Cal Amp LandCell-819 1XRT User manual

Category
Modems
Type
User manual

This manual is also suitable for

8
8
1
1
9
9
-
-
1
1
X
X
R
R
T
T
-
-
X
X
X
X
X
X
CDMA 1xRTT Serial Cellular Data Modem
User Manual
001-0003-819
Revision 1; February 2008
REVISION HISTORY
Released February 2008
TABLE OF CONTENTS
SECTION
1
PREFACE
........................................................................................................ 5
SECTION 1 – PREFACE
Copyright Notice............................................................................................................. 5
Modem Use.................................................................................................................... 5
Interference Issues......................................................................................................... 5
Mobile Application Safety................................................................................................. 6
SECTION
2
PRODUCT
OVERVIEW
...................................................................................... 7
SECTION 2 – PRODUCT OVERVIEW
Module Identification....................................................................................................... 7
General Description ........................................................................................................7
Features and Benefits...................................................................................................... 7
Catalog Part Number Breakdown.......................................................................................7
External Connections ......................................................................................................8
Front panel connections ............................................................................................... 8
Back panel connections................................................................................................8
RS-232 Serial Port Integration Parameters......................................................................9
Accessories & Options..................................................................................................9
SECTION
4
GETTING
STARTED
........................................................................................ 10
SECTION 4 – GETTING STARTED
Package Contents......................................................................................................... 10
Setting up the 819-1XRT Modem using the CDMA 819S Driver:........................................... 10
Setting up the CDM-819S using native Windows drivers:.................................................... 14
Configuring the Modem ................................................................................................. 14
Creating a Dial-Up Networking (DUN) connection .............................................................. 14
Operational States........................................................................................................ 21
Activating your Modem.................................................................................................. 21
SECTION
5
819-1XRT
FAST-TRACK
CALL
SETUP
GUIDES
.................................................... 23
SECTION 5 – 819-1XRT FAST-TRACK CALL SETUP GUIDES
Circuit Switch Data (CSD) Call Setup............................................................................... 23
Packet Data Call Setup.................................................................................................. 24
SECTION
6
CARRIER
SPECIFIC
INFORMATION
................................................................... 26
SECTION 6 – CARRIER SPECIFIC INFORMATION
Verizon Wireless Subscribers.......................................................................................... 26
Sprint PCS Subscribers.................................................................................................. 27
Alltel Subscribers.......................................................................................................... 28
Telus (Canada) Subscribers............................................................................................ 29
SECTION
7
TROUBLESHOOTING
...................................................................................... 30
SECTION 7 – TROUBLESHOOTING
Helpful Hints................................................................................................................ 30
Diagnosing COM Port Problems Using HyperTerminal ......................................................... 30
Altering The Modem’s Cellular Parameters........................................................................ 31
Entering Offline Digital Mode .......................................................................................... 31
Unlocking The Service Programming Code (SPC)............................................................... 32
Entering The Mobile Directory Number (MDN)................................................................... 32
Entering The MSID/MIN Number..................................................................................... 32
Entering The Mobile Country Code (MCC)......................................................................... 32
Entering The Mobile Network Code (MNC) ........................................................................ 32
SECTION
8
USER
PROFILES
............................................................................................ 33
SECTION 8 – USER PROFILES
SECTION
9
COMMON
AT
COMMAND
REFERENCE
GUIDE
...................................................... 34
SECTION 9 – COMMON AT COMMAND REFERENCE GUIDE
SECTION
10
AT
COMMAND
REFERENCE
............................................................................ 36
SECTION 10 – AT COMMAND REFERENCE
AT Command Types...................................................................................................... 36
Command Line Syntax .................................................................................................. 36
Result Codes................................................................................................................ 36
Basic AT Parameters ..................................................................................................... 37
S-Registers.................................................................................................................. 37
Basic Action Commands................................................................................................. 38
Extended Commands .................................................................................................... 38
Cellular CDMA Commands.............................................................................................. 40
SECTION
11
SPECIFICATIONS
........................................................................................ 44
SECTION 11 – SPECIFICATIONS
General Specifications................................................................................................... 44
TABLE OF CONTENTS
Mechanical Specifications............................................................................................... 45
SECTION
12
ABBREVIATIONS
......................................................................................... 46
SECTION 12 – ABBREVIATIONS
SECTION
13
SERVICE
AND
SUPPORT
............................................................................... 47
SECTION 13 – SERVICE AND SUPPORT
Product Warranty, RMA and Contact Information............................................................... 47
RMA Request ............................................................................................................... 47
Product Documentation ................................................................................................. 47
Technical Support......................................................................................................... 47
APPENDIX
1
WARRANTY
STATEMENT
............................................................................... 48
APPENDIX 1 – WARRANTY STATEMENT
001-0003-819 Rev 1
Page 5 of 48
S
S
E
E
C
C
T
T
I
I
O
O
N
N
1
1
P
P
R
R
E
E
F
F
A
A
C
C
E
E
Copyright Notice
©2008 CalAmp. All Rights Reserved.
This manual covers the operation of the CalAmp 819-1XRT Serial Cellular Data Modems.
