Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
CD-ES777 Mini Component System consisting of CD-ES777 (main unit)
and CP-ES777 (speaker system).
Note:
Only the above accessories are included.
Remote control 1
(RRMCGA087AWSA)
AM loop antenna 1
(QANTL0010AWZZ)
FM antenna 1
(FANT1535A)
Accessories
Please confirm that the following accessories are included.
MINI COMPONENT SYSTEM
MODEL
CD-ES777
OPERATION MANUAL
05/12/2 CD-ES777(U)1.fm
2
TINSEA095AWZZ
Important Instruction
CD-ES777
SPECIAL NOTES
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s en-
closure that may be of sufficient magnitude
to constitute a risk of electric shock to per-
sons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the lit-
erature accompanying the appliance.
0012
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
0012
Caution - use of controls or adjustments or performance
of procedures other than those specified herein may re-
sult in hazardous radiation exposure.
0012
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful in-
terference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to ra-
dio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
NOTE
It is the intent of Sharp that this product be used in full compliance with
the copyright laws of the United States and that prior permission be ob-
tained from copyright owners whenever necessary.
0210
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit.
Please retain this information.
Model number .......................................................
Serial number .......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0202
05/12/2 CD-ES777(U)1.fm
3
TINSEA095AWZZ
Important Instruction
CD-ES777
IMPORTANT SAFETY INSTRUCTIONS
1 Read Instructions - All the safety and operating instructions should
be read before the product is operated.
2 Retain Instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
5 Cleaning - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6 Attachments - Do not use attachments not recommended by the prod-
uct manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water - for ex-
ample, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufac-
turer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting ac-
cessory recommended by the manufacturer.
9 A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to over-
turn.
10 Ventilation - Slots and openings in the cabinet are provided for venti-
lation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or cov-
ered. The openings should never be blocked by placing the product on
a bed, sofa, rug, or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been
adhered to.
11 Power Sources - This product should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
12 Grounding or Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electri-
cian to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
13 Power-Cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them.
14 Protective Attachment Plug - The product is equipped with an at-
tachment plug having overload protection. This is a safety feature. See
Instruction Manual for replacement or resetting of protective device. If
replacement of the plug is required, be sure the service technician has
used a replacement plug specified by the manufacturer that has the
same overload protection as the original plug.
05/12/2 CD-ES777(U)1.fm
4
TINSEA095AWZZ
Important Instruction
CD-ES777
IMPORTANT SAFETY INSTRUCTIONS (continued)
15 Outdoor Antenna Grounding - If an outside antenna or cable system
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an an-
tenna discharge unit, size of grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
16 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
17 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
18
Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
19
Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
20 Servicing - Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
21 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the op-
erating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
22 Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23 Safety Check - Upon completion of any service or repairs to this prod-
uct, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
24 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
25 Heat - The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including ampli-
ANTENNA LEAD IN WIRE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
fiers) that produce heat.
05/12/2 CD-ES777(U)1.fm
5
TINSEA095AWZZ
Important Instruction
CD-ES777
Contents
Page
General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 9
Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 12
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the clock (Remote Control only) . . . . . . . . . . . . . . . . . 15
CD Playback
Listening to a CD (CDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 - 17
Advanced CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 20
Radio
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 - 22
Tape Playback
Listening to a cassette tape (TAPE 1 or TAPE 2) . . . . . . .23 - 24
Tape Recording
Recording on a cassette tape . . . . . . . . . . . . . . . . . . . . . . .24 - 26
Advanced Features
Timer and sleep operation (Remote Control only) . . . . . .27 - 30
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . .31 - 32
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 - 34
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . .Back cover
ENERGY STAR
®
Program Information
Products that have earned
the ENERGY STAR
®
are
designed to protect the
environment through
superior energy efficiency.
To comply with the ENERGY STAR
®
standards mentioned above,
please cancel the demonstration mode, as described on page 12.
ENERGY STAR
®
is a U.S. registered mark.
05/12/2 CD-ES777(U)1.fm
6
TINSEA095AWZZ
General Information
CD-ES777
Precautions
General
Please ensure that the equipment is positioned in a well-ventilated
area and ensure that there is at least 4" (10 cm) of free space
along the sides, top and back of the equipment.
Do not place anything on top of the unit.
Do not expose the unit to moisture, to temperatures higher than
140˚F (60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and then
turn on your system.
This unit should only be used within the range of 41˚F - 95˚F
(5˚C - 35˚C).
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of
accident causing damage. SHARP will not be held responsible for
any damage resulting from use of this unit with a voltage other than
that which is specified.
Volume control
The sound level at a given volume setting depends on speaker
efficiency, location and various other factors. It is advisable to avoid
exposure to high volume levels, which occurs while turning the unit
on with the volume control setting up high, or while continually
listening at high volumes.
Use the unit on a firm, level surface free from
vibration.
Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical equip-
ment (home computers, facsimiles, etc.)
which generate electrical noise.
In case of an electrical storm, unplug the
unit for safety.
4" (10 cm)
4" (10 cm) 4" (10 cm)
4" (10 cm)
Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
Do not remove the outer cover, as this
may result in electric shock. Refer in-
ternal service to your local SHARP ser-
vice facility.
05/12/2 CD-ES777(U)1.fm
7
TINSEA095AWZZ
General Information
CD-ES777
Controls and indicators
Front panel
Reference page
1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
6. Tape (1 2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7. Game/Video Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8. Tape 1 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 23
9. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
10. Game/Video Input Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
11. Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 16
12. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 16
13. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
14. CD or Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . 17, 24
15. CD Play or Repeat, Tape Play Button . . . . . . . . . . 16, 19, 23
16. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button . . . . . . . . . . 15, 17, 22, 24
17. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button . . . . . 15, 17, 22, 24
18. Tape 2 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 23
19. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1
05/12/2 CD-ES777(U)1.fm
8
TINSEA095AWZZ
General Information
CD-ES777
Controls and indicators (continued)
Display
Reference page
1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2. CD Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3. CD Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5. CD Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6. CD Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. Tape Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
11. FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 21
12. Tape 2 Record Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
13. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
14. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
15. Timer Recording Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Rear panel
Reference page
1. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. FM 75 Ohms Antenna Jack b . . . . . . . . . . . . . . . . . . . . . . . . 11
4. AM Antenna Ground Terminal . . . . . . . . . . . . . . . . . . . . . . 11
5. AM Loop Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Speaker Light-Up Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7. Video Output Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Speaker system
8
76321 4 5
13 14 15
10911
12
AC INPUT
1. Tweeter
2. Super Tweeter
3. Woofer
4. Bass Reflex Duct
5. Speaker Wire
6. Speaker Light-Up wire
1
2
3
4
5
6
05/12/2 CD-ES777(U)1.fm
9
TINSEA095AWZZ
General Information
CD-ES777
Remote control
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 13
2. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 16
3. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 15, 27, 30
4. Disc Direct Search Buttons . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 14
6. Extra Bass/Demo Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 14
8. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
9. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
10. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
11. Tape (1 2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
12. Game/Video Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
13. CD Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . 14, 20
14. CD Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
15. CD Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
16. Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
17. Memory Button . . . . . . . . . . . . . . . . . . . . . . . 15, 20, 22, 27, 30
18. CD Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
19. CD Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . . 16, 19
20. Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
21. Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . 25, 26
22. Tuning Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
23. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button . . . . 15, 17, 22, 24, 27, 30
24. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button 15, 17, 22, 24, 27, 30
25. Tuning Down Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1
2
3
5
6
7
4
9
10
8
11
12
17
19
18
13
15
14
21
20
16
25
24
22
23
1
05/12/2 CD-ES777(U)1.fm
10
TINSEA095AWZZ
Preparation for Use
CD-ES777
System connections
AC INPUT
AC outlet
(AC 120 V, 60 Hz)
AC power connection (see page 12)
Right speaker
AM loop antenna
Make sure to unplug the AC power cord before any connections.
Antenna connection (see page 11)
Speaker connection (see page 11)
Left speaker
Speaker light-up wire
Speaker light-up wire
FM antenna
11
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
Preparation for Use
CD-ES777
Antenna connection
Note:
Placing the antenna on the unit or near the AC power cord may
cause noise pickup. Place the antenna away from the unit for better
reception.
Installing the AM loop antenna:
Speaker connection
Connect the black wire to the minus (-) terminal, and the red wire to
the plus (+) terminal.
Caution:
Speaker Light-Up Connection
Connect the speaker light-up wires to the SPEAKERS LIGHT-UP
jacks for speaker illumination. To turn off the speaker light-up
feature, press the CLEAR/DIMMER button on the remote control for
2 seconds or more.
Note:
Placing the right speaker light-up wire to the RIGHT jack and the left
speaker light-up wire to the LEFT jack.
Supplied FM antenna:
Connect the FM antenna wire to the
FM 75 OHMS jack and position the FM
antenna wire in the direction where the
strongest signal can be received.
Supplied AM loop antenna:
Connect the AM loop antenna to the
AM and GND terminals. Position the
AM loop antenna for optimum
reception. Place the AM loop antenna
on
a shelf, etc., or attach it to a stand
or a wall with screws (not supplied).
< Assembling > < Attaching to the wall >
Wall Screws (not supplied)
ANTENNA
FM
75 OHMS
AM
GND
AM loop
antenna
FM
antenna
White
Black
Use speakers with an impedance of 6 ohms or more, as lower
impedance speakers can damage the unit.
Do not mistake the right and the left chan-
nels. The right speaker is the one on the right
side when you face the unit.
Do not let the bare speaker wires touch
each other.
Do not allow any objects to fall into or to be
placed in the bass reflex ducts.
Do not stand or sit on the speakers. You may
be injured.
Incorrect
AC INPUT
Blac
k
Red
AC INPUT
SPEAKERS
LIGHT-UP
RIGHT
LEFT
LEFT SPEAKER
RIGHT SPEAKER
2
12
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
Preparation for Use
CD-ES777
System connections (continued)
AC power connection
After checking all the connections have been made correctly, plug
the AC power cord of this unit into the AC outlet. If you plug in the unit
first, the unit will enter the demonstration mode.
Notes:
The unit will start the tape initialization when plugged in to the AC
outlet. During this process, an initializing sound will be heard and
the unit cannot be turned on. Wait until the process is finished.
Unplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
Demonstration mode
Outdoor FM antenna
Use an outdoor FM antenna if you require better reception. Consult
your dealer.
Note:
When an outdoor FM antenna is used, disconnect the supplied FM
antenna wire.
Cooling fan:
The main unit is built with a cooling fan at the rear of the unit for
improved cooling. Please do not cover the opening of the fan with
any obstacles, as this will block proper ventilation.
AC INPUT
AC outlet
(AC 120 V, 60 Hz)
AC INPUT
The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll.
To cancel the demonstration
mode:
When the unit is in the power stand-
by mode (demonstration mode),
press the X-BASS/DEMO button.
The unit will enter the low power
consumption mode.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/
DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to
select the extra bass mode.
Outdoor
FM antenna
75 ohms
coaxial cable
ANTENNA
FM
75 OHMS
AM
GND
13
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
Preparation for Use
CD-ES777
Remote control
Battery installation
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to
malfunction.
Battery removal:
Open the battery cover and pull up the battery to take out.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control
Check the remote control after checking all the connections (see
pages 10 - 12).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1 Open the battery cover.
2 Insert the batteries according to the direction indicated in
the battery compartment (back of the battery cover).
When inserting or removing the batteries, push them toward the
battery terminals.
3 Close the cover.
8" - 20"
(0.2 m - 6 m)
Remote sensor
2
14
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
Basic Operation
CD-ES777
General control
To turn the power on
Press the ON/STAND-BY button to turn the power on.
Illumination light control
When the power is turned on, light illuminates around the display. To
turn on/off the light, hold down the CLEAR/DIMMER button on the
remote control more than 2 seconds.
Speaker light up
The speaker will light up according to the level of the music source
played back. To turn on/off the light, hold down the CLEAR/DIMMER
button on the remote control for 2 seconds or more.
Volume auto fade-in
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
Volume control
Bass control
Equalizer
When the EQUALIZER MODE button is pressed, the current mode
setting will be displayed. To change to a different mode, press the
EQUALIZER MODE button repeatedly until the desired sound mode
appears.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
Main unit operation:
When the VOLUME control is turned
clockwise, the volume will increase.
When it is turned counterclockwise, the
volume will decrease.
Remote control operation:
Press the VOLUME (+ or -) button to
increase or decrease the volume.
When the power is first turned on, the unit
will enter the extra bass mode which
emphasizes the bass frequencies, and
"X-BASS" will appear. To cancel the extra
bass mode, press the X-BASS/DEMO
button
.
In CD/TUNER/TAPE mode In GAME/VIDEO mode
30 MAXIMUM0
.....
For rock music.
For pop music.
No equalization.
For classical music.
For jazz.
FLAT
ROCK
CLASSIC
POPS
VOCAL
JAZZ
Vocals are
enchanced.
For car racing
games.
For sports games.
For action games.
No equalization.
ACTION
SPORTS
RACING
For rock music.
For classical
music.
FLAT
ROCK
CLASSIC
15
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
Basic Operation
CD-ES777
Setting the clock (Remote Control only)
In this example, the clock is set for the 12-hour (AM 12:00) display.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.
[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the or button to display the
time. The time display will appear for about 10 seconds.
Note:
The "CLOCK" will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" is not
appear in step 3, step 4 (for selecting the 12-hour or 24-hour
display) will be skipped.
To change the 12-hour or 24-hour display:
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press
the
or
button
to
select "CLOCK", and press the MEMORY button.
4
Press the or button to select 12-hour or 24-hour
display and then press the MEMORY button.
"AM 12:00" The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00" The 12-hour display will appear.
(AM 0:00 - PM 11:59)
"0:00" The 24-hour display will appear.
(0:00 - 23:59)
5
Press
the
or
button
to adjust the hour and then
press the MEMORY button.
Press
the
or
button
once to advance the time by
1 hour. Hold it down to advance continuously.
6
Press
the
or
button
to adjust the minutes and
then press the MEMORY button.
Press
the
or
button
once to advance the time by
1 minute. Hold it down to change the time in 5-minute intervals.
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 33 for details.]
2 Perform "Setting the clock" from step 1.
3
16
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
CD Playback
CD-ES777
Listening to a CD (CDs)
This system can also play audio CD-R and CD-RW discs, but cannot
record.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the device that was used for recording.
CD playback
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the 1 button and within 5 seconds, press the
button to open the disc tray 1.
4
Place the CD on the disc tray 1, label side up.
Be sure to place 3" (8 cm) CD in the middle of the disc trays.
5
Press the button to close the disc tray 1.
Total number of tracks on
the CD whose number is
flashing
Total playing time of the
CD whose number is
flashing
" " will appear.
6
You can place discs on the trays 2 - 5 by following steps
3 - 5.
7
Press the / button to start playback.
5" (12 cm) 3" (8 cm)
CD play indicator
17
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
CD Playback
CD-ES777
Playback will begin from track 1 on the DISC 1. After that disc
finishes playing, the next disc will automatically play.
After the last track on the fifth disc is played, the CD player stops
automatically.
When there is no CD in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a CD.
To exchange other CDs while playing a disc:
Press one of the 1 - 5 buttons for the stopped disc and within 5
seconds, press the
button and exchange discs.
To remove the CDs:
In the stop mode, press the 1 - 5 button and within 5 seconds,
press the button.
Caution:
Do not place two CDs in one disc tray.
Do not play discs of special shapes (heart, octagon, etc). It may
cause malfunctions.
Do not push the disc tray while it is moving.
If the power fails while the tray is open, wait until the power is
restored.
If the disc tray is stopped with force, "ER-CD20" will appear on
the display for 3 seconds and the unit will not function. If this
occurs, press the ON/STAND-BY button to enter the power
stand-by mode and then turn the power on again.
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
If a disc is damaged, dirty, or loaded upside down, the disc will be
skipped.
Auto power on function:
When you press any of the following buttons, the unit turns on.
CD button (main unit and remote control): The unit turns on and
the "CD" function is activated.
button (main unit): The unit turns on and playback of the last
function starts (CD, TAPE, TUNER, GAME/VIDEO).
CD / button (remote control): The unit turns on and the "CD"
function is activated.
Various CD functions
Notes:
Function Main unit Remote
control
Operation
Play Press in the stop
mode.
Stop Press in the playback
mode.
Pause Press in the playback
mode. Press the /
button to resume play-
back from the paused
point.
Track up/
Track down
Press in the playback
or stop mode.
If you press the button
in the stop mode,
press the / button
to start the desired
track.
Fast for-
ward/Fast
reverse
Press and hold down
in the playback mode.
Release the button to
resume playback.
Track up/track down and fast forward/fast reverse are possible
only within individual discs.
When the end of the last track is reached during fast forward,
"END" will appear on the display and CD operation will be paused.
When the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
4
18
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
CD Playback
CD-ES777
Advanced CD playback
To specify a disc to play
You can play a disc by specifying the disc number.
Playback will begin from track 1 on the chosen disc.
After the last track on the last disc is played, the CD player stops
automatically.
Note:
If the button of the disc tray with no disc is pressed, playback will not
start and the disc indicator will go out.
To stop playback:
Press the (CD ) button.
Direct track search
By using the direct search buttons, the desired tracks on the current
disc can be played.
If the direct search buttons are pressed while the disc is stopped,
press the / button to start the desired track on the current disc.
Notes:
A track number higher than the number of tracks on the disc
cannot be selected.
During random play, direct search is not possible.
1 Press one of the 1 - 5 buttons to select the desired disc.
Selected disc number
2 Within 5 seconds, press the button on the main unit.
Use the direct search buttons on
the remote control to select the
desired track while playing the
selected disc.
Selected track number
The direct search buttons allow you to select up to number 9.
When selecting number 10 or more, use the "+10" button.
A. For example, to choose 13
1 Press the "+10" button once.
2 Press the "3" button.
B. For example, to choose 30
1 Press the "+10" button three times.
2 Press the "0" button.
19
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
CD Playback
CD-ES777
Repeat play
Repeat play can play all 5 discs, all tracks on a chosen disc, or a
programmed sequence continuously.
To cancel repeat play:
Press the / button again.
" " will go out.
Random play
The tracks on the disc(s) can be played in random order automatically.
To cancel random play:
Press the / button.
"R" will go out.
Notes:
If you press the button during random play, you can move to
the track selected next by the random operation. On the other
hand, the button does not allow you to move to the previous
track. The beginning of the track being played will be located.
In random play, the CD player will select and play tracks
automatically. (You cannot select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the (CD )
button. Otherwise, the disc(s) will play continuously.
To repeat all tracks on up to 5 discs:
Press the / button twice.
To repeat desired tracks:
Perform steps 1 - 6 in the "Programmed play" section on page 20
and then press the / button twice.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.
4
20
05/12/2 CD-ES777(U)2.fm
TINSEA095AWZZ
CD Playback
CD-ES777
Advanced CD Playback (continued)
Programmed play
You can choose up to 32 selections for playback in the order you like.
To cancel the programmed play mode:
While in the stop mode and the "MEMORY" indicator is lit, press the
CLEAR/DIMMER button on the remote control. The "MEMORY"
indicator will disappear and all the programmed contents will be
cleared.
Adding tracks to the program:
If a program has been previously stored, the "MEMORY" indicator
will be displayed. Then follow steps 1 - 6 to add tracks. The new
tracks will be stored after the last track of the original program.
To check which tracks are programmed:
While the unit is stopped in the programmed play mode, press the
or button.
Notes:
When a disc with programmed tracks is ejected, the program is
automatically canceled.
Even if you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the programmed
selections will not be cleared.
During the program operation, random play is not possible.
1 While in the stop mode, press the
MEMORY button to enter the pro-
gramming save mode.
2 Press one of the 1 - 5 buttons
to select the desired disc.
Selected disc number
3 Press the direct search buttons
on the remote control to select
the desired track.
Selected track number
You can also select a track by pressing the or button.
4
Press the MEMORY
button to save
the track number.
5 Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be
programmed.
If you make a mistake, the programmed tracks can be cleared
by pressing the CLEAR/DIMMER button.
6 Press the button.
The total number in memory will
appear.
7 Press the / button to start playback.
To clear the programmed selections:
Press the CLEAR/DIMMER button on the
remote control while the "MEMORY" indicator
is flashing.
Each time the button is pressed, one track will
be cleared, beginning with the last track
programmed.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/