2. Hampton Bay
  3. HD181430

Hampton Bay HD181430 Operating instructions

  • Hello! I've reviewed the Assembly & Installation Instructions for the Ceiling Fixture. This document provides step-by-step guidance on safely assembling and installing your new decorative fluorescent ceiling fixture, covering everything from wiring to securing the fixture. I'm ready to help answer any questions you may have about the instructions or the device itself!
  • What should I do before starting the installation?
    What should I do if I am not familiar with electrical wiring?
    How do I secure the fixture pan to the outlet box?
DECORATIVE FLUORESCENT CEILING FIXTURE
Fig. 1
ASSEMBLY & INSTALLATION INSTRUCTIONS
Please read carefully and save this instruction sheet, as you may need them at a
later date.
Turn off the main power at the circuit breaker before installing the fixture, in
orde
r
to
p
reven
t
p
ossible shoc
k
.
CAUTION Fig. 2
p
p
All electrical connections must be in accordance with local and national
electrical code (N.E.C) standards. If you are unfamiliar with proper electrical
wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that
no
parts
are
missing
by
the
illustrations
on
the
installation
instruction
GENERAL
1. Separate the METAL FRAME (16) and DIFFUSER (17) from the FIXTURE PAN
(10).
2. Pull the power supply wires out from the OUTLET BOX (1). Thread both FIXTURE
SCREWS
(
13
)
onto
the
OUTLET
BOX
.
no
parts
are
missing
by
the
illustrations
on
the
installation
instruction
.
ASSEMBLY AND INSTALLATION
SCREWS
(
13
)
onto
the
OUTLET
BOX
.
3. Make the wiring connections: connect the HOUSE GROUND WIRE (2) to the
FIXTURE GROUND WIRE (3); connect the WHITE SUPPLY WIRE (4) to the
WHITE FIXTURE WIRE (5); connect BLACK SUPPLY WIRE (6) to the BLACK
FIXTURE WIRE (8) using WIRE CONNECTORS (7). Carefully tuck all wires back
into the OUTLET BOX.
4. Carefully tuck all wiring back into the OUTLET BOX. Locate the FIXTURE PAN
ove
r
the OUTLET BOX
,
p
ositionin
g
the FIXTURE SCREW heads throu
g
hthelar
g
e
,
pg
g
g
openings of the key hole slots. Slide the FIXTURE PAN to seat the screws, and
tighten securely. (See Fig. 2)
5. Attach the T9 SOCKET (12) to the LAMP CONNECTOR (14). Attach the
CIRCLINE LAMP (15) to the FIXTURE PAN by pulling a LAMP BRACKET (11)
backward and inserting the CIRCLINE LAMP. Pull back the remaining LAMP
BRACKETS and insert the CIRCLINE LAMP. Follow the wattage label located on
the fixture body. Do not exceed the recommend wattage. 1. OUTLET BOX
2. HOUSE GROUND WIRE 10. FIXTURE PAN
11. LAMP BRACKET
6. Lay the DIFFUSER onto the METAL FRAME. Locate the METAL FRAME over
the FIXTURE PAN, aligning the SPRING CLIPS (18) with the notches located at the
edge of the FIXTURE PAN. Push the METAL FRAME against the FIXTURE PAN
and twist it clockwise about 1/8 of a turn so that the SPRING CLIPS slide onto the
FIXTURE PAN ledge.
INSTALLATION IS COMPLETE
3. FIXTURE GROUND WIRE
4. WHITE SUPPLY WIRE
5. WHITE FIXUTE WIRE
6. BLACK SUPPLY WIRE
7. WIRE CONNECTOR
8. BLACK FIXTURE WIRE
9. ELECTRONIC BALLAST
12. T9 SOCKET
13. FIXTURE SCREW
14. LAMP CONNECTOR
15. CIRCLINE LAMP
16. METAL FRAME
17. DIFFUSER
18. SPRING CLIP
/