Yardistry Preston Pergola User manual

Brand: Yardistry

Model: Preston Pergola

Type: User manual

This manual is also suitable for

12 x 12 Preston Arched Roof Pergola

 1 support@yardistrystructures.com

HEIGHT:

8’2” or 2.49m

12 x 12 Pergola room

Installation and Operating Instructions – YM11635X

Yardistry – North America

Toll Free Customer Support: 1.888.509.4382

info@yardistrystructures.com

www.yardistrystructures.com

Yardistry / Selwood Products – Europe

Customer Support: +44 1284 852569

parts@selwoodproducts.com

www.selwoodproducts.com

Revised 12/22/2014

10’ (3.05 m)

12’ (3.66 m)

3.05 m (10’)

3.66 m (12’)

Retractable Sunshade Sold Separately

 2 support@yardistrystructures.com

Important Safety Notice!

Yardistrycomponentsareintendedforprivacy,decorativeandornamentaluseonly.

Product is NOT INTENDED for the following:

 •Asafetybarriertopreventunsupervisedaccesstopools,hottubs,spasorponds.

 •Asloadbearingsupportforabuilding,structure,heavyobjectsorswings.

 •Usedinstructuresthattrapwind,rainorsnowthatwouldcreateextraloadonthe

product.

Permanent structures may require a building permit. Asthepurchaserandorinstaller

ofthisproductyouareadvisedtoconsultlocalplanning,zoningandbuildinginspection

departmentsforguidanceonapplicablebuildingcodesand/orzoningrequirements.

Wood is NOT ame retardant and will burn.Grills,repitsandchimineasareare

hazardifplacedtooclosetoaYardistrystructure.Consultuser’smanualofthegrill,re

pitorchimneaforsafedistancesfromcombustiblematerials.

Wear gloves to avoid injuryfrompossiblesharpedgesofindividualelementsbefore

assembly.

During installation, follow all safety warnings provided with your tools and use

OHSA approved safety glasses.Somestructuresmayrequiretwoormorepeopleto

installsafely.

Check for underground utilities before digging or driving stakes into the ground!

General Information:WoodcomponentsaremanufacturedwithCedar(C.Lanceolata)

whichisprotectedwithfactoryappliedwater-basedstain.Knots,smallchecks(cracks)

andweatheringarenaturallyoccurringanddonotaffectthestrengthoftheproduct.

Annualapplicationofawater-basedwaterrepellentsealantorstainwillhelpreduce

weatheringandchecks.

www.yardistrystructures.com

Questions?

Calltollfreeorwriteusat:

1(888)509-4382

[email protected]

PatentsPending

General Information

 3 support@yardistrystructures.com

Limited Warranty

Yardistry warrants that this product is free from defect in materials and workmanship

for a period of one year from the original date of purchase. In addition, all lumber is

warranted for 5 years against rot and decay. This warranty applies to the original owner

and registrant and is non-transferable.

Regular maintenance is required to assure the integrity of your product and is a requirement of

the warranty. This warranty does not cover any inspection cost.

This Limited Warranty does not cover:

• Labor for replacement of any defective item(s);

• Incidental or consequential damages;

• Cosmetic defects which do not affect performance or integrity;

• Vandalism; improper use or installation; acts of nature;

• Actsofnatureincludingbutnotlimitedtowind,storms,hail,oods,excessivewater 

 exposure;

• Minor twisting, warping, checking, or any other natural occurring properties of wood that

do not affect performance or integrity.

Yardistryproductshavebeendesignedforsafetyandquality.Anymodicationsmadetothe

original product could damage the structural integrity of the product leading to failure and

possibleinjury.Yardistrycannotassumeanyresponsibilityformodiedproducts.Furthermore,

modicationvoidsanyandallwarranties.

This product is warranted for RESIDENTIAL USE ONLY. Yardistry disclaims all other

representations and warranties of any kind, express or implied.

This Warranty gives you specic legal rights. You may have other rights as well which vary from state to state or province to

province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of

consequential damages, and therefore this limitation may not apply to you.

 4 support@yardistrystructures.com

Instructions for Proper Maintenance

YourYardistrystructureisdesignedandconstructedofqualitymaterials.Aswithalloutdoor

productsitwillweatherandwear.Tomaximizetheenjoyment,safetyandlifeofyourstructure

itisimportantthatyou,theowner,properlymaintainit.

Symbols:

Throughouttheseinstructionssymbolsareprovidedinthetop,right-handcornerofthepage.

If you dispose of your Yardistry structure: Pleasedisassembleanddisposeofyour

unitsothatitdoesnotcreateanyunreasonablehazardsatthetimeitisdiscarded.Be

suretofollowyourlocalwasteordinances.

HARDWARE:

• Checkmetalpartsforrust.Iffound,sandandrepaintusinganon-leadpaintcomplying

with16CFR1303.

• Inspectandtightenallhardwareaftercompletionofassembly;afterrstmonthofuse;and

thenannually.Donotover-tightenastocausecrushingandsplinteringofwood.

• Checkforsharpedgesorprotrudingscrewthreads,addwashersifrequired.

WOODPARTS:

• Unprotectedtheywillappearweatheredovertime.Periodicapplicationofanexterior

waterrepellentorstain(water-based)willhelpimproveappearanceandlife.

• Checkallwoodmembersfordeterioration,structuraldamageandsplintering.Sanddown

splintersandreplacedeterioratedwoodmembers.Aswithallwood,somecheckingand

smallcracksingrainisnormal

• TapeMeasure

• CarpentersLevel

• StandardorCordlessDrill

• #2PhillipsBitorScrewdriver

• 7/16”WrenchorSocket

Assembly Guides

• 8’StepLadder

• SafetyGlasses

• AdultHelper

• Gloves

• HardHat

Tools Required:

• UseHelp,wherethisisshown,2or3people

arerequiredtosafelycompletethisstep.

Toavoidinjuryordamagetotheassembly

makesuretogetsomehelp.

• Useameasuringtapetoassureproper

location

• Pre-drillapilotholebeforefastening

screworlagtopreventsplittingofwood.

 5 support@yardistrystructures.com

Note: It is critically important you start with square, solid and level footings, concrete

pad or deck to attach your Pergola Room.

WesupplyRoomL-Mountswiththisstructurewhichgivesyoutheexibilitytopermanentlyinstallyour

structuretoapre-existingornewwoodorconcretesurface.

• ThehardwaretoattachtheRoomL-Mounttothestructureisincluded.

• Thehardwaretomountthestructurepermanentlywillneedtobepurchasedseparatelyatyourlocal

hardwarestore.

Ifyouaremountingtoconcretefootersseebelowforthecorrectlocationsandplacement.Pleasedouble

checkforpossibilityofanyundergroundutilitiessuchasgas,telephone,cableorsprinklerlines.

Followingaresomeexamplesofhowtomountthestructuretowoodorconcretesurfaces.

Refertoyourlocalbuildingandcitycodes,ordinances,neighbourhoodcovenants,orheightrestrictions

regardingthistypeofstructureforguidanceonaccepableinstallationrequirements.

Permanent Installation Examples

Concrete Footer

2 3/4” 1” 11/2”

To

Required

Depth

AnchoringHardwarenotincluded

#10x1-1/4”PanScrewsIncluded

16 1/8” - Groove

RoomL-Mount

PanelPost

CornerPost

PanelPost

RoomL-Mount

20 3/4"

169 11/16"

120"

78 1/2"

 6 support@yardistrystructures.com

Permanent Installation Examples cont.

Concrete Patio (min. 10’ 2” x 10’ 2”) with 12” clearance on all sides

Wood Deck (min. 10’ 2” x 10’ 2”) with 12” clearance on all sides

#10x1-1/4”PanScrewsIncluded

AnchoringHardwarenotincluded

RoomL-Mount

#10x1-1/4”

PanScrew

Post

 7 support@yardistrystructures.com

Trellis End 110-1/2" (300)

Long Plinth Assembly (033)

Beam End 10-1/2" (069)

hidden

Short Plinth B Assembly (034)

Beam End 34-1/4" (192)

hidden

Beam 20-3/4" (067)

End Plinth Assembly (032)

2 x 3 Trellis Clip

Arch Gusset Right (193)

Arch Beam Offset (080)

Arch Beam Front (195)

Arch Gusset Left (194)

Corner Post (190)

Corner Panel Assembly (024/025 Assembled)

Trellis End 33-1/2" (062)

L Mount Right

Beam 81-1/2" (301)

L Mount Left

Short Plinth A Assembly (035)

Arch Beam Center (079)

 8 support@yardistrystructures.com

Bottom Brace Insert 2 x 4 x 16-1/8" - Box 2

8pc. (191) -

38.1 x 69.9 x 408.9mm

Y50119-191

38.1 x 63.5 x 2806.7mm

9pc. (300) - Trellis End 110-1/2" 2 x 3 x 110-1/2" - Box 1

Y50119-300

4pc. (069) - Beam End 10-1/2" 2 x 6 x 10-1/2" - Box 3

Y50119-069

Y70119-024

Engineered Panel Corner Post 2 x 4 x 91" - Box 2

8pc. (025) -

53.5 x 69.9 x 2311.4mm

Y70119-025

36 x 69.9 x 2311.4mm

38.1 x 139.7 x 870.0mm

38.1 x 38.1 x 574.7mm

38.1 x 139.7 x 266.7mm

38.1 x 63.5 x 850.9mm

38.1 x 76.2 x 409.6mm

38.1 x 38.1 x 409.6mm

38.1 x 139.7 x 527.1mm

36 x 127 x 453.2mm

Part Identification ( )

Dimensions are approximate and are shown to assist in the identification of parts for

assembly. Actual dimensions may be smaller or larger.

32pc. (185) - Horizontal Insert 2 x 2 x 16-1/8" - Box 2

Y50119-185

64pc. - X Insert 2 x 2 x 22-5/8" - Box 3

Y50119-183

9pc. (062)- Trellis End 33-1/2" 2 x 3 x 33-1/2" - Box 1

Y50119-062

8pc. (189) - Cross Brace Insert 2 x 4 x 16-1/8" - Box 1

8pc. (024) - Engineered Panel Post 2 x 4 x 91" - Box 2

Y50119-189

4pc. (194) - Arch Gusset Left 2 x 5 x 17-27/32" - Box 1

Y50119-194

4pc. (193) - Arch Gusset Right 2 x 5 x 17-27/32" - Box 1/2

Y50119-193

4pc. (067) - Beam 20-3/4" 2 x 6 x 20-3/4" - Box 2

Y50119-067

4pc. (192) - Beam End 34-1/4" 2 x 6 x 34-1/4" - Box 1

Y50119-192

 9 support@yardistrystructures.com

Part Identification ( )

Dimensions are approximate and are shown to assist in the identification of parts for

assembly. Actual dimensions may be smaller or larger.

Arch Beam Offset 2 x 6 x120" - Box 1

2pc. (080) -

38.1 x 241.3 x 3048.0mm

Y50119-080

Arch Beam Front 2 x 6 x120" - Box 1

2pc. (195) -

38.1 x 241.3 x 3048.0mm

Y50119-195

Corner Post 3 x 3 x 91" - Box 2

4pc. (190) -

69.9 x 69.9 x 2311.4mm

Y50119-190

34.9 x 152.4 x 141.3mm

8pc. (032) - End Plinth Assembly - Box 2

Y70119-032

34.9 x 152.4 x 598.5mm

8pc. (033) - Long Plinth Assembly - Box 2

Y70119-033

34.9 x 152.4 x 492.1mm

4pc. (035) - Short Plinth A Assemlby - Box 2

Y70119-035

34.9 x 152.4 x 492.1mm

4pc. (034) - Short Plinth B Assembly - Box 2

Y70119-034

Arch Beam Center 2 x 6 x120" - Box 1

1pc. (079) -

38.1 x 241.3 x 3048.0mm

Y50119-079

38.1 x 139.7 x 2070.1mm

2pc. (301) - Beam 81-1/2" 2 x 6 x 81-1/2" - Box 1

Y50119-301

 10 support@yardistrystructures.com

8pc. - L Mount Right - (Y00419-005)

Hardware Identification ( )

Dimensions are approximate and are shown to assist in the identification of

parts for assembly. Actual dimensions may be smaller or larger.

16pc. - 1/4" Connector Nut

(Y08420-205)

2pc. - 3/16" Hex Key - (Y00400-003)

1pc. - 1/8" Drill Bit

(Y00400-002)1pc. - #2 x 2" Robertson Driver

(9200014)

9 pc. - 2 x 3 Trellis Clip - (Y00419-003)

32pc. - X-Insert Pin

(Y0814-001)

16pc. -5/16" Flat Washer

(Y05420-301)

8pc. - Wafer Bolt 1/4 x 3-3/4" - (Y07420-233)

96pc. - Trim Screw #6 x 30mm - (Y06420-910)

8pc. - L Mount Left - (Y00419-004)

9pc. - 1/4" Lock Nut

(Y08420-203)

8pc. - Wafer Bolt 1/4 x 4-1/4" - (Y07420-241)

9pc. - Wafer Bolt 1/4 x 2" - (Y07420-220)

50pc. - Pan Screw #10 x 1-1/4" - (Y06420-911) 98pc. - Wood Screw #10 x 4" - (Y06420-940)

144pc. - Wood Screw #8 x 3" - (Y06420-530)

48pc. - Wood Screw #8 x 2-1/2" - (Y06420-522)

 11 support@yardistrystructures.com

PRODUCTNUMBER:YM11635X

CARTONI.D.STAMP:_____________(Box1)

CARTONI.D.STAMP:_____________(Box2)

CARTONI.D.STAMP:_____________(Box3)

STOP STOPSTOP STOP

1-888-509-4382

[email protected]

C. Readtheassemblymanualcompletely,payingspecialattentiontoANSIwarnings;

notes;andsafety/maintenanceinformationonpages1-4.

 •Followtheinstructionsinorder.

•Thisstructureisdesignedtobeassembledandinstalledideallybytwopeople,

DONOTattempttoinstallalone.

 •Considertheslopeofelevationwhereyouplantoinstallthestructure.Also,checkfor

gas,telephone,otherutilitiesorsprinklerlinelocationspriortoexcavatinganyholes.

D. Beforeyoudiscardyourcartonsllouttheformbelow.



•ThecartonI.D.stampislocatedontheendofeachcarton.

 •Pleaseretainthisinformationforfuturereference.Youwillneedthisinformationifyou

contacttheConsumerRelationsDepartment.

•Eachstepindicateswhichboltsand/orscrewsyouwillneedforassembly,aswellas

anyatwashers,lockwashers,t-nutsorlocknuts.

A.Thisisthetimeforyoutoinventoryallyourhardware,woodandaccessories,

referencingthepartsidenticationsheets.Thiswillassistyouwithyourassembly.

Step 1: Inventory Parts - Read This Before Starting Assembly

B.Ifthereareanymissingordamagedpiecesoryouneedassistancewith

assemblypleasecontacttheconsumerrelationsdepartmentdirectly.Callus

beforegoingbacktothestore.

 12 support@yardistrystructures.com

Step 2: Assemble “X” Inserts

64 x X Insert 38.1 x 38.1 x 574.7 mm (2 x 2 x 22-5/8”)

HardwareWood Parts

Fig. 2.1

32 x X Insert Pin

A:PlaceoneXInsertPinintooneXInsert,thenattachasecondXInserttoformacompleteInsert.Makesure

thepiecesaretighttoeachother.

B:RepeatStepAtomake32completeInserts.

XInsertPin XInsert

 13 support@yardistrystructures.com

Step 3: Assemble 8 Panels

Part 1

HardwareWood Parts

Note: You will be assembling 8 Panel Post Assemblies in

total in Step 3.

A:Layone(024)EngineeredPanelPostandone(025)Engi-

neeredPanelCornerPostonedgesothegroovedsidesface

eachother,onalevelsurface.

B:Placeone(191)BottomBraceInsertinbetweentheposts

tighttothebottomledgeandattachwithtwo#8x3”Wood

Screwsasshowning.3.1.

C:SetoneHorizontalInsertbetweenthepostsandtightto

BottomBraceInsert.Attachwithtwo#8x3”WoodScrewas

showningure3.1.

32 x #8 x 3” Wood Screw

(024)

Engineered

PanelPost

8 x (024) Engineered Panel Post 36 x 69.9 x 2311.4 mm (2 x 4 x 91”)

8 x (191) Bottom Brace Insert 38.1 x 69.9 x 409.6 mm (2 x 4 x 16-1/8”)

8 x (185) Horizontal Insert 38.1 x 38.1 x 409.6 mm (2 x 2 x 16-1/8”)

8 x (025) Engineered Panel Corner Post 53.5 x 69.9 x 2311.4 mm (2 x 4 x 91”)

Fig. 3.1

(191)Bottom

BraceInsert

Tight to

bottom

ledge on

both posts

Top

Bottom

#8x3”Wood

Screws

#8x3”Wood

Screws

(025)Engineered

PanelCornerPost

(185)HorizontalInsert

 14 support@yardistrystructures.com

Hardware

Wood Parts

C:SlideonecompleteInsertinfrom

thetopofthepanelsanddowntothe

(185)HorizontalInsert.(g.3.2)

D:Slideone(185)HorizontalInsert

tothetopofthecompleteInsert.(g.

3.2)Attachwithtwo#8x3”Wood

Screws.

Note: Be sure to maintain 16”

measurement between each (185)

Horizontal Insert. (g 3.3)

E:RepeatStepsCandDsothereare

fourcompleteInsertsperPanelPost

assembly.Thelastboardshouldbe

a(189)CrossBraceInsert.Attachall

threeHorizontalInsertswithtwo#8x

3”WoodScrewsperinsertandattach

CrossBraceInsertwithfour#8x3”

WoodScrews.(g.3.3)

80 x #8 x 3” Wood Screw

(024)

Engineered

PanelPost

32 x Completed Inserts from Step 2

8 x (189) Cross Brace Insert 38.1 x 76.2 x 409.6 mm (2 x 4 x 91”)

24 x (185) Horizontal Insert 38.1 x 38.1 x 409.6 mm (2 x 2 x 91”)

Fig. 3.3

(185)

Horizontal

Insert

from top

in between

grooves

(189)Cross

BraceInsert

(185)

Horizontal

Insert

#8x3”Wood

Screwsx5

Fig. 3.2

Step 3: Assemble 8 Panels

Part 2

(185)

Horizontal

Insert

Complete

Insert

#8x3”Wood

Screwsx5

(025)

Engineered

PanelCorner

Post

(191)Bottom

Braceinsert

16”

 15 support@yardistrystructures.com

Step 4: Attach Panel Posts to Corner Posts

Part 1

Note: Only pre-drill one post per assembly

A:OnEngineeredPanelCornerPost,perassembly,pre-drilltwoholesfromtheinside,attheplacesshownin

g.4.1and4.2.Pre-drillinthecentreofthepanelandonaslightangle.

Fig. 4.2

Fig. 4.1

Pre-drill

on a slight

angle

(024)

Engineered

PanelPost (025)

Engineered

PanelCorner

Post

 16 support@yardistrystructures.com

Step 4: Attach Panel Posts to Corner Posts

Part 2

Hardware

Wood Parts

8 x #10 x 4” Wood Screw

24 x #8 x 2-1/2” Wood Screw

4 x (190) Corner Post 69.9 x 69.9 x 2311.4 mm (3 x 3 x 91”)

Fig. 4.3

B:Throughthepre-drilledholesattachtwo

PanelPostsassembliestoone(190)Corner

Postwithone#10x4”WoodScrewperPanel

PostAssemblyatbottomandsix#8x2-1/2”

WoodScrewsalongpostasshowning.4.3.