Specifications described are typical only and are subject to normal manufacturing and
service tolerances.
CalAmp reserves the right to modify the equipment, specifications or this manual without
prior notice, in the interest of improving performance, reliability or servicing. At the time of
publication, all data is correct for the operation of the equipment at the voltage and/or
temperature referred to. Performance data indicates typical values related to the particular
product.
No part of this documentation or information supplied may be divulged to any third party
without the expressed written consent of CalAmp.
Products offered may contain software which is proprietary to CalAmp. The offer or supply
of these products and services does not include or infer any transfer of ownership.
Modem Use
The 819-1XRT modem is designed and intended for use in fixed and mobile applications.
“Fixed” assumes the device is physically secured at one location and not easily moved to
another location. Please keep the cellular antenna of the 819-1XRT at a safe distance from
your head and body while the modem is in use (see below).
Important
Maintain a distance of at least 20 cm (8 inches) between the transmitter’s antenna and any
person while in use. This modem is designed for use in applications that observe the 20 cm
separation distance.
Interference Issues
Avoid possible radio frequency (RF) interference by following these guidelines:
The use of cellular telephones or devices in aircraft is illegal. Use in aircraft may
endanger operation and disrupt the cellular network. Failure to observe this
restriction may result in suspension or denial of cellular services to the offender,
legal action or both
Do not operate in the vicinity of gasoline or diesel-fuel pumps unless use has been
approved and authorized
Do not operate in locations where medical equipment that the device could interfere
with may be in use
Do not operate in fuel depots, chemical plants, or blasting areas unless use has been
approved and authorized
Use care if operating in the vicinity of protected personal medical devices, i.e.,
hearing aids and pacemakers
Operation in the presence of other electronic equipment may cause interference if
equipment is incorrectly protected. Follow recommendations for installation from
equipment manufacturers
001-0003-819 Rev 1
Page 6 of 48
Mobile Application Safety
Do not change parameters or perform other maintenance of the 819-1XRT while
driving
Road safety is crucial. Observe National Regulations for cellular telephones and
devices in vehicles
Avoid potential interference with vehicle electronics by correctly installing the
819-1XRT. CalAmp DataCom recommends installation by a professional
001-0003-819 Rev 1
Page 7 of 48
S
S
E
E
C
C
T
T
I
I
O
O
N
N
2
2
P
P
R
R
O
O
D
D
U
U
C
C
T
T
O
O
V
V
E
E
R
R
V
V
I
I
E
E
W
W
Module Identification
Label Information
The label contains the CalAmp DataCom part number, serial number, FCC ID and the ESN
number. The ESN number is required by your cellular carrier when activating your data
contract. The ESN number is provided in decimal and Hex formats; format is dependent on
your carrier type.
ESN Dec: The Electronic Serial Number of the cellular module in decimal format.
ESN Hex: Same number as above but in a special HEX format.
General Description
The 819-1XRT Cellular Data Modem from CalAmp is the ideal solution for a wide range of
cellular data network serial connectivity requirements.
The 819-1XRT version features CDMA 1xRTT speeds. The 819-1XRT supports both circuit-
switched and packet-switched services.
Features and Benefits
1xRTT Dynamic or Static IP (Mobile IP/DMU)
RS-232 connector
Dual Band Digital CDMA 800 MHz and CDMA PCS 1900 MHz
Circuit Switch Data origination and Termination
PPP originated Tethered Data Calls for TCP/IP capable devices
Packet data transmission speeds up to 153 kbps
RSSI indicator
Optional AGPS
Optimized for OEM applications
Catalog Part Number Breakdown
819-1XRT-XXX (XXX = Carrier Identifier)
VZW = Verizon Wireless
ALT = Alltel
SPN = Sprint
TMC = Telus (Canada)
001-0003-819 Rev 1
Page 8 of 48
External Connections
Front panel connections
Fig. 2.1 819-1XRT Front Panel
819-1XRT front panel indicators include:
PWR: Green LED indicating power to unit.
Tx: Red LED indicating Transmit activity.
DCD: Amber LED indicating Data Carrier Detect from cellular network.
Rx: Green LED indicating Receive activity.
RF: SMA female, primary antenna connection.
AGPS: SMA female, optional AGPS antenna connection.
Back panel connections
Fig. 2.2 819-1XRT Back Panel
819-1XRT back panel connections include:
Power connector: 2.1mm x 5.5mm DC Barrel Jack (Center Positive)
RS-232 port: Standard DE-9 female
001-0003-819 Rev 1
Page 9 of 48
RS-232 Serial Port Integration Parameters
Table 2.1 provides the serial cable design information to integrate the 819-1XRT into your
system.
Table 2.1 Standard RS-232 DE-9 Pin out
Pin Name Direction Description
1 CD «— Carrier Detect
2 RX «— Receive Data
3 TX —» Transmit Data
4 DTR —» Data Terminal Ready
5 GND System Ground
6 DSR «— Data Set Ready
7 RTS —» Request to Send
8 CTS «— Clear to Send
9 RI «— Ring Indicator
Note: Direction is DTE relative DCE.
