Marantec Comfort 260 Owner's manual

Brand: Marantec

Model: Comfort 260

Category: Garage Door Opener

Type: Owner's manual

This manual is also suitable for

Comfort 260 accu

Operating instructions

Last updated: 04.2014

Operator systems for garage doors

Comfort 260 accu

2 Operating instructions, Comfort 260 accu (#114332 – GB)

Table of Contents

1. General safety instructions .....................3

1.1 Intended use ................................3

1.2 Target group ................................3

1.3 Warranty ...................................3

2. Scope of supply ..............................4

3. Door system .................................5

4. Installation ..................................6

4.1 Preparing for installation .......................6

4.2 Installing the drive ............................6

4.3 Installing the rechargeable battery unit ...........10

4.4 Charge controller function ....................10

4.5 Connection of control elements .................11

4.6 Completing the installation ....................12

4.7 Rechargeable battery unit .....................12

5. Setting in operation ..........................14

5.1 Overview of the controls ......................14

5.2 Status display ..............................15

5.3 Factory settings .............................15

5.4 Express programming ........................15

5.5 Function test ...............................16

5.6 Special programming .........................17

6. Operation ..................................22

6.1 Hand transmitter ............................22

6.2 Release mechanism ..........................24

7. Maintenance ...............................24

8. Disassembly ................................24

9. Disposal ...................................25

10. Rectifying faults .............................25

11. Appendix ..................................27

11.1 Technical Data ..............................27

11.2 Declaration of Incorporation ....................28

Regarding this document

– Original instruction manual.

– Part of the product.

– Read these instructions carefully before use and keep them in a

safe place for future reference.

– Protected by copyright.

– No part of this manual may be reproduced without our prior

approval.

– Subject to alterations in the interest of technical progress.

– All dimensions are given in millimetres.

– The drawings are not true to scale.

Meaning of symbols

DANGER!

Safety notice indicating a danger that will directly result in death or

severe injury.

WARNING!

Safety notice indicating a danger that could result in death or severe

injury.

CAUTION!

Safety notice indicating a danger that could result in slight or

moderate injuries.

NOTICE

Safety notice indicating a danger that could result in damage to

property or in irreparable damage to the product.

CHECK

Reference to a check that needs to be carried out.

REFERENCE

Reference to separate documents that must be observed.

• Instruction requiring action

– List, itemisation

➔ Reference to other sections of this document

) Factory settings

DANGER!

IMPORTANT SAFETY INSTRUCTIONS:

ATTENTION! IT IS VITALLY IMPORTANT FOR THE SAFETY OF

PERSONS THAT YOU FOLLOW ALL THE INSTRUCTIONS.

KEEP THESE INSTRUCTIONS IN A SAFE PLACE.

IMPORTANT INSTRUCTIONS FOR SAFE INSTALLATION:

ATTENTION! SERIOUS INJURIES CAN BE CAUSED IF THE EQUIP-

MENT IS NOT INSTALLED CORRECTLY – BE SURE TO FOLLOW ALL

THE INSTALLATION INSTRUCTIONS.

Operating instructions, Comfort 260 accu (#114332 – GB) 3

1. General safety instructions

DANGER!

Failure to comply with the documentation could result in

life-threatening danger!

• Be sure to follow all the safety instructions in this document.

1.1 Intended use

– The operator system is to be used only for opening and closing

doors.

– Never use the door system to help lift persons or objects.

The following applies for the product Comfort 260 accu:

– Only approved for use in dry rooms.

– The following values must be observed:

– maximum tensile force

– maximum compressive force

– maximum door size

– maximum door weight

➔ “11.1 Technical Data”

– The product is intended for private use.

– The product is suitable only for counterbalanced sectional and up-

and-over doors with a fall arrest system.

1.2 Target group

– Installation, connection and setting in operation:

qualied,trainedspecialistpersonnel.

– Operation, inspection and servicing:

the operator of the door system.

Requirementstobemetbyqualiedandtrainedspecialiststaff:

– Knowledgeofthegeneralandspecicsafetyandaccident-

prevention regulations.

– they have knowledge of the relevant electrical regulation,

– Training in the use and care of appropriate safety equipment.

– Adequateinstructionandsupervisionbyqualiedelectricians.

– The ability to recognise hazards that can be caused by electricity.

– Knowledge of the application of the following standards

– EN 12635 (“Doors and gates - Installation and use”),

– EN 12453 (“Safety in use of power operated doors -

Requirements”),

– EN 12445 (“Safety in use of power operated doors -

Test methods”),

Requirements to be met by the operator of the door system:

– Knowledge and safekeeping of the instruction manual.

– Knowledge of general safety and accident-prevention regulations.

1.3 Warranty

The product is manufactured in accordance with the guidelines

and standards listed in the manufacturer’s declaration and in the

declaration of conformity. The product left the factory in perfect order

with regard to safety.

In the following cases, the manufacturer will accept no liability for

damage. The warranty on the product and accessory components

becomes void in the event of:

– Failure to observe these operating instructions.

– Incorrect handling and use of the product for anything other than

its intended purpose.

– Workbeingcarriedoutbyunqualiedpersonnel.

– Changesormodicationstotheproduct.

– The use of replacement parts that have not been approved or were

not manufactured by the manufacturer.

The warranty does not cover batteries, rechargeable batteries, fuses or

bulbs.

Further safety instructions are given in the relevant sections

of the document.

➔ “4. Installation”

➔ “5. Setting in operation”

➔ “6. Operation”

➔ “7. Maintenance”

➔ “8. Disassembly”

4 Operating instructions, Comfort 260 accu (#114332 – GB)

2. Scope of supply

Various versions of the product are available. Please refer to the table

and check the items included in the delivery to determine which ver-

sion you have received.

Theremaybesomecountry-specicdifferences.

Item Door operator

Item Fittings A B

2x 2x

1x 1x

2x 2x

1x 1x

2x 2x

1x –

– 1x

Item Fastening elements - 01 A B

4x 4x

2x 2x

1x 1x

2x 2x

1x 1x

1x –

– 4x

Item Fastening elements - 02

Item Warning signs

Operating instructions, Comfort 260 accu (#114332 – GB) 5

Item Hand transmitter Multi-Bit bi·linked

1x 1x

1x –

– 1x

1x 1x

1x –

– 1x

Item Rechargeable battery unit

3. Door system

Overview

3 / 1

This is just an example of a door system. The details can vary according

to the type of door and the associated equipment. The system shown

comprises the following components:

1 Photocell

2 Key switch

3 Free-standing post (for code keypad, transponder etc.)

4 Solar module (optional)

5 Rechargeable battery unit

REFERENCE

For further information regarding accessory items, please see the

manufacturer’s website.

For the installation and cabling of the door sensors, control elements

and safety equipment, the relevant installation instructions must be

observed.

6 Operating instructions, Comfort 260 accu (#114332 – GB)

4. Installation

DANGER!

Life-threatening danger due to electric shock!

• It is vital that you disconnect the operator system from the

power supply before commencing cabling work. Take measures

to ensure that the power supply remains disconnected for the

duration of the work.

• Observe the local safety regulations.

• It is imperative that you lay power cables separately from control

cables.

The control voltage is 24 V DC.

NOTICE

Material damage resulting from incorrect installation of the

operator!

To avoid installation errors and damage to the door or operator

system, the following installation instructions must be observed at all

costs.

• Ensure that the door is in good mechanical condition:

– The door remains stationary in every position.

– The door can be moved easily.

– The door opens and closes properly.

• Install all impulse transmitters and control equipment (such as

radio code buttons e. g.) within sight of the door and at a safe

distance from the door’s moving parts. The installation height

mustbeatleast1.5metresfromtheground.

• Onlyusexingmaterialsthataresuitableforthefoundation

material in question.

4.1 Preparing for installation

Before commencing installation, the following works must be carried

out without fail.

Supply package

• Check which version you have received and that all the parts are

present.

• Ensure that a suitable operator boom is available.

• Check that all the necessary accessory parts for your installation

situation are present.

Door system

• Remove any components (such as ropes, chains, brackets, etc.) from

the door that are no longer needed.

• All equipment that will no longer be required after the door

operator system has been installed must be taken out of service.

For garages without a second entrance:

• Fit the garage door with an emergency release mechanism so that

you can gain entry to the garage if there is a malfunction.

If a release set is used:

• Check that the door catches function properly. On no account

should the door catches be taken out of service.

If no release set is used:

• Remove the door catches or take them out of service.

REFERENCE

When using and installing accessory equipment, observe the

corresponding documentation.

4.2 Installing the drive

4.2 / 1

4.2 / 2

ø 5 – 5,5

Operating instructions, Comfort 260 accu (#114332 – GB) 7

NOTICE

Possibility of damaging the motor unit!

Do not use force, as this could damage the teeth of the gears!

• Carefullyxtheoperatorboomtothemotorunit.

4.2 / 3

4.2 / 4

ø 5 – 5,5

8 Operating instructions, Comfort 260 accu (#114332 – GB)

WARNING!

Possibility of serious injury due to falling components!

• Secure the operator system to prevent if from falling before it is

properlyxedinplace.

4.2 / 5

NOTICE

Possibility of damaging the door leaf!

At its highest point during opening, the top edge of the door leaf

must be 10 - 50 mm below the bottom edge of the horizontal

operator boom.

• Fix the lintel joining plate for the operator boom. It must be

positioned centrally above the door leaf.

4.2 / 6

10 - 50

ø 10

4.2 / 7

4.2 / 8

4.2 / 9

4.2 / 10

4.2 / 11

Operating instructions, Comfort 260 accu (#114332 – GB) 9

4.2 / 12

5-10

a = 90°

b = 9 Nm

5-10

4.2 / 13

4.2 / 14

2/3

1/3

4.2 / 15

ø 10

4.2 / 16

10 Operating instructions, Comfort 260 accu (#114332 – GB)

4.3 Installing the rechargeable battery unit

NOTICE

Risk of property damage due to improper installation of the

rechargeable battery unit!

Moisture and vibrations may result in the destruction of the entire

electronic system.

• Choose a dry installation position.

• During installation and operation of the battery unit, ensure that

the connector never points downwards.

• Secure the rechargeable battery unit to prevent it from falling.

4.3 / 1

ø 6

4.3 / 2

4.3 / 3

4.3 / 4

4.4 Charge controller function

4.4 / 1

Status LED A (green) LED B (red)

< 1/4

Operating instructions, Comfort 260 accu (#114332 – GB) 11

4.5.1 Overview of the control element connections

4.5.1 / 1

XB03 XB72

XB03 Connection for

– external control elements

– Photocell

➔ “Level 5, Menu 1 - Programmable impulse

input (terminal 1/2)”

➔ “4.5.3 Terminal block XB03”

XB72

Connection for modular antenna

➔ “4.5.2 Terminal block XB72”

4.5.2 Terminal block XB72

4.5.2 / 1

Key

< 1/4

LED on

< 1/4

LEDashing

< 1/4

LEDashingquickly

< 1/4

LED off

4.5 Connection of control elements

DANGER!

Life-threatening danger due to electric shock!

• It is vital that you disconnect the operator system from the

power supply before commencing cabling work. Take measures

to ensure that the power supply remains disconnected for the

duration of the work.

NOTICE

Danger of material damage resulting from incorrect

installation of the operator!

If an external voltage is connected to terminal block XB03, the entire

electronic system will be irreparably damaged.

• Connect only potential-free contacts to terminals 1, 2 and 4

(XB03).

12 Operating instructions, Comfort 260 accu (#114332 – GB)

4.5.3 Terminal block XB03

4.5.3 / 1

4.5.3 / 2

- XB03

7170

-W1

-W2

-W1

-W2

- AP27

-Sb1

-Sb4

M14E001

1 24 V DC + / 50 mA max.

2 Impulse

3 GROUND -

4 Hold circuit, active after a reset

70 GROUND

71 Photocell

AP27 Photocell

RX Photocell receiver

TX Photocell transmitter

Sb1 Impulse button

Sb4 Normally closed contact for hold circuit

4.5.3 / 3

4.6 Completing the installation

• Takethewarningsignsregardingtrappinghazardsandafxthem

permanently at noticeable locations.

• After installation is complete, ensure that no door parts extend

onto the public footpath or the street.

4.7 Rechargeable battery unit

4.7.1 General information about the operation of the

rechargeable battery unit

WARNING!

Risk of injury due to improper handling of the plug-in

charger and the rechargeable battery unit!

There is an explosion hazard due to the formation of explosive gases

during the charging of lead batteries.

Ifmoistureispresent,thereisareandshort-circuithazarddueto

electric shocks. In order to exclude hazards:

• Charge the battery unit exclusively in well-ventilated rooms.

• Never short-circuit the battery unit.

• Avoidreandopenlight.

• The plug-in charger must only be operated in dry rooms.

• Protect the unit against moisture.

• Protect the unit against oils and sharp edges.

• Check the unit regularly for damage.

NOTICE

Malfunction due to improper battery operation.

If the battery unit is operated at low battery voltage despite a warning

signal from the operator system, it will disconnect from the drive

system to prevent discharge to low level. To ensure that it functions

correctly, the rechargeable battery unit must be charged as follows:

– In the case of occasional use, every 2 months at the latest,

– In the case of non-use, every 6 months at the latest.

Duration of use

Under optimum conditions, a battery unit has a useful life of approx.

30dayswith4(openingandclosing)movementcyclesperday.

Voltage display

A battery unit switch-on test is conducted when the battery unit

is connected to the drive system. If the battery unit is not charged

sufciently,theoperatorlightingwillash5timesafterreachingthe

OPEN end position. The storage battery unit then needs to be charged

immediately.

➔ “4.4 Charge controller function”

Standby

It is possible to activate the operator from standby mode as follows:

– by pressing the +, – or P key,

– by pressing a button on the hand transmitter,

– by pressing an internal button that is connected to terminals 1

and2.

Operating instructions, Comfort 260 accu (#114332 – GB) 13

Displays

Green LED on:

The unit is in charging mode.

GreenLEDashing:

The charging process is complete.

4.7.2 / 4

4.7.2 / 5

4.7.2 / 6

Only if a solar module is used.

4.7.2 Charging procedure

NOTICE

Risk of material damage due to improper handling!

Only if solar module is connected:

To ensure that it functions correctly, it is essential that action is taken

in the following order only:

– The operator cable must only be removed if the solar module has

rstbeendisconnectedfromtherechargeablebatteryunit.

➔ “4.7.2 / 1”

– The solar module must only be connected to the rechargeable

battery unit if the operator cable has been connected to the

batteryunitrst.

➔ “4.7.2 / 6”

4.7.2 / 1

Only if a solar module is used.

4.7.2 / 2

4.7.2 / 3

14 Operating instructions, Comfort 260 accu (#114332 – GB)

5. Setting in operation

Before initial operation and at regular intervals of no more than one

year, power-operated windows, doors and gates must be inspected by a

qualiedperson(wherebywritteninspectionrecordsmustbekept).

After setting the system in operation, the operator of the door system,

or the operator’s representatives, must be instructed in the operation of

the system.

WARNING!

Danger of injury due to uncontrolled movement of the

door!

• Ensure that children can not play with the door controls or the

hand transmitter.

• Before setting the door in motion, make sure that no persons or

objects are within the danger zone of the door.

• Before going through the door opening, make sure that the door

is in the OPEN position.

• Check all the existing emergency command devices.

• Pay attention to potential crushing and shearing zones in the

door system.

• Never touch a running door, the guide rail or any moving parts.

• The regulations of DIN EN 13241-1 (“Doors and gates - Product

Standard”) must be observed.

5.1 Overview of the controls

Control elements

LED display

Drive the door in the OPEN direction,

increase the value

Drive the door in the CLOSE direction,

decrease the value

Startprogramming,conrmandsavevalues

Legend

Thedisplayashes

Display lights up

Display Function / Element

Ready for operation

Door position: CLOSED

Door position: OPEN

Fault message / Maintenance indicator in CLOSED

door position

Photocell or closing edge safety device

Remote control

External button

Status display

(Example showing display 3 – rechargeable

battery connected)

➔ “5.2 Status display”

Level indicator (example: Level 2)

Menu and parameter indicator

(example:Menu3,Parameter8)

Minute indicator

Times exceeding one minute are shown in

minutes and seconds.

Example: 1.2 = 1 minute + 20 seconds =

80seconds

Operating instructions, Comfort 260 accu (#114332 – GB) 15

5.2 Status display

Display Function / Element

Rechargeable battery connected

Warning time indicator (only for programmed

automatic closing)

5.3 Factory settings

Using the reset procedure, the operator parameters can be restored to

their original factory settings.

➔ “Level 1, Menu 8 – RESET”

5.4 Express programming

To set the operator system properly in service and after every reset, the

express programming procedure must be carried out.

Requirements:

– The door must be in the CLOSED position.

– The carriage must be coupled up.

➔ “6.2 Release mechanism”

When in programming mode, the controls will revert automatically to

operating mode if a period of 120 seconds passes without any buttons

being pressed.

A corresponding fault number will be displayed.

➔ “10. Rectifying faults”

• Carry out the express programming procedure.

CHECK

A function test must be carried out after express programming.

➔ “5.5 Function test”

Express programming

1. Programming the “OPEN” door position

The control system is in

operating mode.

P > 3 sec. < 10 sec.:

Start express programming.

Drive the door to the OPEN

position.

Save the OPEN position.

2. Programming the “CLOSED” door position

Drive the door to the CLOSED

position.

Save the CLOSED position.

3. Programming the remote control Multi-Bit

Press the hand transmitter

button.

Release the hand transmitter

button.

Save the remote control

setting.

End express programming.

The control system is in

operating mode.

16 Operating instructions, Comfort 260 accu (#114332 – GB)

Express programming

3. Programming the remote control bi·linked

Open the rear panel of the

hand transmitter.

Press the programming button

on the hand transmitter.

Press the hand transmitter

button.

Release the hand transmitter

button.

Save the remote control

setting.

End express programming.

The control system is in

operating mode.

Close the rear panel of the

hand transmitter.

5.5 Function test

5.5.1 Programming run for setting the driving power

Duringthersttworunsafterthedoorpositionshavebeenpro-

grammed, the operator system determines the maximum required

driving power.

• Drive the operator system (with the door coupled up) from the

CLOSED door position to the OPEN position and back again,

without interruption.

• Check the driving power.

Check the driving power

The control system is in

operating mode.

The door should open and

move to the saved “OPEN”

door position.

The door should close and

move to the saved “CLOSED”

door position.

The door operator should move

the door in the OPEN or CLOSE

direction.

The operator system should

stop.

The operator system should run

in the opposite direction.

Operating instructions, Comfort 260 accu (#114332 – GB) 17

5.5.2 Checking the automatic cut-out

WARNING!

Danger of injury due to incorrectly programmed values for

the door driving power!

• Check the automatic cut-out function in the OPEN and CLOSE

directions.

Automatic cut-out in the OPEN direction

This checking procedure only applies to operator systems that are

installed to operate doors that have openings in the door leaf (with

openings > 50 mm in diameter):

• During travel, apply a load of 20 kg to the door at the mid point of

the bottom edge of the door:

The door should stop immediately.

Automatic cut-out in the CLOSE direction

This checking procedure applies to all door systems.

• Placeanobject,50mminheight,ontheoor.

• Drive the door towards the obstacle:

The operator system should stop and reverse when it touches the

obstacle.

The settings of the OPEN and CLOSING operator forces remain saved

even if the power supply is interrupted.

The parameters are returned to the factory settings only after a reset.

➔ “Level 1, Menu 8 – RESET”

5.5.3 Checking the photocell

Photocell

• Check all the photocells individually by triggering them.

• Check all the photocells just before the door reaches the CLOSED

position.

Special points regarding door-frame photocells

– A door-frame photocell must function above the position at which

it is installed. Below the installation position, the function of the

photocell is suppressed by the control unit.

– If several photocells are connected, all the photocells function in

the same way as a door-frame photocell, if present.

5.6 Special programming

WARNING!

Danger of injury due to incorrect settings for the door

driving power!

Important factory settings can be changed when programming the

special functions.

• Check the programmed parameter values.

• Check the programmed door driving power values after changes

have been made to the automatic cut-out setting.

➔ “5.5.2 Checking the automatic cut-out”

• Carry out the necessary measurements to validate the correct

force limitation.

NOTICE

Material damage resulting from incorrect programming of

the door operator.

After a reset, all the parameters are returned to the factory settings.

Safety elements that are operational and are connected to the system

will be recognised anew after a reset.

To ensure that the controls functions properly:

• Reprogram all the required functions.

• Reprogram the remote control.

• Drive the operator system once to the OPEN position and then the

CLOSED position.

If a photocell is connected, it will be automatically detected by the

control system as soon as the power supply is connected.

The photocell can be reprogrammed later.

Photocells that are not required must be disconnected before the

power supply is connected; otherwise they will be recognised by the

controls.

➔ “4.5.3 Terminal block XB03”

CHECK

A function test must be carried out after changes have been made in

programming mode.

➔ “5.5 Function test”

18 Operating instructions, Comfort 260 accu (#114332 – GB)

5.6.1 Programming the special functions

Programming procedure

The control system is in

operating mode.

P > 10 sec.:

Start programming the

extended operator functions.

Display the levels.

Select the level required

(example: Level 2).

Conrmthelevelrequired.

Displaytherstmenuandthe

programmed parameter.

Select the menu required

(example Menu 3).

Conrmthemenurequired.

Display the programmed

parameter value.

7. Change the parameter value.

Save the parameter value.

The control system switches to

display the levels.

Select the next level required.

Continue programming.

P > 5 sec.:

Finish programming.

All the altered parameters are

saved.

The control system is in

operating mode.

5.6.2 Overview of the special functions

Level Menu

Basic functions

3 Intermediate OPEN position

4 Intermediate CLOSE position

8 RESET

Operator settings

1 Driving power required to OPEN

2 Driving power required to CLOSE

3 Automatic cut-out in the OPEN direction

4 Automatic cut-out in the CLOSE direction

Automatic closing

timer

1 Automatic closing timer

3 Door open duration

4 Warning time

5 Start-up warning

Remote

programming

2 Intermediate OPEN position

3 Intermediate CLOSE position

4 OPEN

5 CLOSE

Special functions

1 Programmable impulse input

4 Lighting duration

Variable

speed

1 OPEN speed

2 Soft run OPEN speed

3 Soft run OPEN position

4 CLOSE speed

5 Smart run CLOSE speed

6 Soft run CLOSE speed

7 Smart run CLOSE position

8 Soft run CLOSE position

9 Soft start time OPEN

10 Soft start time CLOSE

Maintenance and

servicing

1 Door cycle counter

2 Servicing counter

3 Servicing interval

8 Reset maintenance and servicing

9 Fault indicator

System settings

1 Photocell

3 Automatic cut-out function

4 Operating modes

5 Function of the direction command

transmitters

6 Function of the impulse command

transmitters

7 Stress relief in the CLOSED door position

(back jump)

8 Direction of rotation

Operating instructions, Comfort 260 accu (#114332 – GB) 19

5.6.3 Contents of the special functions

Level 1 – Basic functions

Menu 3 – Intermediate OPEN position

Adjust the setting using the + (OPEN) and – (CLOSE)

buttons.

The closing function with automatic closing is possible.

Only the intermediate position that was programmed last

can be used.

Menu 4 – Intermediate CLOSE position

Adjust the setting using the + (OPEN) and – (CLOSE)

buttons.

The closing function with automatic closing is not possible.

Only the intermediate position that was programmed last

can be used.

Menu 8 – RESET

The operator system can be reset to the factory settings.

1 ) No reset

2 Reset the controls

3 Reset the remote control (telegrams are deleted)

Reset the special function: automatic closing timer

➔ “Level 3 - Automatic closing timer”

Reset only the special operator functions (except

the OPEN/CLOSED door positions and the remote

control impulse)

6 Reset the safety elements (photocell / Hold circuit)

Reset bus modules (connected bus modules will be

programmed in)

Level 2 – Door operator settings

Menu 1 – Driving power required to OPEN

Sensitivity in on a scale of 1 to 16

(the higher the number, the greater the driving power).

) 8

Menu 2 – Driving power required to CLOSE

Sensitivity in on a scale of 1 to 16

(the higher the number, the greater the driving power).

) 8

Menu 3 – Automatic cut-out in the OPEN direction

Sensitivity on a scale of 1 (OFF) to 16

(the lower the number, the more sensitive the automatic

cut-out).

) 10

Level 2 – Door operator settings

Menu 4 – Automatic cut-out in the CLOSE direction

Sensitivity on a scale of 1 (OFF) to 16

(the lower the number, the more sensitive the automatic

cut-out).

) 8

Level 3 - Automatic closing timer

Menu 1 – Automatic closing timer

If the automatic closing function is activated, the relay

output (Level 1 / Menu 7) can be reprogrammed if

required.

1 ) Deactivated

Door open

duration 15 /

Warning time 5

The open duration can

only be increased via an

impulse signal

(button or hand

transmitter).

Door open

duration 30 /

Warning time 5

Door open

duration 60 /

Warning time 8

Door open

duration 15 /

Warning time 5

The door open duration

ends after the photocell

has been triggered.

Door open

duration 30 /

Warning time 5

Door open

duration 60 /

Warning time 8

Door open

durationinnite/

Warning time 3

Door closes after the

photocell has been

triggered /

Closing prevention.

Menu 3 – Door open duration

2 – 250 seconds.

) Dependent on Level 3, Menu 1

Menu 4 – Warning time

1 – 70 seconds.

) Dependent on Level 3, Menu 1

Menu 5 – Start-up warning

0 – 7 seconds.

) 0

20 Operating instructions, Comfort 260 accu (#114332 – GB)

Level 6 – Variable speed

Menu 1 – OPEN speed

On a scale of 5 to 16.

) 16

Menu 2 – Soft run OPEN speed

On a scale of 1 to 16.

) 8

Menu 3 – Soft run OPEN position

Adjust the setting using the + (OPEN) and – (CLOSE)

buttons.

Menu 4 – CLOSE speed

On a scale of 5 to 16.

) 16

Menu 5 – Smart run CLOSE speed

On a scale of 5 to 16.

) 8

Menu 6 – Soft run CLOSE speed

On a scale of 1 to 16.

) 8

Menu 7 – Smart run CLOSED position

Adjust the setting using the + (OPEN) and – (CLOSE)

buttons.

Menu 8 – Soft run CLOSE position

Adjust the setting using the + (OPEN) and – (CLOSE)

buttons.

Menu 9 – Soft start time OPEN

1 ) Soft start time 1 second

2 Soft start time 2 seconds

3 Soft start time 3 seconds

4 Soft start time 6 seconds

Menü 10 – Soft start time CLOSE

1 ) Soft start time 1 second

2 Soft start time 2 seconds

3 Soft start time 3 seconds

4 Soft start time 6 seconds

Level 4 – Remote programming

Menu 2 – Intermediate OPEN position

Parameterindicatorashes->Pressthehandtransmitter

button->Handtransmitterdisplayalsoashes->

The function has been programmed.

Menu 3 – Intermediate CLOSE position

Parameterindicatorashes->Pressthehandtransmitter

button->Handtransmitterdisplayalsoashes->

The function has been programmed.

Menu 4 – OPEN

Parameterindicatorashes->Pressthehandtransmitter

button->Handtransmitterdisplayalsoashes->

The function has been programmed.

Menu 5 – CLOSE

Parameterindicatorashes->Pressthehandtransmitter

button->Handtransmitterdisplayalsoashes->

The function has been programmed.

Level 5 – Special functions

Programming of the special functions is dependent on terminal block

XB03.

➔ “4.5.3 Terminal block XB03”

Menu 1 – Programmable impulse input (terminal 1/2)

1 ) Impulse (normally open contact only)

Closing prevention device (normally open contact

only)

Stops and reverses (only in the CLOSE direction –

normally closed contact only)

Stops and reverses (only in the CLOSE direction –

normally open contact only)

OPEN impulse (induction loop – normally open

contact only)

Earlier closing possible by pressing the buttons on

the input device or hand transmitter > 2 seconds

Impulse (normally open contact only)

with permanent 24 V DC / max. 50 mA

power supply

Menu 4 – Lighting duration

2 – 250 seconds.

) 1.2 (80 seconds)

Page is loading ...

Marantec Comfort 260 Owner's manual

Brand: Marantec

Model: Comfort 260

Category: Garage Door Opener

Type: Owner's manual

This manual is also suitable for

Comfort 260 accu

Download PDF

report

Marantec Comfort 260 Owner's manual

This manual is also suitable for

Marantec Comfort 260 Owner's manual

Related papers

Other documents