Vision Fitness E3000 Assembly Manual
- Category
- Spin bikes
- Type
- Assembly Manual
This manual is also suitable for
Assembly
Guide
E3100 AND E3000
UPRIGHT FITNESS CYCLES
1
STEP
3
STEP
4
STEP
4
STEP
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding, find
your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
E3100 AND E3000
UPRIGHT FITNESS CYCLES
TOOLS & PARTS INCLUDED
5
MM
Allen Wrench
15
MM
Pedal Wrench
Screwdriver
5
MM
L-Shaped Wrench
PARTS BOX
Water Bottle & Bracket, Qty: 1
Power Supply, Qty: 1 (E3100 ONLY)
Tension Control Knob and bracket,
Qty: 1 (E3000 ONLY)
Pedals, Qty: 2
Seat Post Knob, Qty: 1
Color-coded Hardware Bags, Qty: 1
Owner’s Guide, Qty: 1
Assembly Guide, Qty: 1
Warranty Card, Qty:1
14
MM
Seat Wrench
HARDWARE INCLUDED
ORANGE BAG
PINK BAG
M8 x 20L Screw
Quantity: 2
M8 Lockwasher
Quantity: 4
M5 x 70L Screws
Quantity: 1
(E3000 ONLY)
M8 x 15L Screws
Quantity: 7
M8 Lockwashers
Quantity: 8
M8 x 65L Screw
Quantity: 2
M8 x 20L Screw
Quantity: 2
M5 x 15L Screws
Quantity: 2
M5 Washer
Quantity: 1
(E3000 ONLY)
1
STEP
• Slide the rear foot into place and
secure with two bolts (M8x20L) and
two lock washers (M8) to the outside
holes. Secure with two bolts (M8x65L)
and two lock washers (M8) to the inside
holes. Tighten with the 5
MM
Allen
wrench.
ORANGE BAG
1
STEP
5
6
2
STEP
• Slide the console mast cover onto
the console mast. With the included
wire-tie, pull the wire harness or RPM
sensor wire through the console mast.
Place the console mast into the
console mast mounting-bracket and
secure with seven bolts (M8x15L) and
six lock washers (M8). Tighten with
the 5
MM
Allen wrench. Slide the con-
sole mast cover into place so it inte-
grates with the frame.
• MODEL E3000: Turn the tension
knob to level 16. Direct the cable on
the tension knob through the tension
knob bracket and into the console
mast. Connect the cable to the tension
cable located inside the console mast.
Secure the tension knob to the console
mast with the washer (M5) and screw
(M5x70L). Tighten with Phillips
screwdriver.
• Secure the handlebar onto the
handlebar bracket with two bolts
(M8x20L) and two lock washers
(M8). Tighten with the 5
MM
Allen
wrench.
• Remove the four mounting screws
from the back of the console. Connect
the wire harness to the console.
Attach the console to the console mast
using the four mounting screws that
were just removed.
• MODEL E3000: Secure the water
bottle bracket to the console mast with
the 4
MM
L-shaped wrench and two cap
screws (M5x35L). Attach the water
bottle cage to the bracket with
two screws (M5x15L) using the
screwdriver. Insert the water bottle into
the cage.
• MODEL E3100: Attach the water
bottle cage to the console mast with
two screws (M5x15L) using the
screwdriver. Insert the water bottle into
the cage.
PINK BAG
E3000 ONLY
2
STEP
E3100 ONLY
3
STEP
• Slide the seat post cover onto the
seat post
• Slide the seat post into the frame
and lower the seat post cover into
place.
• Screw the adjustment knob through
the seat post cover and into place on
the frame.
• Attach the seat to the seat post by
tightening the bolts on the underside
of the seat. Use the 14
MM
Seat
Wrench.
GREEN BAG
3
STEP
7
8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z30CB35-AG1818PRD
AG18.18PRD
REV1
4
STEP
• Attach the left and right pedals to
the left and right crank arms, tighten
using the 15
MM
pedal wrench.
PEDALS
4
STEP
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Vision Fitness E3000 Assembly Manual
- Category
- Spin bikes
- Type
- Assembly Manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Vision Fitness Fitness Cycle E3100 Assembly Manual
-
-
-
-
-
-
-
-
-