Table 2.2 Default RS-232 Communication Parameters
Bits Per Second 115,200
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
Accessories & Options
Accessory/Option Description Order Number
Antenna
4” Rubber Duck Antenna
3” Mag Mount Antenna
L2-ANT0001
L2-ANT0003
Power Supply
110 VAC input
DC Power Cable
L2-PWR0001
L2-PWR0002
Interface Cable Serial Cable L2-CAB0002
AGPS Option Installed AGPS antenna connector 823-7500-501
Primary Antenna
The primary and optional AGPS antenna connections on the 819-1XRT are female connectors.
Purchase antennas with SMA male connectors. Do not select an SMA antenna with “reverse
polarity” or RP-Male. When using a direct mount or “rubber duck” antenna, choose the antenna
specific to your band requirements. Mounting options and cable lengths are user’s choice and
application specific.
001-0003-819 Rev 1
Page 10 of 48
S
S
E
E
C
C
T
T
I
I
O
O
N
N
4
4
G
G
E
E
T
T
T
T
I
I
N
N
G
G
S
S
T
T
A
A
R
R
T
T
E
E
D
D
Package Contents
819-1XRT cellular data modem (specific to CDMA cellular provider)
Information card
Setting up the 819-1XRT Modem using the CDMA 819S Driver:
You may download the necessary modem driver files from our website at http://www.calamp.com. If
you are installing the modem using the drivers from the website, refer to these steps:
1. Click on Start --> Settings --> Control Panel. Select "Phone and Modem Options".
001-0003-819 Rev 1
Page 11 of 48
2. Select the “Modem” tab. Select “Add...” and complete the Wizard. Check “Don’t Detect My
Modem”.
001-0003-819 Rev 1
Page 12 of 48
3. Select "Have Disk…" Click “Next”.
4. Browse to the file location where the CDMA 819S modem driver was downloaded.
001-0003-819 Rev 1
Page 13 of 48
5. Select the KYOCERA WIRELESS CORP. manufacturer and Kyocera High-Speed CDMA
Wireless Modem model. Click “Next”.
6. Assign the modem to the COM port connected to the modem. Click “Next”.
7. Click “Finish”.
001-0003-819 Rev 1
Page 14 of 48
Setting up the CDM-819S using native Windows drivers:
1. Click on Start --> Settings --> Control Panel. Select "Phone and Modem Options".
2. Select the “Modem” tab. Select “Add.Complete the Wizard. Check “Don’t Detect My Modem”.
3. Select "Standard 19200 bps Modem." Click “Next”.
4. Assign the modem to the COM port connected to the modem. Click “Next”.
5. Click “Finish”.
Configuring the Modem
1. Click on Start --> Settings --> Control Panel. Select "Phone and Modem Options".
2. Click “New” or “Edit” to add or modify a location name.
3. In "Location Name", enter a name to distinguish this connection as the 819-1XRT modem. Type
your area code in the Area Code box.
4. Click "Apply" and “OK”. The window should exit out to the Phone and Modem Options box.
5. Click the tab at the top titled "Modems". Select the "Kyocera High-Speed Modem" (or the
"Standard 19200 bps Modem" if you’re using the native Windows driver) and click "Properties".
6. Click the "Modem" tab at the top of this new box. The box titled "Maximum Port Speed" should
read: 115200. If not, scroll down to select 115200. Click “OK”. Click "Apply".
7. Click “OK”.
Creating a Dial-Up Networking (DUN) connection
1. Click on Start --> Settings --> Control Panel. Select "Network Connections".
001-0003-819 Rev 1
Page 15 of 48
2. From the Network Connections screen, select “Create a new connection”. Follow the Wizard as it
goes through the steps to create a dial-up connection by selecting “Next”.
3. For the connection type, select “Connect to the Internet”. Click “Next”.
001-0003-819 Rev 1
Page 16 of 48
4. Select “Set up my connection manually. Click “Next”.
5. For the Internet connection, select “Connect using a dial-up modem”. Click Next”.
001-0003-819 Rev 1
Page 17 of 48
6. Check the box by the modem for the CDMA device. Click “Next”.
7. Type in a connection name. Click “Next”.
001-0003-819 Rev 1
Page 18 of 48
8. Type in #777 for the phone number to dial. This is the number for 1xRTT packet data calls.
9. Typically the username and password are left blank. Click “Next”.
10. Click “Finish” in the Wizard. The network connection should now be available on the Network
Connections screen.
To verify the DUN connection is configured properly, go to the Network Connections screen and
double click on the Dial-up connection for the 819-1XRT CDMA modem. The Connect 819s CDMA
connection screen will appear. Selecting Dial would initiate the Dial Up Connection. To check the
settings, select Properties.
001-0003-819 Rev 1
Page 19 of 48
From the Properties window, confirm the correct modem driver is checked under “Connect using:”
and select Configure.
001-0003-819 Rev 1
Page 20 of 48
In the Configuration window, confirm the maximum speed (bps) is set to 115200, as shown in the
Modem Configuration Screen. Click OK to exit out of each screen.
Refer to Packet Data Call Setup in Section 5 for further information on call setup procedures.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Cal Amp LandCell-819 1XRT User manual

Category
Modems
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI