Transition Networks S3230-1029-A1 Reference guide

ION System

Command Line Interface (CLI)

C1|S12|L1AP2|L2D>#### DEVICE A ###

C1|S12|L1AP2|L2D>show soam md

Local MD ID Name Level MAs MIPs Permission

-----------------------------------------------------------

1 UNIabMD 0 1 0 none

6 ProviderMD 6 1 0 none

C1|S12|L1AP2|L2D>show soam ma

MA index : 1

MD index : 1

MD level : 0

MD name : UNIabMD

MA name : UNIabUntagged

CCM interval : 1s

MEPs : 1

MEP ID list : (2 MepIds) 10 20

Permission : defer

VLAN ID list : none

Auto detection timeout : 4000

Auto detect remote MEP : disabled

Reference Manual

33461 Rev. E

2 33461 Rev. E http://www.transition.com/

Trademarks

All trademarks and registered trademarks are the property of their respective owners.

Copyright Notice/Restrictions

No part of this work may be reproduced or used in any form or by any means (graphic, electronic or

mechanical) without written permission from Transition Networks.

Printed in the U.S.A.

ION System CLI Reference Manual for x323x Remotely Managed NID

33461 Rev. E

Contact Information

Transition Networks

10900 Red Circle Drive

Minnetonka, MN 55343 USA

Tel: 952- 941-7600 or 1-800-526-9267

Fax: 952-941-2322

Revision History

Rev Date Description

A 08/11/10 Revised for firmware version 1.0.3.

B 12/22/10

Revised for firmware version 1.0.5. New features include Circuit ID support, L2CP support, Redundancy

enhancements, SNMP v1/v2c setting, and Web Interface enhancements.

C 05/13/11

Revised for ION Rel. 1.0.0, Hardware Rev. 0.0.1, and Bootloader Rev. 1.2.1.

New features include 1) ION T1/E1 (x6010) and DS3 (x6210) support, 2) Configuration of IONMM Ethernet

ports, 3) Syslog function, 4) Backup and restore of SOAM config and IONPS card, 5) SSH web interface

cleanup, 6) Port mode / MAC Learning Enable portlist, 7) TNDP Enable/Disable, 8) Flush VLAN FID/DB, and 9)

Updated Help files.

D 12/05/11

Revised for ION Rel. 1.2.1 with: 1) Increase Rate Limiting Options. 2) SNMPv3 support.

3) BOOTP IP Addressing support. 4) Strict Priority Queuing support. 5) Serial File Transfer

(X/Y/Zmodem) commands support. 6) Password can be changed using the community write

string, and any login or password that is not fixed. 7) When using SSH client to login to ION, both

the userid (root) and password (TNIONAdmin1) are not fixed. 8) Minor enhancements to SSH

package 9) Fixed MEF-related bugs.

E 04/05/12 Revised for v1.3.1 with IPv6, TACACS+ and Auto Provisioning support.

http://www.transition.com/ 33461 Rev. E 3

Table of Contents

General.......................................................................................................................................................... 5

Documentation Conventions......................................................................................................................... 6

Related Manuals ....................................................................................................................................... 7

Commands Affect on Stored Files............................................................................................................ 8

Command Line Editing ............................................................................................................................ 9

Display Similar Commands ................................................................................................................. 9

Partial Keyword Lookup ...................................................................................................................... 9

Recall Commands ................................................................................................................................ 9

Keystroke Commands ........................................................................................................................ 10

Command Matrix ........................................................................................................................................ 11

System Commands...................................................................................................................................... 37

System User / Login Commands ................................................................................................................ 66

ACL Commands ......................................................................................................................................... 69

ACL Commands (IPv4).......................................................................................................................... 71

ACL Commands with IPv6 .................................................................................................................... 78

Backup / Restore (Provision) Commands................................................................................................... 85

Bandwidth Commands................................................................................................................................ 88

DMI Commands.......................................................................................................................................... 91

Dot1bridge Commands ............................................................................................................................... 93

Dot1dbridge Commands ............................................................................................................................. 95

Ethernet Port Commands ............................................................................................................................ 97

Forwarding Database (FDB) Commands.................................................................................................. 119

HTTPS Commands ................................................................................................................................... 125

IP / DNS / DHCP Commands................................................................................................................... 128

LPT Commands ........................................................................................................................................ 138

LOAM (Link OAM) Commands .............................................................................................................. 141

MAC Learning Portlist Commands .......................................................................................................... 152

Performance / RMON Statistics................................................................................................................ 154

QoS Commands ........................................................................................................................................ 156

RADIUS Commands ................................................................................................................................ 162

Redundancy Commands (Fiber Port)........................................................................................................166

Serial File Transfer Protocol (X/Y/Zmodem) Commands........................................................................ 168

SNMP Commands .................................................................................................................................... 171

SNMP v3 Commands - Alphabetical List ............................................................................................172

SNTP Commands...................................................................................................................................... 185

SOAM (Service OAM) Commands.......................................................................................................... 193

SOAM Restrictions...............................................................................................................................193

SOAM Initialization Commands .............................................................................................................. 194

SOAM Maintenance Domain (MD) Commands ...................................................................................... 196

SOAM Maintenance Association (MA) Commands ................................................................................ 199

SOAM Management Entity Group (MEG) Commands............................................................................204

SOAM Maintenance End Point (MEP) Commands.................................................................................. 210

MEP Loopback Commands.................................................................................................................. 217

MEP Link Trace Commands ................................................................................................................ 219

MEP Frame Loss Measurement Commands ........................................................................................221

MEP Delay Measurement..................................................................................................................... 223

MEP ETH-TEST Commands ............................................................................................................... 225

SOAM Maintenance Intermediate Point (MIP) Commands..................................................................... 228

4 33461 Rev. E http://www.transition.com/

SSH Commands........................................................................................................................................233

System Logging (Syslog) Commands....................................................................................................... 238

TACACS+ Commands ............................................................................................................................. 242

TNDP Commands..................................................................................................................................... 249

TFTP Transfer / Upgrade Commands....................................................................................................... 250

Upgrade / Update Firmware Commands .................................................................................................. 253

VLAN Commands .................................................................................................................................... 258

Management VLAN Commands .......................................................................................................... 259

VLAN Device-Level Commands ......................................................................................................... 261

VLAN Port-Level Commands.............................................................................................................. 265

VLAN Database Device-Level Commands.......................................................................................... 268

Technical Support ..................................................................................................................................... 272

Recording Model Information and System Information.......................................................................273

Appendix A: CLI Command Summary .................................................................................................... 275

ION CLI Commands via the help Command (C1|S7|L1D>?).............................................................. 275

ION CLI Commands via the list Command (C1|S8|L1D>list)............................................................. 277

Appendix B: Web Interface vs. CLI Commands ......................................................................................287

Appendix C: CLI Messages and Recovery ...............................................................................................300

SNMP Messages................................................................................................................................... 355

Basic Recovery Steps....................................................................................................................... 355

Syslog Messages and Sys.log Output ................................................................................................... 382

Syslog Messages .............................................................................................................................. 382

Sample Sys.log Output..................................................................................................................... 385

TFTP Server Messages..................................................................................................................... 388

Appendix D: Linux Commands ................................................................................................................389

Glossary .................................................................................................................................................... 393

Index ......................................................................................................................................................... 457

Tables

Table 1: Documentation Conventions........................................................................................................... 6

Table 2: Command Line Editing................................................................................................................. 10

Table 3: CLI Command Matrix .................................................................................................................. 11

Table 4: User Level Rights via Web / CLI ................................................................................................. 66

Table 5: Ethernet Port Feature Compatibility ............................................................................................. 97

Table 6: Timezones................................................................................................................................... 188

http://www.transition.com/ 33461 Rev. E 5

General

This manual describes the USB and Telnet command line interface (CLI) commands available for ION

System chassis or standalone x323x Remotely Managed Multiport NID operations. This manual is for

experienced network administrators who are responsible for configuring and maintaining the ION system.

CLI offers the most comprehensive set of management features. CLI is used during the initial setup (set

IPs etc.) and troubleshooting, but can also be used for day-to-day management (device management,

firmware upgrades, managing security features, etc.).

This manual documents the following models:

 C3230 OAM/IP-Based Remotely-Managed NID

 C3230 OAM/IP-Based Remotely-Managed NID (with DMI support)

 C3230 OAM/IP-Based Remotely-Managed NID (single fiber products)

 C3231 OAM/IP-Based Remotely-Managed NID (two open SFP slots)

 S3230 OAM/IP-Based Remotely-Managed NID

 S3230 OAM/IP-Based Remotely-Managed NID (with DMI support)

 S3230 OAM/IP-Based Remotely-Managed NID (single fiber products)

 S3231 OAM/IP-Based Remotely-Managed NID (two open SFP slots)

IMPORTANT

CLI commands are case sensitive. Enter the CLI commands as shown.

In order to execute the commands described in this manual, you must press the Enter key after the

command has been entered.

General

http://www.transition.com/ 33461 Rev. E 6

Documentation Conventions

The conventions used within this manual for commands/input entries are described in the table below.

Table 1: Documentation Conventions

Convention Meaning

Boldface text

Indicates the entry must be made as shown. For example:

ipaddr=<addr>

In the above, only ipaddr= must be entered exactly as you see it, including the

equal sign (=).

< >

Arrow brackets indicate a value that must be supplied by you. Do not enter the

symbols < >. For example:

ipaddr=<addr>

In place of <addr> you must enter a valid IP address.

[ ]

Indicates an optional keyword or parameter. For example:

go [s=<xx>]

In the above, go must be entered, but s= does not have to be.

{ } |

Indicates that a choice must be made between the items shown in the braces. The

choices are separated by the | symbol. For example:

state={enable | disable}

Enter state=enable or state=disable.

“ ”

Indicates that the parameter must be entered in quotes. For example:

time=<“value”>

Enter time=”20100115 13:15:00”.

>

Indicates a selection string. For example:

Select File > Save.

This means to first select/click File then select/click Save.

General

7 33461 Rev. E http://www.transition.com/

Related Manuals

The ION system and related manuals are listed below.

1. ION System 32xx NID User Guide, 33432

2. ION Management Module (IONMM) User Guide, 33457

3. ION System CLI Reference Manual, 33461 (this manual)

4. ION219-A 19-Slot Chassis Installation Guide, 33412

5. IONMM Management Module Install Guide, 33420

6. ION Dry Contact Relay (DCR) Kit Install Guide, 33422

7. IONPS-A AC Power Supply Install Guide, 33423

8. IONPS-D DC Power Supply Install Guide, 33424

9. IONPS-A ION AC Power Supply Install Guide, 33464

10. ION ADP PointSystem Card Adapter for ION Chassis 33413

11. E-MCR-05 Media Converter Rack User’s Guide, 33392

12. SFP Modules (model specific)

13. Release Notes (software version specific)

14. Product Documentation Postcard, 33504

Note: This manual may provide links to third part web sites for which Transition Networks is not

responsible. Information in this document is subject to change without notice. All information was

deemed accurate and complete at the time of publication. This manual documents the latest

software/firmware version. While all examples may not display the latest version number, all of the

descriptions and procedures reflect the latest software/firmware version, noted in the Revision History on

page 2.

General

http://www.transition.com/ 33461 Rev. E 8

Commands Affect on Stored Files

IMPORTANT

Certain CLI commands affect important stored files. Doing a reboot, restart or upgrade of the

IONMM, a power restart of the chassis, or a reset to factory remove temporary files (e.g. configuration

backup files, Syslog file). A Factory Reset also removes the permanent settings (e.g. configuration files,

HTTPS certification file, SSH key.

These CLI commands can cause a loss of files:

 reboot - cold start the system.

 reset - reset factory configuration.

 restart - restart ACL

 upgrade - upgrade firmware modules

See the specific command description for additional information.

General

9 33461 Rev. E http://www.transition.com/

Command Line Editing

This section describes how to enter CLI commands.

A CLI command is a series of keywords and arguments. Keywords identify a command, and arguments

specify configuration parameters.

Display Similar Commands

At the command line, you can use the key or the ? key to show available commands in a category

of commands after entering a part of the command.

For example, use the key to enter part of the command (show ether in this example) to display all

of the available commands that start with show ether. The commands display in a single row.

C1|S7|L1D>show ether <tab key>

config loopback security statistics tdr

Use the ? key after a partial CLI command entry to display all of the available commands that start with

show ether, but in a single column:

C1|S7|L1D>show ether ?

config

loopback

security

statistics

tdr

Partial Keyword Lookup

If you terminate a partial keyword with a question mark, alternatives that match the initial letters are

provided. (Remember to not leave a space between the command and question mark.) For example “s?”

shows all the keywords starting with “s.”

Recall Commands

To recall recently-entered commands from the command history, perform one of the optional actions

below:

Ctrl-P or Up arrow (↑) key: Recall commands in the history buffer, beginning with the most recent

command. Repeat the key sequence to recall successively older commands.

Ctrl-N or Down arrow (↓) key: Return to more recent commands in the history buffer after recalling

commands with Ctrl-P or the Up arrow key. Repeat the key sequence to recall successively more recent

commands.

General

http://www.transition.com/ 33461 Rev. E 10

Keystroke Commands

The table below shows the optional keystrokes available to edit command lines (*indicates HyperTerm

support, ** indicates command prompt support, *** indicates both HT and command prompt support by

this keystroke).

Table 2: Command Line Editing

Capability Keystroke Purpose

Move the command line around

to make changes or corrections

Ctrl-B *** or

left (←) arrow key *** Move the cursor back one character

Ctrl-F *** or

right (→) arrow key ***

Move the cursor forward one

character

Ctrl-A ***

Move the cursor to the beginning of

the command line

Ctrl-E ***

Move the cursor to the end of the

command line

Recall commands from the

buffer and paste them in the

command line

Ctrl-Y *** Recall the most recent entry in the

buffer

Ctrl-T **

Transpose the character to the left of

the cursor with the character located

at the cursor

Ctrl-Y **

Recall the most recent entry in the

buffer

Delete entries (if you make a

mistake or change your mind)

Delete key *** or

Backspace key ***

Erase the character to the left of the

cursor

Ctrl-D *** Delete the character at the cursor

Ctrl-K ***

Delete all characters from the cursor

to the end of the command line

Ctrl-U *** or

Ctrl-X ***

Delete all characters from the cursor

to the beginning of the command line

Ctrl-W ***

Delete the word to the left of the

cursor

Esc D **

Delete from the cursor to the end of

the word

Capitalize or lowercase words or

capitalize a set of letters Esc C *

Change case from capital to lower-

case (or lower-case to capital) at the

cursor

Redisplay the current command

line if the switch unexpectedly

sends a message to your screen

Ctrl-L ***

or Ctrl-R ***

Redisplay the current command line

(reverse-i-search)

http://www.transition.com/ 33461 Rev. E 11

Command Matrix

The table below lists all of the CLI commands and categories, and indicates if the command applies to the

IONMM, other NIDs, or both.

Note: CLI commands are case sensitive. Enter the CLI commands as shown.

Table 3: CLI Command Matrix

System Commands IONMM NIDs

Login Password for Access x x

Log Out (Quit) x x

Clear the Screen x x

Go Back to IONMM x x

Go to Another Location x x

Help x x

List x x

Ping x x

Ping6 x x

Reboot x x

Reset Factory Configuration x x

Reset System Uptime x x

Set USB Port State x x

Command Matrix

http://www.transition.com/ 33461 Rev. E 12

Show USB Port State x x

Slot Power On / Power Off / Reset (PS) (PS)

Set Current Time x x

Set Debug Level x x

Set Power Relay State (PS) (PS)

Set PS Sensor Notification / Relation / Severity / Value (PS) (PS)

Set System Contact x x

Set System Location x x

Set System Name x x

Show Card Information x x

Show Card Type x x

Show Chassis Information x x

Show Device Mode x x

Show Power Supply Configuration x

Show Slot Information x x

Show System Information x x

Switch Device Mode x x

Set Circuit ID x

Command Matrix

13 33461 Rev. E http://www.transition.com/

Show Circuit ID x

ACL Commands IONMM NIDs

Add a New ACL Condition x x

Add a New ACL Rule x x

Add IPv6 Tables ACL Condition Type x x

Add IPv6 Tables ACL Rule Index

Add IPv6 Tables ACL Rule Position x x

Remove ACL Conditions x x

Remove ACL Rules x x

Remove IPv6 Tables ACL Condition x x

Remove IPv6 Tables ACL Condition All x x

Remove IPv6 Tables ACL Rule x x

Remove IPv6 Tables ACL Rule All x x

Restart ACL x x

Restart IPv6 Tables ACL x x

Set ACL State x x

Set ACL Chain Default Policy x x

Command Matrix

http://www.transition.com/ 33461 Rev. E 14

Set Certain Conditions to a Rule x x

Set IPv6 Tables ACL Condition / Rule Index x x

Set IPv6 Tables ACL Rule / Traprate x x

Set IPv6 Tables ACL State x x

Set IPv6 Tables ACL Table / Chain / Policy x x

Set IPv6 Tables ACL Table x x

Set Trap Rate of a Rule x x

Show ACL State x x

Show All ACL Conditions x x

Show All ACL Rules x x

Show All IPtable Chain Definitions x x

Show IP6 Tables ACL Chain x x

Show IP6 Tables ACL Condition x x

Show IP6 Tables ACL Rule x x

Show IP6 Tables ACL State x x

Command Matrix

15 33461 Rev. E http://www.transition.com/

Backup / Restore Commands IONMM NIDs

Backup x

Restore x

Set Backup / Restore Module Index x

Show Modules x

Bandwidth Commands IONMM NIDs

Set Bandwidth Rate Limiting Mode x

Set Bandwidth Rate Limit x

DMI Commands IONMM NIDs

Show DMI Configuration x

Set DMI Receive Power Preset Level x

Command Matrix

http://www.transition.com/ 33461 Rev. E 16

Dot1bridge / Dot1dbridge Commands IONMM NIDs

Add Dot1bridge Port x

Assign Dot1bridge Name x

Remove Dot1bridge x

Remove Dot1bridge Port x

Set Dot1bridge Aging Time x

Set Dot1bridge Community x

Show Dot1bridge Aging Time x

Show Dot1dbridge IEEE-Tag Priority Remapping x

Show Dot1dbridge IP-TC Priority Remapping x

Command Matrix

17 33461 Rev. E http://www.transition.com/

Ethernet Port Commands IONMM NIDs

Clear Ethernet Port Counters x

Reset All Ports Counters x

Set Ethernet Port L2CP Configuration x

Show Ethernet Port L2CP Configuration x

Set Ethernet Port Admin Status x

Set Ethernet Port Advertisement Capability x

Set Ethernet Port AutoCross x

Set Ethernet Port Auto-Negotiation Status x

Set Ethernet Port Duplex x

Set Ethernet Port Far End Fault x

Set Ethernet Port Filter 802.1Q Tagged Non-Mgmt Frames x

Set Ethernet Port Filter 802.1Q Untagged Non-Management

Frames

x

Set Ethernet Port Loopback Type x

Set Ethernet Port Pause Frames x

Set Ethernet Port Source MAC Address Lock x

Set Ethernet Port Source MAC Address Lock Action x

Command Matrix

http://www.transition.com/ 33461 Rev. E 18

Set Ethernet Port Speed x

Set Port Admin Mode (Ethernet PHY Mode) x

Show Ethernet Port Configurations x

Show Ethernet Port Loopback Capability x

Show Ethernet Port Loopback Running Status x

Show Ethernet Port Security Configuration x

Show Ethernet Port TDR Test Configuration x

Show Ethernet Port TDR Test Result x

Start/Stop Ethernet Port Loopback Operation x

Start Ethernet Port TDR Test x

Show Ethernet Statistics x

Firmware Upgrade Commands IONMM NIDs

Show Firmware Database Update Results x

Show Firmware Upgrade Results x

Show Upgrade File Name x

Update Firmware Database x

Upgrade Device Firmware x

Command Matrix

19 33461 Rev. E http://www.transition.com/

Forwarding Database Commands IONMM NIDs

Add Forwarding Database Entry x

Remove a Single Forwarding Database Entry x

Remove All Forwarding Database Entries x

Set Forwarding Database Connection Port x

Set Forwarding Database Entry Type x

Set Forwarding Database Priority x

Set Forwarding Portlist x

Set Forwarding Port Management Access x

Show Forwarding Database Configuration x

Show Forwarding Database Ports x

Command Matrix

http://www.transition.com/ 33461 Rev. E 20

HTTPS Commands IONMM NIDs

Set HTTPS Certificate File x x

Set HTTPS Certificate Type x x

Set HTTPS Port Number x x

Set HTTPS Private Key File x x

Set HTTPS Private Key File Password x x

Set HTTPS State x x

Show HTTPS Configuration x x

Start HTTPS Certificate Operation x x

IP/DNS/DHCP Commands IONMM NIDs

Set DCHP Client State x x

Set DNS Server Number / Type / Address x x

Set IP Type / Address / Subnet Mask x x

Set Gateway Type / Address x x

Set IP Address Mode x x

Set IP Management State x x

Show IP Configuration x x

Page is loading ...

Transition Networks S3230-1029-A1 Reference guide

This manual is also suitable for

Transition Networks S3230-1029-A1 Reference guide

Related papers

Other documents