2. LIVING BASICS
  3. Single Handle

LIVING BASICS Single Handle User manual

  • Hello! I've reviewed the user manual for the LIVING basics Bath Faucet. This document provides detailed assembly instructions, diagrams, and parts lists. It covers the installation of the faucet, including the valve body, shower arm, and hand shower. I'm here to assist you with any questions you might have about your new bath faucet installation process.
  • What type of valve is used?
    Is there a water flow regulation function?
    What materials are required for installation?
Pipe tape
Philips Screwdriver Adjustable wrench Eye protection Flashlight
Solid Brass Construction
Pressure Balance Valve/Gear Type
Easy Installation
Single Handle Pressure Balance
Bath Faucets
Ø40 Pressure
Balance Valve
DIAGRAM AND PARTS LIST
RECOMMENDED TOOLS
Allen key
1
-1- -2-
[2]
[1]
5
ASSEMBLY INSTRUCTIONS
RECOMMENDED MOUNTING DIMENSIONS
RECOMMENDED
12.5mm[1/2"]
1/2-NPT14
Min Finished Wall
Max Finished Wall
55mm[2 3/16"]
78mm[3 1/16"]
Electric drill
4.setscrew
1. Installation reference size ,main body fixed size( width 40mm ) . Knock 2pcs
setscrews(4) into holes .
2. Connect the pipes into the valve body(5) ; Put valve body(5) in the hole and
fix it by the screw(7) . then connect the water supply hoses .
7.screw
MAIN BODY FIXED SIZE
40mm
1
2
3
5
67
8
9
10
11
12
13
14
15
16 17 19
18
41.Shower arm
2.Gasket
3.Shower head
4.Setscrew
5.Valve body
6.Cover plate
7.Tapping screw
8.Panel
9.Handle
10.Screw
11.Red/ blue button
12.Allen key
13.Diverter
14.Screw
15.Button
16.Elbow
17.Hand shower
18.Gasket
19.Flexible hose
[4]
[3]
[6]
[5]
-4-
3.Plug the water outlets after the valve body is installed.
4.Remove the black cover plate(6). Install the handle(9) and diverter(13).Provide water
from water inlet.
5.Remove handle(9) and diverter(13), put on cover plate(6) after water test is ok.
6.Backfill the wall in concrete, tile on concrete and then remove the black cover
plate(6)when available.
Proceed to next step if no leaking after the testing.
[8]
[7]
-3-
6
9
13
9
13
6
6
And then test the water pipes leaking or not as below:
1)Test 3 min @ 1.6 Mpa when the ceramic cartridge is closed.
2)Test 3 min @ 0.4 Mpa when the ceramic cartridge is open.
The valve body is with water flow
regulation function. If there is great
deviation in cold and hot water flow,
it could be adjusted at the point
indicated by the arrow .
(Turn down in clockwise rotation)
The tile surface should be 10cm lower
than the black cover plate(6).
8
9
10
11
12
13
14
15
7.Feed the valve body with panel(8), handle(9) and diverter(13), then use the allen key(12)
and screw(10)/(14) to secure handle(9) and diverter(13), put on the red/ blue button(11)/(15).
8.Take off hand shower, up and down plugs, turn on the cartridge to wash out the dirt in the
water tube.
[10]
1
2
3
17
16
18
19
[9]
9.Use the tape to install in turn, shower arm (1), elbow(16). Then install the shower head(3)
with the gasket(2).
10. Connect the flexible hose(19), gasket(18) and hand shower (17). Testing for leakage
after installation. Complete installation.
/