AFG 7.3AU Owner's manual

7.3AR

Read the BIKE GUIDE before using this OWNER’S MANUAL.

Lire le GUIDE D’UTILISATION DU VÉLO D’EXERCICE avant de se servir du présent MANUEL DU PROPRIÉTAIRE.

Lea la GUÍA DEL USUARIO DE LA BICICLETA ESTACIONARIA antes de usar este MANUAL DEL PROPIETARIO.

EXERCISE BIKE OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE DU VÉLO D’EXERCICE

MANUAL DEL PROPIETARIO DE LA BICICLETA ESTACIONARIA

7.3AU

AFG14_7.3AR_AU_OM_r1_5.indd 1 5/12/14 11:12 AM

Page is loading ...

3

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an exercise product, basic precautions should always be followed, including the following: Read all instructions

before using this exercise bike. It is the responsibility of the owner to ensure that all users of this exercise bike are adequately

informed of all warnings and precautions. If you have any questions after reading this owner’s manual, contact Customer

Tech Support at the number listed on the back panel.

AFG14_7.3AR_AU_OM_r1_5.indd 3 5/12/14 11:12 AM

4

READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS

EXERCISE BIKE. IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY

INSTRUCTIONS.

 CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult

your physician before continuing.

 Use this exercise bike for its intended purpose as described in this manual. Do not use attachments that have not been

recommended by the manufacturer.

 Never operate the exercise bike if it is not working properly, or if it has been damaged. Contact Customer Tech Support or

the authorized dealers for examination and repair.

 Do not use the exercise bike without proper footwear. NEVER operate the exercise bike with bare feet.

 Do not wear any clothing that might catch on any moving parts of this exercise bike.

 Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.

 Do not dismount the exercise bike until the pedals are at a complete STOP.

 Do not attempt to ride the exercise bike in a standing position at high RPMs until you have practiced at slower speeds.

 Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other

potentially moving part of the exercise bike.

 Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Customer

Tech Support or the authorized dealers.

 Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

 Close supervision is necessary when used near children, invalids or disabled people.

 When the exercise bike is in use, young children and pets should be kept at least 3 meters / 10 feet away.

 Ensure that adjustment levers (seat and handlebar fore-and-aft) are properly secured and do not interfere with range of

motion during exercise.

 This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive

harm.

WARNING

AFG14_7.3AR_AU_OM_r1_5.indd 4 5/12/14 11:12 AM

5

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the

assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed

correctly, the exercise bike could have parts that are not tightened and will seem loose and may cause irritating noises. To

prevent damage to the exercise bike, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your exercise bike’s serial number and enter it in the space

provided below. The serial number will be located on a white sticker with a bar code.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOX BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.

MODEL NAME: AFG EXERCISE BIKE

WARNING

SERIAL NUMBER:

SERIAL NUMBER LOCATION

AFG14_7.3AR_AU_OM_r1_5.indd 5 5/12/14 11:12 AM

6

CRANK

WATER BOTTLE HOLDER

PULSE GRIP HANDLEBARS

REAR STABILIZER TUBE POWER CORD SOCKET

CONSOLE

SEAT POSITION ADJUSTMENT KNOB

SEAT POST TUBE

SEAT HEIGHT ADJUSTMENT KNOB

FRONT STABILIZER TUBE

SEAT

PEDALS

SHROUD

CONSOLE MAST

CONSOLE MAST GROMMET

7.3AU

AFG14_7.3AR_AU_OM_r1_5.indd 6 5/12/14 11:12 AM

7

7.3AR

CRANK

WATER BOTTLE HOLDER

PULSE GRIP HANDLEBARS

RE AR STABILIZER TUBE

CONSOLE MAST HANDLEBARS

POWER CORD SOCKET

CONSOLE

SEAT SLIDE

SEAT POSITION ADJUSTMENT LEVER

FRONT STABILIZER TUBE

MESH SEAT BACK

SEAT BASE

PEDALS

FRONT SHROUD

CONSOLE MAST

CONSOLE MAST GROMMET

AFG14_7.3AR_AU_OM_r1_5.indd 7 5/12/14 11:12 AM

8

TOOLS INCLUDED:

F 13/15mm Flat Wrench

F Phillips Screwdriver/Allen Wrench

PARTS INCLUDED:

F 1 Bike Frame

F 1 Console

F 1 Console Mast

F 1 Console Mast Grommet

F 1 Front Stabilizer Tube

F 1 Rear Stabilizer Tube

F 1 Seat

F 1 Mesh Seat Back (7.3AR only)

F 1 Seat Back Bracket (7.3AR only)

F 1 Seat Back Bracket Plate (7.3AR only)

F 1 Seat Post Tube (7.3AU only)

F 1 Seat Post Bracket (7.3AU only)

F 1 Handlebar Bracket Cover (7.3AU only)

F 1 Pulse Grip Handlebars

F 2 Pedals with Straps

F 1 Water Bottle Holder

F 1 Audio Adapter Cable

F 1 Power Cord

F 1 Hardware Kit

UNPACKING

Unpack the product where you will be using it. Place the bike carton

on a level flat surface. It is recommended that you place a protective

covering on your floor. Never open box when it is on its side.

If you have questions or if there are any missing parts, contact

Customer Tech Support. Contact information is located on the

back panel of this manual.

NEED HELP?

PRE ASSEMBLY

 During each assembly step, ensure that ALL nuts and bolts

are in place and partially threaded. It is recommended you

complete the full assembly of your unit before completely

tightening any ONE bolt.

 Several parts have been pre-lubricated to aid in assembly and

usage. Please do not wipe this off. If you have difficulty, a light

application of lithium bike grease is recommended.

IMPORTANT NOTES

AFG14_7.3AR_AU_OM_r1_5.indd 8 5/12/14 11:12 AM

9

ASSEMBLY

7.3AR

page 16

7.3AU

page 16

AFG14_7.3AR_AU_OM_r1_5.indd 9 5/12/14 11:12 AM

10

7.3AR ASSEMBLY STEP 1

A Open HARDWARE FOR STEP 1.

B Attach the FRONT STABILIZER TUBE (1) to the

BIKE FRAME (2) using 2 BOLTS (A), 2 FLAT

WASHERS (B), 2 SPRING WASHERS (C) and

2 NUTS (D).

C Attach the REAR STABILIZER TUBE (3) to the

BIKE FRAME (2) using 2 BOLTS (A), 2 FLAT

WASHERS (B), 2 SPRING WASHERS (C) and

2 NUTS (D).

2

1

D

C

B

3

A

7.3AR

HARDWARE FOR STEP 1

PART TYPE QTY

A BOLT 4

B FLAT WASHER 4

C SPRING WASHER 4

D NUT 4

AFG14_7.3AR_AU_OM_r1_5.indd 10 5/12/14 11:12 AM

11

7.3AR ASSEMBLY STEP 2

A Open HARDWARE FOR STEP 2.

B Slide CONSOLE MAST GROMMET (4) from the

bottom up the CONSOLE MAST (5).

C Attach CONSOLE CABLES (6) and carefully tuck

all cables into BIKE FRAME (1). Slide CONSOLE

MAST (5) into BIKE FRAME (1).

D Attach the CONSOLE MAST (5) using 4 BOLTS

(E), 4 SPRING WASHERS (C) and 4 FLAT

WASHERS (B) from the rear.

E Slide CONSOLE MAST GROMMET (4) down over

BIKE FRAME (1).

1

5

4

6

B

C

E

7.3AR

NOTE: Be careful not to pinch any wires while attaching the console mast.

HARDWARE FOR STEP 2

PART TYPE QTY

E BOLT 4

B FLAT WASHER 4

C SPRING WASHER 4

AFG14_7.3AR_AU_OM_r1_5.indd 11 5/12/14 11:12 AM

12

7.3AR ASSEMBLY STEP 3

* NOTE: There is no hardware for this step.

A Attach PEDAL STRAPS (7) to PEDALS (8).

B Attach the RIGHT PEDAL to the RIGHT CRANK

ARM, tightening it CLOCKWISE with the provided

13mm/15mm flat wrench.

C Attach the LEFT PEDAL (8) onto the LEFT

CRANK ARM (9), tightening it COUNTER-

CLOCKWISE with the provided 13mm/15mm flat

wrench. (NOTE: The left crank arm is reversed

threaded so it is very important that it is tightened

counter-clockwise. Tightening it the opposite way

can damage the pedal or the crank arm or both.)

D Connect the CONSOLE CABLES (6) and carefully

tuck them into the CONSOLE MAST (5).

E Attach the CONSOLE (10) to the CONSOLE

MAST (5) using the 4 PRE-ATTACHED SCREWS

(11) (The screws will have to be removed from the

console first).

10

7

8

11

5

9

8

6

7.3AR

NOTE: Be careful not to pinch any wires while attaching the console.

AFG14_7.3AR_AU_OM_r1_5.indd 12 5/12/14 11:12 AM

13

7.3AR

7.3AR ASSEMBLY STEP 4

15

5

I

F

12

C

B

14

13

E

C

L

A Open HARDWARE FOR STEP 4

B To attach the SEAT BACK BRACKET (12) to the

SEAT FRAME (13), insert 2 BOLTS (F), 2 SPRING

WASHERS (C) and 2 FLAT WASHERS (B) into

the rear-facing screw holes on the SEAT BACK

BRACKET (12).

C Attach the HANDLEBARS (14) to the front-facing

screw holes on the SEAT BACK BRACKET (12)

using 2 BOLTS (E), 2 SPRING WASHERS (C) and

2 ARC WASHERS (L).

D Attach the WATER BOTTLE HOLDER (15) to the

CONSOLE MAST (5) using 2 SCREWS (I).

HARDWARE FOR STEP 4

PART TYPE QTY

F BOLT 15 MM 2

B FLAT WASHER 2

C SPRING WASHER 4

E BOLT 50 MM 2

L ARC WASHER 2

I SCREW 2

AFG14_7.3AR_AU_OM_r1_5.indd 13 5/12/14 11:12 AM

14

16

13

B

J

7.3AR ASSEMBLY STEP 5

7.3AR

A Open HARDWARE FOR STEP 5

B Attach the SEAT (16) to the SEAT FRAME (13)

using 4 BOLTS (J) and 4 FLAT WASHERS (B).

HARDWARE FOR STEP 5

PART TYPE QTY

J BOLT 4

B FLAT WASHER 4

AFG14_7.3AR_AU_OM_r1_5.indd 14 5/12/14 11:12 AM

15

7.3AR ASSEMBLY STEP 6

A Open HARDWARE FOR STEP 6.

B Place SEAT BACK BRACKET PLATE (17) on the

inside of the mesh seat back mount. Align mesh

SEAT BACK (18) to SEAT BACK BRACKET (12).

C Attach mesh seat back to seat back bracket using

3 BOLTS (K) and 3 FLAT WASHERS (B) from the

rear and 3 FLAT WASHERS (B) and 3 NUTS (H)

on the other side of the seat back bracket plate.

D Attach SEAT CABLE (19) as shown. Plug in

POWER ADAPTER (20) as shown.

K

19

B

17

12

18

H

20

7.3AR

7.3AR ASSEMBLY COMPLETE!

HARDWARE FOR STEP 5

PART TYPE QTY

K BOLT 3

B FLAT WASHER 6

H NUT 3

AFG14_7.3AR_AU_OM_r1_5.indd 15 5/12/14 11:13 AM

16

7.3AU ASSEMBLY STEP 1

A Open HARDWARE FOR STEP 1.

B Attach the FRONT STABILIZER TUBE (1) to the

BIKE FRAME (2) using 2 BOLTS (A), 2 FLAT

WASHERS (B), 2 FLAT WASHERS (C) and

2 NUTS (D).

C Attach the REAR STABILIZER TUBE (3) to the

BIKE FRAME (2) using 2 BOLTS (A), 2 FLAT

WASHERS (B), 2 FLAT WASHERS (C) and

2 NUTS (D).

1

2

D

C

B

A

3

7.3AU

HARDWARE FOR STEP 1

PART TYPE QTY

A BOLT 4

B FLAT WASHER 4

C SPRING WASHER 4

D NUT 4

AFG14_7.3AR_AU_OM_r1_5.indd 16 5/12/14 11:13 AM

17

7.3AU ASSEMBLY STEP 2

* NOTE: There is no hardware for this step.

A Attach SEAT (4) to SEAT BASE (5) using 3

PRE-INSTALLED FLAT WASHERS AND

NUTS (6).

B Attach SEAT BASE (5) to SEAT POST

TUBE (7) using SEAT ADJUSTMENT

KNOB AND WASHER (8).

C Pull the SEAT HEIGHT ADJUSTMENT

KNOB (9) outward while sliding the SEAT

POST TUBE (7) into the BIKE FRAME (2).

7

8

6

5

4

2

9

7.3AU

AFG14_7.3AR_AU_OM_r1_5.indd 17 5/12/14 11:13 AM

18

7.3AU ASSEMBLY STEP 3

7.3AU

NOTE: Be careful not to pinch any wires

while attaching the console mast.

A Open HARDWARE FOR STEP 3.

B Slide CONSOLE MAST GROMMET (10) from the

bottom up the CONSOLE MAST (11).

C Attach CONSOLE CABLES (12) and carefully tuck

all cables into BIKE FRAME (2). Slide CONSOLE

MAST (11) into BIKE FRAME (2).

D Attach the CONSOLE MAST (11) using 4 BOLT

(F), 4 SPRING WASHERS (C) and 4 FLAT

WASHERS (B) from the rear.

E Slide CONSOLE MAST GROMMET (10) down

over BIKE FRAME (2).

2

12

10

F

C

B

11

HARDWARE FOR STEP 3

PART TYPE QTY

F BOLT 4

B FLAT WASHER 4

C SPRING WASHER 4

AFG14_7.3AR_AU_OM_r1_5.indd 18 5/12/14 11:13 AM

19

7.3AU ASSEMBLY STEP 4

A Open HARDWARE FOR STEP 4.

B Feed the HANDLBAR WIRES (13) through the

hole in the CONSOLE MAST (11) and out the top

of the CONSOLE MAST (11).

C Attach the HANDLEBARS (14) to the CONSOLE

MAST (11) using 4 BOLTS (G), 4 SPRING

WASHERS (C) and 4 FLAT WASHERS (B).

D Attach the HANDLEBAR COVER (15) to the

CONSOLE MAST (11) using 2 SCREWS (H).

E Attach the WATER BOTTLE HOLDER (16) to the

CONSOLE MAST (11) using 2 SCREWS (H).

11

13

14

B

C

G

11

H

16

15

H

t

7.3AU

NOTE: Be careful not to pinch any wires

while attaching the handlebars.

HARDWARE FOR STEP 4

PART TYPE QTY

G BOLT 4

B FLAT WASHER 4

C SPRING WASHER 4

H SCREW 4

AFG14_7.3AR_AU_OM_r1_5.indd 19 5/12/14 11:13 AM

20

7.3AU ASSEMBLY STEP 5

7.3AU

* NOTE: There is no hardware for this step.

A Attach the RIGHT PEDAL (17) to the RIGHT

CRANK ARM (18), tightening it CLOCKWISE with

the provided 13mm/15mm flat wrench.

B Attach the LEFT PEDAL onto the LEFT CRANK

ARM, tightening it COUNTER-CLOCKWISE with

the provided 13mm/15mm flat wrench. (NOTE: The

left crank arm is reversed threaded so it is very

important that it is tightened counter-clockwise.

Tightening it the opposite way can damage the

pedal or the crank arm or both.)

C Connect the CONSOLE CABLES (12) and

carefully tuck them into the CONSOLE MAST (11).

D Attach the CONSOLE (19) to the CONSOLE

MAST (11) using the 4 PRE-ATTACHED SCREWS

(20) (The screws will have to be removed from the

console first).

E Plug in POWER ADAPTER (21) as shown.

17

21

20

18

12

19

11

7.3AU ASSEMBLY COMPLETE!

AFG14_7.3AR_AU_OM_r1_5.indd 20 5/12/14 11:13 AM

21

BIKE OPERATION

This section explains how to use your bike’s console and programming.

The BASIC OPERATION section in the BIKE GUIDE has instructions for the following:

 LOCATION OF THE BIKE

 POWER/GROUNDING INSTRUCTIONS

 SEAT POSITIONING

 MOVING THE BIKE

 LEVELING THE BIKE

 USING THE HEART RATE FUNCTION

AFG14_7.3AR_AU_OM_r1_5.indd 21 5/12/14 11:13 AM

Page is loading ...

AFG 7.3AU Owner's manual

This manual is also suitable for

AFG 7.3AU Owner's manual

in other languages

Related papers

Other documents