Page is loading ...
®
INSTALLATION MANUAL
Glass Front Electric Radiant Heater
Model Linea
IP55
Content
1. Important 3
2. Introducon 4
3. Specicaon 4
4. Installaon 4
4.1 Mounng 4
4.2 Mounng hole centres 4
5. Heater Operaon 5
5.1 Heater display/control pod 5
5.2 Remote control handset 5
6. Maintenance 6
6.1 Remote control baery replacement 6
6.2 Replacing the lamp emier 6
6.3 Handling a replacement emier 6
6.4 Fing a new lamp emier 6
6.5 Recycling informaon 7
7. Spare parts 8
8. Wiring diagram 9
Declaraon of conformity 10
1. Important
When using Spaceray electric heaters, basic
precauons should always be followed to reduce the risk
of re, electric shock, and injury to persons, including the
following:
Read all instrucons before using this heater.
• Before using this appliance:
- Check that the voltage indicated on the type
plate corresponds to the mains supply voltage.
- Ensure that the heater has been securely
fastened in its nal mounng posion.
• Do not locate the heater immediately below a
socket outlet.
• This appliance can be used by children aged from
8 years and aboveand persons with reduced
physical, sensory or mental capabilies or lack
of experience and knowledge if they have been
given supervision or instrucon concerning use
of the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
• Children of less than 3 years should be kept away
unless connually supervised.
• Children aged from 3 years and less than 8 years
shall only switch on/o the appliance provided
that it has been placed or installed in its intended
normal operang posion and they have been
given supervision or instrucon concerning use
of the appliance in a safe way and understand the
hazards involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
• CAUTION Some parts of the product can become
very hot and cause burns. Parcular aenon has
been given where children and vulnerable people
are present.
• Disconnect pole switch from the hard wired circuit
during installaon, cleaning and/or replacing the
lamp emier and always ensure that the lamp
emier is cool.
• Do not use an extension cord with this product be-
cause the extension cord may overheat and cause
a risk of re.
• Keep the mains supply cord away from the body of
the heater which will get hot during use.
• Arrange the mains supply cord so it cannot be
tripped over or damaged.
• Do not cover or obstruct the heater while it is in
use.
• Do not insert any object through any slot or
opening in the heater.
• Do not use if a guard is not present.
• Do not install less than the minimum mounng
distance from the oor.
• WARNING: This heater should only be installed
indoors with a thermostat device to control the
room temperature and operated by users capable
of using the device. Do not use this heater in small
rooms when they are occupied by persons not
capable of leaving the room on their own, unless
constant supervision is provided.
• Do not touch the heater when it is turned on, as
the body gets hot.
• Do not use the heater in a bathroom, laundry
areas and similar locaons. Never locate the
heater where it may fall into a bathtub or other
water container.
• A heater has hot parts inside. Do not use it in
areas where petrol, paint, or ammable liquids are
used or stored.
• CAUTION: Do not direct a hose or spray water at
the heater or into any of its openings.
• WARNING: If the supply cord becomes damaged, it
must be replaced by the manufacturer, its service
agent or a similar qualied person in order to
avoid a hazard.
• WARNING: This appliance must be connected to a
supply that is earthed!
IMPORTANT:
SAVE THESE INSTRUCTIONS FOR FUTURE USE.
CAUTION!
CAUTION!
WARNING!
WARNING!
CAUTION!
WARNING!
IMPORTANT!
WARNING: RISK OF FIRE
Keep combusble material such as furniture,
papers, clothes and curtains 1.8m (6) from
the front of the heater and away from the
sides and rear.
If the heater is to be used outside, it is
recommend that a waterproof or indoor
socket outlet is used.
The Linea heater produces radiant heat like the sun,
warming people and objects rather than the air in
between. It is mounted on an adjustable bracket that
allows the heat to be directed exactly where it is required.
The heaters are designed for indoor and outdoor use.
future reference.
3.1 Dimensions
The Linea heater is ed with 3m of supply cable and a
3-pin plug. For permenent connecon it is unnecessary
to open the terminal wiring enclosure, in order to carry
out installaon of this product.
CAUTION: Please observe the minimum safe distance
between the heater body and any inammable surfaces.
CAUTION: Do not mount the heater on plasc sots and
fascia boards and ensure the mounng surface will
suitably withstand the radiant heat from the heater
body.
CAUTION: All installaons must be in accordance with
the latest electrical safety regulaons.
NOTE: When hard wiring, a large double pole switch with
a 3.0mm contact disconnecon should be ed.
NOTE: When installing the heater indoors it should be
connected to a suitable thermostat device.
NOTE: We recommend using a RCD where applicable.
The Linea heater should be wall mounted in a horizontal
(Fig. A) manner or ceiling suspended (Fig. C).
1. Securely fasten the heater brackets to the mounng
surface using the xing holes in the brackets. See Fig. D
over the page for mounng hole centers of the brackets.
Please refer to the specicaon table for recommended
posioning of the heater.
2. Fix in the required angular posion by ghtening the
xing bolts on the brackets at the rear of the heater (see
Fig. B).
3. Secure the supply cable so it is directed and secured
away from the heater and is not resng on the body or
obstrucng the air-vents.
Model LINS-024IP
kW 230V N & E 1Ph 50Hz
Power kW 2.4
Current A 10.4
Current per phase (minimum) A 15.5 (L1)
IP 55
Weight kg 6.7
192mm
1002mm
96mm
126mm
Use MCB type 3 or C
CAUTION!
CAUTION!
CAUTION!
NOTE:
NOTE:
NOTE:
CAUTION
Always isolate the heater from the mains supply when
mounng or adjusng the heater posion.
Fig. A
Fig. C
Face down mounng ONLY.
DO NOT ANGLE
Fig. B
• CAUTION: When wall mounng the heater, do not
posion the heater at an angle more than 90° or
less then 45° as shown in Fig. A.
• CAUTION: The heater should be mounted with
the minimum clearances adhered to. Please refer
to the specicaon table for the recommended
posioning of the heater. Do not install the heater
in a corner!
• CAUTION: Always allow the heater to cool before
aempng to reposion/move.
• Never aempt to move the heater while it is
switched on!
• CAUTION: Observe the minimum safe distance
between the heater body and inammable
surfaces and objects when mounng (see
specicaon table).
• CAUTION: Do not angle heater when mounted
to a ceiling with wall brackets. Extended ceiling
brackets are available. Please contact Spaceray for
details.
NOTE: The brackets on the back of the heater can be
posioned to allow for narrow mounng surfaces such as
pillars and poles (permanently xed).
If a bracket is moved from one end, the bracket at the
opposite end should also be moved the same i.e. 2 in
from the le, 2 in from the right to keep the heater bal-
anced.
CAUTION! Ensure the spring washers are retained under
the screw heads holding the body brackets and always
fully ghten the screws! If any of the fasteners get lost or
damaged, please contact Spaceray for replacements.
CAUTION: Only operate the heater with the remote
handset when you have a clear view of the heater to
ensure there are no obstrucons or hazards on, in front
of or around the heater.
CAUTION: Switch o/disconnect from the mains power
supply when not in use.
CAUTION: Do not let children play with the remote
control handset.
Switch the heater on (I) and o (O) by the rocker switch
at the right hand side end of the heater. Red light ashes
when power on (standby).
5.2 Remote control handset
T+ - Press repeatedly to increase the
run back mer in 5 minute increments
up to 100 minutes (displays 99) green
light indicates mer acve and heater
switches o when countdown lapses.
P+ - Press repeatedly to increase the
power level of the heater up to 100%
Hi.
P1 70% - Shortcut buon to select 70%
power output of the heater which is a
popular seng.
CAUTION!
CAUTION!
CAUTION!
CAUTION!
CAUTION!
Fig. D
CAUTION!
NOTE:
CAUTION!
CAUTION!
CAUTION!
- press to turn the heater
(default is P1 aer power o).
P- - Press repeatedly to decrease the
power level ohe heater down to 30%
(displays F1).
T- - Press repeatedly to decrease the
run back mer in 5 minute Increments
- pressing down to zero will deacvate
the run back mer.
P2 100% - Shortcut buon to select
full power output of the heater.
6. Maintenance
In the event of heater failure, or for spare parts or
advice, please contact your distributor in the rst
instance.
• Disconnect from the mains before commencing any
maintenance procedure including cleaning.
• To ensure opmum heat eecveness, it is
recommended that that the guard and lamp emier
are removed and the reector is wiped with a lint
free cloth before reassembling should the reector
show considerable signs of dust or dirt.
The remote control can accept a CR2025 or CR2032
baery although it is recommended that a CR2032
baery is used for longer baery life.
A baery is supplied with the
remote and needs ng before
use.
Note. Baery must go under wire
contact as shown on the right.
It is very important that the replacement lamp emier is
exactly the same as the one it was supplied with. Failure
to t the exact same type could cause the heater to fail
or even become dangerous especially when used in an
outdoor environment.
Please contact your distributor to purchase your
replacement lamp emier and state the model number
of the heater you wish to t the lamp emier to.
CAUTION: Please ensure that the length of wires on the
replacement lamp emier are the same as shown in
Fig. E.
A new lamp emier should not be handled with
bare hands.
Remove nger marks with a so cloth and
methylated spirits or rubbing alcohol. Finger
marks will burn into the lamp emiers quartz
glass causing premature failure.
1. Ensure the heater and lamp emier are cool and the
power supply is disconnected from the hard wired
heater by disconnecng the large double pole switch.
2. Remove the 3 × large screws (Fig. H) from either side
of the main body (6 in total) taking care to retain the
spring washers and remove the front glass frame.
3. Remove the 4 x small screws as highlighted in Fig. I to
take out the side reectors and allow access to the
quick-t female/male connectors and the lamp emier
holding clips.
4. Gently separate the ‘lamp emier wires rubber
protecve connector covers’ from each other using a
twisng and pulling moon in the direcon arrowed in
CAUTION!
Fig. E
CAUTION
The mains power should be disconnected from the heater by
disconnecng the double pole switch before any aempts
are made to replace the lamp emier.
Please read the notes in secon 6.3 with regards to handling
and buying a replacement lamp emier, before proceeding
and we recommend you read through the following
procedure before commencing.
Fig. H
Fig. I
Fig. J to reveal the bullet connectors at either end of
the lamp emier wires (Fig. K).
5. Holding the two connector halves at the crimp points
as highlighted in Fig. K with long nose pliers -DO NOT
HOLD BY THE WIRES, gently pull apart in opposite
direcons as shown in Fig. L to separate the
connecon. Repeat at the opposite end of the lamp
emier.
6. One at a me pull the lamp emier holder spring clips
back in the direcon shown in Fig. M (over page) and
li up the ceramic caps of the lamp emier to remove
it from the heater.
7. The lamp emier should now be removed from the
heater. Ret the new lamp emier into the lamp
emier holders ensuring the ceramic caps are
correctly seated.
8. Ret the male and female bullet connectors by fully
pushing together (slight click) and cover with the
moveable protecon sleeves (reverse of steps 4 & 5).
9. Ret the side reector bracket/reectors (reverse of
step 3).
10. Ret front glass frame (reverse of step 2) ensuring
the spring washers are used under the screw heads.
11. The heater is now ready for to reconnect to the
mains power supply for use.
CAUTION! Do not touch the heater during operaon!
The use of this symbol indicates
that this product may not be
treated as household waste. By
ensuring this product is disposed
of correctly, you will help prevent
potenal negave consequences
for the environment and human
health, which could otherwise be
caused by inappropriate waste
handling of this product.
For more detailed informaon about recycling of this
product, please contact your local council or your
household waste disposal service.
Fig. J
Fig. K
Fig. L
Fig. M
CAUTION!
7. Spare parts
Item
A Heater body 1
BGlass frame 1
C Side reector 2
DLamp emier 1
E Body bracket 2
FMounng bracket 2
G M8 Pozi screw for glass frame 6
HM4 Pozi screw for side reector 4
IM8 Hex bolt for bracket 2
J M4 Pozi screw for body bracket 4
KM8 Nyloc nut 2
L M8 Plain washer 4
MM4 Spring washer for body bracket 4
N M6 Spring washer for glass frame 6
8. Wiring Diagram
Controller PCBA
DPDT Switch
230V - 50Hz
L N E
Brown
Blue
NOTES
FACTORIES: IPSWICH, ENGLAND - CHARLOTTE, N.C, U.S.A
Gas Fired Products (UK) Ltd
Chapel Lane
Claydon
Ipswich
Suolk, IP6 0JL
Tel: +44(0)1473 830 551
Fax: +44(0)1473 832055
www.spaceray.co.uk
info@spaceray.co.uk
®
Linea Manual December 2022
/
