Dell Brocade M6505 User guide

53-1002933-02

9 September 2013

®

Monitoring and Alerting

Policy Suite

Administrator’s Guide

Supporting Fabric OS v7.2.0a

ADX, AnyIO, Brocade, Brocade Assurance, the B-wing symbol, DCX, Fabric OS, ICX, MLX, MyBrocade, OpenScript, VCS, VDX, and

Vyatta are registered trademarks, and HyperEdge, The Effortless Network, and The On-Demand Data Center are trademarks of

Brocade Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names

mentioned may be trademarks of their respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning

any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to

this document at any time, without notice, and assumes no responsibility for its use. This informational document describes

features that may not be currently available. Contact a Brocade sales office for information on feature and product availability.

Export of technical data contained in this document may require an export license from the United States government.

The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with

respect to any loss, cost, liability, or damages arising from the information contained in this book or the computer programs that

accompany it.

The product described by this document may contain “open source” software covered by the GNU General Public License or other

open source license agreements. To find out which open source software is included in Brocade products, view the licensing

terms applicable to the open source software, and obtain a copy of the programming source code, please visit

http://www.brocade.com/support/oscd.

Brocade Communications Systems, Incorporated

Document History

Corporate and Latin American Headquarters

Brocade Communications Systems, Inc.

130 Holger Way

San Jose, CA 95134

Tel: 1-408-333-8000

Fax: 1-408-333-8101

E-mail: info@brocade.com

Asia-Pacific Headquarters

Brocade Communications Systems China HK, Ltd.

No. 1 Guanghua Road

Chao Yang District

Units 2718 and 2818

Beijing 100020, China

Tel: +8610 6588 8888

Fax: +8610 6588 9999

E-mail: china-info@brocade.com

European Headquarters

Brocade Communications Switzerland Sàrl

Centre Swissair

Tour B - 4ème étage

29, Route de l'Aéroport

Case Postale 105

CH-1215 Genève 15

Switzerland

Tel: +41 22 799 5640

Fax: +41 22 799 5641

E-mail: emea-info@brocade.com

Asia-Pacific Headquarters

Brocade Communications Systems Co., Ltd. (Shenzhen WFOE)

Citic Plaza

No. 233 Tian He Road North

Unit 1308 – 13th Floor

Guangzhou, China

Tel: +8620 3891 2000

Fax: +8620 3891 2111

E-mail: china-info@brocade.com

Title Publication number Summary of changes Date

Monitoring and Alerting Policy Suite

Administrator’s Guide

53-1002933-01 First release July 2013

Monitoring and Alerting Policy Suite

Administrator’s Guide

53-1002933-02 Updated to match FOS 7.2.0a September 2013

Monitoring and Alerting Policy Suite Administrator’s Guide iii

53-1002933-02

Contents

About This Document

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Supported hardware and software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Document conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Text formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Command syntax conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Notes, cautions, and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Key terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Brocade resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Other industry resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

Chapter 1 Monitoring and Alerting Policy Suite Overview

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

MAPS overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

MAPS license requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAPS interoperability with other features. . . . . . . . . . . . . . . . . . . . . . . . . 2

MAPS and Virtual Fabrics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAPS and Fabric Watch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAPS configuration files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAPS and High Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAPS and Admin Domains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAPS upgrade and downgrade considerations . . . . . . . . . . . . . . . . . . . . 3

Migrating from Fabric Watch to MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Differences between Fabric Watch and MAPS configurations . . . . . 4

MAPS and Flow Vision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2 Enabling and Configuring MAPS

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Enabling MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

MAPS configuration quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

iv Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

MAPS configuration tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Monitoring a new port using existing rules . . . . . . . . . . . . . . . . . . . . 9

Monitoring across different time windows . . . . . . . . . . . . . . . . . . . . . 9

Resetting MAPS configuration upload and download to Brocade

defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Chapter 3 MAPS Elements and Categories

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

MAPS structural elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

MAPS monitoring categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Switch Policy Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Port Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

FRU Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Security Violations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Fabric State Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Switch Resource . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Traffic Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

FCIP Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 4 MAPS Groups, Policies, Rules, and Actions

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

MAPS groups overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Predefined groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

User-defined groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Viewing group information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Monitoring similar ports using the same rules . . . . . . . . . . . . . . . . 22

MAPS policies overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Predefined policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

User-defined policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Fabric Watch legacy policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Working with MAPS policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Viewing policy information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Creating a policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Enabling a policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Modifying a policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Modifying a default policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

MAPS rules overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

MAPS conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Time base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Monitoring and Alerting Policy Suite Administrator’s Guide v

53-1002933-02

MAPS actions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Enabling or disabling actions at a global level. . . . . . . . . . . . . . . . . 28

RASLog messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

SNMP traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

E-mail alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Port fencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Switch critical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Switch marginal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

SFP marginal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Working with MAPS rules and actions . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Creating a rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Modifying a rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Cloning a rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Sending alerts using e-mail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Chapter 5 Monitoring flows using MAPS

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Flows and MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Importing flows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Removing flows from MAPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Monitoring flows using MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

If an imported flow is deleted in Flow Vision . . . . . . . . . . . . . . . . . . 36

Examples of using MAPS to monitor traffic performance . . . . . . . . 37

Chapter 6 MAPS Dashboard

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

MAPS dashboard overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

MAPS dashboard sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Historical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

MAPS dashboard display options . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Viewing the MAPS dashboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Clearing data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Bottleneck detection integration with the MAPS dashboard . . . . . . . . . 47

Additional information about bottleneck detection . . . . . . . . . . . . . 47

Dashboard output for bottleneck data . . . . . . . . . . . . . . . . . . . . . . . 48

Flow Vision integration with the MAPS dashboard . . . . . . . . . . . . . . . . . 48

Chapter 7 Additional MAPS features

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Pausing and resuming MAPS monitoring . . . . . . . . . . . . . . . . . . . . . . . . 49

MAPS Service Availability Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Appendix A MAPS Threshold values

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

vi Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

MAPS threshold value tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Index

Monitoring and Alerting Policy Suite Administrator’s Guide vii

53-1002933-02

About This Document

In this chapter

•Supported hardware and software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

•Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

•Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

•Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

•Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

•Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

Supported hardware and software

In those instances in which procedures or parts of procedures documented here apply to some

switches but not to others, this guide identifies exactly which switches are supported and which are

not.

Although many different software and hardware configurations are tested and supported by

Brocade Communications Systems, Inc. for Fabric OS v7.2.0a, documenting all possible

configurations and scenarios is beyond the scope of this document.

The following hardware platforms are supported by this release of Fabric OS:

• Fixed-port switches:

- Brocade 300 switch

- Brocade 5100 switch

- Brocade 5300 switch

- Brocade 5410 embedded switch

- Brocade 5424 embedded switch

- Brocade 5430 embedded switch

- Brocade 5431 embedded switch

- Brocade 5450 embedded switch

- Brocade 5460 embedded switch

- Brocade 5470 embedded switch

- Brocade 5480 embedded switch

- Brocade M6505 embedded switch

- Brocade 6505 switch

- Brocade 6510 switch

- Brocade 6520 switch

viii Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

- Brocade 6547 embedded switch

- Brocade 7800 extension switch

- Brocade VA-40FC

- Brocade Encryption Switch

• Brocade DCX Backbone family:

- Brocade DCX

- Brocade DCX-4S

• Brocade DCX 8510 Backbone family:

- Brocade DCX 8510-4

- Brocade DCX 8510-8

Document conventions

This section describes text formatting conventions and important notice formats used in this

document.

Text formatting

The narrative-text formatting conventions that are used are as follows:

bold text Identifies command names

Identifies the names of user-manipulated GUI elements

Identifies keywords and operands

Identifies text to enter at the GUI or CLI

italic text Provides emphasis

Identifies variables

Identifies paths and Internet addresses

Identifies document titles

code text Identifies CLI output

Identifies command syntax examples

For readability, command names in the narrative portions of this guide are presented in mixed

lettercase: for example, switchShow. In actual examples, command lettercase is often all

lowercase. Otherwise, this manual specifically notes those cases in which a command is

case-sensitive.

Command syntax conventions

Command syntax in this manual follows these conventions:

command Commands are in bold.

--option, option Command options are in bold.

-argument, arg Arguments are in bold.

[ ] Optional element.

Monitoring and Alerting Policy Suite Administrator’s Guide ix

53-1002933-02

Notes, cautions, and warnings

The following notices and statements are used in this manual. They are listed below in order of

increasing severity of potential hazards.

NOTE

A note provides a tip, guidance. or advice, emphasizes important information, or provides a

reference to related information.

ATTENTION

An Attention statement indicates potential damage to hardware or data.

CAUTION

A Caution statement alerts you to situations that can be potentially hazardous to you or cause

damage to hardware, firmware, software, or data.

DANGER

A Danger statement indicates conditions or situations that can be potentially lethal or extremely

hazardous to you. Safety labels are also attached directly to products to warn of these conditions

or situations.

Key terms

For definitions specific to Brocade and Fibre Channel, refer to the Brocade Glossary.

For definitions of SAN-specific terms, visit the Storage Networking Industry Association online

dictionary at:

http://www.snia.org/education/dictionary

variable Variables are in italics.

... Repeat the previous element, for example “member[;member...]”

value Fixed values following arguments are in plain font. For example,

--show WWN

| Boolean. Elements are exclusive. Example:

--show -mode egress | ingress

x Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

Notice to the reader

This document may contain references to the trademarks of the following corporations. These

trademarks are the properties of their respective companies and corporations.

These references are made for informational purposes only.

Additional information

This section lists additional Brocade and industry-specific documentation that you might find

helpful.

Brocade resources

To get up-to-the-minute information, go to http://my.brocade.com and register at no cost for a user

ID and password.

For additional Brocade documentation, visit the Brocade SAN Info Center and click the Resource

Library location:

http://www.brocade.com

Release notes are available on the My Brocade website and are also bundled with the Fabric OS

firmware.

Other industry resources

For additional resource information, visit the Technical Committee T11 website. This website

provides interface standards for high-performance and mass storage applications for Fibre

Channel, storage management, and other applications:

http://www.t11.org

For information about the Fibre Channel industry, visit the Fibre Channel Industry Association

website:

http://www.fibrechannel.org

Corporation Referenced Trademarks and Products

Microsoft Corporation Windows, Windows NT, Internet Explorer

Mozilla Corporation Mozilla, Firefox

Netscape Communications Corporation Netscape

Red Hat, Inc. Red Hat, Red Hat Network, Maximum RPM, Linux Undercover

Oracle, Inc. Sun, Solaris, Oracle, Java

Monitoring and Alerting Policy Suite Administrator’s Guide xi

53-1002933-02

Getting technical help

Contact your switch support supplier for hardware, firmware, and software support, including

product repairs and part ordering. To expedite your call, have the following information available:

1. General Information

• Switch model

• Switch operating system version

• Error numbers and messages received

• supportSave command output

• Detailed description of the problem, including the switch or fabric behavior immediately

following the problem, and specific questions

• Description of any troubleshooting steps already performed and the results

• Serial console and Telnet session logs

• syslog message logs

2. Switch serial number

The switch serial number and corresponding bar code are provided on the serial number label,

as illustrated below:

The serial number label is located as follows:

• Brocade 300, 5100, 5300, 6505, M6505, 6510, 6520, 6547, 7800, VA-40FC, and Brocade

Encryption Switch—On the switch ID pull-out tab located inside the chassis on the port side on

the left

• Brocade 5410, 5424, 5430, 5431, 5450, 5460, 5470, 5480—Serial number label attached to

the module

• Brocade 6510—On the pull-out tab on the front of the switch

• Brocade DCX and DCX 8510-8—On the bottom right on the port side of the chassis

• Brocade DCX-4S and DCX 8510-4—On the bottom right on the port side of the chassis, directly

above the cable management comb

3. World Wide Name (WWN)

Use the wwn command to display the switch WWN.

If you cannot use the wwn command because the switch is inoperable, you can get the WWN

from the same place as the serial number, except for the Brocade DCX enterprise class

platform. For the Brocade DCX enterprise class platform, access the numbers on the WWN

cards by removing the Brocade logo plate at the top of the nonport side of the chassis.

For the Brocade 5424 embedded switch: Provide the license ID. Use the licenseIdShow

command to display the WWN.

'"!&'

FT00X0054E9

xii Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

Document feedback

Quality is our first concern at Brocade and we have made every effort to ensure the accuracy and

completeness of this document. However, if you find an error or an omission, or you think that a

topic needs further development, we want to hear from you. Forward your feedback to:

documentation@brocade.com

Provide the title and version number of the document and as much detail as possible about your

comment, including the topic heading and page number and your suggestions for improvement.

Monitoring and Alerting Policy Suite Administrator’s Guide 1

53-1002933-02

Chapter

1

Monitoring and Alerting Policy Suite Overview

In this chapter

•MAPS overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

•MAPS license requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

•MAPS interoperability with other features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

•MAPS upgrade and downgrade considerations . . . . . . . . . . . . . . . . . . . . . . . 3

•Migrating from Fabric Watch to MAPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

•MAPS and Flow Vision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

MAPS overview

The Monitoring and Alerting Policy Suite (MAPS) is an optional storage area network (SAN) health

monitor supported on all switches running Fabric OS 7.2.0 or later that allows you to enable each

switch to constantly monitor itself for potential faults and automatically alerts you to problems

before they become costly failures.

MAPS tracks a variety of SAN fabric metrics and events. Monitoring fabric-wide events, ports, and

environmental parameters enables early fault detection and isolation as well as performance

measurements.

MAPS provides a set of pre-defined monitoring policies that allow you to immediately use MAPS on

activation. Refer to “Predefined policies” for more information on using these policies.

In addition, MAPS provides customizable monitoring thresholds. These allow you to configure

specific groups of ports or other elements so that they share a common threshold value. You can

configure MAPS to provide notifications before problems arise, for example, when network traffic

through a port is approaching the bandwidth limit. MAPS lets you define how often to check each

switch and fabric measure and specify notification thresholds. Whenever fabric measures exceed

these thresholds, MAPS automatically provides notification using several methods, including e-mail

messages, SNMP traps, and log entries. Refer to “MAPS Groups, Policies, Rules, and Actions” for

more information on using these features.

The MAPS dashboard provides you with the ability to view in a quick glance what is happening on

the switch, and helps administrators dig deeper to see details of exactly what is happening on the

switch (for example, the kinds of errors, the error count, and so on.) Refer to “MAPS dashboard

overview” for more information.

MAPS provides a seamless migration of all customized Fabric Watch thresholds to MAPS, thus

allowing you to take advantage of the advanced capabilities of MAPS. MAPS provides additional

advanced monitoring, such as monitoring for the same error counters across different time

periods, or having more than two thresholds for any error counters. MAPS also provides support for

you to monitor the statistics provided by the Flow Monitor feature of Flow Vision.

Refer to “Differences between Fabric Watch and MAPS configurations” and “Migrating from

Fabric Watch to MAPS” for details.

2 Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

MAPS license requirements

1

MAPS license requirements

MAPS is an optionally licensed feature of Fabric OS. MAPS requires an active and valid

Fabric Vision license. If you already have a license for Fabric Watch plus a license for Advanced

Performance Monitoring, you will automatically get MAPS functionality without having to obtain an

additional license.

MAPS interoperability with other features

MAPS interacts in different ways with different Fabric OS features, including Virtual Fabrics,

Fabric Watch, High Availability, and Admin Domains.

MAPS and Virtual Fabrics

When using virtual fabrics, different logical switches in a chassis can have different MAPS

configurations.

MAPS and Fabric Watch

MAPS cannot coexist with Fabric Watch. For information about migrating from Fabric Watch to

MAPS, refer to “Migrating from Fabric Watch to MAPS” on page 3.

MAPS configuration files

The MAPS configuration is stored in two separate configuration files, one for the default MAPS

configuration and one for the user-created MAPS configuration. Only one user configuration file can

exist for each logical switch. A configuration upload or download affects only the user-created

configuration files. You cannot upload or download the default MAPS configuration file. To remove

the user-created MAPS configuration run mapsConfig --purge. For more information on this

command, refer to the Fabric OS Command Reference.

MAPS and High Availability

MAPS configuration settings are maintained across a HA failover or HA reboot; however, MAPS will

restart monitoring after a HA failover or reboot and the MAPS cached statistics are not retained.

MAPS and Admin Domains

MAPS is supported on switches that have Admin Domains. There can only be one MAPS

configuration that is common to all the Admin Domains on the chassis. Users with Administrator

privileges can modify the MAPS configuration from any Admin Domain.

ATTENTION

If MAPS is enabled, do not download configuration files that have Admin Domains defined.

Monitoring and Alerting Policy Suite Administrator’s Guide 3

53-1002933-02

MAPS upgrade and downgrade considerations

1

MAPS upgrade and downgrade considerations

When downgrading from Fabric OS 7.2 to any previous version of the OS, the following

MAPS-related behaviors should be expected:

• When an active CP is running Fabric OS 7.2 with MAPS disabled, and the standby device has

an earlier version of the Fabric OS, High Availability will be synchronized, but MAPS will not be

allowed to be enabled until the firmware on the standby device is upgraded. The

mapsConfig --enablemaps command fails and an error message is displayed.

• When an active CP is running Fabric OS 7.2 and MAPS is enabled, but the standby device is

running Fabric OS 7.1 or earlier, then High Availability will not be synchronized until the standby

CP is upgraded to Fabric OS 7.2.

• On devices with a single CP, there is no change in behavior when downgrading to an earlier

version of the Fabric OS.

• When a configuration download occurs, the MAPS configuration is downloaded onto a switch

only if MAPS is enabled on that local switch.

Migrating from Fabric Watch to MAPS

To use MAPS, you must migrate from Fabric Watch to MAPS. On a switch running Fabric OS 7.2.0 or

later, or when you upgrade your existing switch to Fabric OS 7.2.0, Fabric Watch is enabled by

default. On an upgraded switch, Fabric Watch continues to monitor as in Fabric OS 7.1.0 until

MAPS is activated.

When you migrate from Fabric Watch to MAPS, the Fabric Watch configuration can be converted to

a MAPS-compatible configuration so you do not need to reconfigure all of the thresholds and rules.

If you do not make the conversion as part of the migration, you will need to configure the rules

manually.

Activating MAPS is a chassis-specific process, and you can activate only one chassis at a time. On a

given chassis there can be multiple logical switches. Activating MAPS will enable it for all logical

switches in the chassis. Each logical switch can have its own MAPS configuration.

To migrate from Fabric Watch and activate MAPS, run the following commands:

mapsconfig --enablemaps

followed by

mapsconfig --fwconvert -enablepolicy policyname

Upon successful completion of this command, the following happens:

• Fabric Watch configurations are converted to MAPS policies. Refer to “Fabric Watch legacy

policies” on page 23 for additional information.

To not convert the Fabric Watch configurations when you activate MAPS, do not include

--fwconvert in the command.

• Fabric Watch monitoring and commands are disabled.

• MAPS commands are enabled.

• The MAPS policy that is specified in the -enablepolicy policy parameter is enabled.

4 Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

Migrating from Fabric Watch to MAPS

1

CAUTION

MAPS activation is a non-reversible process. Downgrading to Fabric OS 7.1 will enable Fabric

Watch with its last configured settings. When you upgrade back to Fabric OS 7.2, Fabric Watch

will continue to be enabled.

Differences between Fabric Watch and MAPS configurations

The MAPS monitoring and alerting configurations are not as complex as those available in

Fabric Watch; consequently MAPS does not have some functionality that was available in

Fabric Watch.

Table 1 shows differences between Fabric Watch and MAPS configurations.

TABLE 1 Differences between Fabric Watch and MAPS configurations

Configuration Fabric Watch behavior MAPS behavior

End-to-End monitoring

(Performance Monitor class)

Supported. Supported through flows. Refer to

“Monitoring end-to-end performance”

on page 37 for details.

Frame monitoring

(Performance Monitor class)

Supported. Supported through flows. Refer to

“Monitoring frames for a specified set

of criteria” on page 37 for details.

RX, TX monitoring Occurs at the individual physical port

level.

Occurs at the trunk or port level as

applicable.

Pause/Continue behavior Occurs at the element or counter level.

For example, monitoring can be paused

for CRC on one port and for ITW on

another port.

Occurs at the element level.

Monitoring can be paused on a

specific port, but not for a specific

counter on that port.

CPU/Memory polling interval Can configure the polling interval as well

as the repeat count.

This configuration can be migrated

from Fabric Watch, but cannot be

changed.

E-mail notification

configuration

Different e-mail addresses can be

configured for different classes.

E-mail configuration supported

globally.

Temperature sensor

monitoring

Can monitor temperature values. Can monitor only the states of the

sensors (In_Range or Out_of_range).

Monitoring and Alerting Policy Suite Administrator’s Guide 5

53-1002933-02

MAPS and Flow Vision

1

MAPS and Flow Vision

MAPS can work with information generated by the Brocade Flow Vision application. For more

information, refer to “Flow Vision integration with the MAPS dashboard” on page 48, and the

Fabric OS Flow Vision Administrator’s Guide.

MAPS supports only the following statistics generated by Flow Vision flow monitors.

• Frame statistics:

• Number of frames transmitted from the flow source

• Number of frames received by the flow destination

• Number of megabytes (MB) transmitted per second by the flow source

• Number of megabytes (MB) received per second by the flow destination

• SCSI statistics:

• Number of SCSI I/O read command frames recorded for the flow

• Number of SCSI I/O write command frames recorded for the flow

• Number of SCSI I/O bytes read as recorded for the flow

• Number of SCSI I/O bytes written as recorded for the flow

6 Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

MAPS and Flow Vision

1

Monitoring and Alerting Policy Suite Administrator’s Guide 7

53-1002933-02

Chapter

2

Enabling and Configuring MAPS

In this chapter

•Enabling MAPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

•MAPS configuration quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

•MAPS configuration tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Enabling MAPS

MAPS is not enabled by default. To enable MAPS, enter the following command:

mapsConfig --enableMaps -policy policyname

You must supply a named policy to enable MAPS.

Once you have converted the Fabric Watch rules for use in MAPS (this must be done first), you can

enable and configure MAPS. Refer to “MAPS configuration quick start” on page 7 and “Migrating

from Fabric Watch to MAPS” on page 3 for more information on making the migration and getting

started with MAPS.

MAPS configuration quick start

You can quickly start monitoring your switch using one of the predefined policies. Alternatively, if

you are already using Fabric Watch and would like MAPS to use the same thresholds, convert the

Fabric Watch policies into MAPS policies and then enable MAPS using the policy named

“fw_active_policy”. This provides the same monitoring functionality as Fabric Watch. Refer to

“Fabric Watch legacy policies” on page 23 for more information about Fabric Watch converted

policies.

You can monitor your switch for a while using the default policy, then fine-tune the policy as

necessary to fit your environment. When you are satisfied with the configuration settings, you

activate the actions you want to happen when thresholds are crossed.

To monitor a switch in this manner, complete the following steps.

1. Enable MAPS using mapsConfig --enablemaps.

2. Migrate from Fabric Watch using the default policy mapsConfig --fwconvert -enablepolicy.

Refer to “MAPS and Fabric Watch” on page 2 for more details.

Unless you specify otherwise, as part of the migration, Fabric Watch configurations are not

converted to MAPS policies, Fabric Watch commands are disabled, and MAPS commands are

enabled. The default active policy is named dflt_conservative_policy.

8 Monitoring and Alerting Policy Suite Administrator’s Guide

53-1002933-02

MAPS configuration tasks

2

3. Set global actions on the switch to none using use mapsConfig --actions none.

Setting the global actions to “none” allows you to test the configured thresholds before

enabling the actions. Refer to “MAPS actions” on page 27 for more details.

4. Monitor the switch using mapsDb --show or mapsDb --show all.

Refer to “Viewing the MAPS dashboard” on page 41 more details.

5. Fine-tune the rules used by the policy as necessary.

Refer to “Modifying a policy” on page 25 more details.

6. Set global actions on the switch to the allowed actions by using mapsConfig --actions and

specifying all of the actions that you want to allow on the switch.

Refer to “Enabling or disabling actions at a global level” on page 28 more details.

The following example enables MAPS, loads the policy named “dflt_aggressive_policy”, sets the

actions to none, and then sets approved actions.

switch:admin> mapsconfig --enablemaps

switch:admin> mapsconfig --fwconvert -policy dflt_aggressive_policy

WARNING:

This command enables MAPS and replaces all Fabric Watch configurations and

monitoring. Once MAPS is enabled, the Fabric Watch configuration can't be

converted to MAPS.

If you wish to convert your Fabric Watch configuration into MAPS policies, select

NO to this prompt and first issue the "mapsconfig --fwconvert" command. Once the

Fabric Watch configuration is concerted into MAPS policies, you may reissue the

"mapsconfig --enablemaps" command to continue this process. If you do not use

Fabric Watch or need the configuration, then select YES to enable MAPS now.

Do you want to continue? (yes, y, no, n): [no] yes

...

MAPS is enabled.

switch:admin> mapsconfig --actions none

switch:admin> mapsconfig --actions raslog,fence,snmp,email,sw_marginal

MAPS configuration tasks

Table 2 lists the MAPS configuration tasks and the commands you use for these tasks.

TABLE 2 MAPS configuration tasks

Configuration task Command

Enabling MAPS mapsconfig --enablemaps

Migrating from Fabric Watch to MAPS

(Converting Fabric Watch policies to MAPS policies)

mapsconfig - -fwconvert

Viewing group information logicalgroup --show

Modifying a policy mapspolicy

Creating a policy mapspolicy --create

Enabling a policy mapspolicy --enable

Modifying a default policy mapspolicy --clone

Adding a rule to a policy mapspolicy --addrule

Page is loading ...

Dell Brocade M6505 User guide

This manual is also suitable for

Dell Brocade M6505 User guide

Related papers

Other documents