MacDon MD #215092 A FM100 Installation guide

FM100FloatModule

GEARPULLERTOOL(MD#304800)

INSTRUCTIONS



215092 RevisionA Page1of3

TheGearPullerTool(MD#304800)isdesignedtoassistDealerswithinstallingtheGearset89/36kit(B6191)or

Gearset97/28kit(B6192)ontheFM100FloatModule.Thisdocumentexplainshowtousethetool.

Alistofpartsincludedinthekit

isprovided.

NOTE:KeepyourMacDonpublicationsup‐to‐date.Themostcurrentversionofthisinstructioncanbedownloaded

fromourDealer‐onlysite(https://portal.macdon.com)(loginrequired).

NOTE:ThisinstructionisavailableinEnglishonly.

Conventions

Thefollowingconventionsareusedinthisdocument:

 Rightandleft

aredeterminedfromtheoperator’sposition.Thefrontoftheheaderisthesidethatfaces

thecrop;thebackoftheheaderisthesidethatconnectstothecombine.

 Unlessotherwisenoted,usethestandardtorquevaluesprovidedintheheaderoperator’smanualand

technicalmanual.





FM100FloatModule

GEARPULLERTOOL(MD#304800)

INSTRUCTIONS



215092 RevisionA Page2of3

PartsList

Thiskitincludesthefollowingparts:



Figure1:PartsIncludedinKit

Ref

Part

Number

Description Quantity

1 NSS

 BAR 1

 

A 18598 WASHER–SAEFLAT13/32IDX13/16INODZP 2

B 30035 BOLT–HEXHD3/8‐16X2.75GR5‐AA1J 2

C 50072 BOLT–HH1/2NCX1.75TFLGR5ZP 1





Notsoldseparately

FM100FloatModule

GEARPULLERTOOL(MD#304800)

INSTRUCTIONS



215092 RevisionA Page3of3

Instructions



DANGER

Toavoidbodilyinjuryordeathfromunexpectedstart‐uporfallofraisedmachine,alwaysstopengine,remove

key,andengagesafetypropsbeforegoingunderheaderforanyreason.

TousetheGearPullerTool(MD#304800),followthesesteps:

1. Removecotterpinandcastlenutfrompump

output

shaft(D).

2. Lineupouterbolts(A)ongearpullerwithholesin

gear(B),andlineupcenter1/2in.bolt(C)with

outputshaft(D).



3. Hand‐tightenouterbolts(A)ongearpuller,making

suretheboltsgocompletelythroughthegear.

4. Tightencenter

1/2in.bolt(B)toremovegearfrom

shaft.Ifthegeardoesnotloosen,givethecenter

boltatapwithahammer.

NOTE:Thekeymayormaynotcomeoffwiththe

gear.DoNOTlosethekey.



Theinformation

inthispublicationisbasedontheinformationavailableandineffectatthetimeofprinting.

MacDonIndustries,Ltd.makesnorepresentationorwarrantyofanykind,whetherexpressedorimplied,with

respecttotheinformationinthispublication.MacDonIndustries,Ltd.reservestherighttomakechangesatany



timewithoutnotice.

Figure2:GearPullerTool

Figure3:GearPullerTool

MacDon MD #215092 A FM100 Installation guide

Related papers

Other documents