Honda 08R80-MCH-300C User manual

Type
User manual

This manual is also suitable for

© 2004 American Honda Motor Co., Inc - All Rights Reserved. 08R80-MCH-3000-9C 1 of 8
Accessory Application Publications No.
Issue Date
Honda Dealer: Please give a copy of these instructions to your customer.
INSTALLATION
INSTRUCTIONS
TORQUE CHART
Tighten all screws, bolts and nuts to their specified torques.
Refer to the Service Manual for the tightening torques of
removed parts.
TOOLS REQUIRED
Socket (8 and 12 mm)
Ratchet
Box-end wrench (12 mm)
Torque wrench
CUSTOM WINDSHIELD
PERFORMANCE STYLE
P/N 08R80-MCH-300C
P/N 08R80-MCH-300G
VTX1800C/F
September 2004
USE AND CARE INFORMATION
When this windshield is dirty, rinse it thoroughly with
cool water to remove loose dirt, then wipe with a clean
cloth or sponge.
Do not use a brush to clean this windshield as it may
scratch the surface.
Never use petroleum solvents such as gasoline, thinner
or benzine to clean the windshield. Also do not use
acid or alkaline cleaners.
Wipe up spilled brake or battery fluid at once as they
may damage the plastic surface.
If the motorcycle is left covered for an extended period
of time, park in the shade. Parking a covered motorcycle
in direct sunlight can cause the windshield to deform
due to heat buildup under the cover.
Check the windshield mounts frequently and retighten
if necessary.
No. Description Qty
(1) Custom windshield 1
(2) Upper stay 1
(3) Lower stay 1
(4) 8 mm flange bolt 2
(5) 8 mm flange nut 2
(6) 6 mm SH flange bolt 4
(7) Washer 4
(8) Grommet 4
(9) Collar 4
(10) Meter visor 1
Item N·m kgf·m Ibf·ft
6 mm SH flange bolt 9 0.9 6.5
8 mm flange bolt and nut 26 2.7 20
(1)
(2)
(3)
(6)
(8)
(6)
(7)
(8)
(9)
(4)
(7)
(9)
Included in the P/N 08R80-MCH-300G
APPLICATION
P/N 08R80-MCH-300C: VTX1800C
P/N 08R80-MCH-300G: VTX1800F
(10)
(5)
PARTS LIST
2 of 8 08R80-MCH-3000-9C © 2004 American Honda Motor Co., Inc - All Rights Reserved.
INSTALLATION
1. Install the meter visor. (VTX1800F only)
METER VISOR
Remove the adhesive
backing before attaching.
ISOPROPYL ALCOHOL
Thoroughly clean the area
where the meter visor will be
attached.
2. Remove the bolts as shown.
3. Install the upper stay as shown.
UPPER STAY
TOP BRIDGE
HEADLIGHT
Side View
THROTTLE CABLES
Route the throttle cables, install the hose guide as shown.
UPPER STAY
BOLT (Reuse)
UPPER
STAY
8 mm FLANGE BOLT
BOLT (Reuse)
HOSE GUIDE
BOLT (Save)
BOLT (Reuse)
Only for motor-
cycles equipped
with the front fork
cover.
BOLT (Reuse)
Only for motor-
cycles equipped
with the front fork
cover.
© 2004 American Honda Motor Co., Inc - All Rights Reserved. 08R80-MCH-3000-9C 3 of 8
6. Install the grommets as shown.
WINDSHIELD STAY
GROMMET
Sectional View
GROMMET
WINDSHIELD
STAYS
GROMMET
CUSTOM WINDSHIELD
5. Install the lower stay as shown.
LOWER STAY
BOLT
(Reuse)
HEADLIGHT
8 mm FLANGE
NUTS
BOLT
(Reuse)
4. Remove the parts shown in the illustration.
BOLT
(Reuse)
NUT (Save)
BOLT
(Reuse)
4 of 8 08R80-MCH-3000-9C © 2004 American Honda Motor Co., Inc - All Rights Reserved.
7. Loosely install the custom windshield sub assembly
as shown.
8. Check that the custom windshield is positioned equally
on both sides, then tighten the bolts.
COLLAR
CUSTOM WINDSHIELD
UPPER STAY
LOWER STAY
HEADLIGHT
Equal distance on both sides.
COLLAR
6 mm SH
FLANGE BOLT
WASHER
CUSTOM WINDSHIELD
© 2004 American Honda Motor Co., Inc - Tous droits réservés. 08R80-MCH-3000-9C 7 of 8
6. Installer les rondelles isolantes, de la manière indiquée.
ARMATURE DE PRE-BRISE
RONDELLE ISOLANTE
Vue en coupe
RONDELLE
ISOLANTE
ARMATURES DE
PARE-BRISE
RONDELLE
ISOLANTE
PARE-BRISE PERSONNALISE
5. Installer l’armature inférieure, de la manière indiquée.
ARMATURE
INFERIEURE
BOULON
(Réutiliser)
PHARE
ECROU A COLLE-
RETTE DE 8 mm
BOULON
(Réutiliser)
4. Déposer les pièces indiquées dans l’illustration.
BOULON
(Réutiliser)
ECROU
(Garder)
BOULON
(Réutiliser)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Honda 08R80-MCH-300C User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages