Yardistry YM11542 Installation guide

Brand: Yardistry

Model: YM11542

Type: Installation guide

 1 support@yardistrystructures.com

Shaded sitting nook

Installation and Operating Instructions – YM11542

Yardistry – North America

Toll Free Customer Support: 1.888.509.4382

info@yardistrystructures.com

www.yardistrystructures.com

Yardistry / Selwood Products – Europe

Customer Support: +44 1284 852569

parts@selwoodproducts.com

www.selwoodproducts.com

Revised 02/13/2013

 2 support@yardistrystructures.com

Important Safety Notice!

Yardistrycomponentsareintendedforprivacy,decorativeandornamentaluseonly.

Product is NOT INTENDED for the following:

 •Asafetybarriertopreventunsupervisedaccesstopools,hottubs,spasorponds.

 •Asloadbearingsupportforabuilding,structure,heavyobjectsorswings.

 •Usedinstructuresthattrapwind,rainorsnowthatwouldcreateextraloadonthe

product.

Permanent structures may require a building permit. Asthepurchaserandorinstaller

ofthisproductyouareadvisedtoconsultlocalplanning,zoningandbuildinginspection

departmentsforguidanceonapplicablebuildingcodesand/orzoningrequirements.

Wood in NOT ame retardant and will burn.Grills,repitsandchimineasareare

hazardifplacedtooclosetoaYardistrystructure.Consultuser’smanualofthegrill,re

pitorchimneaforsafedistancesfromcombustiblematerials.

Wear gloves to avoid injuryfrompossiblesharpedgesofindividualelementsbefore

assembly.

During installation, follow all safety warnings provided with your tools and use

OHSA approved safety glasses.Somestructuresmayrequiretwoormorepeopleto

installsafely.

Check for underground utilities before digging or driving stakes into the ground!

General Information:WoodcomponentsaremanufacturedwithCedar(C.Lanceolata)

whichisprotectedwithfactoryappliedwater-basedstain.Knots,smallchecks(cracks)

andweatheringarenaturallyoccurringanddonotaffectthestrengthoftheproduct.

Annualapplicationofawater-basedwaterrepellentsealantorstainwillhelpreduce

weatheringandchecks.

www.yardistrystructures.com

Questions?

Calltollfreeorwriteusat:

1(888)509-4382

[email protected]

PatentsPending

General Information

 3 support@yardistrystructures.com

Limited Warranty

Yardistry warrants that this product is free from defect in materials and workmanship

for a period of one year from the original date of purchase. In addition, all lumber is

warranted for 5 years against rot and decay. This warranty applies to the original owner

and registrant and is non-transferable.

Regular maintenance is required to assure the integrity of your product and is a requirement of

the warranty. This warranty does not cover any inspection cost.

This Limited Warranty does not cover:

• Labor for replacement of any defective item(s);

• Incidental or consequential damages;

• Cosmetic defects which do not affect performance or integrity;

• Vandalism; improper use or installation; acts of nature;

• Actsofnatureincludingbutnotlimitedtowind,storms,hail,oods,excessivewater 

 exposure;

• Minor twisting, warping, checking, or any other natural occurring properties of wood that

do not affect performance or integrity.

Yardistryproductshavebeendesignedforsafetyandquality.Anymodicationsmadetothe

original product could damage the structural integrity of the product leading to failure and

possibleinjury.Yardistrycannotassumeanyresponsibilityformodiedproducts.Furthermore,

modicationvoidsanyandallwarranties.

This product is warranted for RESIDENTIAL USE ONLY. Yardistry disclaims all other

representations and warranties of any kind, express or implied.

This Warranty gives you specic legal rights. You may have other rights as well which vary from state to state or province to

province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of

consequential damages, and therefore this limitation may not apply to you.

Instructions for Proper Maintenance

YourYardistrystructureisdesignedandconstructedofqualitymaterials.Aswithalloutdoorproductsitwill

weatherandwear.Tomaximizetheenjoyment,safetyandlifeofyourstructureitisimportantthatyou,theowner,

properlymaintainit.

If you dispose of your Yardistry structure: Pleasedisassembleanddisposeofyourunitsothatitdoesnotcre-

ateanyunreasonablehazardsatthetimeitisdiscarded.Besuretofollowyourlocalwasteordinances.

HARDWARE:

• Checkmetalpartsforrust.Iffound,sandandrepaintusinganon-leadpaintcomplyingwith16CFR1303.

• Inspectandtightenallhardwareaftercompletionofassembly;afterrstmonthofuse;andthenannually.

Donotover-tightenastocausecrushingandsplinteringofwood.

• Checkforsharpedgesorprotrudingscrewthreads,addwashersifrequired.

WOODPARTS:

• Unprotectedtheywillappearweatheredovertime.Periodicapplicationofanexteriorwaterrepelllentor

stain(water-based)willhelpimproveappearanceandlife.

• Checkallwoodmembersfordeterioration,structuraldamageandsplintering.Sanddownsplintersand

replacedeterioratedwoodmembers.Aswithallwood,somecheckingandsmallcracksingrainisnormal

 4 support@yardistrystructures.com

4pc. (220) -

Beam End Short 25.4 x 101.6 x 203.2mm

5pc. (224) -

Trellis 25.4 x 63.5 x 914.4mm

1pc. (225) -

Panel Top Rail 38.1 x 76.2 x 1409.7mm

10pc. (212) -

Seat Top 15.9 x 85.7 x 1409.7mm

4pc. (213) -

Support 38.1 x 76.2 x 492.1mm

1pc. (211) -

Seat Back 38.1 x 76.2 x 1524mm

4pc. (226) -

Seat Back Brace 38.1 x 82.6 x 476.3mm

4pc. (221) -

X Horizontal A 38.1 x 63.5 x 419.1mm

2pc. (222) -

Arch Scroll 38.1 x 130.7 x 634.3mm

4pc. (223) -

X Diagonal 38.1 x 38.1 x 588.2mm

2pc. (218) -

Beam 25.4 x 101.6 x 492.1mm

1pc. (210) -

Seat Front 38.1 x 76.2 x 1524mm

2pc. (214) -

Short Support 38.1 x 114.3 x 381mm

4pc. (228) -

Insert - Sitting Nook Post 38.1 x 38.1 x 127mm

2pc. (215) -

Short Wide Support 38.1 x 184.2 x 406.4mm

Part Identification ( )

Dimensions are approximate and are shown to assist in the identification of parts for

assembly. Actual dimensions may be smaller or larger.

 5 support@yardistrystructures.com

1pc. (012) -

SittingNookSunshadeSetY70821-012

8pc.

YFW2

-5/16"FlatWasher

(Y05420-301)

2pc.

YP1

-XInsertPin

(Y20014-000)

8pc. YWC1

-WaferConnectorNut

(Y08420-205)

4pc.

YB1

-WaferBolt

1/4x2"-(Y07420-220)

4pc.

YB4

-WaferBolt

1/4x33/4"

-(Y07420-233)

14pc.

YS24

-WoodScrew

#10x4"-(Y06420-940)

1pc.

-#2RoberstonDriver(9200014)

54pc.

YS4

-WoodScrew

#8x3"-(Y06420-530)

26pc.

YS3

WoodScrew

#8x21/2"

-(Y06420-522)

80pc.

YS2

WoodScrew

#8x11/2"-(Y06420-512)

1pc.

SunburstBrackets -(Y70820-007)(2pk)

1pc.

CornerBraces -(Y70820-006)(2pk)

12pc.

YS5

Pan Screw

#8x1/2"

(Y06420-502)

Dimensions are approximate and are shown to assist in the identification of parts for

assembly. Actual dimensions may be smaller or larger.

Part Identification ( )

Part Identification (Actual Size)

2pc. (227) -

XPanelPostBack44.5x57.2x1930.4mm

2pc. (217) -

XPanelPostFront44.5x57.2x1930.4mm

1pc. (216) -

WindowTriplePanel38.1x495.3x1409.7mm

2pc. (219) -

EngineeredArchBeam25.4x186.3x1930.4mm

 6 support@yardistrystructures.com

PRODUCTNUMBER:YM11542

CARTONI.D.STAMP:_____________(Box1)

CARTONI.D.STAMP:_____________(Box2)

CARTONI.D.STAMP:_____________(Box3)

STOP STOPSTOP STOP

1-888-509-4382

support@yardistrystructures.com

C. Readtheassemblymanualcompletely,payingspecialattentiontoANSIwarnings;

notes;andsafety/maintenanceinformationonpages1-4.

 

•Followtheinstructionsinorder.



•Thisstructureisdesignedtobeassembledandinstalledideallybytwopeople,

DONOTattempttoinstallalone.

 •Considertheslopeofelevationwhereyouplantoinstallthestructure.Also,checkfor

gas,telephone,otherutilitiesorsprinklerlinelocationspriortoexcavatinganyholes.

D. 

Beforeyoudiscardyourcartonsllouttheformbelow.



•ThecartonI.D.stampislocatedontheendofeachcarton.

 •Pleaseretainthisinformationforfuturereference.Youwillneedthisinformationifyou

contacttheConsumerRelationsDepartment.

•Eachstepindicateswhichboltsand/orscrewsyouwillneedforassembly,aswellas

anyatwashers,lockwashers,t-nutsorlocknuts.

A.

Thisisthetimeforyoutoinventoryallyourhardware,woodandaccessories,

referencingthepartsidenticationsheets.Thiswillassistyouwithyourassembly.

Inventory Parts - Read This Before Starting Assembly

B. Ifthereareanymissingordamagedpiecesoryouneedassistancewith

assemblypleasecontacttheconsumerrelationsdepartmentdirectly.Callus

beforegoingbacktothestore.

 7 support@yardistrystructures.com

Step 1: Attach Short Supports

HardwareWood Parts

A:Layone(217)XPanelPostFrontandone(227)XPanelPostBackonedge,sothegroovedsidesfaceeach

other(g1.1).Noticetheholelocationonbothposts.

B:Attachone(214)ShortSupportcenteredonandushtothebottomofeach(217)XPanelPostFrontandone

(215)ShortWideSupportushtothebottomofandcenteredoneach(227)XPanelPostBackusing1(YS3)#8

x21/2”WoodScrewinthetopholeand1(YS4)#8x3”WoodScrewinthemiddleholesand1(YS24)#10x4”

WoodScrewinthebottomholesperboard(g.1.2&1.3).

C: Repeat A and B

4 x #8 x 2 1/2” Wood Screw

2 x Short Support 38.1 x 114.3 x 381 mm

2 x Short Wide Support 38.1 x 184.2 x 406.4

2 x X Panel Post Front 44.5 x 57.2 x 1930.4 mm

2 x X Panel Post Back 44.5 x 57.2 x 1930.4 mm

214

YS3

Fig. 1.1

215

Fig. 1.3

Fig. 1.2

Bottom View

227

214

217

YS4

227

217

Notice hole

locations toward

top of boards

227 217

214

215

YS3

215

217

227

YS24

YS4

4 x #8 x 3” Wood Screw

YS24

4 x #10 x 4” Wood Screw

 8 support@yardistrystructures.com

Step 2: Attach Inserts

Part 1

Hardware

Wood Parts

A:Looselyattachone(228)Insertinsidethegroovesofeach(217)XPanelPostFrontand(227)XPanelPost

Backwith1(YB4)1/4x33/4”WaferBolt(with5/16”atwasher)asshowningures2.1&2.2.Notetheangled

edgeof(228)Insertistowardsthebottom(g.2.2)

4 x 1/4 x 3 3/4” Wafer Bolt (5/16” at washer )4 x Insert 38.1 x 38.1 x 127mm

228

Fig. 2.1

Fig. 2.2

227

217

228

YB4

5/16”at

washer

Notice

orientation

 9 support@yardistrystructures.com

Step 2: Attach Inserts

Part 2

HardwareWood Parts

B:Withanadulthelperstanduppostsandplaceone(211)SeatBackontheoutsideofboth(227)XPanelPost

Backandtighttothetopof(215)ShortWideSupports(g2.3&2.4).Noticetheholeistowardthebottomofthe

board.Insertone1/4”ConnectorNutinto(211)SeatBackandlooselyattachtopreviouslyinstalled(YB4)1/4x3

3/4”WaferBoltoneachside(g2.4).



C:Placeone(210)SeatFrontontheoutsideofboth(217)XPanelPostFrontandtighttothetopof(214)Short

Supports(g2.3&2.4).Noticetheholeandanglededgeistowardsthetopoftheboardandthebevelededge

facesout(g2.4).Insertone1/4”ConnectorNutinto(210)SeatFrontandlooselyattachtopreviouslyinstalled

(YB4)1/4x33/4”WaferBoltoneachside(g2.3).

1 x Seat Front 38.1 x 76.2 x 1524 mm

1 x Seat Back 38.1 x 76.2 x 1524 mm

Fig. 2.3

210

4 x 1/4” connector nut

Fig. 2.4

210

215

211

227

217

214

YB4

(previously

installed)

1/4”ConnectorNut

211

Notice bevelled

edge face out

Tight

227

217

Noticehole

location



Notice angled

edge towards top

 10 support@yardistrystructures.com

Step 3: Insert X Panels

Part 1

HardwareWood Parts

A:Withanadulthelperslideone(221)XHorizontalAdownthegroovesofeach(217)XPanelPost

Frontand(227)XPanelPostBacksoitsitstighttothetopof(228)Insertsusing2(YS4)#8x3”Wood

Screwsperside(g3.1&3.2).

8 x #8 x 3” Wood Screw

2 x X Horizontal A 38.1 x 63.5 x 419.1 mm

221

217

227

YS4

Fig. 3.1

Fig. 3.2

221

228

x2perside

YS4

Tight

 11 support@yardistrystructures.com

Step 3: Insert X Panels

Part 2

HardwareWood Parts

B:PlaceoneXInsertPinintoone(223)XDiagonal,thenattachasecond(223)XDiagonaltoformacompleteX

Panel.Makesurethepiecesaretighttoeachother(g3.3&3.4)

Repeat for second assembly.

4 x X Diagonal 38.1 x 38.1 x 588.2 mm

Fig. 3.3

2 x X Insert Pin

XInsert

Pin

223

Fig. 3.4

Side View

223

 12 support@yardistrystructures.com

Step 3: Insert X Panels

Part 3

HardwareWood Parts

C:SlideonecompletedXPaneldown

thegroovesofeach(217)XPanelPost

Frontand(227)XPanelPostBacksoit

sitstighttothetopof(221)XHorizontal

InsertAasshowning.3.5.

D:Slideone(221)XHorizontalAdown

tosittighttothetopofeachcompleted

XPanel(g.3.5&3.6)andattachwith2

(YS4)#8x3”WoodScrewsperside(g.

3.6)

8 x #8 x 3” Wood Screw

2 x X Horizontal A 38.1 x 63.5 x 419.1 mm

2 x Completed X Panel

221

227

YS4

Fig. 3.5

221

Fig. 3.6

x2perside

217

YS4

Tight

CompletedX

Panel

 13 support@yardistrystructures.com

Step 4: Attach Arch Scrolls

HardwareWood Parts

Note orientation of Arch Scrolls (g. 4.1, 4.2 & 4.3).

A:Insertone(222)ArchScrollbetween(217)XPanel

PostFrontand(227)XPanelPostBacksoatedgeis

tighttothetopof(221)XHorizontalA(g.4.2&4.3)

with2(S4)#8x3”WoodScrewsasshowning4.3.

Repeat on other side of assembly.

4 x #8 x 3” Wood Screw

2 x Arch Scroll 38.1 x 130.7 x 634.3 mm

222

Fig. 4.3

x2

Tight

YS4

227

Fig. 4.1

Front

Fig. 4.2

217

Note: Flat edge

sits tight to (221)

X Horizontal A



221

YS4

 14 support@yardistrystructures.com

Step 5: Attach Beams to X Panel Posts

HardwareWood Parts

8 x #8 x 2 1/2” Wood Screw

2 x Beam 25.4 x 101.6 x 492.1 mm

218

227

YS3

Fig. 5.1

221

Fig. 3.6

217

YS4

Flush

A:Flushtothetopandoutsideedgesof(217)XPanelPostFrontand(227)XPanelPostBackattachone

(218)Beampersidewith4(YS3)#8x21/2”WoodScrewsperboard(g.5.1&5.2).

Fig. 5.2

218

227

217

Flush

YS3

x4perboard

 15 support@yardistrystructures.com

Step 6: Attach Supports

HardwareWood Parts

16 x #8 x 3” Wood Screw

4 x Support 38.1 x 76.2 x 492.1 mm

213

YS4

Fig. 6.1

A:Attachone(213)Supporttighttotheinsideof(217)XPanelPostFrontand(227)XPanelPostBackon

eachsideandushtothetopsof(211)SeatBackand(210)SeatFrontusing4(YS4)#8x3”WoodScrews

perboard(g6.1&6.2).Ensurethewideendof(213)Supportisagainst(211)SeatBack(g.6.2).

Fig. 6.2

B:Centreremaining(213)Supports

overpilotholesin(211)SeatBack

and(210)SeatFrontasshowning.

6.1andattachusing4(YS4)#8x3

WoodScrewsperboard.

217

227

213

210

YS4

211

x4perboard

Tight

Flush

Front View

Tight

Flush

 16 support@yardistrystructures.com

Step 7: Attach Seat Back Braces

Part 1

HardwareWood Parts

6 x #8 x 3” Wood Screw

2 x Seat Back Brace 38.1 x 82.6 x 476.3 mm

226

YS4

Fig. 7.1

Flush

A:Placetwo(226)SeatBackBraceson(213)Supportsothatthestraightedgesareushtothebackof

each(227)XPanelPostBackandthebottomistightto(211)SeatBackasshowning.7.1&7.2.Notethe

orientationof(226)SeatBackBrace(g7.2).

B: Attacheach(226)SeatBackBracetoeach(227)XPanelPostBackusing3(YS4)#8x3”Wood

Screwsperboard(g.7.1&7.2).

Fig. 7.2

227

YS4

211

Tight

Front View

213

 17 support@yardistrystructures.com

Step 7: Attach Seat Back Braces

Part 2

HardwareWood Parts

6 x #8 x 1/2” Pan Screw

2 x Corner Brace

2 x Seat Back Brace 38.1 x 82.6 x 476.3 mm

226

YS5

Fig. 7.3

C:Placeone(226)SeatBackBraceonremaining(213)Supportsasshowning7.3&7.4.Attach(226)

SeatBackBraceto(211)SeatBackusing1CornerBracewith3(YS5)#8x1/2”PanScrewsperboard(g.

7.3&7.4).

Fig. 7.4

YS5

Tight

Back View

226

213

211

Corner

Bracket

x3per

bracket

226

213

 18 support@yardistrystructures.com

Step 8: Attach Seat Tops

Part 1

HardwareWood Parts

16 x #8 x 1 1/2” Wood Screw

2 x Seat Top 15.9 x 85.7 x 1409.7mm

212

YS2

Fig. 8.1

A:Flushtothefrontedgeof(210)SeatFrontandoutsideedgeof(213)Supportsattachone(212)SeatTop

with8(YS2)#8x11/2”WoodScrewsperboard(g.8.2).

B: Attachone(212)SeatToptighttothefrontof(226)SeatBackBracesandoutsideedgesof(213)Supports

using8(YS2)#8x11/2”WoodScrewsperboard(g8.1&8.2).

Fig. 8.2

217

Flush

210

213

x8perboard

212

Flush

Tight

226

212

217

YS2

 19 support@yardistrystructures.com

Step 8: Attach Seat Tops

Part 2

HardwareWood Parts

24 x #8 x 1 1/2” Wood Screw

3 x Seat Top 15.9 x 85.7 x 1409.7

212

YS2

Fig. 8.3

C: Evenlyspacethree(212)SeatTopsbetweenpreviouslyinstalled(212)SeatTopsto(213)Supportsand

attachusing8(S2)#8x11/2”WoodScrewsperboard(g.8.3).

212

YS2

x8per

board

213

(hidden)

213

 20 support@yardistrystructures.com

Step 8: Attach Seat Tops

Part 3

HardwareWood Parts

40 x #8 x 1 1/2” Wood Screw

5 x Seat Top 15.9 x 85.7 x 1409.7 mm

212

YS2

213

Flush

D: Attachone(212)SeatTopushtothetopfaceof(212)SeatTopandone(212)SeatTopushtothetop

ofallfour(226)SeatBackBracesusing8(YS2)#8x11/2”WoodScrewsperboard(g8.4).

E: Evenlyspacethree(212)SeatTopsbetweenpreviouslyinstalled(212)SeatTopsthenattachto(226)

SeatBackBracesusing8(YS2)#8x11/2”WoodScrewsperboard(g.8.4).

Fig. 7.2

212

Fig. 7.1

Flush

226

Tight

212

x8per

board

226

YS2

212

Page is loading ...

Yardistry YM11542 Installation guide

Brand: Yardistry

Model: YM11542

Type: Installation guide

Download PDF

report

Yardistry YM11542 Installation guide

Yardistry YM11542 Installation guide

Related papers

Other documents