CAME C-BXE24 Owner's manual

Brand: CAME

Model: C-BXE24

Type: Owner's manual

#!-%

CBX

AUTOMATION FOR INDUSTRIAL AND

RESIDENTIAL ENTRANCES

INSTALLATION MANUAL

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

2.1 Destination

1 Legend

This symbol indicates sections to be read with particular care.

This symbol indicates sections concernig safety

This symbol indicates notes to communicate to users.

4.1 Gearmotor

All gearmotors are designed and built by CAME CANCELLI AUTOMATICI S.p.A. in compliance with the prevailing safety regulations.

Guaranteed for 24 months unless tampered with.

The enclosure is made up of a part in aluminium alloy inside of which the non-reversible, electromechanical gearmotor operates,

and partly in ABS plastic that houses the terminals for the electrical wiring.

The CBX series has several versions depending on the type of use - residential, condominium or industrial - with mechanical end

stop or with an encoder system (see para. 2.3 Fields of use).

The complete line:

Gearmotor 230V A.C. with encoder and control boards

001C-BXE Gearmotor 230V A.C. with encoder

002 ZCX10 - Control board

002 ZCX10C - Control board with safety block and command buttons

Gearmotor 24V A.C. with encoder and control boards

001C-BXE Gearmotor 24V A.C. with encoder

002 ZL80 -Control board

002 ZCX80C - Control board with safety block and command buttons

002 BN1 - Board for connecting 2 emergency batteries (12V - 1.2Ah)

The following standard were complied with for this product: EN 12978, UNI EN 954-1, CEI EN 60335-1, UNI EN 12453.

2 Destination and use applications

The CBX series gearmotor was designed to automate chieﬂ y sectional doors with direct transmission on the shaft using springs

or with chain drive; however, the CBX can also be used for sliding and folding doors with the respective accessories.

Uses other than the ones described above and installations using methods other than those shown in this technical

manual are considered prohibited.

3 Standard followed

4 Description

2.2 Use applications

For sectional doors with direct transmission: door height up to 5.5 m;

Speed* 7.15 m/1’ with cable winder drum ~Ø 105 mm;

Speed* 9.3 m/1’ with cable winder drum ~Ø 138 mm.

For sectional doors with chain drive: door height up to 8.5 m;

Speed* 9.15 m/1’ with cable winder drum ~Ø 208 mm.

For sliding and folding doors: door width up to 5.5 m for C-BXE / C-BXE24 / C-BXET;

door width up to 11 m for C-BX / C-BXT.

wing weight 1000 kg max.

* The speed varies depending on the diameter of the drum; in particular, models of cable winder drums used by the main sectional

door manufacturers in the speciﬁ c dimensions were inserted into the descriptions.

2.3 Fields of use

C-BX / C-BXE Residential - Condominium - Industrial

C-BXE24 Residential - Condominium

C-BXT / C-BXET Industrial

“IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION”

“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”

“THIS MANUAL IS ONLY FOR PROFESSIONAL INSTALLERS OR QUALIFIED PERSONS”

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

#!-%

4.2 Parts description

1 - Gearmotor

2 - Release handle

3 - Lower cap

4 - Protection cover

GEARMOTOR UNIT

ACCESSORIES

1 - C001 - Winch for manually moving sectional doors

2 - C002 - Pendulum release system

3 - C003 - Chain tightener transmission system and brackets

for sliding doors

4 - C004 - Chain tightener transmission system and brackets

for folding doors

5 - C005

- Chain drive system for sectional doors

6 - C006 - Package of two brackets for sectional doors

7 - C007/8 - Adapter for sectional doors

8 - CMS - Release handle with personalized key

9 - CGP - Chain guide with protective guard

10 - CCT - Simple 1/2” chain

11 - CGIU - Coupling for 1/2” chain

#!-%

Gearmotor 230V / 400V three-phase with encoder and control boards

001C-BXET - Gearmotor 230V/400V A.C. with encoder

002 ZT5 - Control board

002 ZT5C - Control board with safety block and command buttons

Gearmotor 230V A.C. with mechanical end-stop and control boards

001C-BX - Gearmotor 230V A.C. with mechanical end-stop

002 ZC3 - Control board

002 ZC3C - Control board with safety block and command buttons

Containers and electrical cards for gearmotors 230V

001S4339 - Container

001S4339C – Container with safety release and command buttons

001S4340 - Container

001S4340C – Container with safety release and command buttons

003 ZC5 - Basic electrical card

003 ZM2 - Multi-function electrical card

Gearmotor 230/400V three-phase with mechanical end-stop and control boards

001C-BXT - Gearmotor 230V/400V A.C. three phase with mechanical end-stop

002 ZT6 - Control board

002 ZT6C - Control board with safety block and command buttons

The CBX series comes with the following complementary accessories:

001 CMS - Release handle with personalized key and return cord (7 m long);

001 CGP - Chain guide with protective guard for industrial doors;

009 CCT - Simple 1/2” chain for sliding or folding doors;

009 CGIU - Coupling for 1/2” chain;

001 C001 - Winch for manually moving sectional doors;

001 C002 - Pendulum release system;

001 C003 - Chain tightener transmission system and brackets for sliding doors;

001 C004 - Chain tightener transmission system and brackets for folding doors;

001 C005 - Chain drive system for sectional doors with heights over 5.5 m;

001 C006 - Package of two brackets for sectional doors (speciﬁ c for direct transmission applications);

001 C007/8 - Adapter for sectional doors con Ø 25 mm post (C007) or Ø 40 mm post (C008);

Important! Make sure that the control and safety equipment and accessories are CAME original. Only CAME products are gua-

ranteed to make the system easy to use and maintain.

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

5.1 Preliminary checks

Before proceeding with the installation, it is necessary to:

• The gearmotor must be installed in an area protected from shocks; the anchoring surface must be solid; and appropriate parts

(screws, plugs, etc) must be used to anchor the gearmotor to the surface;

• Provide for suitable omnipolar disconnection device with more than 3 mm between contacts to section power supply.

• Connections inside the case made for protection circuit continuity are allowed as long as they include additional insulation

with respect to other internal drive parts.

• Install suitable tubes and ducts for electric cable passage to guarantee protection against mechanical damage.

• The structure of the door must be sufficiently sturdy, the hinges must be efficient and there must be no friction between fixed

or mobile parts;

• Check the presence of a mechanical end-stop during opening and closing.

Installation must be carried out by expert qualified personnel and in full observance of regulations in force.

5 Installation

SECTIONAL DOORS SLIDING DOORS

FOLDING DOORS

4.4 Size measurements

Measurements in mm

4.3 Technical information

C-BX / C-BXE GEARMOTOR

Power supply panel: 230V A.C. 50/60Hz

Motor power supply: 230V A.C. 50/60Hz

Absorption*: 3A

Rated power*: 450W

Max. torque*: 60 Nm

Reduction ratio: 1/67.45

Drive shaft revolutions: 34(CBX)/20.5(CBXE)

Motor revolution speed: 21.5 rpm

Operative intermittence: 30%

Protection level: IP54

Weight: 15 kg

Working time:

#

#

C-BXE24 GEARMOTOR

Power supply panel: 230V A.C. 50/60Hz

Motor power supply: 24V D.C.

Absorption*: 9A max.

Rated power*: 240W

Max. torque*: 25 Nm

Reduction ratio: 1/67,45

Drive shaft revolutions: 20,5

Motor revolution speed: 26,5 rpm

Operative intermittence: intensive service

Protection level: IP54

Weight: 15 kg

Working time:

C-BXT / C-BXET GEARMOTOR

Power supply panel: 230-400V A.C. - 50/60Hz

Motor power supply: 230-400V A.C.-50/60Hz

Absorption*: 2,5A

Rated power*: 780W

Max. torque*: 80 Nm

Reduction ratio: 1/67,45

Drive shaft revolutions: 34(CBXT)/20,5(CBXET)

Motor revolution speed: 21,5 rpm

Operative intermittence: intensive service

Protection level: IP54

Weight: 15 kg

Working time:

#

#

#

#

* Values relating to the designated electrical board

#!-%







All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

5.3 Cable list and minimun thickness

Connections Type of cable Length of cable 1 < 10 m Length cable 10 < 20 m Length cable 20 < 30 m

230/400V 3F power supply

FROR CEI

20-22

CEI EN

50267-2-1

4G x 1,5 mm

4G x 2,5 mm

4G x 4 mm

230V 2F power supply 3G x 1,5 mm

3G x 2,5 mm

3G x 4 mm

230/400V 2F/3F power supply motor 4G x 1,5 mm

4G x 1,5 mm

24V power supply motor 2 x 1 mm

2 x 1,5 mm

2 x 2,5 mm

24V - 230V flashing lamp 2 x 0,5 mm

2 x 1 mm

2 x 1,5 mm

Photoelectric TX 2 x 0,5 mm

2 x 0.5 mm

2 x 0,5 mm

Photoelectric RX 4 x 0,5 mm

4 x 0,5 mm

24V power supply accessory 2 x 0,5 mm

2 x 0,5 mm

2 x 1 mm

Control button 2 x 0,5 mm

2 x 0,5 mm

End stop 3 x 0,5 mm

3 x 1 mm

3 x 1,5 mm

Encoder connection 2402C 22AWG max. 30 m

Antenna connection RG58 max. 50 m

N.B.: An evaluation of the size of the cables with lengths other than the data in the table must be made based on the effective ab-

sorption of the connected devices, according to the instructions indicated by the CEI EN 60204-1 standards.

For connections that require several loads on the same line (sequential), the size given on the table must be re-evaluated based on

actual absorption and distances.















1 - Gearmotor

2 - Control panel with push-buttons

3 - Radio receiver

4 - Flaching light indicating movement

5 - Antenna

6 - Safety photocells

7 - Gearmotor release

5.2 Tools and materials

Make sure all tools and materials necessary are within reach to install the edge in maximum safety, according to regulations in

force. The following figure illustrates the minimum equipment for the installer.

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

5.4 Installing the automation on sectional doors

The following applications are only examples, as the space for installing the ratiomotor and accessories varies accord-

ing to obstructions. It is thus up to the system installer to select the most suitable solution.

C006

Fig.2

VERTICAL APPLICATION

HORIZONTAL APPLICATION

CAME

Fig.1

DIRECT TRANSMISSION - The

CBX ratiomotor is supplied

ready for installation with a

direct action on the door springs

shaft, with a shaft diameter of 1

inch (ﬁ g. 1); for special volume

requirements, it is also possible

to install it horizontally (ﬁ g. 2)

but for both cases use accessory

(Art. C006).

1) Before securing the ratiomotor, open the protection cover to facilitate

post-assembly operations.

2) Insert the ratiomotor on the spring pole using the handle on the

ratiomotor.

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH





#!-%



Fig.3

3) Manually release the ratiomotor by turning the rod clockwise

and move the door to make the pole cavity coincide with that of the

ratiomotor’s cable shaft.

4) Insert tongue A or B depending on the

type of shaft (see ﬁ g. 3) between the two

cavities, insert the bushing on the pole and

secure with the grub screw.

5) Assemble the brackets (Art. C006) and secure them (avoid-

ing blocking them) to the ratiomotor with the supplied screws.

6) Secure the brackets on the wall with suitable screws chosen

according to the shape of the wall to secure the brackets onto

the ratiomotor.

SOLID SHAFT

HOLLOW SHAFT

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

CHAIN TRANSMISSION

- Installations on sectional

doors higher than 5.5 m, for

this type of application you

must use the accessory (Art.

C005).

H > 5.5 m.

CAME

4) Secure the ﬁ xing bracket to the ratiomotor with the supplied screws.







1) Before securing the ratiomotor, open the protection cover to facilitate

post-assembly operations.

2) Insert tongue A or B (see ﬁ g.1) into the cavity

of the sprung pole, then insert toothed crown Z40

onto the pole opposite the tongue and secure it

with the grub screw.

3) Insert tongue A into the cavity of the pinion toothed sprocket shaft Z26, insert the

pinion, into the motor cable shaft and secure it with a screw UNI 5933 M6x16 and washer

from the opposite side.

Fig.1

C005

SOLID SHAFT

HOLLOW SHAFT

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

8) Then secure

the ratiomotor’s

ﬁ xing bracket with

appropriate screws

chosen according to

the shape on the wall,

being sure that the two

toothed crowns are

perpendicular to each

other.







5) Unite the two ends of the chain with the coupling and

insert it onto the toothed crown Z40 leaving it hanging.

6) Anchor the ratiomotor’s shaft pinion to the hanging chain.

7) Release the ratiomotor by hand by turning the rod clockwise.

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

5.5 Installing the automation on sliding doors

DOORS WITH ONE OR TWO WINGS - For

installations with sliding gates/doors having

one or two wings, you must use the acces-

sory C003 (transmission system for sliding

gates).

1) Before securing the ratiomotor, open the protection cover to facilitate

post-assembly operations.

2) Assemble the two ﬁ xing brackets and secure them to the ratiomotor.

3) Insert the tongue into the cavity of the toothed pinion’s shaft Z26,

insert the pinion into the motor cable shaft and secure it with a screw

(UNI 5933 M6x16) and washer from the opposite side.

4) Secure the assembly above to the right or left of the door

using suitable items chosen according to the wall’s shape.

C003

CCT CGIU







CAME

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

5) Secure the chain-tensioning transmission from the opposite side

of the ratiomotor, in line with the pinion.

CAME

9) Secure the appropriate attachments (brackets and plates) ﬁ rst

to the chain and then to the wings.

6) Insert the ½ inch chain (CCT) with a length of twice

distance A.

7) Unite the two ends with a coupling (CGIU).

8) Adjust the chain’s tension with the

transmission’s screw and then tighten the nuts.





All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

FOLDING DOORS - For installations with doors

having more than one wing, you must use ac-

cessory C004 (transmission system for folding

doors).

1) Before securing the ratiomotor, open the protection cover to facilitate

post-assembly operations.







2) Assemble the two ﬁ xing brackets and secure them to the ratiomotor.

3) Insert the tongue into the cavity of the toothed pinion’s shaft

Z26, insert the pinion into the motor cable shaft and secure it with a

screw (UNI 5933 M6x16) and washer from the opposite side.

4) Secure the assembly with suitable elements, chosen

according to the shape of the wall.

C004

CCT CGIU

CAME

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

CAME

5) Secure the chain-tensioning

transmission from the opposite

side of the ratiomotor in line with

the pinion.

6) Insert the ½ inch chain (CCT) with a length of twice

distance A.

7) Unite the two ends with a

coupling (CGIU).

8) Adjust the chain’s tension with the transmission’s screw

and then tighten the nuts.

9) Secure the chain to the pivot of the ﬁ rst wing with the

chain hitch bracket and screws UNI 5931 M8x30.

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

#ONDENS



%

#!-%

56 7%

76 5

%

5.6 Wiring gearmotors with an encoder system to the command board

For the wiring, use appropriate sheaths and cable clamps to ensure the right degree of protection.

To regulate the encoder, make reference to the technical manual of the command board.

CONTROL PANEL

ZCX10 / ZCX10C

Shielded cable 2402C 22AWG

GEARMOTOR

C-BXE

#!-%

-.  % 

%





#!-%

56 7%

765

  #/-

% 

4

CONTROL PANEL

ZL80 / ZL80C

GEARMOTOR

C-BXE24

CONTROL PANEL

ZT5 / ZT5C

GEARMOTOR

C-BXET

Shielded cable 2402C 22AWG

Additional terminal not included

Note: connect the wires of the motor protection fuse in

a series with the wire connected to the “COM” terminal.

