Comprehensive EXT-VGA-DVI-SC User manual

EXT-VGA-DVI-SC

User Manual

VGA to DVI

Scaler/Converter

*Preferred

Release A2

ii

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this product near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install or place this product near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the third prong are provided for

your safety. If the provided plug does not t into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. To reduce the risk of electric shock and/or damage to this product, never handle or

touch this unit or power cord if your hands are wet or damp. Do not expose this

product to rain or moisture.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

15. Batteries that may be included with this product and/or accessories should never be

exposed to open ame or excessive heat. Always dispose of used batteries

according to the instructions.

Important Safety Instructions

Gefen warrants the equipment it manufactures to be free from defects in material and

workmanship.

If equipment fails because of such defects and Gefen is notied within two (2) years from

the date of shipment, Gefen will, at its option, repair or replace the equipment, provided

that the equipment has not been subjected to mechanical, electrical, or other abuse or

modications. Equipment that fails under conditions other than those covered will be

repaired at the current price of parts and labor in effect at the time of repair. Such repairs

are warranted for ninety (90) days from the day of reshipment to the Buyer.

This warranty is in lieu of all other warranties expressed or implied, including without

limitation, any implied warranty or merchantability or tness for any particular purpose, all of

which are expressly disclaimed.

1. Proof of sale may be required in order to claim warranty.

2. Customers outside the US are responsible for shipping charges to and from Gefen.

3. Copper cables are limited to a 30 day warranty and cables must be in their original

condition.

The information in this manual has been carefully checked and is believed to be accurate.

However, Gefen assumes no responsibility for any inaccuracies that may be contained

in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or

consequential damages resulting from any defect or omission in this manual, even if

advised of the possibility of such damages. The technical information contained herein

regarding the features and specications is subject to change without notice.

For the latest warranty coverage information, refer to the Warranty and Return Policy under

the Support section of the Gefen Web site at www.gefen.com.

iii

Warranty Information

iv

Technical Support

(818) 772-9100 (800) 545-6900

8:00 AM to 5:00 PM Monday - Friday, Pacic Time

Fax

(818) 772-9120

Email

[email protected]

Web

http://www.gefen.com

Mailing Address

Gefen, LLC

c/o Customer Service

20600 Nordhoff St.

Chatsworth, CA 91311

Product Registration

Register your product here: http://www.gefen.com/kvm/Registry/Registration.jsp

iv

Contacting Gefen Technical Support

v

• By default, the current input and output resolution will be displayed whenever the

VGA to DVI Scaler/Converter is disconnected from the source or display or if a change

in the video output settings are made. This feature can be disabled through the

Display Notify option See Display Notify (page 33).

• Always make sure that the VGA to DVI Scaler/Converter is running the latest rmware.

The Gefen Syner-G™ Software Suite is a free downloadable application from Gefen

that provides automatic download and installation of rmware upgrades for this

product.

Download the application here: http://www.gefen.com/synerg/

VGA to DVI Scaler/Converter is a trademark of Gefen, LLC.

Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation

without prior written notice.

v

Operating Notes

This product uses UL or CE listed power supplies.

Pb

vi

Features and Packing List

Features

• Converts and scales VGA to DVI

• Input resolutions up to 1920 x 1200 (WUXGA)

• Output resolutions up to 1080p60 and 1920 x 1200 (WUXGA)

• On-screen display (OSD) menu allows easy set-up and control

• Aspect Ratio Control: Full Screen, Panoramic, Letter/Pillar, Extract/Crop

• Test Pattern Generator for quick system conguration

• Gefen Syner-G™ simplies in-eld rmware updates and advanced EDID

management including custom input timings

• USB port for use with Gefen Syner-G™

• Wide power supply operating range (6V to 24V DC)

• Locking power supply connector

• Surface mountable

Packing List

The VGA to DVI Scaler/Converter ships with the items listed below. If any of these items

are not present in the box when you rst open it, immediately contact your dealer or Gefen.

• 1 x VGA to DVI Scaler/Converter

• 1 x 6 ft. VGA cable (M-M)

• 1 x 12V Power Supply

• 1 x Quick-Start Guide

This page left intentionally blank.

viii

Table of Contents

1 Getting Started

Introduction............................................................................................................ 2

Installation ............................................................................................................. 4

Connection Instructions ................................................................................. 4

Sample Wiring Diagram ................................................................................ 4

2 Basic Operation

Menu System ........................................................................................................ 8

Displaying the Menu System ......................................................................... 8

Moving around within the Menu System ....................................................... 9

Output Resolution ....................................................................................... 12

Contrast ....................................................................................................... 14

Brightness ................................................................................................... 15

Saturation .................................................................................................... 16

Hue .............................................................................................................. 17

Color Range ................................................................................................ 18

Color Temperature ...................................................................................... 19

Color Balance .............................................................................................. 20

Edge Enhance ............................................................................................. 21

Sharpness ................................................................................................... 22

Underscan/Overscan .................................................................................. 23

Aspect Ratio ................................................................................................ 24

Horizontal Mirror .......................................................................................... 25

Vertical Mirror .............................................................................................. 27

Horizontal Shift ............................................................................................ 29

Vertical Shift ................................................................................................ 30

Phase .......................................................................................................... 31

OSD Timeout .............................................................................................. 32

Display Notify .............................................................................................. 33

Input Resolution Information ....................................................................... 35

F/W Version ................................................................................................ 36

Factory Reset .............................................................................................. 37

Test Patterns ............................................................................................... 38

DIP Switch Conguration .................................................................................... 40

ix

Table of Contents

3 Appendix

Menu System Summary ...................................................................................... 44

Default Settings ................................................................................................... 50

USB Interface ...................................................................................................... 51

Installing the Virtual COM Port .................................................................... 51

Updating the Firmware ........................................................................................ 53

Surface Mounting Instructions ............................................................................. 58

Specications ...................................................................................................... 59

Index.................................................................................................................... 60

This page left intentionally blank.

VGA to DVI

Scaler/Converter

1 Getting Started

page | 2

Page Title

VGA to DVI

Scaler/Converter

®

DVI Out Up Dn Menu

EXT-VGA-DVI-SC

VGA In USB 12V DC Pwr

VGA to DVI

Scaler/Converter

®

DVI Out Up Dn Menu

EXT-VGA-DVI-SC

VGA In USB 12V DC Pwr

VGA to DVI

Scaler/Converter

®

DVI Out Up Dn Menu

EXT-VGA-DVI-SC

VGA In USB 12V DC Pwr

Introduction

3 4 65

Getting Started

1 2

page | 3

Page TitleIntroduction

ID Name Description

1 DVI Out Use a DVI cable to connect a DVI display

to this port.

2 Up, Dn, Menu These push-buttons are used to change

settings within the on-screen menu system.

See Menu System (page 8) for more

information.

3 VGA In Connect the included VGA cable from

source device (e.g. computer) to this port.

4 USB This mini-USB port is used for upgrading

the rmware.

5 12V DC Connect the included 12V DC power supply

to this power receptacle.

6 Pwr Under normal operating conditions, this

LED indicator will glow bright blue.

Getting Started

page | 4

Connection Instructions

► Video

1. Connect the included VGA cable from the video source (e.g. computer) to the VGA In

port on the VGA to DVI Scaler/Converter.

2. Connect a DVI cable from the DVI Out port to a DVI display.

► USB (optional Syner-G™ software control)

3. Connect a USB-to-mini USB cable from the VGA to DVI Scaler/Converter to a

computer that is running the Syner-G™ Software Suite. To complete this portion

of the installation, see USB Interface (page 51). This connection is required for

updating the rmware.

► Power

4. Connect the included power supply to the 12V DC power receptacle and connect the

power cord to an available electrical outlet.

Sample Wiring Diagram

Installation

Getting Started

VGA Source

VGA CABLE

DVI CABLE

EXT-VGA-DVI-SC

DVI Display

EXT-VGA-DVI-SC

Scaler/Converter

This page left intentionally blank.

VGA to DVI

Scaler/Converter

2 Basic Operation

page | 8

VGA to DVI

Scaler/Converter

®

DVI Out Up Dn Menu

EXT-VGA-DVI-SC

VGA In USB 12V DC Pwr

Displaying the Menu System

The VGA to DVI Scaler/Converter uses a built-in menu system to manage and control all

video features.

1. To display the menu system, press the Menu button on the front panel.

2. The menu system will be displayed in the upper-left corner of the screen, as shown

below:

If the menu system is not used within the time interval specied by the OSD Timeout

setting, then the menu system will automatically be hidden. By default, the OSD

Timeout setting is 5 seconds. See OSD Timeout (page 32) for instructions on

setting the OSD Timeout value.

(continued on next page)

Menu System

Basic Operation

Gefen

Converter

----------------

1.Output Setup

2.Picture

3.Adjustment

4.System

5.Test Patterns

6.Exit

1.Output Setup

Output Resolu.

<- Back

Menu controls

page | 9

Moving around within the Menu System

1. There are six menu items within the main menu: Output Setup, Picture, Adjustment,

System, Test Patterns, and Exit.

2. The currently selected item within the main menu will always be highlighted in

yellow.

3. Each item within the main menu, with the exception of Exit, contains a submenu.

The submenu, for each item in the main menu, is displayed automatically.

4. Use the Up or Dn button to highlight the desired item within the main menu.

For example, if we press the Dn button three times, the System menu item will be

highlighted and it’s submenu will be displayed.

(continued on next page)

Basic OperationBasic Operation

Gefen

Converter

----------------

1.Output Setup

2.Picture

3.Adjustment

4.System

5.Test Patterns

6.Exit

Output Resolu.

<- Back

Main menu

Current selection

OSD Timeout

Display Notify

Input Res.Info

F/W Version

Factory Reset

<- Back

Gefen

Converter

----------------

1.Output Setup

2.Picture

3.Adjustment

4.System

5.Test Patterns

6.Exit

Menu System

Submenu

page | 10

5. To access the submenu for the highlighted item within the main menu, press the Menu

button a second time. When a submenu is activated, a green bar is used to indicate

the current selection. By default, the top submenu item will always be highlighted

once a submenu is activated.

6. Use the Up or Dn button to select the desired option within the submenu.

7. To select the highlighted submenu item, press the Menu button.

For example, if we press the Menu button when the Input Res. Info option is

highlighted, the menu system will be hidden and the following will be displayed:

8. Press the Menu button to return to the menu system.

Basic Operation

Menu System

OSD Timeout

Display Notify

Input Res.Info

F/W Version

Factory Reset

<- Back

Gefen

Converter

----------------

1.Output Setup

2.Picture

3.Adjustment

4.System

5.Test Patterns

6.Exit

OSD Timeout

Display Notify

Input Res.Info

F/W Version

Factory Reset

<- Back

Gefen

Converter

----------------

1.Output Setup

2.Picture

3.Adjustment

4.System

5.Test Patterns

6.Exit

[ 1600x1200p60 ]

a

Input Res.Info

OSD Timeout

Display Notify

Input Res.Info

F/W Version

Factory Reset

<- Back

Gefen

Converter

----------------

1.Output Setup

2.Picture

3.Adjustment

4.System

5.Test Patterns

6.Exit

Current selection

Page is loading ...

Comprehensive EXT-VGA-DVI-SC User manual

Comprehensive EXT-VGA-DVI-SC User manual

Related papers

Other documents