Ops-Core EPP Pad Replacement Kit Operating instructions

Ops-Core
Brand
Ops-Core
Model
EPP Pad Replacement Kit
Type
Operating instructions

Ops-Core EPP Pad Replacement Kit allows you to customize the fit of your Ops-Core FAST Helmet for optimal comfort and protection. This kit includes 2x 1/2” Top Pads, 2x 3/4” Top Pads, 2x Side Pads, 1x 1/2" Rear Pad, and 1x 3/4” Rear Pad. The kit is compatible with all FAST Helmets in sizes S/M, M/L, L/XL, and XXL.

The kit's components are designed to provide various levels of cushioning and support, allowing you to fine-tune the helmet's fit to your head shape and size. The top pads come in two thicknesses (1/2” and 3/4”) to adjust the helmet's height on your head, ensuring it sits securely without causing discomfort or pressure on your forehead.

Ops-Core EPP Pad Replacement Kit allows you to customize the fit of your Ops-Core FAST Helmet for optimal comfort and protection. This kit includes 2x 1/2” Top Pads, 2x 3/4” Top Pads, 2x Side Pads, 1x 1/2" Rear Pad, and 1x 3/4” Rear Pad. The kit is compatible with all FAST Helmets in sizes S/M, M/L, L/XL, and XXL.

The kit's components are designed to provide various levels of cushioning and support, allowing you to fine-tune the helmet's fit to your head shape and size. The top pads come in two thicknesses (1/2” and 3/4”) to adjust the helmet's height on your head, ensuring it sits securely without causing discomfort or pressure on your forehead.

MADE IN USA
REPLACEMENT EPP PAD KIT
INSTALLATION INSTRUCTIONS
© OPS-CORE 2015 06-07-200 REV. B
FOR ALL FAST HELMETS
S/M & M/L
60-98-203
L/XL & XXL
60-98-303
HELMET SIZE
COMPONENTS
INSTALLATION & FIT
REPLACEMENT EPP PAD KIT INCLUDES:
(2) ½” TOP PADS, (2) ¾” TOP PADS, (2) SIDE PADS, (1) ½“ REAR PAD, (1) ¾” REAR PAD
NOTE: REPLACEMENT FRONT EPP PAD IS SOLD SEPARATELY.
PAD PLACEMENT
REPLACEMENT EPP PAD LOCATION:
Remove and throw away the old EPP Pads. Position and attach the pads to the Velcro
®
patches inside the
helmet as shown. The Top and Rear Pads come in two different thicknesses. Follow the “Installation and Fit”
instructions to determine the correct pad thickness for your custom fit.
Side Pad Side Pad
Top Pad
Top PadRear Pad
HEIGHT ADJUSTMENT
• The distance from the top of the eyebrow to the bottom
of the fitband should be approximately 0.5”- 1”. There
should also be enough room around your ears for
COMMs / hearing protection.
• If the helmet sits too low on your head, remove the ½”
top pads and install the ¾” top pads.
• If the helmet sits at an uncomfortable angle, adjust the
top pads, or use a combination of ½” and ¾” top pads
until it sits correctly.
ADJUST THE TOP PADS
• Put the helmet on. ½” pads come pre-installed
in the helmet. Turn the dial to loosen the fitband
so that all of the helmet weight is resting on top
of your head.
• With the fitband loose, check how high / low the
helmet is sitting. Forehead pad should be above and not
resting on the bony ridge of your eyebrows.
ADJUST THE REAR PADS
• Install the ¾” rear pad. Put the helmet on.
• If you feel uncomfortable pressure on your forehead, take the
¾” pad out and put in the ½”pad.
• If it feels the same as with the ½” pad (can’t notice the
difference) then keep the ¾” installed. This will make the
helmet more stable and comfortable.
3
/
4
”
1
/
2
”
Side Pad Top Pad Rear Pad
3
/
4
”
1
/
2
”
INSTALL THE SIDE PADS
• Install the side pads onto the Velcro patches
on the inside of the helmet. These pads
make the helmet more stable and increase
protection from side impacts.
• If they feel tight or uncomfortable, try to
relocate them into a position that feels good.
0.5”-1”
Top Pad
  • Page 1 1
  • Page 2 2

Ops-Core EPP Pad Replacement Kit Operating instructions

Ops-Core
Brand
Ops-Core
Model
EPP Pad Replacement Kit
Type
Operating instructions

Ops-Core EPP Pad Replacement Kit allows you to customize the fit of your Ops-Core FAST Helmet for optimal comfort and protection. This kit includes 2x 1/2” Top Pads, 2x 3/4” Top Pads, 2x Side Pads, 1x 1/2" Rear Pad, and 1x 3/4” Rear Pad. The kit is compatible with all FAST Helmets in sizes S/M, M/L, L/XL, and XXL.

The kit's components are designed to provide various levels of cushioning and support, allowing you to fine-tune the helmet's fit to your head shape and size. The top pads come in two thicknesses (1/2” and 3/4”) to adjust the helmet's height on your head, ensuring it sits securely without causing discomfort or pressure on your forehead.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents