Designers Edge HEAT ZONE H-12000 User manual

Page is loading ...

2 Year Warranty on Fixture

(Does not apply to bulbs, which have no warranty)

Congratulations and Thank You from The Designers Edge!

The xture you have purchased should give you years of trouble free

service. We take pride in the design and construction of each of our

products and work to maintain the quality of our materials and

craftsmanship to assure your satisfaction.

This product is warranted to be free of defects in workmanship and

materials for a period of 2 years from the original date of purchase.

If any problems appear (other than burnt out bulbs, which carry no

warranty) within 2 years, the purchaser may return the item, freight

prepaid, together with a copy of your original purchase receipt to:

The Designers Edge

11730 NE 12th Street

Bellevue, WA 98005

Upon receipt of the item prepaid with a letter describing the problem,

and a check for $7.50 to cover return postage and handling, the

company will, at its option, either repair or replace the defective part or

xture at no charge to the purchaser. This warranty does not apply to

xtures that have been used for rental or commercial purposes. It does

not cover xtures that have been altered in any way or xtures that have

been subject to misuse, accidents or damage in transit.

IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES. NO CHARGES WILL BE ACCEPTABLE FOR

UNAUTHORIZED REPAIRS, PARTS OR SERVICE.

Some states do not allow limitations on how long an implied warranty

lasts and do not allow exclusions or limitations of incidental damages,

so parts or all of this warranty limitations or exclusions may not apply to

you. Legal warranty rights will vary from state to state and you may have

other rights.

ENGLISH

IMPORTANT NOTICE:

Every attempt has been made to deliver a quality product that will give you years of trouble free service.

In the event that you have problems with the xture, please DO NOT RETURN TO PLACE OF PURCHASE.

PLEASE CALL THE NUMBER BELOW FOR BULB OR PARTS PROBLEMS:

(425) 637-9601

8-5 pm (West Coast time). All warranty problems are handled

directly through The Designers Edge.

www.designersedge.com

H-12000_inst.indd 2 5/20/08 9:37:08 AM

Safety Instructions

• Please read all instructions carefully prior to using The Designers Edge

patio heater.

•

designed for indoor use only.

• Check that your main supply voltage is the same as voltage indicated

on unit.

• Disconnect power during installation and during lamp replacement.

• Check mounting plate to make sure heater is securely fastened in

place.

•

CAUTION - The lamp is HOT. Make sure it is cool before replacing.

• Keep out of reach of children. Lamp gets extremely hot during

operation.

• Do not use an extension cord with heater. Do not let cord come in

contact with heater during operation.

• For use on 15 amp circuit breaker only.

•

on and allow to cool before re-lamping.

ENGLISH

WARNING

Before using this heater read all warnings and instructions: LAMP GETS HOT!

ALLOW TO COOL BEFORE RE-LAMPING

H-12000_inst.indd 3 5/20/08 9:37:08 AM

Installation Notes

1. Disconnect power before installation and when re-lamping.

2. If you are unfamiliar with installing electrical xtures contact a qualied

electrician to install

3. Securely fasten mounting bracket to the xture.

4. Do not attempt to relocate xture when hot.

5. Minimum distance from side wall is 5’

6. Keep out of reach of children.

Lamp Replacement

1. Disconnect power supply and make sure lamp and xture are not hot.

2. Unscrew the screws at the top of the housing.

3. Open hinged cover, remove the lamp by pushing one end into it’s

holder and pulling the other end towards you.

WARNING: Do not handle lamp with your bare hands as the oil from

your hands will cause premature failure of the lamp.

CAUTION, before using this appliance:

Check that the voltage indicated on the type plate

corresponds to the mains supply voltage.

• Ensure that the heater has been securely fastened

in its nal mounting position.

• Unplug and turn o power switch during

installation, cleaning and/or replacing the

emitter. Always ensure that the emitter is cool.

• Do not handle the halogen heat emitter with

bare hands.

• Do not use an extension cable with this product.

• Keep the power cable away from the body of the heater as it will get hot

during use.

• Ensure that children do not tamper with the heater.

• Do not insert any object through any slot or opening in the heater.

ENGLISH

H-12000_inst.indd 4 5/20/08 9:37:08 AM

• Use only on 15 ampere branch circuit.

• Use with AC current only

• Do not place objects such as furniture, papers, clothes and curtains closer

than 5’ to the front of the heater and keep them away from the sides

and rear when the heater is plugged in.

• Avoid the use of an extension cord because the extension cord may over

CAUTION: RISK OF FIRE

Keep combustible materials such as furniture,

paper, clothes and curtains at least 5’ (1.5m) from the

front of the heater and away from the sides and rear.

TABLE 1: SPECIFICATION

INSTALLATION

WARNING: This appliance MUST be grounded.

If the supply cord becomes damaged, it must be replaced by the manu-

hazard. Otherwise, the plug should be connected to a socket indoors.

MOUNTING

1. Securely fasten the heater to the bracket arm using the nut and

bolt supplied

2. Mount bracket backplate to mounting surface with 3 screws provided

3. Mount the heater on to the backplate by inserting bracket arm into backplate.

4. Insert locking pin to connect arm with backplate

ENGLISH

Minimum mounting

8’2”

Minimum mounting

distance from ceiling

1’ 5

7

/8”

Minimum distance

from side wall when

ceiling mounted

5’

H-12000_inst.indd 5 5/20/08 9:37:08 AM

5. Insert screw into hole on top of bracket arm to secure

• The heater must be mounted in such a way that the halogen emitter does not slant

more than 4˚ from the horizontal.

• Plug power cord into wall socket

• Turn on switch to operate

• Allow the heater to cool before attempting to reposition or move. Never attempt

to move the heater while it is switched on.

surfaces when mounting.

ENGLISH

H-12000_inst.indd 6 5/20/08 9:37:16 AM

ENGLISH

Keep out of reach of children.

MAINTENANCE

In the event of heater failure please contact the retailer rst. For

spare parts and advice, please contact the manufacturer.

Disconnect the power before commencing any maintenance procedure including

cleaning.

To ensure optimal heat eectiveness, it is

recommended that after the heater has been

used approximately 80-100 hours, the front glass and the reector are wiped with

a lint-free cloth.

The heater is supplied with safety glass. In the

unlikely event that it should become cracked,

please contact the manufacturer for an immediate replacement.

REPLACING THE EMITTER

• Turn xture o and unplug to ensure that the heat emitter is not illuminated

and that the heater body and emitter are cool.

• Unscrew the back two screws at the top of the casing.

• Open the hinged front cover.

• Remove the heat emitter from the spring loaded holders by pushing one end

further into its holder and pulling the end that is free towards you.

• Ret in reverse order.

CAUTION: Do not handle the heat emitter

with bare hands. Finger marks will burn into

the quartz emitter causing premature emitter failure.

H-12000_inst.indd 7 5/20/08 9:37:16 AM

ENGLISH

IMPORTANT INSTRUCTIONS:

When using electrical appliances, basic precautions should always be

including the following:

1) Read all instructions before using this heater.

2) This heater is hot when in use . To avoid burns, do not let bare skin

touch hot surfaces. Allow heater to cool before relamping or moving.

Keep combustible materials, such as furniture, pillows, bedding, papers,

clothes and curtains at least 5 feet from the front of the heater and keep

them away from the sides and rear.

3) Extreme caution is necessary when any heater is used by or near

children or invalids and whenever the heater is left operating and unat-

tended.

4) Always unplug heater when not in use.

5) Do not operate any heater with a damaged cord or plug or after the

heater malfunctions, has been dropped or damaged in any manner.

Return heater to authorized service facility for examination, electrical or

mechanical adjustment, or repair.

6) For indoor use only

7) Never locate heater where it may fall into a bathtub or other water

container.

8) Do not run cord under carpeting. Do not cover cord with throw rugs,

where it will not be tripped over.

outlet.

10) Connect to properly grounded outlets only.

11) Do not insert or allow foreign objects to enter any ventilation or

the heater.

manner. Do not use on soft surfaces, like a bed, where openings may

become blocked.

H-12000_inst.indd 8 5/20/08 9:37:16 AM

13) A heater has Hot and arcing or sparking parts inside. Do not use it in

14) Use this heater only as described in this manual. Any other use not

injury to persons.

15) Avoid the use of an extension cord because the extension cord may

cord, the cord shall be no. 12 AWG minimum size and rated not less than

16) Disconnect xture from power source before relamping the xture.

1500 watts

SAVE THESE INSTRUCTIONS

This heater is for use on 120 volts. The cord has a plug as shown at A in

Figure 65.1. An adapter as shown at C is available for connecting three-

blade grounding-type plugs to two-slot receptacles. The green ground-

ing lug extending from the adapter must be connected to a permanent

ground such as a properly grounded outlet box. The adapter should not

be used if a three-slot grounded receptacle is available

ENGLISH

H-12000_inst.indd 9 5/20/08 9:37:18 AM

HEAT ZONE

MC

CHAUFFERETTE

USAGE

POUR PATIO

Modèle # H-12000

FRANÇAIS

H-12000_inst.indd 10 5/20/08 9:37:21 AM

Page is loading ...

Designers Edge HEAT ZONE H-12000 User manual

This manual is also suitable for

Designers Edge HEAT ZONE H-12000 User manual

in other languages

Other documents