Startatthebottomandworkup.

Complete this step for all four Corner

Posts.

(190)

Corner

Post

#8x2-1/2”

Wood

Screws

#8x2-1/2”

Wood

Screws

#10x4”

Wood

Screws

#8x2-1/2”

Wood

Screws

Flush

 17 support@yardistrystructures.com

PG 55

A:Pre-drillwitha1/8”drillbitandattachtwoLMounts(oneLMountRightandoneLMountLeft)ushtothe

insideedge,atthebottomofeachPanelPostwithtwo#10x1-1/4”PanScrewperLMountasshowning.5.1,

5.2and5.3.

Step 5: Attach L - Mount Brackets

Fig. 5.1

Fig. 5.2

Hardware

16 x Room L-Mount (Right and Left)

32 x #10 x 1-1/4” Pan Screw

#10x1-1/4”

PanScrew

Flush to bottom of posts

x2perLMount

LMountLeft

LMountRight LMountLeft

LMountRight

Note orientation of tabs.

Fig. 5.3

LMountRight

LMountLeft

Note: Flush to the inside edge.

 18 support@yardistrystructures.com

Hardware

Wood Parts

#6x30mm

TrimScrew

(034)ShortPlinth

BAssembly

Plinths rest on top of the L Mounts

(035)ShortPlinth

AAssembly

Flushtocorners

Step 6: Attach Plinths to Corner Post Assembly

Part 1

A:Placeone(034)ShortPlinthBAssemblywithone(035)ShortPlinthAAssemblytighttoeachotherand

attachusingtwo#6x30mmTrimScrewattheoppositecornersperPlinth.(Fig.6.1and6.2)

Note:Plinthswillbeattachedtofourcorners.

Fig. 6.1

Fig. 6.2

16 x #6 x 30 mm Trim Screw4 x (035) Short Plinth A Assembly 34.9 x 152.4 x 492.1 mm

4 x (034) Short Plinth B Assembly 34.9 x 152.4 x 492.1 mm

 19 support@yardistrystructures.com

HardwareWood Parts

#6x30mm

TrimScrew

x2perboard



Flush

(033)

LongPlinth

Assembly

Step 6: Attach Plinths to Corner Post Assembly

Part 2

B:Ontheoutsideofthecornerpostassembly,placetwo(033)LongPlinthAssemblytightagainsteachother

using2#6x30mmTrimScrewsperPlinth.Besuretheyareushandtight.(Fig.6.3and6.4)

Fig. 6.3

Fig. 6.4

16 x #6 x 30 mm Trim Screw

8 x (033) Long Plinth Assembly 34.9 x 152.4 x 598.5 mm

 20 support@yardistrystructures.com

Hardware

Wood Parts

#6x30mm

TrimScrew

x4perboard



Flush

(032)End

Plinth

Assembly

Note: Loosen screws as

necessary to align all edges.

#6x30mm

TrimScrew

(032)End

Plinth

Assembly

Step 6: Attach Plinths to Corner Post Assembly

Part 3

C:Placeone(032)EndPlinthAssemblyontoeachCornerPostAssembly.Linethemupwithpreviouslyplaced

Plinths.Makesuretheyareushandtighttoeachotherandthenfastenwithtwo#6x30mmTrimScrewper

end.(Fig.6.5and6.6)

Fig. 6.5

Fig. 6.6

16 x #6 x 30 mm Trim Screw8 x (032) End Plinth Assembly 34.9 x 152.4 x 141.3 mm

Page is loading ...

Yardistry Preston Pergola User manual

Brand: Yardistry

Model: Preston Pergola

Type: User manual

This manual is also suitable for

12 x 12 Preston Arched Roof Pergola

Download PDF

report

Yardistry Preston Pergola User manual

This manual is also suitable for

Yardistry Preston Pergola User manual

Related papers

Other documents