5mm T-Shaped Wrench
Screwdriver
TOOLS & PARTS INCLUDED
ORANGE BAG
PINK BAG
HARDWARE INCLUDED
PARTS BOX
Console Mast Cover
Accessory Tray
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
BLUE BAG
M8 x 15L Bolt
Quantity: 7
M8 x 20L Bolt
Quantity: 2
M8 x 65L Bolt
Quantity: 2
M8 Lock Washer
Quantity: 4
M8 x 15L Bolt
Quantity: 4
15mm Pedal Wrench
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373
www.visionfitness.com
©2007 Vision Fitness. All Rights Reserved. 5.07
AG18.45PRD
REV3
starts
vision
with a
it all
Assembly
Guide
E3800HRT
COMMERCIAL FITNESS BIKES
M8 Lock Washer
Quantity: 6
5mm L-Shaped Wrench
5mm T-Shaped Wrench
Screwdriver
TOOLS & PARTS INCLUDED
ORANGE BAG
PINK BAG
HARDWARE INCLUDED
PARTS BOX
Console Mast Cover
Accessory Tray
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
BLUE BAG
M8 x 15L Bolt
Quantity: 7
M8 x 20L Bolt
Quantity: 2
M8 x 65L Bolt
Quantity: 2
M8 Lock Washer
Quantity: 4
M8 x 15L Bolt
Quantity: 4
15mm Pedal Wrench
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373
www.visionfitness.com
©2007 Vision Fitness. All Rights Reserved. 5.07
AG18.45PRD
REV3
starts
vision
with a
it all
Assembly
Guide
E3800HRT
COMMERCIAL FITNESS BIKES
M8 Lock Washer
Quantity: 6
5mm L-Shaped Wrench
2
STEP
• Slide the console mast boot onto the
console mast.
• Unfold the wire harness, coaxial
cable, and TV power cable located in
the console mast frame bracket.
Connect the cables and wire harness to
the wire tie coming from the bottom of
the console mast. Pull the wire tie and
cables up through the top of the console
mast while simultaneously sliding the
mast into the frame bracket.
• Secure the mast to the frame using
six lock washers (M8) and six bolts
(M8x15L). Tighten with the 5mm
T-shaped wrench. Place the seventh
bolt (M8x15L) in the rear of the frame
bracket and tighten until snug. Tighten
with the 5mm L-shaped wrench.
• Slide the console mast boot down
and set it in place on the side cover.
• Remove the nuts (M8) from the bottom
of the seat. Attach the seat to the seat
post with the nuts you just removed.
Tighten with the 15mm wrench.
BLUE BAG
3
STEP
• Feed the heart rate wires of the
handlebar through the small hole located
in the front of the console mast. Pull
these wires up through the hole at the
top of the console mast. Attach the
handlebar to the console mast using
four bolts (M8x15L). Tighten with the
5mm T-shaped wrench.
• Tuck the coaxial and TV power
cables into the console mast.
NOTE:
If you have purchased the TV
bracket assembly, remove the bolts
from the TV bracket cover located at
the front of the console mast and
remove the cover. Feed the coaxial
and TV power cables through the hole
at the front of the console mast.
PINK BAG
1
STEP
• Install the rear foot with four lock
washers (M8), two inside bolts
(M8x65L), and two outside bolts
(M8x20L). Tighten with the 5mm
T-shaped wrench.
ORANGE BAG
Assembly
Guide
E3800HRT
COMMERCIAL FITNESS BIKE
1
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.
Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble
your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts
and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.
4
STEP
• Remove the four mounting bolts from
the back of the console with the
screwdriver. Plug in the wire harness
and the two heart rate wires to the
back of the console. Attach the console
to the console mast with the four bolts
removed earlier in this step.
• With the screwdriver, remove the two
bolts located half way up the console
mast. Attach the accessory tray to the
console mast with the two bolts.
CONSOLE
3
STEP
4
STEP
Handlebar
Rear Foot
Console Mast
Console Mast
Boot
Frame
Bracket
Heart Rate
Wires
Wire Harness
2
STEP
Accessory
Tray
Console
TV Bracket
Wires
/