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

5.7 Wiring gearmotors with mechanical end-stops to the command board

For the wiring, use appropriate sheaths and cable clamps to ensure the right degree of protection.

CONTROL PANEL

ZC3 / ZC3C

GEARMOTOR

C-BX

CONTROL PANEL

ZT6 / ZT6C

GEARMOTOR

C-BXT

&# &! &

#!-%

56 7%

&&#

&# &! &

#!-%

56 7%

  #/-

&# &! &

4

CLOSE PUSHBUTTON

OPEN PUSHBUTTON

POWER SUPPLY

Condenser

5.8 Direct connection by interlocking buttons only for C-BX gearmotor

#!-%

&&#

Additional terminal not included

Note: connect the wires of the motor protection fuse in

a series with the wire connected to the “COM” terminal.

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

5.9 Adjusting mechanical end-stops

Make sure the door is in a closed position

and the two crown wheels of the motor

units are both positioned to the left.

N.B.: the gearmotor is already adjusted

in a closed position, namely, the closing

end-stop micro-switch is activated.

Execute a complete opening run manually

or by using the button on the command

board; the two crowns will move to the

right.

Using a screwdriver, raise the end-stop

spring from the crown wheels; manually

move the white crown until it reaches the

opening microswitch and then lower the

spring onto the crowns.

Warning! After making the adjustments

on sectional doors in a closed position,

there may be a gap between the lower

edge of the door and the ground

surface. To eliminate this gap, move the

micrometric lever one step up or down to

lower or raise the door by one centimetre.

Make a complete closing run and ensure

that the release lever is free from the

safety lever.

NB: the safety lever releases the

emergency release (CMS or C002) only

when the door is closed.





Safety lever

Release lever

White opening crown

Red closing crown

Microswitch of end-stop in closing

Microswitch of end-stop in opening

End-stop spring

Micrometric lever

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

5.10 Adjusting end-stops with encoder

Before beginning to make adjustments

on the end-stop, execute the run calibra-

tion procedure described in the technical

manual of the command board.

After calibrating, the door must be in a

closed position and the crown wheel on

the motor unit must be positioned to the

left.

Raise the end-stop spring unhooking it

from the support bracket and lower it

onto the crown wheel.

Important! For gearmotors installed on

sliding and folding doors, never unhook

the end-stop spring from the support

bracket.

Ensure that the release lever is free from

the safety lever.

NB: the safety lever releases the

emergency release (CMS or C002) only

with the door closed.

Important! For gearmotors installed on

sliding and folding doors, remove the

security lever and respective spring.

Crown wheel

End-stop spring

Support bracket

Safety lever

Release lever

Safety

lever

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

1) After completing assembly and electrical connections, make a hole with

a Ø 13 mm bit in the cover in the point indicated.

5.11 Assembly cover

2) Anchor the cover with the four screws provided.

3) Insert the release handle into the hole and fasten it with the washer

and the screw.

CAME

#!-%

5.12 Manual actuating device

5.13 Emergency release

Manually-operated winch for sectional doors (optional).

A chain-operated device for opening and closing the sectional door, it can be used both when

the automation is either horizontal or vertical.

Devices for releasing the ratiomotor by personalised wrench (CMS)

or with lever complete with suspended-cord transmission (C002).

C002

CMS

#!-%

C001

#!-%

All the data and information contained herein is considered subject to change at any time and at our discretion

ENGLISH

This unit requires no speciﬁ c maintenance. Only as a precautionary measure and in the case of intensive use is it rec-

ommended that you periodically check (6 months) the electric cable connected to the motor, the chain tension, and the bolts and

screws; you can also grease the sliding points between the ﬁ xed and mobile parts.

All checks must be recorded (in a dedicated record-book).

6 Maintenance

In its premises, CAME CANCELLI AUTOMATICI S.p.A. implements an Environmental Management System certiﬁ ed in

compliance with the UNI EN ISO 14001 standard to ensure environmental protection.

Please continue our efforts to protect the environment—which CAME considers one of the cardinal elements in the development

of its operational and market strategies—simply by observing brief recommendations as regards disposal:

DISPOSAL OF PACKAGING – The packaging components (cardboard, plastic, etc.) are all classiﬁ able as solid urban waste

products and may be disposed of easily, keeping in mind recycling possibilities.

Prior to disposal, it is always advisable to check speciﬁ c regulations in force in the place of installation.

PLEASE DISPOSE OF PROPERLY!

PRODUCT DISPOSAL – Our products are made up of various types of materials. Most of them (aluminium, plastics, iron,

electrical wires, etc.) may be disposed of in normal garbage collection bins and can be recycled by disposing of in speciﬁ c re-

cyclable material collection bins and disposal in authorized centres. Other components (electrical boards, remote control batteries,

etc.), however, may contain polluting substances. They should therefore be removed and given to qualiﬁ ed service companies for

proper disposal.

Prior to disposal, it is always advisable to check speciﬁ c regulations in force in the place of disposal.

PLEASE DISPOSE OF PROPERLY!

7 Demolition and disposal

MANUFACTURER’S DECLARATION

As per Enclosure II B of Machinery Directive 98/37/CE

Enclosed with the technical documentation (the original copy of the Declaration is available on request)

Date of the present declaration 07/12/2001

The representatives of

CAME Cancelli Automatici S.p.A.

via Martiri della Libertà, 15

31030Dosson di Casier - Treviso - ITALYtel

(+39) 0422 4940 - fax (+39) 0422 4941

internet: www.came.it - e-mail: [email protected]

Hereby declare, under their own respons ibility, that the product/s called ...

… comply with the Italian National Legal Provisions that transpose the

following Community Directives (where speciﬁ cally applicable):

ACHINERY DIRECTIVE 98/37/CE

OW VOLTAGE DIRECTIVE 73/23/EEC - 93/68/EEC

ECTROMAGNETIC COMPATIBILITY DIRECTIVE 89/336/EEC - 92/31/EEC

R&TTE D

IRECTIVE 1999/5/CE

Also, they furthermore represent and warrant that the product/s that are the subject of the present

Declaration are manufactured in the respect of the following main harmonized provisions:

EN 292

PART 1 AND 2 MACHINERY SAFETY.

EN 12453 INDUSTRIAL, COMMERCIAL AND OTHER CLOSING MECHANISMS.

EN 12445 I

NDUSTRIAL, COMMERCIAL AND OTHER CLOSING MECHANISMS.

EN 12978 S

AFETY DEVICES FOR POWER OPERATED DOORS AND GATES ....

EN 60335 - 1 SAFETY IN APPARATUSES FOR HOME USE.

EN 60204 - 1 MACHINERY SAFETY.

EN 61000 - 6 - 2 ELECTROMAGNETIC COMPATIBILITY.

EN 61000 - 4 - 4 E

LECTROMAGNETIC COMPATIBILITY.

EN 61000 - 4 - 5 E

LECTROMAGNETIC COMPATIBILITY.

IMPORTANT CAUTION!

It is forbidden to market/use product/s that are the subject of this declaration before completing and/or

incorporating them in total compliance with the provisions of Machinery Directive 98/37/CE

Signatures of the Representatives

TECHNICAL MANAGER

Mr. Gianni Michielan

MANAGING DIRECTOR

Mr. Paolo Menuzzo

CBX - CBXE - CBXE24 - CBXT - CBXET

CMS - CGP - CCT - CGIU - C001 - C002 - C003

C004 - C005 - C006 - C007 - C008

8 Manufacturer’s warranty

CAME UNITED KINGDOM LTD

UNIT 3, ORCHARD BUSINESS PARK TOWN

STREET, SANDIACRE

NOTTINGHAM - NG10 5BP - U.K.

Tel 0044 115 9210430

Fax 0044 115 9210431

CAME C-BXE24 Owner's manual

CAME C-BXE24 Owner's manual

CAME C-BXE24 Owner's manual

Related papers

Other documents