Elkay DEMR233224 Installation guide

Elkay
Brand
Elkay
Model
DEMR233224
Category
Kitchen sinks
Type
Installation guide

Elkay DEMR233224 is a top mount double bowl sink made of #22 gauge, type 301 series, nickel-bearing stainless steel. It features a large bowl with an 8" depth and a 3" vertical and 2-3/4" horizontal radius coved corner, and a small bowl with a 5-1/8" depth and a 3" vertical radius coved corner. The exposed surfaces are polished to an elite satin finish, and the underside is fully undercoated. The sink comes with four faucet holes and a 3-1/2" drain opening. It complies with ASME A112.19.3-2008 / CSA B45.

Elkay DEMR233224 is a top mount double bowl sink made of #22 gauge, type 301 series, nickel-bearing stainless steel. It features a large bowl with an 8" depth and a 3" vertical and 2-3/4" horizontal radius coved corner, and a small bowl with a 5-1/8" depth and a 3" vertical radius coved corner. The exposed surfaces are polished to an elite satin finish, and the underside is fully undercoated. The sink comes with four faucet holes and a 3-1/2" drain opening. It complies with ASME A112.19.3-2008 / CSA B45.

G
Elkay
2222 Camden Court
Oak Brook, IL 60523
Printed in U.S.A.
©2011 Elkay
(Rev. 6/11)
2-9G
elkayusa.com
In keeping with our policy of continuing product improvement, Elkay reserves the right to change
product specifications without notice.
This specification describes an Elkay product with design, quality and functiona lbenefits to the
user. When making a comparison of other producers’ offerings, be certain these features are not
overlooked.
U-Channel Type Mounting System
SEE NEXT PAGE FOR PRODUCT DIMENSIONS.
OPTIONAL ACCESSORIES
Bottom Grid: GBG2115SS
Cutting Board: CB1516 (large bowl), CBS715 (small bowl),
CB816 (small bowll)
Drain: LK35, D1125
C
DE prefix sinks are listed by the International Association
of Plumbing and Mechanical Officials as meeting the
requirements of the Uniform Plumbing Code and the
National Plumbing Code of Canada.
ENERAL
Sink is formed of #22 gauge (DE prefix), or #20 gauge (DSE
prefix), type 301 series,nickel-bearing stainless steel.Top mount.
DESIGN FEATURES
Bowl Depth: 8" (203mm) (large bowl) DSE Series, 6-1/2" (165mm)
(large bowl) DE Series; 5-1/8" (130mm) (small bowl).
Coved Corners: 3" (76mm) vertical (small bowl) and 2-3/4" (70mm)
(large bowl) horizontal radius.
Finish: Exposed surfaces are polished to an elite satin finish.
Underside: Fully undercoated.
OTHER
Drain Opening: 3-1/2" (89mm).
NOTE: Unless otherwise specified, sink is furnished with 4
faucet holes as shown.
Sinks comply with ASME A112.19.3-2008 / CSA B45.4-08.
Model DSEMR23322R
Dayton
®
Elite Double Bowl Sink
Models DEMR23322, DEMR23322R,
DSEMR23322 and DSEMR23322R
SPECIFICATIONS
Model DSEMR23322
SINKS ARE
MADE IN THE USA
Elkay
2222 Camden Court
Oak Brook, IL 60523
Printed in U.S.A.
©2011 Elkay
(Rev. 6/11)
2-9G
elkayusa.com
SPECIFICATIONS
*
Length is left to right. Width is front to back.
SINK DIMENSIONS (INCHES)*
Model
DEMR23322
Model
DEMR23322R
Model DSEMR23322 Model DSEMR23322R
Dayton
®
Elite Double Bowl Sink
Models DEMR23322, DEMR23322R,
DSEMR23322 and DSEMR23322R
21"
(533mm)
33"
(838mm)
22"
(559mm)
15-3/4"
(400mm)
7-1/2"
(191mm)
3" R
(76mm)
3" R
(76mm)
3" R
(76mm)
3" R
(76mm)
21"
(533mm)
33"
(838mm)
22"
(559mm)
15-3/4"
(400mm)
7-1/2"
(191mm)
Model D(S)EMR233224 Illustrated
Model D(S)EMR23322R4 Illustrated
Hole Drilling Configurations
1-1/2
"
(38mm) Diameter Faucet Holes on 4
"
(102mm) Centers
3
4
5
3
4
3
4
3
4
5
4"
(102mm)
4"
(102mm)
L W L W D L W D L W
DEMR23322
33
(838mm)
22
(559mm)
7½
(191mm)
15¾
(400mm)
5⅛
(130mm)
21
(533mm)
15¾
(400mm)
6½
(165mm)
32⅜
(822mm)
21⅜
(543mm)
3, 4, or 5
36
(914mm)
DEMR23322R
33
(838mm)
22
(559mm)
21
(533mm)
15¾
(400mm)
6½
(165mm)
7½
(191mm)
15¾
(400mm)
5⅛
(130mm)
32⅜
(822mm)
21⅜
(543mm)
3, 4, or 5
36
(914mm)
DSEMR23322
33
(838mm)
22
(559mm)
7½
(191mm)
15¾
(400mm)
5⅛
(130mm)
21
(533mm)
15¾
(400mm)
8
(203mm)
32⅜
(822mm)
21⅜
(543mm)
3 or 4
36
(914mm)
DSEMR23322R
33
(838mm)
22
(559m
m)
21
(533mm)
15¾
(400mm)
8
(203mm)
7½
(191mm)
15¾
(400mm)
5⅛
(130mm)
32⅜
(822mm)
21⅜
(543mm)
3 or 4
36
(914mm)
Model Number
Overall
Left
Right
Inside Each Bow l
No. of 1½"
(38mm) Dia.
Faucet Holes 4"
(102mm) Centers
Minimum
Cabinet Size
Cutout in
Countertop (1½"
(38mm) Radius
Corners)
  • Page 1 1
  • Page 2 2

Elkay DEMR233224 Installation guide

Elkay
Brand
Elkay
Model
DEMR233224
Category
Kitchen sinks
Type
Installation guide

Elkay DEMR233224 is a top mount double bowl sink made of #22 gauge, type 301 series, nickel-bearing stainless steel. It features a large bowl with an 8" depth and a 3" vertical and 2-3/4" horizontal radius coved corner, and a small bowl with a 5-1/8" depth and a 3" vertical radius coved corner. The exposed surfaces are polished to an elite satin finish, and the underside is fully undercoated. The sink comes with four faucet holes and a 3-1/2" drain opening. It complies with ASME A112.19.3-2008 / CSA B45.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents