision can be monitored with the Monitoring and Alerting Policy

Suite (MAPS) threshold service. Refer to the MAPS section of each individual feature in this manual

for information on how that feature interacts with MAPS, and the Monitoring and Alerting Policy

Suite Administrator’s Guide for more details on MAPS in general.

Flow Vision licensing

To run Flow Vision, you need either the Fabric Vision (FV) license or both the Fabric Watch (FW) and

the Advanced Performance Monitor (APM) licenses. If you have both of these licenses, you do not

need a separate Flow Vision license. Refer to the Fabric OS Administrator’s Guide for more specific

information on licenses.

Flow Vision configuration setup

The Flow Vision configuration can be saved through the configdownload command and uploaded

through the configupload command. The configdefault command deletes all flows and simulation

ports (SIM-Ports) from the switch.

When a switch goes offline or comes online, Flow Vision reads the configuration files and then

deletes flows, creates flows, and activates flows. After a switch goes offline, any flows that were

active at the time it went offline will be reactivated when it comes back online and new traffic will

be generated as soon as the source and destination devices defined in the flow are online.

NOTE

Statistical data for flows is not saved in the configuration database.

Flow Vision Administrator’s Guide 7

53-1002999-01

Flow Vision references

1

Firmware upgrading and downgrading and Flow Vision

There are no restrictions on upgrading the firmware of a switch that has Flow Vision installed.

Downgrading the firmware on a switch with Flow Vision installed will fail if any Flow Vision-related

configurations are present on the switch being downgraded. All Flow Vision-related flows or

simulation ports must be deleted prior to performing a downgrade to any version of Fabric OS prior

to version 7.2.0; if they are not, the downgrade will be blocked and a warning message displayed.

High Availability and Flow Vision

If a standby Command Processor (CP) with a down rev code comes online and any flows (active or

non-active) are configured, the HA will be out of sync. If a standby Command Processor (CP) with a

down rev code comes online and no flows (active or non-active) are configured, HA will be in sync

but flow creation will fail.

High Availability (HA) preserves only the Flow Vision configuration settings through an HA failover,

HA reboot, or a power cycle and reboot. It does not save feature-related data (for example,

statistics).

Refer to the individual feature’s HA section for information on how that feature is treated under HA:

• “Flow Monitor and High Availability” on page 29

• “Flow Generator and High Availability” on page 43

• “Flow Mirror and High Availability” on page 55

NOTE

While disabling a SIM-Port that is receiving traffic may produce class 3 discards for the simulated

traffic, this will have no effect on other traffic flows.

8 Flow Vision Administrator’s Guide

53-1002999-01

Flow Vision references

1

Page is loading ...

Dell Brocade 5100 User guide

Dell Brocade 5100 User guide

Related papers

Other documents